transient voltage suppressors smbj series speci?cations are subject to change without notice. please refer to http://www.ruilon.com for current information. electronic s circuit prote ct io n system
page:1 speci?cations are subject to change without notice. please refer to http://www.ruilon.com for current information. transient voltage suppressors - smbj series features mechanical characteristics rating symbol value units peak pulse power dissipation by 10x1000s test waveform (fig.1)(note 1) p ppm 600 watts steady state power dissipation on ini? nite heat sink at tl=75oc (fig. 5) p d 5 watts peak forward surge current, 8.3ms single half sine wave unidirectional only (note 2) i fsm 100 amps maximum instantaneous forward voltage at 25a for unidirectional only (note 3) v f 3.5/5.0 v operating junction and storage temperature range. t j , t stg -55c to 150c c typical thermal resistance junction to lead r ujl 20 c/w typical thermal resistance junction to ambient r uja 100 c/w notes: 1. non-repetitive current pulse , per fig. 3 and derated above ta = 25c per fig. 2. 2. mounted on copper pad area of 0.2x0.2 (5.0 x 5.0mm) to each terminal. 3. measured on 8.3ms single half sine wave or equivalent square wave for unidirectional device only, duty cycle=4 per minute maximum. 4. vf<3.5v for vbr < 200v and vf<5.0v for vbr > 201v. 1. halogen-free 2. rohs compliant 3. typical maximum temperature coef ?cient 4. v br = 0.1% xv br @25c x t 5. glass passivated chip junction in do-214aa package 6. 600w peak pulse capadility at 101000s waveform, repetition rate(duty cycles):0.01% 7. fast response time:typically less than 1.0ps from 0 volts to bv min 8. excellent clamping capability 9. low incremental surge resistance 10. typical ir less than 5a above 12v 11. high temperature soldering guaranteed: 260c/40 seconds / 0.375,(9.5mm) lead length, 5lbs., (2.3kg) tension 12. plastic package has underwriters laboratory fammability classi?cation 94v-0 tvs devices are ideal for the protection of i/o interfaces,vcc bus and other vulnerable circuits used in telecom, computer , industrial and consumer electronic applications. uni bi uni bi anode cathode applications circuit prote ct io n system
transient voltage suppressors - smbj series page:2 speci?cations are subject to change without notice. please refer to http://www.ruilon.com for current information. electriacl characteristics type number device marking code reverse stand-off voltage breakdown voltage@i t test current maximum clamping voltage@i pp peak pulse current reverse leakage @v rwm (uni) (bi) uni bi v rwm (v) v br min. (v) v br max. (v) i t (ma) v c (v) i pp (a) ir(a) smbj3.3a smbj3.3ca kc * 3.3 4.10 4.60 1 7.3 50.0 200 smbj5.0a smbj5.0ca ke ae 5.0 6.40 7.25 10 9.2 65.2 800 smbj6.0a smbj6.0ca kg ag 6.0 6.67 7.67 10 10.3 58.3 800 smbj6.5a smbj6.5ca kk ak 6.5 7.22 8.30 10 11.2 53.6 500 smbj7.0a smbj7.0ca km am 7.0 7.78 8.95 10 12.0 50.0 200 smbj7.5a smbj7.5ca kp ap 7.5 8.33 9.58 1 12.9 46.6 100 smbj8.0a smbj8.0ca kr ar 8.0 8.89 10.23 1 13.6 44.1 50 smbj8.5a smbj8.5ca kt at 8.5 9.44 10.82 1 14.4 41.7 20 smbj9.0a smbj9.0ca kv av 9.0 10.00 11.50 1 15.4 39.0 10 smbj10a smbj10ca kx ax 10.0 11.10 12.80 1 17.0 35.3 5.0 smbj11a smbj11ca kz az 11.0 12.20 14.00 1 18.2 33.0 5.0 smbj12a smbj12ca le be 12.0 13.30 15.30 1 19.9 30.2 5.0 smbj13a smbj13ca lg bg 13.0 14.40 16.50 1 21.5 27.9 5.0 smbj14a smbj14ca lk bk 14.0 15.60 17.90 1 23.2 25.8 5.0 smbj15a smbj15ca lm bm 15.0 16.70 19.20 1 24.4 24.6 5.0 smbj16a smbj16ca lp bp 16.0 17.80 20.50 1 26.0 23.1 5.0 smbj17a smbj17ca lr br 17.0 18.90 21.70 1 27.6 21.7 5.0 smbj18a smbj18ca lt bt 18.0 20.00 23.30 1 29.2 20.5 5.0 smbj20a smbj20ca lv bv 20.0 22.20 25.50 1 32.4 18.5 5.0 smbj22a smbj22ca lx bx 22.0 24.40 28.00 1 35.5 16.9 5.0 smbj24a smbj24ca lz bz 24.0 26.70 30.70 1 38.9 15.2 5.0 smbj26a smbj26ca me ce 26.0 28.90 33.20 1 42.1 14.2 5.0 smbj28a smbj28ca mg cg 28.0 31.10 35.80 1 45.4 13.2 5.0 smbj30a smbj30ca mk ck 30.0 33.30 38.30 1 48.4 12.4 5.0 smbj33a smbj33ca mm cm 33.0 36.70 42.20 1 53.3 11.3 5.0 smbj36a smbj36ca mp cp 36.0 40.00 46.00 1 58.1 10.3 5.0 smbj40a smbj40ca mr cr 40.0 44.40 51.10 1 64.5 9.3 5.0 smbj43a smbj43ca mt ct 43.0 47.80 54.90 1 69.4 8.6 5.0 smbj45a smbj45ca mv cv 45.0 50.00 57.50 1 72.7 8.3 5.0 smbj48a smbj48ca mx cx 48.0 53.30 61.30 1 77.4 7.7 5.0 smbj51a smbj51ca mz cz 51.0 56.70 65.20 1 82.4 7.3 5.0 smbj54a smbj54ca ne de 54.0 60.00 69.00 1 87.1 6.9 5.0 smbj58a smbj58ca ng dg 58.0 64.40 74.10 1 93.6 6.4 5.0 smbj60a smbj60ca nk dk 60.0 66.70 76.70 1 96.8 6.2 5.0 smbj64a smbj64ca nm dm 64.0 71.10 81.80 1 103.0 5.8 5.0 smbj70a smbj70ca np dp 70.0 77.80 89.50 1 113.0 5.3 5.0 smbj75a smbj75ca nr dr 75.0 83.30 95.80 1 121.0 4.9 5.0 smbj78a smbj78ca nt dt 78.0 86.70 99.70 1 126.0 4.7 5.0 smbj85a smbj85ca nv dv 85.0 94.40 108.20 1 137.0 4.4 5.0 smbj90a smbj90ca nx dx 90.0 100.00 115.50 1 146.0 4.1 5.0 smbj100a smbj100ca nz dz 100.0 111.00 128.00 1 162.0 3.7 5.0 smbj110a smbj110ca pe ee 110.0 122.00 140.50 1 177.0 3.4 5.0 smbj120a smbj120ca pg eg 120.0 133.00 153.00 1 193.0 3.1 5.0 smbj130a smbj130ca pk ek 130.0 144.00 165.50 1 209.0 2.9 5.0 smbj150a smbj150ca pm em 150.0 167.00 192.60 1 243.0 2.5 5.0 smbj160a smbj160ca pp ep 160.0 178.00 197.00 1 259.0 2.3 5.0 smbj170a smbj170ca pr er 170.0 189.00 209.00 1 275.0 2.2 5.0 smbj180a smbj180ca pt et 180.0 201.00 222.00 1 292.0 2.1 5.0 SMBJ190A smbj190ca pv ev 190.0 209.00 243.20 1 308.0 2.0 5.0 smbj200a smbj200ca px ex 200.0 220.00 247.00 1 324.0 1.9 5.0 smbj210a smbj210ca pz ez 210.0 231.00 268.80 1 340.0 1.8 5.0 smbj220a smbj220ca qe fe 220.0 242.00 281.60 1 356.0 1.7 5.0 smbj250a smbj250ca qg fg 250.0 279.00 309.00 1 405.0 1.5 5.0 smbj300a smbj300ca qk fk 300.0 335.00 371.00 1 486.0 1.3 5.0 circuit prote ct io n system
page:3 speci?cations are subject to change without notice. please refer to http://www.ruilon.com for current information. transient voltage suppressors - smbj series ratings and characteristic curves figure 2 - pulse der ating cur ve figure 3 - pulse w av ef or m figure 4 - t ypical junction capacitanc e figure 5 - st eady stat e po we r der ating cur ve a 0. 1 1 10 10 0 0. 00000 10 . 0000 10 . 000 10 .0 01 t d -pulse width (sec.) 0.2x0.2" (5.0x5.0mm) copper pad area p ppm -peak pulse power (kw) i pp m - p eak p ulse curr ent, % i rsm 0 0 50 10 0 15 0 1. 02 .0 3. 04 .0 t r =1 0sec p eak v alue i pp m i pp m 2 t j =25c as the point where the peak curr ent decays to 5 0% of i pp m 10 /1 00 0sec. w avefor m t d t-ti me (ms) half v alue i pp m ( ) 0 20 40 60 80 10 0 02 55 07 51 00 12 51 50 17 5 peak pulse power (p pp ) or current (i pp ) derating in percentage % t a - a mbient t emperature (oc) 1 10 10 0 1000 1000 0 1. 01 0. 0 100 .0 1000 .0 cj ( pf ) tj =2 5c f= 1.0m hz vs ig =5 0m vp -p un i- di re ct i ona l v= 0v bi -d ir ec ti ona l v= 0v v br - reverse breakdown vo ltage (v ) uni-directional @ v r bi-directional @ v r 0 1 2 3 4 5 6 02 55 07 51 00 12 51 50 17 5 p m(av ) , steady state power dissipatio n (w ) t a - ambient t emperature (oc) figure 1 - p eak pulse p owe r ratin g 0 20 40 60 80 10 0 12 0 0 0 1 0 1 1 nu mb er o f c ycl es a t 60 hz i fsm - peak forward surge current (a ) figure 6 - maximum non-repetiti ve p eak fo rw ar d surg e curr ent uni-dir ectional onl y circuit prote ct io n system
transient voltage suppressors - smbj series page:4 speci?cations are subject to change without notice. please refer to http://www.ruilon.com for current information. soldering parameters fefow condition lead-free assembly pre heat - temperature min (t s(min) ) 150c - temperature max (t s(min) ) 200c - time (min to max) (t s ) 60-180 secs average ramp up rate (liquidus temp (t l ) to peak 3c/second max t s(max) to t l - ramp-up rate 3c/second max refow - temperature (t l ) (liquidus) 217c - time (min to max) (t s ) 60-150 seconds peak temperature (t p ) 260 +0/-5 c time within 5c of actual peak temperature (t p ) 20-40 seconds ramp-down rate 6c/second max time 25c to peak temperature (t p ) 8 minutes max. do not exceed 280c physical specifcations weight 0.003 ounce, 0.093 grams case jedec do214aa. molded plastic body over glass passivated junction polarity color band denotes cathode except bidirectional. termina matte tin-plated leads, solderable per jesd22-b102d environmental specifcations temperature cycle jesd22-a104 pressure cooker jesd 22-a102 high temp. storage jesd22-a103 htrb jesd22-a108 thermal shock jesd22-a106 circuit prote ct io n system
page:5 speci?cations are subject to change without notice. please refer to http://www.ruilon.com for current information. transient voltage suppressors - smbj series dimensions dim inches millimeters min max min max a 0.077 0.086 1.950 2.200 b 0.160 0.180 4.060 4.570 c 0.130 0.155 3.300 3.940 d 0.084 0.096 2.130 2.440 e 0.030 0.060 0.760 1.520 f - 0.008 - 0.203 g 0.205 0.220 5.210 5.590 h 0.006 0.012 0.152 0.305 i 0.089 - 2.260 - j 0.085 - 2.160 - k - 0.107 - 2.740 l 0.085 - 2.160 - unit:mm part numbering system vo lt ag e bi-directional 5% v ol ta ge t olerance series xx xc a smbj packaging part number component package quantity packaging option packaging speci?cation smbjxxxxx do-214aa 500 tape & reel eia std rs-481 circuit prote ct io n system
page:6 speci?cations are subject to change without notice. please refer to http://www.ruilon.com for current information. ruilongyuan electronics co., ltd. reproducing and modifying information of the document is prohibited without permission from ruilongyuan international inc. ruilongyuan international inc. reserves the rights to make changes of the content herein the document anytime without noti?cation. please refer to our website for the latest document. ruilongyuan international inc. disclaims any and all liability arising out of the application or use of any product including damages incidentally and consequentially occurred. ruilongyuan international inc. does not assume any and all implied warranties, including warranties of ?tness for particular purpose, non-infringement and merchantability. applications shown on the herein document are examples of standard use and operation. customers are responsible in comprehending the suitable use in particular applications.ruilongyuan international inc. makes no representation or warranty that such applications will be suitable for the specifed use without further testing or modifcation. the products shown herein are not designed and authorized for equipments requiring high level of reliability or relating to human life and for any applications concerning life-saving or life-sustaining, such as medical instruments, transportation equipment,aerospace machinery et cetera. customers using or selling these products for use in such applications do so at their own risk and agree to fullyindemnify ruilongyuan international inc. for any damages resulting from such improper use or sale. tel: +86-755-8290 8296 fax: +86-755-8290 8002 e-mail: jack@ruilon.com circuit prote ct io n system
|
