? 2016 littelfuse, inc. specifcations are subject to change without notice. revised: 08/22/16 the 2016l series ptc provides surface mount overcurrent protection for low voltage (60v) applications where resettable protection is desired. electrical characteristics part number marking i hold (a) i trip (a) v max (vdc) i max (a) p d typ. (w) maximum time to trip resistance agency approvals current (a) time (sec.) r min () r 1max () 2016l030 lf030 0.30 0.60 60 20 1.40 1. 5 3.0 0.500 2.300 x x 2016l050 lf050 0.55 1. 10 60 20 1.40 2.5 5.0 0.200 1.000 x x 2016l075/60 lf075-60 0.75 1.50 60 20 1.40 8.0 0.5 0.130 0.900 x x 2016l100 lf100 1. 10 2.20 15 40 1.40 8.0 0.5 0.100 0.400 x x 2016l100/33 lf100-33 1. 10 2.20 33 40 1.40 8.0 0.5 0.100 0.400 x x 2016l150 lf150 1.50 3.00 15 40 1.40 8.0 1. 0 0.070 0.180 x x 2016l150/33 lf150-33 1.50 3.00 33 40 2.0 8.00 1. 0 0 0.070 0.180 2016l200 lf200 2.00 4.20 6 40 1.40 8.0 3.0 0.048 0.100 x x 2016l260/24 lf260-24 2.60 5.00 24 40 1. 6 8.00 5.00 0.025 0.075 2016l300/16 lf0300 3.00 5.00 16 40 1. 6 8.00 10.00 0.015 0.048 2016l500 lf500 5.00 10.00 6 100 2.0 25.00 2.00 0.005 0.025 x i hold = hold current: maximum current device will pass without tripping in 20c still air. i trip = trip current: minimum current at which the device will trip in 20c still air. v max = maximum voltage device can withstand without damage at rated current (i max) i max = maximum fault current device can withstand without damage at rated voltage (v max ) p d = power dissipated from device when in the tripped state at 20c still air. r min = minimum resistance of device in initial (un-soldered) state. r typ = typical resistance of device in initial (un-soldered) state. r 1max = maximum resistance of device at 20c measured one hour after tripping or refow soldering of 260c for 20 sec. caution: operation beyond the specifed rating may result in damage and possible arcing and fame. * agency approval is pending description features applications ? rohs compliant, lead-free and halogen-free ? fast response to fault currents ? high voltage ? low-profle ? ieee 1394 port protection ? powered ethernet port protection (ieee 802.3 af) ? automotive electronic control module protection ? low voltage telecom equipment protection agency approvals 2016l series r ohs warning ? users shall independently assess the suitability of these devices for each of their applications ? operation of these devices beyond the stated maximum ratings could result in damage to the devices and lead to electrical arcing and/or fre ? these devices are intended to protect against the effects of temporary over-current or over-temperature conditions and are not intended to perform as protective devices where such conditions are expected to be repetitive or prolonged in duration ? exposure to silicon-based oils, solvents, electrolytes, acids, and similar materials can adversely affect the performance of these pptc devices ? these devices undergo thermal expansion under fault conditions, and thus shall be provided with adequate space and be protected against mechanical stresses ? circuits with inductance may generate a voltage (l di/dt) above the rated voltage of the pptc device. agency agency file number e183209 r50119118 poly-fuse ? resettable ptcs surface mount > 2016l series
? 2016 littelfuse, inc. specifcations are subject to change without notice. revised: 08/22/16 ambient operation temperature -40c -20c 0c 20c 40c 50c 60c 70c 85c part number hold current (a) 2016l030 0.45 0.40 0.35 0.30 0.25 0.23 0.20 0.18 0.14 2016l050 0.93 0.80 0.65 0.50 0.42 0.38 0.33 0.30 0.23 2016l075/60 1.21 1.06 0.91 0.75 0.61 0.54 0.45 0.38 0.26 2016l100 1.66 1.47 1.29 1. 10 0.91 0.83 0.73 0.64 0.50 2016l100/33 1.66 1.47 1.29 1. 10 0.91 0.83 0.73 0.64 0.50 2016l150 2.26 2.00 1. 76 1.50 1.24 1. 13 1. 0 0 0.87 0.68 2016l150/33 2.25 2.05 1.79 1.50 1.31 1. 17 1.05 0.93 0.72 2016l200 2.80 2.50 2.19 2.00 1.84 1. 74 1.50 1.34 1. 14 2016l260/24 3.80 3.43 3.04 2.60 2.24 2.03 1.82 1.64 1.25 2016l300/16 4.32 3.93 3.57 3.00 2.58 2.40 2.22 1.89 1.68 2016l500 7.20 6.55 5.95 5.00 4.30 4.00 3.70 3.15 2.80 temperature rerating temperature rerating curve average time current curves the average time current curves and temperature rerating curve performance is affected by a number or variables, and these curves provided as guidance only. customer must verify the performance in their application. note: typical temperature rerating curve, refer to table for derating data -40 -30 -20 -1 00 10 20 30 40 50 60 70 80 85 10 % 30% 50% 70% 90% 11 0% 1 30% 1 50% 1 70% t emperature (c) percentage of rated current 0.0 1 0.1 1 10 10 0 0.1 11 0 time in seconds cur r ent in amper es 0.30a 0.50a 0.75a/60 1. 00 a 1. 0 0a/3 3 1 .50a 2.0 0a 1 .50a/33 2.60a/24 3.0 0a/1 6 5.0 0a additional information datasheet samples reses samples poly-fuse ? resettable ptcs surface mount > 2016l series
? 2016 littelfuse, inc. specifcations are subject to change without notice. revised: 08/22/16 environmental specifcations soldering parameters operating/storage temperature -40c to +85c maximum device surface temperature in tripped state 125c passive aging +85c, 1000 hours -/+5% typical resistance change humidity aging +85c, 85%,r.h.,1000 hours -/+5% typical resistance change thermal shock milCstdC202, method 107 +85c/-40c 20 times -30% typical resistance change solvent resistance milCstdC202, method 215 no change vibration milCstdC883, method 2007, condition a no change moisture sensitivity level level 1, jCstdC020 physical specifcations terminal material solder-plated copper (solder material: matte tin(sn)) lead solderability meets eia specifcation rs186-9e, ansi/ j-std-002 category 3. ti me te mperature t p t l t s(max) t s(min) 25 t p t l t s time to peak temperature preheat p reheat ramp-up r amp-up ramp-down r amp-d o critical zone t l to t p profle feature pb-free assembly average ramp-up rate (t s(max) to t p ) 3c/second max pre heat: temperature min (t s(min) ) 150c temperature max (t s(max) ) 200c time (min to max) (t s ) 60 C 180 secs time maintained above: temperature (t l ) 217c temperature (t l ) 60 C 150 seconds peak / classifcation temperature (t p ) 260 +0/-5 c time within 5c of actual peak temperature (t p ) 20 C 40 seconds ramp-down rate 6c/second max time 25c to peak temperature (t p ) 8 minutes max. -- all temperature refer to topside of the package, measured on the package body surface -- if refow temperature exceeds the recommended profle, devices may not meet the performance requirements -- recommended refow methods: ir, vapor phase oven, hot air oven, n 2 environment for lead -- recommended maximum paste thickness is 0.25mm (0.010 inch) -- devices can be cleaned using standard industry methods and solvents -- devices can be reworked using the standard industry practices poly-fuse ? resettable ptcs surface mount > 2016l series
? 2016 littelfuse, inc. specifcations are subject to change without notice. revised: 08/22/16 part ordering number system pa ckaging st yle l: littelfuse surface mount pptc quantity code: d=1500 m=1000 p=2000 r: tape & reel 2016 l xxx /xx d r series device size code (0.20 x 0.16 inch) i hold hold current code (refer to electrical characteristics table) special voltage rating item (not applicable to all parts. refer to electrical characteristics table for additional information) -a: automotive grade blank: standard version - a packaging dimensions (mm) c to p vie w pa d layout side vie w bo t tom vie w 4.60 mm (.1 81?) 3.40 mm (.1 33?) 1 .50 mm (.059?) d marking code v aries wi th ampera ge and vo lt a ge ra ting see electrical chara cteris tics char t sh o wn are: - 1 .1a/1 5v ra ting (left) - 1 .1a/33v ra ting (righ t) e a b 10 0 10 0 10 0 -33 part number a b c d e inches mm inches mm inches mm inches mm inches mm min max min max min max min max min max min max min max min max min max min max 2016l030 0.19 0.21 4.72 5.44 0.15 0.17 3.7 4.43 0.03 0.05 0.75 1.25 0.01 0.06 0.3 1. 5 0.01 0.03 0.25 0.65 2016l050 0.05 0.08 1.20 2.00 2016l075/60 0.05 0.08 1.20 2.00 2016l100 0.02 0.03 0.50 0.75 2016l100/33 0.03 0.05 0.75 1.25 2016l150 0.03 0.06 0.75 1.55 2016l150/33 4.43 0.03 0.06 0.80 1.60 2016l200 4.43 0.02 0.03 0.50 0.75 2016l260/24 4.43 0.03 0.06 0.80 1.60 2016l300/16 2016l500 part number ordering number halogen free i hold (a) i hold code voltage option packaging option quantity quantity & packaging codes 2016l030 2016l030dr ye s 0.30 030 tape and reel 1500 dr 2016l050 2016l050mr ye s 0.55 050 tape and reel 1000 mr 2016l075/060 2016l075/60mr ye s 0.75 075 /60 tape and reel 1000 mr 2016l100 2016l100pr ye s 1. 10 110 tape and reel 2000 pr 2016l100/33 2016l100/33dr ye s 1. 10 110 /33 tape and reel 1500 dr 2016l150 2016l150dr ye s 1.50 150 tape and reel 1500 dr 2016l150/33 2016l150/33dr ye s 1.50 150 /33 tape and reel 1,500 dr 2016l200 2016l200pr ye s 2.00 200 tape and reel 2000 pr 2016l260/24 2016l260/24dr ye s 2.60 260 /24 tape and reel 1,500 dr 2016l300/16 2016l300/16dr ye s 3.00 300 /16 tape and reel 1,500 dr 2016l500 2016l500dr ye s 5.00 500 /6 tape and reel 1,500 dr poly-fuse ? resettable ptcs surface mount > 2016l series
? 2016 littelfuse, inc. specifcations are subject to change without notice. revised: 08/22/16 tape specifications: eia-481-1 (mm) reel dimensions: eia-481-1 (mm) 2016l100 2016l200 2016l030 2016l100/33 2016l150 2016l150/33 2016l260/24 2016l300/16 2016l500 2016l050 2016l075/60 w 12.0+/- 0.30 12.0+/- 0.30 12.0+/- 0.30 c ?178.0+/-1.0 f 5.50+/- 0.05 5.50+/- 0.05 5.50+/- 0.05 d ?60.2+/-0.5 e 1 1.75+/- 0.10 1.75+/- 0.10 1.75+/- 0.10 h 16.0+/- 0.5 d 0 1.55+/- 0.05 1.55+/- 0.05 1.55+/- 0.05 w 13.2+/- 1.5 d 1 1.50 (min) 1.50 (min) 1.50 (min) p 0 4.0+/- 0.10 4.0+/- 0.10 4.0+/- 0.10 p 1 8.0+/- 0.10 8.0+/- 0.10 8.0+/- 0.10 p 2 2.0+/- 0.05 2.0+/- 0.05 2.0+/- 0.05 a 0 4.40+/- 0.10 4.48+/- 0.10 4.45+/- 0.10 b 0 5.50+/- 0.10 5.40+/- 0.10 5.48+/- 0.10 t 0.25+/- 0.10 0.25+/- 0.10 0.25+/- 0.10 k o 0.80+/- 0.10 1.36+/- 0.10 1.86+/- 0.10 leader min. 390 390 390 trailer min. 160 160 160 tape and reel specifcations tape and reel diagram w c d h d 1 k 0 b 0 d 1 t f w e 1 p 2 d 0 p 0 p 1 poly-fuse ? resettable ptcs surface mount > 2016l series
|
