telefon: +49 (0) 6135 7026 -0 telefax: +49 (0) 6135 931070 www.peak-electronics.de info@peak-electronics.de ppm-series ppm03-s-xxelf 3 w ac/dc con verter single output input specifications input voltage range 85- 264 vac, 110- 370 vdc input frequency 47- 440 hz input current 110 vac 230 vac 65ma , typ. 30ma , typ. inrush current 110 vac 230 vac 10a, typ. 20a, typ. external input fuse(recommended) ppm03-s-xxelf 0.5a/250v slow blow output specifications voltage set accuracy 2% , ty p. ( 3% at 3.3 vout) input variation 0.5%, typ. load variation (10-100%) single output mode ls 1%, typ. ripple& noise (p-p) 20mhz bandwidt h 30mv, typ. short circuit protection continuous, and auto resume over temperature protection 150c, max. over output voltage protection chip lock up general specifications temperature ranges operating : power derating above 55c: storage: case temperature: -25c to +70c 2% / c -40c to +105c +95c max weight ~ 25g hold-up time (vin=230vac) 50m s(typ.) humidity (non condensing) 95%(max) temperature coefficient 0.02% /c switching frequency 100khz, typ. efficiency see table i/o-isolation voltage 3000 vac / 1min leakage current none case material ul 94v-0 rated install pcb mtbf >200,000h @25c rohs compliant soldering 260c / max. 10 sec. examples of partnumbers/modelcode part no. power (watt) output (volt) ripple and noise (typ..) efficiency (% min.) ppm03-s-3.3elf 2.3 3.3v / 700ma 30mv 63 ppm03-s-05elf 3 5v / 600ma 30mv 72 PPM03-S-09ELF 3 9v / 330ma 30mv 74 ppm03-s-12elf 3 12v / 250ma 30mv 76 ppm03-s-15elf 3 15v / 200ma 30mv 76 ppm03-s-24elf 3 24v / 125ma 30mv 78 other specifications please enquire.
ppm-series ppm03-s-xxelf 3 w ac/dc con verter single output dimensions / pinning 17.78 (0.70) 23.00 (0.91) 0.8 (0.03) # single out 1 ac (l) 3 ac (n) 13 no connection 14 - v output 16 +v output 22 +vin (dc) 26 - vin (dc) pinning ppm03-s-xxelf temperaturederatinggraph ambienttemperaturec 100% 25 0 100 55 output 70
ppm-series ppm03-s-xxelf 3 w ac/dc con verter single output app notes measure typical applications ppm-series external typical value model c1 c2 c3 tvs ppm03-s-3.3elf 150 0.1 4.7/400v p4ke6.8a ppm03-s-05elf 150 0.1 4.7/400v p4ke6.8a PPM03-S-09ELF 120 0.1 4.7/400v p4ke12a ppm03-s-12elf 120 0.1 4.7/400v p4ke20a ppm03-s-15elf 120 0.1 4.7/400v p4ke20a ppm03-s-24elf 68 0.1 4.7/400v p4ke30a note 1. output filtering capacitors c1, c3 is electrolyt ic capacitors, it is recommended to use high freque ncy and low impedance electrolytic capacitors. for capacita nce and current of capacitor please refer to manufa cture?s datasheet. voltage derating of capacitor should be 80% or above. c2 is ceramic capacitor, it is used t o filter high frequency noise. tvs is a recommended componen t to protect post-circuits (when converter fails). 2. mov is required to ppm03 models, model: 471kd05, it is used to protect the device under surge. 3. it is recommended to connect fuse, the parameter for ppm03 models is 0.5a/250v slow blow. external input ntc is recommended to use 5d-14 or 10 /2w wire-round resistor. 4. if emc performance is required, recommended to a dd ?emc filter? at the input end c6:x capacitor, recommended parameter 0.1uf/275v; c7,c8:y capacitor , recommended parameter 220pf/2000v; nf: common model choke, recommended inductance is a bout 10mh-30mh. 5. ppm03 models: terminals 22 and 26 are internal r ectification and filtering terminals. to protect th e models further, it is recommended to connect an electrolyt ic capacitor c3 (it is recommended to be 4.7uf/400v ). if operation voltage of the module is between 160~264v ac, c3 can be removed. specification can be changed without notice. copyright peak electronics gmbhcs rev nov.08
|
