www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 1 of 8 s pec n o : ? ? s s p p e e c c i i f f i i c c a a t t i i o o n n customer product ? saw filter model no hdf 1086 a1 smd - 7 m arking ? hdf7g191 prepared checked approv ed ? d a t e 2007 - 5 - 21 ??? shoulder electronics limited ?? c ustomer received: c hecked ? approved d ate
saw filter hdf 1086a1 s - 7 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 2 of 8 ?? history record date spec . no . ?? part no . ??? customer no . mo dify content ? remark
saw filter hdf 1086a1 s - 7 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 3 of 8 1. scope this specification shall cover the characteristics of saw filter with f1086a 1 s 7 used digital television 2 . electrical specification dc voltage vdc> 0v operation temperature - 40c~+85c storage temperature - 40c~+85c rf power dissipation 0 dbm(source impedance 200) electronic characteristics 2 - 1.typical frequency response
saw filter hdf 1086a1 s - 7 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 4 of 8 2 - 2.electrical characteris tics p art number min typ max unit nominal frequency - 1086.0 - mhz maximum insertion attenuation 1081~1091mhz - 2.2 2.8 db amplitude ripple in passband 1081~1091mhz - 0.6 1.0 db amplitude ripple in any 6mhz band 1081~1091mhz - 0.5 0.8 db a ttenuation 500~988mhz 988~1002mhz 1038~1046mhz 1140~1600mhz 2040~2128mhz 60 60 35 55 50 64 63 37 60 57 - - - - - db 3. test circuit 4. dimension
saw filter hdf 1086a1 s - 7 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 5 of 8 marking hdf 7g191 hd: brand f : filter 7 : smd - 7 g191 : no. 5. environmental characteristics 5 - 1 temperature cycling subject the device to a low temperature of - 45 for 30 minutes. following by a high temperature of +25 for 5 minutes and a higher temperatur e of +85 for 30 minutes. then release the device into the room conditions for 1 to 2 hours prior to the me a surement. it shall meet the specifications in 2 - 2 . 5 - 2 resistance to solder heat submerge the device terminals into the solder bath at 260 5 f or 10 1 sec. then release the device into the room conditions for 4 hours. it shall meet the specifications in 2 - 2 . 5 - 3 solderability submerge the device terminals into the solder bath at 245 5 for 5s, more than 95% area of the soldering pad must be covered with new solder. it shall meet the specifications in 2 - 2 . 5 - 4 mechanical shock drop the device randomly onto the concrete floor from the height of 1 m 3 times. the filter shall fulfill the specifications in 2 - 2 . 5 - 5 vibration subje ct the device to the vibration for 2 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 hz. the filter shall fulfill the specifications in 2 - 2 . 6. remark 6.1 static voltage static voltage between signal load & ground may cause det e rioration &destruction of the component. please avoid static voltage. 6.2 ultrasonic cleaning ultrasonic vibration may cause det e ri oration & destruction of the component. please avoid ultraso nic cleaning 6.3 soldering only leads of component may be soldered. please avoid soldering another part of component.
saw filter hdf 1086a1 s - 7 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 6 of 8 7 . packing 7 .1 dimensions (1) carrier tape: figure 1 (2) reel: figure 2 (3) the product shall be packed properly not to be damaged during transportation and storage. 7 .2 reeling quantity 1000 pcs/reel 7?? 3000 pcs/reel 13?? 7 .3 taping structure (1) the tape shall be wound around the reel in the direction shown below. (2) label device name user product name quantity lot no. (3) leader part and vacant position specifications.
saw filter hdf 1086a1 s - 7 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 7 of 8 8 . tape specifications 8 .1 tensile strength of carrier tape: 4.4n/mm width 8 .2 top cover tape adhesion (see the below figure) (1) pull off angle: 0~15 o (2) speed: 300mm/min. (3) force: 20~70g [figure 1] carrier tape dimensions [unit:mm] w f e p0 p1 p2 d0 d1 t1 t2 a b 12.00 0.30 5.50 0.10 1.75 0.10 4.00 0.10 4.00 0.10 2.00 0.10 ?1.50 ? 1.5 0.25 0.31 0.05 1.30 0.10 3.4 max. 3.4 max [fi gure 2]
saw filter hdf 1086a1 s - 7 www.shoulder.cn tel:0755 - 82916880 fax:0755 - 82916881 e - mail: info@shoulder.cn page 8 of 8 [unit:mm] a b c d e w t r ? 330 1.0 ? 100 0.5 ? 13 0.5 ? 21 0.8 2 0.5 13 0.3 3 max. 1.0 max.
|
