photosensor modules h9306/h9307 series information furnished by hamamatsu is believed to be reliable. however, no responsibility is assumed for possible inaccuracies or omissions. specifications are subject to change without notice. no patent rights are granted to any of the circuits described herein. ?015 hamamatsu photoni cs k.k. subject to local technical requirements and regulations, availability of products included in this promotional material may var y. please consult with our sales office. overview product variations the h9306/h9307 series voltage output type photosensor modules contain a high-voltage power supply circuit, low noise amplifier and 13-mm(1/2") diameter side-on photomultiplier tube. the amplifier contained in h9306 series has 1 v/ a of current to voltage conversion factor and 20 khz of frequency bandwidth. the amplifier contained in h9307 series has 0.1v/ a of current to voltage conversion factor and 200 khz of frequency bandwidth. this product can't be used at vacuum environment or reduced pressure environment. please pay attention when the h9306/h9307 ser ies is used for measuring the light below 190 nm. type no. h9306-01 h9306-02 h9306-03 h9306-13 h9306-04 h9306-05 185 nm to 750 nm 185 nm to 900 nm 185 nm to 900 nm 185 nm to 900 nm 185 nm to 830 nm 185 nm to 650 nm spectral response bialkali multialkali multialkali multialkali multialkali bialkali photocathode uv glass uv glass uv glass uv glass uv glass uv glass window material 1 v/ a current-to-voltage conversion factor dc to 20 khz frequency bandwidth type no. h9307-01 h9307-02 h9307-03 h9307-13 h9307-04 h9307-05 185 nm to 750 nm 185 nm to 900 nm 185 nm to 900 nm 185 nm to 900 nm 185 nm to 830 nm 185 nm to 650 nm spectral response bialkali multialkali multialkali multialkali multialkali bialkali photocathode uv glass uv glass uv glass uv glass uv glass uv glass window material 0.1 v/ a current-to-voltage conversion factor dc to 200 khz frequency bandwidth figure 1: typical spectral response tpmob0154ea tpmob0116ed wavelength (nm) anode radiant sensitivity (v/nw) anode radiant sensitivity (v/nw) 100 100 200 300 400 500 600 700 800 900 10 1 0.1 0.01 10 (h9306) (h9307) 1 0.1 0.01 0.001 pmt gain: 10 5 -01 -05 wavelength (nm) anode radiant sensitivity (v/nw) anode radiant sensitivity (v/nw) 100 100 200 300 400 500 600 700 800 900 10 1 0.1 0.01 10 1 0.1 0.01 0.001 (h9306) (h9307) pmt gain: 10 5 -04 -02 -03 -13
photosensor modules h9306/h9307 series specifications figure 2: schematic diagram *1: input voltage = +15 v, control voltage = +1.0 v, dark current output *2: measured at the peak sensitivity wavelength *3: control voltage = +1.0 v *4: cable rg-174/u, cable length 450 mm, load resistance = 1 m ?, load capacitance = 22 pf *5: the time required for the output to reach a stable level following a change in the control voltage from +1.0 v to +0.5 v. *6: no condensation *7: after 30 minutes storage in darkness parameter h9306/h9307 series input voltage max. input voltage max. input current * 1 max. control voltage recommended control voltage adjustment range effective area peak sensitivity wavelength offset voltage ripple noise * 3 * 4 (peak to peak) settling time * 5 operating ambient temperature * 6 storage temperature * 6 weight 450 350 500 0.4 105 11.5 to 15.5 18 +9/-1 (h9306), +15/-8 (h9307) +1.2 (input impedance : 1 m ? ) +0.25 to +1.0 (input impedance : 1 m ? ) 3.7 13.0 3 0.8 10 +5 to +50 -20 to +50 110 420 80 120 10 90 400 200 300 0.3 77 530 140 200 0.15 70 suffix -03 -01 -02 -04 450 620 650 15 0.43 109 -13 -05 340 20 40 5 48 unit v v ma v v mm nm a/lm ma/w mv mv s c c g luminous sensitivity blue sensitivity index (cs 5-58) red/white ratio radiant sensitivity * 2 min. ty p. ty p. ty p. ty p. ty p. max. max. cathode parameter h9306 series (with internal 20 khz amp) max. output signal voltage current-to-voltage conversion factor 1.0 10 9 2.0 10 9 420 2 10 +10 (load resistance 10 k ? ) 1 1.0 10 8 7.0 10 8 520 1 10 4.0 10 8 1.2 10 9 310 1 10 3.0 10 8 7.0 10 8 250 0.1 1 suffix -03 -01 -02 -04 4.0 10 8 2.6 10 9 430 3 10 -13 -05 5.0 10 7 3.0 10 8 360 0.5 5 unit v/lm v/nw mv v v/ a luminous sensitivity * 3 radiant sensitivity * 2 * 3 voltage output due to pmt dark current * 3 * 7 min. ty p. ty p. ty p. max. anode parameter h9307 series (with internal 200 khz amp) max. output signal voltage current-to-voltage conversion factor 1.0 10 8 2.0 10 8 42 0.2 1 +1 (load resistance 10 k ? ) 0.1 1.0 10 7 7.0 10 7 52 0.1 1 4.0 10 7 1.2 10 8 31 0.1 1 3.0 10 7 7.0 10 7 25 0.01 0.1 suffix -03 -01 -02 -04 4.0 10 7 2.6 10 8 43 0.3 1 -13 -05 5.0 10 6 3.0 10 7 36 0.05 0.5 unit v/lm v/nw mv v v/ a luminous sensitivity * 3 radiant sensitivity * 2 * 3 voltage output due to pmt dark current * 3 * 7 min. ty p. ty p. ty p. max. anode (at +25 c) high voltage power supply circuit amp signal output (voltage output) low voltage input (-15 v) low voltage input (+15 v) vref output (+1.2 v) gnd vcont input (+0.25 v to +1.0 v) (input impedance: 1 m ? )
figure 3: sensitivity adjustment method figure 4: gain figure 5: frequency characteristics tpmob0266ea tpmoc0147ec figure 6: ripple noise tpmob0267ea figure 7: output characteristics h9306 h9307 tpmob0268ea tpmob0269ea tpmob0240eb +15 v -15 v gnd +15 v -15 v gnd signal output coaxial cable red (low voltage input) green (low voltage input) black (gnd) blue (vref output) white (vcontrol input) signal output photosensor module power supply power supply photosensor module +0.25 v to +1.0 v coaxial cable red (low voltage input) green (low voltage input) black (gnd) blue (vref output) white (vcontrol input) potentiometer (10 k ?) monitor cw voltage programming resistance programming adjust the control voltage to adjust the sensitivity. electrically insulate the reference voltage output. when using a potentiometer, adjust sensitivity while monitoring the control voltage. so it does not exceed +1.2 v. gnd control voltage (v) pmt gain 10 7 10 8 10 6 10 5 10 4 10 3 10 2 0.25 0.5 1.1 0.8 0.9 1.2 0.3 0.4 0.6 0.7 1.0 -05 -01 -02/-03/-13 -04 1 ( s/div.) output (1 mv/div.) load resistance: 1 m ? 20 ( s/div.) 500 (mv/div.) load resistance: 1 m ? output signal input light 2 ( s/div.) 500 (mv/div.) load resistance: 1 m ? output signal input light 0.1 1 10 100 -20 -15 -10 -5 -3 0 5 frequency (khz) gain (db) 1000 h9307 h9306
tpmo1069e01 sept. 2015. ip figure 8: dimensional outlines (unit: mm) photosensor modules h9306/h9307 series hamamatsu photonics k.k. hamamatsu photonics k.k., electron tube division 314-5, shimokanzo, iwata city, shizuoka pref., 438-0193, japan, telephone: (81)539/62-5248, fax: (81)539/62-2205 www.hamamatsu.com u.s.a.: hamamatsu corporation: 360 foothill road, bridgewater. n.j. 08807-0910, u.s.a., telephone: (1)908-231-0960, fax: (1)908-231-12 18 e-mail: usa@hamamatsu.com germany: hamamatsu photonics deutschland gmbh: arzbergerstr. 10, d-82211 herrsching am ammersee, germany, telephone: (49)8152-375-0, fa x: (49)8152-2658 e-mail: info@hamamatsu.de france: hamamatsu photonics france s.a.r.l.: 19, rue du saule trapu, parc du moulin de massy, 91882 massy cedex, france, telephone: (3 3)1 69 53 71 00, fax: (33)1 69 53 71 10 e-mail: infos@hamamatsu.fr united kingdom: hamamatsu photonics uk limited: 2 howard court, 10 tewin road, welwyn garden city, hertfordshire al7 1bw, united kingdom, tele phone: (44)1707-294888, fax: (44)1707-325777 e-mail: info@hamamatsu.co.uk north europe: hamamatsu photonics norden ab: torshamnsgatan 35 se-164 40 kista, sweden, telephone: (46)8-509-031-00, fax: (46)8-509-031-01 e -mail: info@hamamatsu.se italy: hamamatsu photonics italia s.r.l.: strada della moia, 1 int. 6, 20020 arese (milano), italy, telephone: (39)02-93581733, fax: (39)02-93581741 e-mail: info@hamamatsu.it china: hamamatsu photonics (china) co., ltd.: b1201 jiaming center, no.27 dongsanhuan beilu, chaoyang district, beijing 100020, china , telephone: (86)10-6586-6006, fax: (86)10-6586-2866 e-mail: hpc@hamamatsu.com.cn tpmoa0013ei tpmoa0018ee details of input window top view front view 8.8 6.0 1.5 photocathode window 9 7 16 13 18 20.5 7 3.7 9 window effective area (3.7 13.0 min.) low voltage input (+15 v) low voltage input (-15 v) gnd vref output (+1.2 v) vcont input (+0.25 v to +1.0 v) signal output : awg26 (red) : awg26 (green) : awg26 (black) : awg26 (blue) : awg26 (white) : rg-174/u 19.7 effective area (3.7 13.0 min.) 49.0 0.5 2.1 11.7 0.2 front view mounting threaded hole (4 m2 depth: 4) 19.0 0.5 window (7 16) 53.2 0.5 50.8 0.5 450 20 side view 8.8 photocathode related product power supply for photomultiplier tube modules c7169 output voltage output current control voltage a (variable voltage range) terminal connection method input voltage operating ambient temperature dimensions (w h d) b weight max. 15 0.3 (+15 v), 0.2 (-15 v) +0.25 to +1.8 binding post ac100 to ac240 +5 to +50 147 61 200 approx. 1.2 description / value v a v v c mm kg unit parameter note: the c7169 is the power supply for photomultiplier tube modules which has 15 v input voltage. this unit can provide both the driving voltage and the control voltage. this feature enables users to operate the modules easily. a adjust within the recommended control voltage range for the photomultiplier tube module being used. b excluding protuberance
|
