specification part no. : mt 1 8 < a .0mm round led lamp observe precaution for handling electro static sensitive devices attention 3northway lane north latham,new york 12110. tollfree:1.800.984.5337 phone:1.518.956.2980 fax:1.518.785.4725 http://www.marktechopto.com
MT3301N-UY-A 3.0 mm round led lamp ver.: 01 date: 2013/08/02 page: 1 / description this amber lamp is made with algainp chip and water clear epoxy resin. ak 3.0 1.0max. notes: 1. all dimensions are in mm. 2. tolerance is 0.25mm unless otherwise noted. description led chip part no. material emitting color lens color MT3301N-UY-A algainp amber w ater clear
ver.: 01 date: 2013/08/02 page: 2 / absolute maximum ratings at ta=25 parameter symbol rating unit power dissipation p d 75 mw reverse voltage v r 5 v d.c. forward current if 30 ma reverse (leakage) current ir 100 a peak current(1/10duty cycle,0.1ms pulse width.) if(peak) 100 ma operating temperature range topr. -25 to +85 storage temperature range tstg. -40 to +100 soldering temperature(1.6mm from body) tsol. dip soldering : 260 for
5 sec. hand soldering : 350 for 3 sec.
electrostatic discharge esd. 6000 v electrical and optical characteristics: parameter symbol condition min. typ. max. unit luminous intensity i v if=20ma 3000 7000 mcd forward voltage vf if=20ma 2.1 2.5 v peak wavelength p if=20ma 591 nm dominant wavelength d if=20ma 587 596 nm reverse (leakage) current ir vr=5v 100 a viewing angle 21/2 if=20ma 30 deg spectrum line halfwidth ? if=20ma 15 nm notes:1. the datas tested by is tester. 2. customer?s special requirements are also welcome. MT3301N-UY-A 3.0 mm round led lamp
ver.: 01 date: 2013/08/02 page: 3 / typical electrical / optica l characteristics curves : applied voltage (v) forward current vs.applied voltage forward current if(ma) 10 20 40 30 50 1.2 1.6 2.0 2.4 2.8 3.0 forward current (ma) forward current vs. luminous intensity temperature(c) forward current vs. ambient temperature 0 204060 100 80 forward current if(ma) 10 20 40 30 50 radiation diagram 80 90 60 70 50 30 40 0.1 0.5 0.7 0.8 0.3 1.0 0.9 0.4 0.2 0.6 0 10 20 0.0 10.0 20.0 30.0 2000 4000 relative luminous intensity 6000 8000 10000 MT3301N-UY-A 3.0 mm round led lamp
ver.: 01 date: 2013/08/02 page: 4 / precautions: take note of the following in use of led 1. temperature in use since the light generated inside the led needs to be emitted to outside efficiently, a resin with high light transparency is used; therefore, additives to improve the heat resistance or moisture resistance (silica gel , etc) which are used for semiconductor products such as transistors cannot be added to the resin. consequently, the heat resistant ability of the resin used for led is usually low; therefore, please be careful on the following during use. avoid applying external force, stress, and excessi ve vibration to the resins and terminals at high temperature. the glass transition temperature of epoxy resin used for the led is approximately 120-130 . at a temperature exceeding this limit, the co efficient of liner expansion of the resin doubles or more compared to that at normal temperature and the resin is softened. if external force or stress is applied at that time, it may cause a wire rupture. 2. soldering please be careful on the following at soldering. after soldering, avoided applying external force, stress, and excessive vibration until the products go to cooling process (normal temp erature), (1) soldering measurements: distance between melted solder side to bottom of resin shall be 1.6mm or longer. (2) dip soldering : pre-heat: 90 max. (backside of pcb), within 60 seconds. solder bath: 260 5 (solder temperature), within 5 seconds. (3 ) hand soldering: 350 max. (temperature of soldering iron tip), within 3 seconds. 3. insertion pitch of the led leads and pitch of mounting holes need to be same. 4. others since the heat resistant ability of the led re sin is low, smd components are used on the same pcb, please mount the led after adhesive baking process for smd components. in case adhesive baking is done after led lamp insertion due to a production process reason, make sure not to apply external force, stress, and excessive vibration to the led and follow the conditions below. baking temperature: 120 max. baking time: within 60 seconds. if soldering is done sequentially after the adhesive baking, please perform the soldering after cooling down the led to normal temperature. MT3301N-UY-A 3.0 mm round led lamp
|
