View BD3539FVM_9092729.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

product structure silicon monolithic integrated circuit this product has no designed protec tion against radioactive rays 1/18 tsz22111 ? 14 ? 001 ? 2014 rohm co., ltd. all rights reserved. tsz02201-0j2j0a900710-1-2 22.jul.2015 rev.002 www.rohm.com 1.0v to 5.5v, 1a 1ch termination regulators for ddr-sdrams BD3539FVM bd3539nux general description bd3539 is a termination regulator that complies with jedec requirements for ddr1-sdram, ddr2-sdram, and ddr3-sdram. this linear power supply uses a built-in n-channel mosfet and high-speed op-amps specially designed to provide excellent transient response. it has a sink/source current capability of up to 1a and has a power supply bias requirement of 3.3 v (for ddr2 and ddr3) and 5.0 v (for ddr1, ddr2, and ddr3) for driving the n-channel mosfet. by employing an independent reference voltage input (vddq) and a feedback pin (vtts), this termination regulator provides excellent output voltage accuracy and load regulation as required by jedec standards. additionally, bd3539 has a reference power supply output (vref)for ddr-sdram or for memory controllers. unlike the vtt output that goes to hi-z state, the vref output is kept unchanged when en input is changed to low, making this ic suitable for ddr-sdram under self refresh state. features ? incorporates a push-pull power supply for termination (vtt) ? incorporates a reference voltage circuit (vref) ? incorporates an enabler ? incorporates an under voltage lockout (uvlo) ? incorporates a thermal shutdown protector (tsd) ? compatible with dual channel (ddr1, ddr2, ddr3) ? usable ceramic capacitor at output applications power supply for ddr 1/2/3 - sdram key specifications ? termination input voltage range: 1.0v to 5.5v ? vcc input voltage range: 2.7v to 5.5v ? vddq reference voltage range: 1.0v to 2.75v ? output voltage: 1/2xv ddq v(typ) ? output current: 1.0a (max) ? high side fet on-resistance: 0.35 ? (typ) ? low side fet on-resistance: 0.35 ? (typ) ? standby current: 0.5ma (typ) ? operating temperature range: -30c to +100c packages w(typ) x d(typ) x h(max) typical application circuit, block diagram msop8 2.90mm x 4.00mm x 0.90mm v son008x2030 2.00mm x 3.00mm x 0.60mm vcc vcc vddq vddq vtt_in v cc v cc v cc soft uvlo tsd reference block thermal protection enable en gnd vref vtts v ddq ? x vtt vtt vtt_in uvlo tsden uvlo tsd en uvlo v cc tsden uvlo en 1 2 4 3 8 7 5 6 c 2 c 3 c 4 c 1 datashee t downloaded from: http:///
2/18 datasheet d a t a s h e e t BD3539FVM bd3539nux ? 2014 rohm co., ltd. all rights reserved. tsz22111 ? 15 ? 001 22.jul.2015 rev.002 tsz02201-0j2j0a900710-1-2 www.rohm.com pin configurations fvm nux pin descriptions pin no. pin name pin function 1 gnd ground pin 2 en enable input pin 3 vtts detector pin for termination voltage 4 vref reference voltage output pin 5 vddq reference voltage input pin 6 vcc vcc pin 7 vtt_in termination input pin 8 vtt termination output pin pin no. pin name pin function 1 vtt_in termination input pin 2 vtt termination output pin 3 gnd ground pin 4 en enable input pin 5 vtts detector pin for termination voltage 6 vref reference voltage output pin 7 vddq reference voltage input pin 8 vcc vcc pin bottom fin substrate (connected to gnd) description of blocks 1. vcc the vcc pin is for the independent power supply input that operates the internal circuit of the ic. it is the voltage at this pin that drives the ics amplifier circ uits. the vcc input ranges from 2.7v to 5.5v and maximum current consumption is 4ma. a bypass capacitor of 1 f or so should be connected to this pin when using the ic in an application circuit. 2. vddq this is the power supply input pin for an internal voltage divider network. the voltage at vddq is halved by two 100k ? internal voltage-divider resistors and the resulting vo ltage serves as reference for the vtt output. since v ref =v tt = 1/2v ddq , the jedec requirement for ddr-sdram can be sati sfied by supplying the correct voltage to vddq. noise input should be avoided at the vddq pin as it is also included by the volt age-divider at the output. an rc filter consisting of a resistor and a capacitor (220 ? and 2.2 f, for instance,) may be used to reduce the noise input but make sure that it will not significantly affe ct the voltage-dividers output. the ic. 3. vtt_in vtt_in is the power supply input pin for the vtt output. input voltage may range from 1.0v to 5.5v, but consideration must be given to the current limit dict ated by the on-resistance of the ic and to the change in allowable loss due to input/output voltage difference. generally, the following voltages are supplied: ? ddr3 vtt_in = 1.5v ? ddr2 vtt_in = 1.8v ? ddr1 vtt_in = 2.5v take note that a high-impedance voltage in put at vtt_in may result in oscillation or degradation in ripple rejection, so connecting a 10f capacitor with minimal change in capacitance to vtt_in terminal is recommended. however, this impedance may depend on the characteristics of the power supply input and the impedance of the pc board wiring, which must be carefully checked before use. vtt_in gnd en vtts vref vtt vcc vddq 1 2 3 4 5 6 7 8 top view vddq vtt_in vtt gnd en vcc vref vtts 1 2 3 4 5 6 7 8 top view downloaded from: http:///
3/18 datasheet d a t a s h e e t BD3539FVM bd3539nux ? 2014 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 ? 15 ? 001 22.jul.2015 rev.002 tsz02201-0j2j0a900710-1-2 description of blocks C continued 4. vref bd3539 provides a constant voltage, vref, which is independ ent from the vtt output and can serve as reference input for memory controllers and drams. the voltage level of vref is kept constant ev en if the en pin is at low level, making the use of this ic compatible wi th the self refresh state of drams. in order to stabilize the output voltage, connecting the correct combination of capaci tor and resistor to vref is necessary. for this purpose, a 1.0 f to 2.2 f ceramic capacitor, characterized by minimal variation in capacitance, is recommended. the maximum current capability of the vref pin is 25ma, but for an applicati on which consumes a small amount of vref current (1ma or less), using a capacitance of 0.1 f or less will do. 5. vtts vtts is a sense pin for the load regulation of the vtt output voltage. in case the wire connecting vtt pin and the load is too long, connecting vtts pin to the part of t he wire nearer to the load may improve load regulation. vtts terminal is high impedance terminal. therefore it is easy to be affected by the noise. the stable operation of the ic is possible by inserting rc filter (e.g.,: r=200 ? , c=1000pf) near vtts terminal. 6. vtt this is the output pin for the ddr memory termination voltage an d it has a sink/source current capability of 1.0a. vtt voltage tracks the voltage at vddq pin divided in half. the output is turned off when en pin is low or when either the vcc uvlo or the thermal shutdown protection function is activated. always connect a capacitor to vtt pin for loop gain and phase compensation and for reduction in output voltage variation in the event of sudden load change. be careful in choosing the capacitor as insufficient capacitance may cause oscillation and high esr (equivalent series resistance) may result in increased output voltage vari ation during a sudden change in load. a 10f or so ceramic capacitor is recommended, though ambient temperature and other conditions should also be considered. 7. en a high input of 2.3v or higher to en turns on the vtt ou tput. a low input of 0.8v or less, on the other hand, turns vtt to a hi-z state. with a low en input, however, the vref output remains on, provid ed that sufficient vcc and vddq voltages have been established. when en terminal repeats on/off, an inrush current may flow in vtt_in terminal. please be careful about voltage drop of the vtt_in line. absolute maximum ratings parameter symbol limit unit BD3539FVM bd3539nux input voltage v cc 7 (note 1) v enable input voltage v en 7 (note 1) v termination input voltage v tt_ in 7 (note 1) v vddq reference voltage v ddq 7 (note 1) v output current i tt 1 a power dissipation1 pd1 0.38 (note 2) 0.24 (note 4) w power dissipation2 pd2 0.58 (note 3) 0.51 (note 5) w power dissipation3 pd3 - 0.87 (note 6) w operating temperature range topr -30 to +100 c storage temperature range tstg -55 to +150 c maximum junction temperature tjmax +150 c (note 1) should not exceed pd. instantaneous surge voltage, back el ectromotive force and voltage under less than 10% duty cycle . (note 2) for ta 25c (with no heat sink) ja=322.6c /w (note 3) for ta 25c when mounting a 70mm x 70mm x 1.6mm glass-epoxy substrate, with no heat sink ja=212.8c /w (note 4) for ta 25c (with no heat sink) ja=516.5c /w (note 5) for ta 25c when mounting a 70mm x 70mm x 1.6mm glass-epoxy substrate 1-layer board, ja=242.7c /w (note 6) for ta 25c when mounting a 70mm x 70mm x 1.6mm glass-epoxy substrate 4-layer board (copper foil density: 5505mm 2 (copper foil area in each layer)), ja=142.5c /w caution: operating the ic over the absolute maximum ratings may damage t he ic. in addition, it is impossible to predict all destructive situations such as short-circuit modes, open circuit modes, etc. therefore, it is im portant to consider circuit protection measures, like adding a fuse, in case the ic is operated in a special mode exceeding the absolute maximum ratings. downloaded from: http:///
4/18 datasheet d a t a s h e e t BD3539FVM bd3539nux ? 2014 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 ? 15 ? 001 22.jul.2015 rev.002 tsz02201-0j2j0a900710-1-2 recommended operating ratings (ta=25c) parameter symbol limit unit min max input voltage v cc 2.7 5.5 v termination input voltage v tt _ in 1.0 5.5 v vddq reference voltage v ddq 1.0 2.75 v enable input voltage v en -0.3 +5.5 v electrical characteristics (unless otherwise noted, ta=25c, v cc =3.3v, v en =3v, v ddq =1.5v, v tt_ in =1.5v) parameter symbol limit unit conditions min typ max standby current i stby - 0.5 1.0 ma v en =0v circuit current i cc - 2 4 ma v en =3v [enable] high level enable input voltage v enhigh 2.3 - 5.5 v low level enable input voltage v enlow -0.3 - +0.8 v enable pin input current i en - 7 10 a v en =3v [termination] termination output voltage (ddr3) v tt3 1/2xv ddq -15m 1/2xv ddq 1/2xv ddq +15m v i tt =-1.0a to +1.0a ta=0c to 100c termination output voltage (ddr2) v tt2 1/2xv ddq -30m 1/2xv ddq 1/2xv ddq +30m v v cc = 3.3v, v ddq = 1.8v v tt_ in = 1.8v i tt =-1.0a to +1.0a ta=0c to 100c termination output voltage (ddr1) v tt1 1/2xv ddq -30m 1/2xv ddq 1/2xv ddq +30m v v cc = 5.0v, v ddq = 2.5v v tt_ in = 2.5v i tt =-1.0a to +1.0a ta=0c to 100c source current i tt+ 1.0 - - a sink current i tt- - - -1.0 a load regulation ? v tt - - 30 mv i tt =-1.0a to +1.0a upper side on-resistance r on_h - 0.35 0.65 ? lower side on-resistance r on_l - 0.35 0.65 ? [vddq] input impedance z vddq 140 200 260 k ? [vref] output voltage v ref 1/2xv ddq -15m 1/2xv ddq 1/2xv ddq +15m v i ref =-25ma to +25ma ta=0c to 100c [uvlo] threshold voltage v uvlo 2.30 2.45 2.60 v v cc : sweep up hysteresis voltage ? v uvlo 100 160 220 mv v cc : sweep down downloaded from: http:///
5/18 datasheet d a t a s h e e t BD3539FVM bd3539nux ? 2014 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 ? 15 ? 001 22.jul.2015 rev.002 tsz02201-0j2j0a900710-1-2 typical performance curves figure 1. termination output voltage vs output current (ddr3) output current : i tt [a] termination output voltage : v tt [mv] 748.5 749.0 749.5 750.0 750.5 751.0 751.5 -20 -10 0 10 20 iref[ma] vref [mv] figure 2. output voltage vs i ref (ddr3) i ref [ma] output voltage : v ref [mv] downloaded from: http:///
6/18 datasheet d a t a s h e e t BD3539FVM bd3539nux ? 2014 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 ? 15 ? 001 22.jul.2015 rev.002 tsz02201-0j2j0a900710-1-2 typical waveforms 10sec/div vref(50mv/div) vtt(50mv/div) itt(1a/div) sin k source 10sec/div vref(50mv/div) vtt(50mv/div) itt(1a/div) sink source vcc en vddq vtt_in vtt 2sec/div vcc en vtt 2sec/div figure 3. ddr3 (-1a to +1a) figure 4. ddr3 (+1a to -1a) figure 5. input sequence1 figure 6. input sequence 2 downloaded from: http:///
7/18 datasheet d a t a s h e e t BD3539FVM bd3539nux ? 2014 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 ? 15 ? 001 22.jul.2015 rev.002 tsz02201-0j2j0a900710-1-2 typical waveforms C continued 200sec/div vcc en vddq vtt_in vtt 2sec/div figure 7. input sequence 3 figure 8. en soft start vtt vddq vref figure 9. vddq soft start downloaded from: http:///
8/18 datasheet d a t a s h e e t BD3539FVM bd3539nux ? 2014 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 ? 15 ? 001 22.jul.2015 rev.002 tsz02201-0j2j0a900710-1-2 application information 1. evaluation board part no value company parts name part no value company parts name u1 - rohm BD3539FVM c4 - - - r1 - - - c5 10f kyocera cm21b106m06a r4 220 rohm mcr032200 c6 - - - j1 0 - - c7 10f kyocera cm21b106m06a j2 0 - - c8 - - - c1 - - - c9 2.2f kyocera cm105b225k06a c2 1f kyocera cm105b105k06a c10 - - - c3 1f kyocera cm105b105k06a c11 - - - BD3539FVM evaluation board application components silk screen top layer bottom layer BD3539FVM evaluation board layout BD3539FVM evaluation board circuit c 5, c 6 gnd en vcc vddq vtt_in gnd v cc sw1 c 11 j 2 r 4 c 9 j 1 c 3 ,c 4 c 7 c 8 c 10 c 2 c 1 r 1 2 7 5 6 1 8 3 4 u1 vtt_in vcc vtt vref vddq en vtts gnd BD3539FVM vref vtts vtt downloaded from: http:///
9/18 datasheet d a t a s h e e t BD3539FVM bd3539nux ? 2014 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 ? 15 ? 001 22.jul.2015 rev.002 tsz02201-0j2j0a900710-1-2 2. example of layout pattern the input capacitor cin of vtt_in should be placed as close as possible to vtt_in pin. similarly, the vtt output capacitor should be placed as close as possible to the ics pin. as fo r wiring pattern, make the pin wiring and the gnd pattern as wide as possible. as for the metal trace connecting to t he inner gnd plane, please place many through holes. since vtts pin has comparatively high impedance, floating capacitance should be as small as possible and design layout at upper layer pattern. please be careful in drawing. please make the gnd pattern space wide and design the layout with the ability to increase radiation efficiency. [example of board layout pattern] [pin configuration] downloaded from: http:///
10/18 datasheet d a t a s h e e t BD3539FVM bd3539nux ? 2014 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 ? 15 ? 001 22.jul.2015 rev.002 tsz02201-0j2j0a900710-1-2 3. power dissipation in thermal design, consider the te mperature range wherein the ic is guar anteed to operate and apply appropriate margins. the temperature conditions that need to be considered are listed below: (1) ambient temperature ta: 100c or lower (2) chip junction temperature tj: 150c or lower the chip junction temperature tj can be considered as follows: (a) calculation based on ic surface temperature tc, mounted on a board j-c:msop-8 46.0c/w pcb size: 70x70x1.6mm (board copper foil area: 70x70mm 2 ) (b) calculation based on ambient temperature ta j-a:msop-8 212.8c/w with no heat sink 322.6c /w 1-layer board (copper foil area :70x70mm 2 ) j-a:vson008x2030 516.5c /w with no heat sink 242.7c /w 1-layer board(copper foil area:70x70mm 2 ) 142.5c /w 4-layer board(copper foil area:70x70mm 2 ) pcb size: 70x70x1.6mm 3 (with thermal via) since the package has the fin at the bottom of the ic, package power is considerab ly affected by the area of the copper foil where fin is connected. in order to release hea t, please make the board area large enough or add many through-holes to the inner layer pattern. most heat loss in bd3539 occurs at the output n-channel fet. the lost power is determined by multiplying the voltage between in and out by the output current. since this ic is packaged for high-power applications, its thermal derating characteristics significantly depend on the pc board. so when designing, the size of the pc board to be used should be carefully considered. power consumption (w) = input voltage (v tt_in ) - output voltage (v tt v ddq ) x i out (ave) example) where v tt_ in =1.5v, v ddq =1.5v, i out (ave)= 0.5a ?? ?? ? ? ?? ? ? ?? w a v v w n consumptio power 375 .0 5.0 75.0 5.1 ? ? ? ? 1 2 w c j tc tj ? ? ? ? ? w a j ta tj ? ? ? ? ? downloaded from: http:///
11/18 datasheet d a t a s h e e t BD3539FVM bd3539nux ? 2014 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 ? 15 ? 001 22.jul.2015 rev.002 tsz02201-0j2j0a900710-1-2 heat dissipation characteristics [tc] msop8 heat dissipation characteristics [ta] msop8 vson008x2030 2.72w [w] 0 25 75 100 125 50 1.0 0.5 0 3.0 2.5 150 [c] 1-layer board ja=46.0c/w 2.0 1.5 ambient temperature [ta] ambient temperature [ta] power dissipation [pd] [w] 0 25 75 100 125 150 50 [c] 0.5 0.25 0 1.0 0.75 (1) 877.2mw (2) 515.0mw (3) 242.0mw (1) 4-layer board (copper foil area : 5505mm 2 ) every layer has copper foil area, ja=142.5c /w (2) 1-layer board ja=242.7c /w (3) with no heat sink ja=516.5c /w 150 [c] power dissipation [pd] ambient temperature [ta] (1) 587.4mw [mw] 0 25 75 100 125 50 200 100 0 600 500 400 300 (2) 387.4mw (1) 1-layer board ja=212.8c /w (2) with no heat sink ja=322.6c /w power dissipation [pd] downloaded from: http:///
12/18 datasheet d a t a s h e e t BD3539FVM bd3539nux ? 2014 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 ? 15 ? 001 22.jul.2015 rev.002 tsz02201-0j2j0a900710-1-2 operational notes 1. reverse connection of power supply connecting the power supply in reverse polarity can dam age the ic. take precautions against reverse polarity when connecting the power supply, such as mounting an external diode between the power supply and the ics power supply terminals. 2. power supply lines design the pcb layout pattern to provide low impedance supply lines. separate the ground and supply lines of the digital and analog blocks to prevent noise in the ground and supply li nes of the digital block from affecting the analog block. furthermore, connect a capacitor to ground at all power supply pins. consider the effect of temperature and aging on the capacitance value when using electrolytic capacitors. 3. ground voltage ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition. 4. ground wiring pattern when using both small-signal and large-current ground trac es, the two ground traces should be routed separately but connected to a single ground at the reference point of the application board to avoid fluct uations in the small-signal ground caused by large currents. also ensure that the ground traces of external components do not cause variations on the ground voltage. the ground lines must be as short and thick as possible to reduce line impedance. 5. thermal consideration should by any chance the power dissipation rating be exceeded, the rise in temperature of the chip may result in deterioration of the properties of the chip. the absolute maximum rating of the pd stated in this specification is when the ic is mounted on a 70mm x 70mm x 1.6mm glass epoxy board. in case of exceeding this absolute maximum rating, increase the board size and copper area to prevent exceeding the pd rating. 6. recommended operating conditions these conditions represent a range within which the expected characteristics of the ic c an be approximately obtained. the electrical characteristics are guaranteed under the conditions of each parameter. 7. inrush current when power is first supplied to the ic, it is possible that th e internal logic may be unstable and inrush current may flow instantaneously due to the internal powering sequence and del ays, especially if the ic has more than one power supply. therefore, give special consideration to power coupling capacitance, power wiring, width of ground wiring, and routing of connections. 8. operation under str ong electromagnetic field operating the ic in the presence of a strong electromagnetic field may cause the ic to malfunction. 9. testing on application boards when testing the ic on an application board, connecting a capa citor directly to a low-impedance output pin may subject the ic to stress. always discharge capacitors completely after each process or step. the ics power supply should always be turned off completely before connecting or removing it from the test setup during the inspection process. to prevent damage from static discharge, ground the ic duri ng assembly and use similar precautions during transport and storage. 10. inter-pin short and mounting errors ensure that the direction and position are correct when m ounting the ic on the pcb. inco rrect mounting may result in damaging the ic. avoid nearby pins being shorted to each other especially to ground, power supply and output pin. inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and unintentional solder bridge deposited in between pins during assembly to name a few. 11. unused input terminals input terminals of an ic are often connected to the gate of a mos transistor. the gate has extremely high impedance and extremely low capacitance. if left unconnected, the electr ic field from the outside can easily charge it. the small charge acquired in this way is enough to produce a significant effect on the conduction through the transistor and cause unexpected operation of the ic. so unless otherwise specified, unused input terminals should be connected to the power supply or ground line. downloaded from: http:///
13/18 datasheet d a t a s h e e t BD3539FVM bd3539nux ? 2014 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 ? 15 ? 001 22.jul.2015 rev.002 tsz02201-0j2j0a900710-1-2 operational notes C continued 12. regarding input pins of the ic this monolithic ic contains p+ isolat ion and p substrate layers between adjac ent elements in order to keep them isolated. p-n junctions are formed at the intersection of t he p layers with the n layers of other elements, creating a parasitic diode or transistor. for example (refer to figure below): when gnd > pin a and gnd > pin b, the p-n junction operates as a parasitic diode. when gnd > pin b, the p-n junction operates as a parasitic transistor. parasitic diodes inevitably occur in the structure of the ic . the operation of parasitic diodes can result in mutual interference among circuits, operational faults, or physical damage. therefore, conditions that c ause these diodes to operate, such as applying a voltage lower than the gnd voltage to an input pin (and thus to the p substrate) should be avoided. figure 10. example of monolithic ic structure 13. thermal shutdown circuit (tsd) this ic has a built-in thermal shutdown circuit that prev ents heat damage to the ic. normal operation should always be within the ics power dissipation rating. if however the rating is exceeded for a continued period, the junction temperature (tj) will rise which will activate the tsd circuit that will turn off all output pi ns. when the tj falls below the tsd threshold, the circuits are automatically restored to normal operation. note that the tsd circuit operates in a situation that exceeds the absolute maximum ratings and therefore, under no circumstances, should the tsd circuit be used in a set design or for any purpose other than protecting the ic from heat damage. the present ic incorporates a thermal shutdown protection circuit (tsd circuit). the working temperature is 175c (standard value) and has a -15c (standard value) hysteresis width. 14. capacitor across output and gnd if a large capacitor is connected between the output pin and gro und pin, current from the charged capacitor can flow into the output pin and may destroy the ic when the vcc or vtt_in pin is shorted to ground or pulled down to 0v. use a capacitor smaller than 1000f between output and ground. 15. output capacitor, resistor (c 1 /block diagram) do not fail to connect a output capacit or to vref output terminal for stabiliz ation of output volt age. the capacitor connected to vref output terminal works as a loop gain phase compensator. insufficient capacitance may cause oscillation. it is recommended to use a low temperature coefficient 1-10 f ceramic capacitor, though it depends on ambient temperature and load conditions. it is therefore re quested to carefully check under the actual temperature and load conditions to be applied. 16. output capacitor (c 4 ) do not fail to connect a capacitor to vtt output pin for stabilization of output voltage. this output capacitor works as a loop gain phase compensator and an output voltage variat ion reducer in the event of sudden change in load. insufficient capacitance may cause an oscillat ion. and if the equivalent series resistance (esr) of this capacitor is high, the variation in output voltage increases in the event of sudden change in load. it is recommended to use a 10 f or so ceramic capacitor, though it depends on ambient temperature and load conditions. it is therefore requested to carefully check under the actual temperature and load conditions to be applied. downloaded from: http:///
14/18 datasheet d a t a s h e e t BD3539FVM bd3539nux ? 2014 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 ? 15 ? 001 22.jul.2015 rev.002 tsz02201-0j2j0a900710-1-2 operational notes C continued 17. input capacitors setting (c 2 and c 3 ) these input capacitors are used to reduc e the output impedance of power supply to be connected to the input terminals (vcc and vtt_in). increase in the power supply output impedance may result in oscillation or degradation in ripple rejecting characteristics. it is recommended to use a low temperature coefficient 1 f (for vcc) and 10 f (for vtt_in) capacitor, but it depends on the characteristics of the power supply input, and the capacitance and impedance of the pc board wiring pattern. it is therefore requested to carefully c heck under the actual temperature and load conditions to be applied. 18. input terminals (vcc, vddq, vtt_in and en) vcc, vddq, vtt_in and en terminals of this ic are m ade up independent one another. to vcc terminal, the uvlo function is provided for malfunction prot ection. irrespective of t he input order of the inputs terminals, vtt output is activated to provide the output voltage when uvlo and en vo ltages reach the threshold voltage while vref output is activated when uvlo voltage reaches the threshold. if v ddq and vtt_in terminals have equal potential and common impedance, any change in current at vtt_in terminal may resu lt in variation of vtt_in voltage, which affects vddq terminal and may cause variation in the output voltage. it is therefore required to perform wiring in such manner that vddq and vtt_in terminals may not have common impedance. if impossible, take appropriate corrective measures including suitable cr filter to be inserted between vddq and vtt_in terminals. 19. vtts terminal this terminal is used to improve load regulation of vtt outpu t. the connection with vtt terminal must be done so that it would not have a common impedance with high current line for better load regulation of vtt output. 20. operating range within the operating range, the operation and function of the circuits are generally guaranteed at an ambient temperature within the range specified. the values specified for electrical c haracteristics may not be guaranteed, but drastic change may not occur to such characteristics within the operating range. 21. allowable loss pd for the allowable loss, the thermal der ating characteristics are shown on page 12, which should be used as a guide. any use that exceeds the allowable loss ma y result in degradation in the functions inherent to ic including a decrease in current capability due to chip temperatur e increase. use within the allowable loss. 22. the use of the ic in the strong electromagnetic field may sometimes cause malfunction, to which care must be taken. in the event that a load containing a large inductance component is connected to the output terminal, and generation of back-emf at the start-up and wh en output is turned off is assumed, it is recommended to insert a protection diode. 23. in the event that a load containi ng a large inductance component is connected to the output terminal, an d generation of back-emf at the start-up and when output is turned o ff is assumed, it is recommended to insert a protection diode. 24. application circuit although we can recommend the application circuits contained herein with a relatively high degree of confidence, we ask that you verify all characteristics and specifications of the circuit as well as its performance under actual conditions. please note that we c annot be held responsible for problems that may arise due to patent infringements or noncompliance with any and all applicable laws and regulations. output pin (example) downloaded from: http:///
15/18 datasheet d a t a s h e e t BD3539FVM bd3539nux ? 2014 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 ? 15 ? 001 22.jul.2015 rev.002 tsz02201-0j2j0a900710-1-2 ordering information b d 3 5 3 9 x x x t r part number package fvm: msop8 nux: vson008x2030 packaging and forming specification tr: embossed tape and reel marking diagrams part number marking package orderable part number 3539 msop8 BD3539FVM-tr 3539 vson008x2030 bd3539nux-tr msop8 (top view) 353 part number marking lot number 1pin mark 9 vson008x2030 (top view) 9 part number marking lot numbe r 1pin mark 353 downloaded from: http:///
16/18 datasheet d a t a s h e e t BD3539FVM bd3539nux ? 2014 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 ? 15 ? 001 22.jul.2015 rev.002 tsz02201-0j2j0a900710-1-2 physical dimension, tape and reel information package name msop8 direction of feed reel ? order quantity needs to be multiple of the minimum quantity. embossed carrier tape tapequantity direction of feed the direction is the 1pin of product is at the upper right when you hold reel on the left hand and you pull out the tape on the right hand 3000pcs tr () 1pin downloaded from: http:///
17/18 datasheet d a t a s h e e t BD3539FVM bd3539nux ? 2014 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 ? 15 ? 001 22.jul.2015 rev.002 tsz02201-0j2j0a900710-1-2 physical dimension, tape and reel information C continued package name vson008x2030 ? order quantity needs to be multiple of the minimum quantity. embossed carrier tape tapequantity direction of feed the direction is the 1pin of product is at the upper right when you hold reel on the left hand and you pull out the tape on the right hand 4000pcs tr () direction of feed reel 1pin downloaded from: http:///
18/18 datasheet d a t a s h e e t BD3539FVM bd3539nux ? 2014 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 ? 15 ? 001 22.jul.2015 rev.002 tsz02201-0j2j0a900710-1-2 revision history date revision changes 07.mar.2014 001 new release 22.jul.2015 002 revised applications downloaded from: http:///
datasheet d a t a s h e e t notice-pga-e rev.001 ? 2015 rohm co., ltd. all rights reserved. notice precaution on using rohm products 1. our products are designed and manufac tured for application in ordinary elec tronic equipments (such as av equipment, oa equipment, telecommunication equipment, home electroni c appliances, amusement equipment, etc.). if you intend to use our products in devices requiring ex tremely high reliability (such as medical equipment (note 1) , transport equipment, traffic equipment, aircraft/spacecra ft, nuclear power controllers, fuel c ontrollers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (specific applications), please consult with the rohm sale s representative in advance. unless otherwise agreed in writing by rohm in advance, rohm shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ro hms products for specific applications. (note1) medical equipment classification of the specific applications japan usa eu china class class class b class class ? class 2. rohm designs and manufactures its products subject to strict quality control system. however, semiconductor products can fail or malfunction at a certain rate. please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe desi gn against the physical injury, damage to any property, which a failure or malfunction of our products may cause. the following are examples of safety measures: [a] installation of protection circuits or other protective devices to improve system safety [b] installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. our products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditio ns, as exemplified below. accordin gly, rohm shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of an y rohms products under any special or extraordinary environments or conditions. if you intend to use our products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] use of our products in any types of liquid, incl uding water, oils, chemicals, and organic solvents [b] use of our products outdoors or in places where the products are exposed to direct sunlight or dust [c] use of our products in places where the products ar e exposed to sea wind or corrosive gases, including cl 2 , h 2 s, nh 3 , so 2 , and no 2 [d] use of our products in places where the products are exposed to static electricity or electromagnetic waves [e] use of our products in proximity to heat-producing components, plastic cords, or other flammable items [f] sealing or coating our products with resin or other coating materials [g] use of our products without cleaning residue of flux (ev en if you use no-clean type fluxes, cleaning residue of flux is recommended); or washing our products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] use of the products in places subject to dew condensation 4. the products are not subjec t to radiation-proof design. 5. please verify and confirm characteristics of the final or mounted products in using the products. 6. in particular, if a transient load (a large amount of load applied in a short per iod of time, such as pulse. is applied, confirmation of performance characteristics after on-boar d mounting is strongly recomm ended. avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading c ondition may negatively affect product performance and reliability. 7. de-rate power dissipation (pd) depending on ambient temper ature (ta). when used in seal ed area, confirm the actual ambient temperature. 8. confirm that operation temperat ure is within the specified range described in the product specification. 9. rohm shall not be in any way responsible or liable for fa ilure induced under deviant condi tion from what is defined in this document. precaution for mounting / circuit board design 1. when a highly active halogenous (chlori ne, bromine, etc.) flux is used, the resi due of flux may negatively affect product performance and reliability. 2. in principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must be used on a through hole mount products. if the flow sol dering method is preferred on a surface-mount products, please consult with the rohm representative in advance. for details, please refer to rohm mounting specification downloaded from: http:///
datasheet d a t a s h e e t notice-pga-e rev.001 ? 2015 rohm co., ltd. all rights reserved. precautions regarding application examples and external circuits 1. if change is made to the constant of an external circuit, pl ease allow a sufficient margin considering variations of the characteristics of the products and external components, including transient characteri stics, as well as static characteristics. 2. you agree that application notes, re ference designs, and associated data and in formation contained in this document are presented only as guidance for products use. theref ore, in case you use such information, you are solely responsible for it and you must exercise your own indepen dent verification and judgment in the use of such information contained in this document. rohm shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. precaution for electrostatic this product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. please take proper caution in your manufacturing process and storage so that voltage exceeding t he products maximum rating will not be applied to products. please take special care under dry condit ion (e.g. grounding of human body / equipment / solder iron, isolation from charged objects, se tting of ionizer, friction prevention and temperature / humidity control). precaution for storage / transportation 1. product performance and soldered connections may deteriora te if the products are stor ed in the places where: [a] the products are exposed to sea winds or corros ive gases, including cl2, h2s, nh3, so2, and no2 [b] the temperature or humidity exceeds those recommended by rohm [c] the products are exposed to di rect sunshine or condensation [d] the products are exposed to high electrostatic 2. even under rohm recommended storage c ondition, solderability of products out of recommended storage time period may be degraded. it is strongly recommended to confirm sol derability before using products of which storage time is exceeding the recommended storage time period. 3. store / transport cartons in the co rrect direction, which is indicated on a carton with a symbol. otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. use products within the specified time after opening a humidity barrier bag. baking is required before using products of which storage time is exceeding the recommended storage time period. precaution for product label qr code printed on rohm products label is for rohms internal use only. precaution for disposition when disposing products please dispose them proper ly using an authorized industry waste company. precaution for foreign exchange and foreign trade act since concerned goods might be fallen under listed items of export control prescribed by foreign exchange and foreign trade act, please consult with rohm in case of export. precaution regarding intellectual property rights 1. all information and data including but not limited to application example contained in this document is for reference only. rohm does not warrant that foregoi ng information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. 2. rohm shall not have any obligations where the claims, actions or demands arising from the co mbination of the products with other articles such as components, circuits, systems or external equipment (including software). 3. no license, expressly or implied, is granted hereby under any intellectual property rights or other rights of rohm or any third parties with respect to the products or the informati on contained in this document. pr ovided, however, that rohm will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to manufacture or sell products containing the produc ts, subject to the terms and conditions herein. other precaution 1. this document may not be reprinted or reproduced, in whol e or in part, without prior written consent of rohm. 2. the products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of rohm. 3. in no event shall you use in any wa y whatsoever the products and the related technical information contained in the products or this document for any military purposes, incl uding but not limited to, the development of mass-destruction weapons. 4. the proper names of companies or products described in this document are trademarks or registered trademarks of rohm, its affiliated companies or third parties. downloaded from: http:///
datasheet datasheet notice C we rev.001 ? 201 5 rohm co., ltd. all rights reserved. general precaution 1. before you use our pro ducts, you are requested to care fully read this document and fully understand its contents. rohm shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny rohms products against warning, caution or note contained in this document. 2. all information contained in this docume nt is current as of the issuing date and subj ec t to change without any prior notice. before purchasing or using rohms products, please confirm the la test information with a rohm sale s representative. 3. the information contained in this doc ument is provi ded on an as is basis and rohm does not warrant that all information contained in this document is accurate an d/or error-free. rohm shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. downloaded from: http:///

▲Up To Search▲

Price & Availability of BD3539FVM

	To Download BD3539FVM Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .