es2a thru es2m surface mount super fast rectifier reverse voltage - 50 to 1000 volts forward current - 2.0 amperes note: 1.reverse recovery condition i f =0.5a,i r =1.0a,irr=0.25a 2.measured at 1mhz and applied reverse voltage of 4.0v d.c. maximum ratings and electrical characteristics volts volts volts symbols units amps amps volts v rrm v rms v dc i (av) i fsm v f 2.0 50.0 0.975 operating junction and storage temperature range maximum repetitive peak reverse voltage maximum rms voltage maximum dc blocking voltage maximum average forward rectified current at t l =55 c peak forward surge current 8.3ms single half sine-wave superimposed on rated load (jedec method) maximum instantaneous forward voltage at 2.0a maximum dc reverse current t a =25 c at rated dc blocking voltage t a =100 c i r 5.0 150.0 r q ja c j t j , t stg 20.0 25.0 -50 to +150 pf c a m typical thermal resistance (note 3) c/w typical junction capacitance (note 2) maximum reverse recovery time (note 1) t rr 50 ns es2a es2b es2c es2d es2e es2g es2j ratings at 25 c ambient temperature unless otherwise specified. single phase half-wave 60hz,resistive or inductive load,for capacitive load current derate by 20%. 50 35 50 100 70 100 150 105 150 400 280 400 600 420 600 200 140 200 300 210 300 1.35 case : jedec do-214ac molded plastic body over passivated chip terminals : solder plated, solderable per mil-std-750, method 2026 polarity : color band denotes cathode end mounting position : any weight :0.003 ounce, 0.093 grams features mechanical data 1.7 mdd electronic easy pick and place high temp soldering: 2 6 0 c for 10 seconds at terminals ultrafast case material: molded plastic. ul flammability classification rating 94 v -0 and msl rating 1 lead free finish/rohs compliant (note1) ("p"suffix designates compliant. see ordering information) recovery times for high efficiency es2k es2m 800 1000 800 560 700 1000 60 100 4.high temperature solder exemptions applied, see eu directive annex 7. 3.pulse test: pulse width 200 sec, duty cycle 2% mdd catalog number do-214ac (hsma) (high profile) h j e f g a b d c cat hode b and dimensions inches mm dim min max min max note a .078 .116 1.98 2.95 b .067 .089 1.70 2.25 c .002 .008 .05 .20 d --- .02 --- .51 e .035 .055 .89 1.40 f .065 .09 6 1.65 2. 45 g .205 .224 5.21 5.69 h .160 .180 4.06 4.57 j .100 .112 2.57 2.84
mdd electronic ratings and characteristic curves es2a thru es2m average forward rectified current - amperes versus ambient temperature - c figure 2 forward derating curve 0 150 25 50 75 100 0 .2 .4 .6 .8 1.0 1.2 1.4 single phase, half wave 60hz resistive or inductive load amps c 125 1.6 1.8 2.0 2.2 2.4 figure 3 junction capacitance .1 .2 1 .4 2 10 20 40 4 100 200 1 2 6 10 20 100 junction capacitance - pf versus reverse voltage - volts pf volts 60 40 4 400 1000 t j =25 c instantaneous forward current - amperes versus instantaneous forward voltage - volts figure 1 typical forward characteris tics 4 6 20 10 amps .4 .8 1.2 1.6 2.0 2.4 .01 .02 .04 .06 .1 .2 .4 .6 1 2 volts e s 2a - 2d e s 2g- 2 j e s 2 k-2 m
ratings and characteristic curves es2a thru es2m figure 5 new smb assembly round lead process t rr +0.5a 0 -0.25 -1.0 1cm set time base for 20/100ns/cm 25vdc 1 ? 50 ? 10 ? oscilloscope note 1 pulse generator note 2 notes: 1. rise time = 7ns max. input impedance = 1 megohm, 22pf 2. rise time = 10ns max. source impedance = 50 ohms 3. resistors are non-inductive figure 6 reverse recovery time characteristic and test circuit diagram 1 100 4 0 10 20 30 8 figure 4 peak forward surge current peak forward surge current - amperes versus number of cycles at 60hz - cycles amps cycles 2 6 10 20 60 80 40 40 50 mdd electronic
|
