View KV-PF21P40_7731472.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

kv-pf21l70 rm-952 me scc-u30b-a kv-pf21m40 rm-952 ge scc-u12n-a kv-pf21m70 rm-952 e scc-u13e-a kv-pf21m70 rm-952 me scc-u30c-a kv-pf21p10 rm-952 oce scc-u24d-a KV-PF21P40 rm-952 singapore scc-u29b-a KV-PF21P40 rm-952 malaysia scc-u21c-a kv-pf21p41 rm-952 malaysia scc-u21e-a kv-pf21q70 rm-952 me scc-u30a-a model commander dest. chassis no. chassis trinitron color tv service manual bg-3s self diagnosis supported model model commander dest. chassis no. www.datasheet.co.kr datasheet pdf - http://www..net/
2 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 specifications caution short circuit the anode of the picture tube and the anode cap to the metal chassis, crt shield, or carbon painted on the crt, after removing the anode. safety-related component warning!! components identified by shading and mark ! on the schematic diagrams, exploded views and in the parts list are critical to safe operation. replace these components with sony parts whose part numbers appear as shown in this manual or in supplements published by sony. circuit adjustments that are critical to safe operation are identified in this manual. follow these procedures whenever critical components are replaced or improper operation is suspected. note power requirements 110-240 v ac, 50/60 hz except malaysia and oce 220-240v ac, 50/60hz for malaysia and oce power consumption (w) indicated on the rear of the tv television system b/g, i, d/k, m kv-pf21m40/pf21m70 b/g except kv-pf21m40/pf21m70 color system pal, pal60, secam, ntsc4.43, ntsc3.58 kv-pf21m70 (me)/ kv-pf21m40/pf21m70(e) pal, pal60, ntsc4.43, ntsc3.58 (av in) kv-pf21p10/pf21p40/pf21p41 pal, pal60, secam, ntsc4.43, ntsc3.58 (av in) kv-pf21l70 pal, pal60, secam, ntsc4.43 pf21q70 teletext language english, arabic, french kv-pf21p41 only channel coverage b/g vhf : e2 to e12/ uhf : e21 to e69/ catv : s01 to s03, s1 to s41 vhf : 0 to 12, 5a, 9a uhf : 28 to 69 catv : s01 to s03, s1 to s41 australia only vhf : 1 to 11 uhf : 21 to 69 catv : s01 to s03, s1 to s41 new zealand only i uhf : b21 to b68/ catv : s01 to s03, s1 to s41 kv-pf21m40/pf21m70 d/k vhf : c1 to c12, r1 to r12/ uhf : c13 to c57, r21 to r60 catv: z1 to z39, s01 to s03, s1 to s41 kv-pf21m40/pf21m70 m vhf : a2 to a13/ uhf : a14 to a79/ catv : a-8 to a-2, a to w+4, w+6 to w+84 kv-pf21m40/pf21m70 ? ? ? ? ? (antenna) 75-ohm external terinal audio output 3w number of terminal (video) input : 2 output : 1 phono jacks; 1 vp-p, 75 ohms (audio) input : 2 output : 1 phono jacks; 500 mvrms (earphone) output : 1 minijack picture tube 21 inch tube size (cm) 54 measured diagonally screen size (cm) 51 measured diagonally dimension (w/h/d, mm) 490 x 458 x 487 mass (kg) 25 design and specifications are subject to change without notice. ? www.datasheet.co.kr datasheet pdf - http://www..net/
3 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 table of contents section title page self diagnosis function ................................ 4 1. general .......................................................... 8 2. disassembly 2-1. rear cover removal ................................................ 23 2-2. chassis assy removal ............................................. 23 2-3. f bracket removal .................................................. 23 2-4. service position ....................................................... 23 2-5. replacement of parts ............................................... 24 2-5-1. replacement of control button ....................... 24 2-5-2. replacement of bar control ............................. 24 2-6. terminal bracket removal ...................................... 24 2-7. v1 board removal .................................................. 24 2-8. degauss coil removal ............................................. 25 2-9. picture tube removal .............................................. 25 3. set-up adjustments 3-1. beam landing .......................................................... 27 3-2. convergence ............................................................. 28 3-3. focus adjustment .................................................... 30 3-4. g2 (screen) and white balance adjustments ......... 30 4. circuit adjustments 4-1. adjustments with commander ................................ 31 4-2. adjustment method ................................................. 32 4-3. picture quality adjustments .................................... 37 4-4. a board adjustment after ic003 (memory) replacement ............................................................. 37 4-5. picture distortion adjustment ................................. 38 section title page 5. diagrams 5-1 block diagram ......................................................... 41 5-2 frame schematic diagram ...................................... 44 5-3 circuit boards location .......................................... 46 5-4 schematic diagrams and printed wiring boards ... 47 (1) schematic diagram of a(1/2) board ....................... 49 (2) scheamtic diagram of a(2/2) board ....................... 53 (3) schematic diagrams of c3 and f boards ............... 61 (4) schematic diagram of v1 board ............................ 65 5-5 semicondutors ......................................................... 68 6. exploded view 6-1. chassis ..................................................................... 71 7. electrical parts list ................................... 73 www.datasheet.co.kr datasheet pdf - http://www..net/
4 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 the units in this manual contain a self-diagnostic function. if an error occurs, the standby/timer lamp will automatically begin to flash. the number of times the lamp flashes translates to a probable source of the problem. a definition of the standby/timer lamp flash indicators is listed in the instruction manual for the user s knowledge and reference. if an error symptom cannot be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to reveal past problems and how often these problems occur. 1. diagnostic test indicators when an errors occurs, the standby/timer lamp will flash a set number of times to indicate the possible cause of the problem. if there is more than one error, the lamp will identify the first of the problem areas. result for all of the following diagnostic items are displayed on screen. no error has occured if the screen displays a 0 . diagnostic item description power does not turn on +b overcurrent (ocp) or overvoltage (ovp) vertical deflection stopped horizontal deflection overdrive white balance failure (no picture) micro reset no. of times standby/timer lamp flashes does not light 2 times 5 times self-diagnostic display/diagnostic result 002:000 or 002:001~255 003:001~255 004:001~255 at the same time 005:000 or 005:001~225 101:00 or 101:001~225 probable cause location power cord is not plugged in. fuse is burned out f4601 (f board) h.out q511 is shorted. (a board) -13v is not supplied. (a board) ic 503 faulty (a board) ic 301 faulty (a board) g2 is improperly adjusted. (note 2) crt problem. ic301 is faulty. (a board) no connection a board to c3 board. discharge crt (c3 board) static discharge external noise detected symptoms power does not come on. no power is supplied to the tv. ac power supply is faulty. power does not come on. load on power line is shorted. has entered standby state after horizontal raster. vertical deflection pulse is stopped. power line is shorted or power supply is stopped. no raster is generated. crt cathode current detection reference pulse output is small. power is shut down shortly, after this return back to normal. detect micro latch up. note 1: if a + b overcurrent is detected, stoppage of the vertical deflection is detected simultaneously. the symptom that is diagnosed first by the microcontroller is displayed on the screen. note 2: refer to screen (g2) adjustment in section 3-4 of this manual. self diagnostic function www.datasheet.co.kr datasheet pdf - http://www..net/
5 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 2. display of standby/timer light flash count diagnostic item flash count* +b overcurrent/overvoltage 2 times vertical deflection stopped white balance failure 5 times * one flash count is not used for self-diagnostic. 3. stopping the standby/timer flash turn off the power switch on the tv main unit or unplug the power cord from the outlet to stop the standby/timer lamp from flashing. lamp on 0.3 sec. lamp off 3 sec. lamp off 0.3 sec. 2 times 5 times standby/sleep lamp www.datasheet.co.kr datasheet pdf - http://www..net/
6 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 4. self-diagnostic screen display for errors with symptoms such as power sometimes shuts off or screen sometimes goes out that cannot be confirmed, it is possible to bring up past occurances of failure for confirmation on the screen: [to bring up screen test] in standby mode, press buttons on the remote commander sequentially in rapid succession as shown below: [screen?display] / channel [5] / sound volume [-] / power on ? note that this differs from entering the service mode (mode volume [+] ). self-diagnosis screen display 002 : 000 003 : 000 004 : 000 005 : 001 101 : 000 self diagnostic 5. handling of self-diagnostic screen display since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen during repairs. when you have completed the repairs, clear the result display to 0 . unless the result display is cleared to 0 , the self-diagnostic function will not be able to detect subsequent faults after completion of the repairs. [clearing the result display] to clear the result display to 0 , press buttons on the remote commander sequentially as shown below when the diagnostic screen is being displayed. channel [8] / 0 [quitting self-diagnostic screen] to quit the entire self-diagnostic screen, turn off the power switch on the remote commander or the main unit. numeral "0" means that no fault has been detected. numeral "1" means a fault has been detected. www.datasheet.co.kr datasheet pdf - http://www..net/
7 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 6. self-diagnostic circuit [+b?overcurrent?aocpo] occurs when an overcurrent on the +b(135) line is detected by q604. if q604 go to on and the voltage to pin 18 of ic301 should go down when v.sync is more than seven verticals in a period, the unit will automatically turn off. [vertical?deflection?stopped] occurs when an absence of the vertical deflection pulse is detected by q509 and ic001 shut down the power supply. [vertical?deflection?overcurrent] occurs when an overcurrent on v drive line is detected by q507. power supply will be shut down when detect this by ic001. [white?balance?failure] if the rgb levels* do not balance or become low level within 5 seconds, this error will be detected by ic301. tv will stay on, but there will be no picture. * (refers to the rgb levels of the akb detection ref pulse that detects ik.) ic301 y/chroma jungle from crt from [+b] q604 c3 [v] q509/507 ic001 system ic003 memory b-dat io-sdat ik-in mp/ protect io-8dat o-led sda 5 45 21 18 51 46 35 www.datasheet.co.kr datasheet pdf - http://www..net/
8 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 section 1 general the operating instructions mentioned here are partial abstracts from the operating instruction manual. the page numbers of the operating instruction manual remain as in the manual. 2 warning ? dangerously high voltages ar e present inside the tv . ? tv operating voltage: 1 10 C 240 v ac. (for malaysia only: 220 C 240 v ac.) to prevent fire or shock hazard, do not expose the tv to rain or moisture. do not operate the tv if any liquid or solid object falls into it. have it checked immediately by qualified personnel only. do not open the cabinet and the rear cover of the tv. refer servicing to qualified personnel. do not install the tv in hot, humid or excessively dusty places. do not install the tv in a confined space, such as a bookcase or built-in cabinet. do not block the ventilation openings of the tv. do not pull the power cord to disconnect the tv. pull it out by the plug. disconnect the power cord during lightning storms or if you are not going to use the tv for several days. install the tv in a stable position. do not allow children to climb onto it. do not plug in too many appliances to the same power socket. do not damage the power cord. clean the tv with a dry and soft cloth. do not use benzine, thinner, or any other chemicals to clean the tv. do not scratch the picture tube. 4 using your new tv getting started step 1 connect the antenna (except kv -pf21p10) if you wish to connect a vcr, see the connecting a vcr diagram below . using your new tv iec connector (not supplied) to video and audio outputs vcr (yellow) (black) antenna cable (not supplied) to 1 (video input) audio/video cable (not supplied) : signal flow to antenna output antenna cable (not supplied) rear of tv connecting a vcr to watch the video, pr ess (see page 12). note ? you are advised to use an outdoor antenna for better r eception. or : signal flow video video in video out audio 1 rear of tv rod antenna and cable (supplied for kv -pf21p40 only) or to ? (antenna) www.datasheet.co.kr datasheet pdf - http://www..net/
9 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 4 using your new tv getting started step 1 connect the antenna (pf21p10) if you wish to connect a vcr, see the connecting a vcr diagram below . using your new tv iec connector (not supplied) antenna cable (not supplied) : signal flow rear of tv or 5 using your new tv using your new tv preset the channels automatically tips ? if you want to stop automatic channel pr esetting, press select twice. ? if your tv has pr eset an unwanted channel or cannot pr eset a particular channel, then preset your tv manually (see page 9). note (kv-pf21m40/pf21m70 only) ? during automatic channel pr esetting, your tv scr een will indicate b/g , i , d/k or m for the tv system. now you are ready. . . to watch your tv, see page 11. notes ? if you connect a ster eo vcr, connect the yellow plug to (the yellow jack) and the white plug to (the black jack). ? if you connect a vcr to the ? (antenna) terminal, pr eset the signal output from the vcr to the pr ogram number 0 on the tv . ? when no signal is input to the connected video equipment, the tv scr een becomes blue. step 2 note ? do not use old batteries nor use dif ferent types of batteries together . step 3 caution do not connect the power cor d until you have completed making all other connections; otherwise a minimum leakage curr ent might flow thr ough the antenna and other terminals to gr ound. insert the batteries into the remote front of tv 1 1 1 2 vhf low b/g www.datasheet.co.kr datasheet pdf - http://www..net/
10 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 7 using your new tv using your new tv securing the tv to prevent the tv from falling, secur e the tv using one of the following methods: a with the supplied screws, attach the band to the tv stand and to the rear of the tv using the provided hole. or b put the cord or chain through the clamps to secure the tv against a wall or pillar. note ? use only the supplied scr ews. use of other scr ews may damage the tv . 20 mm a b 3.8mm or 6 using your new tv connecting optional components you can connect optional video components, such as a vcr, multi disc player , camcorder or video game. to watch the pictur e of the connected equipment, pr ess (see page 12). connecting a camcor der/video game equipment using the (video input) jacks note ? you can also connect video equipment to the 1 (video input) jacks at the rear of your tv. connecting video equipment using the (monitor output) jacks note ? when connecting a ster eo vcr, connect the yellow plug to (the yellow jack) and the white plug to (the black jack). front of tv camcorder video game equipment to video and audio outputs (yellow) (black) rear of tv to antenna output vcr : signal flow to 2 (video input) to (monitor output) or audio/video cable (not supplied) antenna cable (not supplied) 2 1 audio/video cable (not supplied) : signal flow to video and audio inputs www.datasheet.co.kr datasheet pdf - http://www..net/
11 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 8 using your new tv presetting channels you can preset up to 100 tv channels in numerical sequence fr om program number 1 using the r emote and the buttons on your tv as well. presetting channels automatically 1 press u to turn on the tv. 2 press auto progr. note (kv-pf21m40/pf21m70 only) ? during automatic channel pr esetting, your tv scr een will indicate b/g , i , d/k or m for the tv system. to preset channels automatically fr om a specified pr ogram number (1) press select until aut o program appears. (2) press + or C . the on-screen display will start flashing. (3) press progr +/ C or the number buttons until the desir ed program number appears. (4) press + or C . u number buttons select . +/ progr +/ + or pic mode tv 1 2 3 4 6 7 8 9 0 5 jump sound mode favorite progr 9 using your new tv using your new tv presetting channels manually 1 press select until ?anual program appears. 2 press + or ? 3 press progr +/?or the number buttons until the desired program number appears. 4 press + or ?until the desired channel picture appears. 5 press select. to change the color system setting (kv-pf21p10/pf21p40/pf21p41) if the color is abnormal when r eceiving programs through the ? (antenna) terminal or the (video input) jack (1) press select until col sys appears. (2) press + or C to select the appr opriate color system until the color is optimal. tip ? normally set col sys to auto . continued manual program select vhf low b/g or 1 2 3 4 5 6 7 8 0 -/-- 9 progr 1 select col sys: auto auto pal ntsc 3.58 ntsc 4.43 www.datasheet.co.kr datasheet pdf - http://www..net/
12 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 10 using your new tv to change the tv system setting (kv -pf21m40/pf21m70 only) if the picture or sound is abnormal when r eceiving programs through the ? (antenna) terminal (1) press select until tv sys appears. (2) press + or C to select the appr opriate tv system until the pictur e or sound quality is optimal. note ? the tv system i and m ar e available for kv -pf21m70 only. skipping program numbers 1 press progr +/ or the number buttons until the unused or unwanted program number appears. 2 press select until manual program appears. 3 press + or . 4 press pic mode. 5 press select. to preset the skipped pr ogram number again preset the channel automatically or manually . tip ? you can also use select and ? +/ C on the tv to pr eset channels and skip program numbers. to use the fine tuning (fine) function the fine tuning (fine) function may help to r educe the following pr oblems: double images and lines moving acr oss the tv screen. you can use the fine tuning function as below: (1) select the program number you want to adjust. (2) press select until manual program appears on the scr een. (3) press + or C on the r emote control once. (4) press to display fine on the scr een. (5) press + or C continuously until the above pr oblems are minimized. the + or C icon on the scr een flashes while tuning. (6) press select to r eturn to normal scr een. presetting channels (continued) tv sys: b/g b/g i d/k m 9 using your new tv using your new tv to change the color system setting (kv-pf21l70/pf21m40/pf21m70/pf21q70) if the color is abnormal when r eceiving programs through the ? (antenna) terminal or the (video input) jack (1) press select until col sys appears. (2) press + or C to select the appr opriate color system until the color is optimal. tip ? normally set col sys to auto . note ? the color system ntsc3.58 is not available for kv -pf21q70. continued col sys: auto auto pal secam ntsc 3.58 ntsc 4.43 www.datasheet.co.kr datasheet pdf - http://www..net/
13 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 11 using your new tv using your new tv watching the tv this section explains functions used while watching the tv . most operations can be done using the r emote. 1 press u to turn on the tv. when the tv is in the standby mode (the u indicator on the tv is lit red), press u on the remote or progr +/ C on the tv . 2 press progr +/ or the number buttons to select the tv program. for double digit numbers, press , then the number (e.g., for 25, press , then 2 and 5). 3 press . +/ to adjust the volume. u ; number buttons select . +/ progr +/ + or jump or continued tv 1 2 3 4 6 7 8 9 0 5 jump sound mode favorite progr select p pic mode p progr 12 using your new tv to turn off temporarily turn off completely mute the sound watch the video input (vcr, camcorder, etc.) jump back to the pr evious channel display the on-scr een information* adjust the volume of each tv program automatically do this press u . the u indicator on the tv lights up r ed. press u on the tv. press . press to select video 1 or video 2 . to return to the tv pr ogram, press ; . press jump. press . press select repeatedly until intelligent vol appears, then press + or C to select on . to cancel, select off . * the picture, sound, and either the pr ogram number or video mode ar e displayed. the on-scr een display for the pictur e and sound information disappears after about 3 seconds. changing the on-scr een display language (except kv-pf21l70/pf21m70(me)/pf21q70) 1 press select until language / : english appears on the screen. 2 press + or to select . tip ? you can also use select and . +/ C on the tv to select the on-scr een display language. additional tasks watching the tv (continued) select language / : english / language : www.datasheet.co.kr datasheet pdf - http://www..net/
14 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 13 using your new tv using your new tv setting the wake up timer 1 press until the desired period of time appears. 2 select the tv program or video mode you want to display when you wake up. 3 press u or set the sleep timer if you want the tv to tur n off automatically. the indicator on the tv lights up orange. to cancel the wake up timer press until wake up timer: off appears or turn of f the tv s main power . notes ? the wake up timer starts immediately after the on-scr een display disappears. ? if no buttons or contr ols are pressed for more than two hours after the tv is turned on using the w ake up timer, the tv automatically goes into the standby mode. t o continue watching the tv , press any button or control on the tv or the r emote. setting the sleep timer press until the desired period of time appears. to cancel the sleep timer press until sleep timer: off appears or turn the tv of f. wake up timer:10m wake up timer:off wake up timer:12h00m after 10 minutes no wake up timer after 12 hours sleep timer:30m sleep timer:60m sleep timer:off sleep timer:90m after 30 minutes no sleep timer after 60 minutes after 90 minutes 12 using your new tv changing the on-scr een display language (kv-pf21l70/pf21m70(me)/pf21q70) 1 press select until language / : english appears on the screen. 2 press + or to select . tip ? you can also use select and . +/ C on the tv to select the on-scr een display language. watching the tv (continued) language / : english select language / : www.datasheet.co.kr datasheet pdf - http://www..net/
15 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 14 advanced operations advanced operations sound mode customizing the picture and sound you can customize the pictur e and sound by selecting the pictur e and sound modes or by adjusting its settings. selecting the pictur e and sound modes to select the pictur e mode press pic mode repeatedly until you get the desired picture mode. select to dynamic receive high contrast pictur es. standard receive normal contrast pictur es. soft receive mild pictur es. to select the sound mode press sound mode repeatedly until you get the desired sound mode. select to dynamic listen to dynamic and clear sound that emphasizes the low and high sound. drama listen to sound that emphasizes vocals and backgr ound music. soft receive soft sound. pic mode select + or sound mode favorite progr pic mode dynamic drama soft sound mode 15 advanced operations adjusting the pictur e and sound settings 1 press select until the desired setting appears. each time you pr ess select, the setting item will change as follows: 2 press + or to adjust the item. 3 to adjust other items, r epeat steps 1 to 2. * hue can be adjusted for the ntsc system only . notes ? when you select a pictur e or sound mode, the adjusted settings will be reset according to the selected mode. ? you can also use select and ? +/ C on the tv to adjust the pictur e and sound settings. select picture 60 picture color bright hue* treble bass sharp advanced operations www.datasheet.co.kr datasheet pdf - http://www..net/
16 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 16 advanced operations blocking the channels (child lock) you can prevent a child from watching certain programs by using the buttons on the remote control. 1 select the tv program you want to lock. 2 press select until child lock appears on the screen. 3 press + or to select on . the symbol appears on the screen. to unlock the channel, press + or C to select off . the symbol disappears from the screen. note ? if you preset a locked channel, that particular channel will be unlocked automatically. select + or tv 1 2 3 4 6 7 8 9 0 5 jump sound mode favorite progr select child lock: on 1 17 advanced operations viewing teletext (kv-pf21p41 only) tv stations broadcast an information service called teletext via some tv channels. teletext allows you to r eceive various information, such as shar es market or news. displaying teletext 1 select a tv channel that carries the teletext broadcast you want to watch. 2 press to display the text. a teletext page (normally the index page) is displayed. if ther e is no teletext broadcast, 100 is displayed at the top left corner of the screen. to turn off teletext press ; . ; a/b fastext v tv 1 2 3 4 6 7 8 9 0 5 jump sound mode favorite progr p166 sectext 166 fr1 mar 03:59:09 fom singapore to paris to osaka to roma to sydney day dep/arr flight alrcraft 1.6 220/0588 sq28 747 2 2130/1225 pa115 l15 3 2115/1330 sq26 747 2.7 2130/0745 sq24 747 4 2300/0915 az487 747 2.5 1000/1715 sq6 747 4.6 0930/2015 cx522 l10 1 2210/0610 sq21a 747 2 2100/0835 sq21a 747 continued www.datasheet.co.kr datasheet pdf - http://www..net/
17 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 18 advanced operations additional teletext tasks to display a teletext page on the tv picture check the contents of a t eletext service select a teletext page hold a teletext page (stop the page fr om scrolling) reveal concealed information (e.g., an answer to a quiz) enlarge the teletext display wait for a teletext page while watching a tv program * you can also select a t eletext page of any page number that appears in the colored column at the bottom of the scr een using the corr esponding color - coded button on the r emote. using fastext this feature allows you to quickly access a t eletext page that uses fastext. when a fastext program is broadcasted, the color ed menus appear at the bottom of the scr een. the colors of the menus correspond to the red, green, yellow, and blue color-coded buttons on the remote. to access a fastext menu press the color-coded button on the r emote corresponding to the menu you want. the menu page appears on the scr een after several seconds. do this press . each time you pr ess , the screen changes as follows: teletext n teletext and tv n tv. press . an overview of the t eletext contents and page numbers appear on the scr een. press the number buttons to enter the thr ee-digit page number of the desir ed teletext page.* if you make a mistake, r eenter the correct page number . to access the next or pr evious page, press progr +/ C . press to display the symbol j at the top left corner of the scr een. to resume normal teletext operation, press or . press . to conceal the information, pr ess the button again. press a/b . each time you pr ess a/b , the teletext display changes as follows: enlar ge upper half n enlarge lower half n normal size. 1 enter the teletext page number that you want to refer to, then press . 2 when the page number is displayed, pr ess to show the text. viewing teletext (continued) 19 additional information self-diagnosis function your tv is equipped with a self-diagnosis function. if ther e is a problem with your tv , the u indicator flashes r ed. the number of times the u indicator flashes indicates the possible causes. 1 check that the u indicator flashes red a number of times between 3-second intervals. 2 count the number of times the u indicator flashes. 3 press u (main power) to tur n off your tv. 4 inform your nearest sony service center about the number of times the u indicator flashes. be sure to note the model name and serial number located on the rear of your tv. front of tv u indicator additional information www.datasheet.co.kr datasheet pdf - http://www..net/
18 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 20 additional information c snowy distorted noisy/ picture picture distorted sound wall antenna terminal uhf vhf booster vcr check the antenna dir ection. incorrect antenna direction may cause: check the antenna type. wrong type of antenna may cause: no picture snowy picture check connection on the wall antenna terminal. loose connection may cause: snowy picture distorted sound check if you need booster to increase signal level. too strong signal level may cause: distorted picture noisy sound troubleshooting shor tcuts for better viewing, please check the following connections. antenna connection 21 additional information p166 sectext 166 fr1 mar 03:59:09 fom singapore to paris to osaka to roma to sydney day dep/arr flight alrcraft 1.6 220/0588 sq28 747 2 2130/1225 pa115 l15 3 2115/1330 sq26 747 2.7 2130/0745 sq24 747 4 2300/0915 az487 747 2.5 1000/1715 sq6 747 4.6 0930/2015 cx522 l10 1 2210/0610 sq21a 747 2 2100/0835 sq21a 747 check connection on the vcr and on the tv. loose connection may cause: snowy picture distorted sound no picture for more information, please see troubleshooting on page 22, 23 and 24. or consult your dealer for guidance. additional information check connection on the ac socket. loose connection may cause: no power no picture with no sound ac connection connection to tv double image missing picture teletext characters (kv-pf21p41 only) www.datasheet.co.kr datasheet pdf - http://www..net/
19 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 18 additional information snowy picture noisy sound distorted picture noisy sound good picture noisy sound no picture no sound troubleshooting (kv-pf21l70/pf21m70(me)/pf21q70) if you find any pr oblem while viewing your tv , please check the following guide. if any problem persists, contact your sony dealer . possible cause symptom solutions ? check the antenna cable and connection on the tv, vcr and on the wall. (page 4) ? press select until manual program appears on the scr een then preset the channel again. (page 9) ? check the antenna type (vhf/uhf). contact a sony dealer for advice. ? adjust the antenna dir ection. contact a sony dealer for advice. ? try using a booster . ? turn off or disconnect the booster if it is in use. ? if the sound of some channels ar e noisy, select the channel, then select the appropriate tv system (tv sys). (page 10) ? check the power cor d, antenna and the vcr connections. ? press u (power). ? press u (main power) on the tv to turn off the tv for about five seconds, then turn it on again. ? connection is loose or the cable is damaged. ? channel presetting is inappropriate or incomplete. ? the antenna type is inappropriate. ? the antenna direction is inappropriate. ? signal transmission is low . ? broadcast signals ar e too strong. ? the tv system setting is inappropriate. ? the power cord, antenna or vcr is not connected. ? the tv is not turned on. 18 additional information snowy picture noisy sound distorted picture noisy sound good picture noisy sound no picture no sound troubleshooting (kv-pf21m40/pf21m70(e)) if you find any pr oblem while viewing your tv , please check the following guide. if any problem persists, contact your sony dealer . possible cause symptom solutions ? check the antenna cable and connection on the tv, vcr and on the wall. (page 4) ? press select until manual program appears on the scr een then preset the channel again. (page 9) ? check the antenna type (vhf/uhf). contact a sony dealer for advice. ? adjust the antenna dir ection. contact a sony dealer for advice. ? try using a booster . ? turn off or disconnect the booster if it is in use. ? if the sound of all the channels ar e noisy, check the tv system (tv sys) setting (page 10), then pr ess auto progr to preset the channels again (page 8). ? if the sound of some channels ar e noisy, select the channel, then select the appropriate tv system (tv sys). (page 10) ? check the power cor d, antenna and the vcr connections. ? press u (power). ? press u (main power) on the tv to turn off the tv for about five seconds, then turn it on again. ? connection is loose or the cable is damaged. ? channel presetting is inappropriate or incomplete. ? the antenna type is inappropriate. ? the antenna direction is inappropriate. ? signal transmission is low . ? broadcast signals ar e too strong. ? the tv system setting or channel presetting is inappropriate or incomplete. ? the power cord, antenna or vcr is not connected. ? the tv is not turned on. www.datasheet.co.kr datasheet pdf - http://www..net/
20 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 18 additional information troubleshooting (kv-pf21p10) if you find any pr oblem while viewing your tv , please check the following guide. if any problem persists, contact your sony dealer . snowy picture noisy sound distorted picture noisy sound good picture noisy sound no picture no sound possible cause symptom solutions ? check the antenna cable and connection on the tv, vcr and on the wall. (page 4) ? press select until manual program appears on the scr een then preset the channel again. (page 9) ? check the antenna type (vhf/uhf). contact a sony dealer for advice. ? adjust the antenna dir ection. contact a sony dealer for advice. ? try using a booster . ? turn off or disconnect the booster if it is in use. ? if the sound of all the channels ar e noisy, press auto progr to preset the channels again (page 8). ? check the power cor d, antenna and the vcr connections. ? press u (power). ? press u (main power) on the tv to turn off the tv for about five seconds, then turn it on again. ? connection is loose or the cable is damaged. ? channel presetting is inappropriate or incomplete. ? the antenna type is inappropriate. ? the antenna direction is inappropriate. ? signal transmission is low . ? broadcast signals ar e too strong. ? channel presetting is inappropriate or incomplete. ? the power cord, antenna or vcr is not connected. ? the tv is not turned on. 22 additional information snowy picture noisy sound distorted picture noisy sound no picture no sound troubleshooting (KV-PF21P40/pf21p41) if you find any pr oblem while viewing your tv , please check the following guide. if any problem persists, contact your sony dealer . possible cause symptom solutions ? check the antenna cable and connection on the tv, vcr and on the wall. (page 4) ? press select until manual program appears on the scr een then preset the channel again. (page 9) ? check the antenna type (vhf/uhf). contact a sony dealer for advice. ? adjust the antenna dir ection. contact a sony dealer for advice. ? try using a booster . ? turn off or disconnect the booster if it is in use. ? check the power cor d, antenna and the vcr connections. ? press u (power). ? press u (main power) on the tv to turn off the tv for about five seconds, then turn it on again. ? connection is loose or the cable is damaged. ? channel presetting is inappropriate or incomplete. ? the antenna type is inappropriate. ? the antenna direction is inappropriate. ? signal transmission is low . ? broadcast signals ar e too strong. ? the power cord, antenna or vcr is not connected. ? the tv is not turned on. www.datasheet.co.kr datasheet pdf - http://www..net/
21 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 23 additional information continued possible cause symptom solutions good picture no sound dotted lines or stripes double images or ghosts n o color abnormal color patches ? press ? + to increase the volume level. ? press to cancel the muting. ? do not use a hair dryer or other equipment near the tv . ? adjust the antenna dir ection for minimum interfer ence. contact a sony dealer for advice. ? use a highly directional antenna. ? use the fine tuning (fine) function. (page 10) ? adjust the antenna dir ection. contact a sony dealer for advice. ? turn off or disconnect the booster if it is in use. ? press select until color appears on the screen, then press + or C to adjust the color level. (page 15) ? press select until col sys appears on the screen, then check the color system setting (usually set this to auto ). (page 9). ? adjust the antenna dir ection. contact a sony dealer for advice. ? keep external speakers or other electrical equipment away fr om the tv. do not move the tv while the tv is turned on. press u (main power) on the tv to turn of f the tv for about five minutes, then turn it on again. ? the volume level is too low . ? the sound is muted. ? there is local interference from cars, neon signs, hair dryers, power generators, etc. ? broadcast signals ar e reflected by nearby mountains or buildings. ? the antenna direction is inappropriate. ? use of a booster is inappropriate. ? the color level setting is too low. ? the color system setting is inappropriate. ? the antenna direction is inapproriate. ? the magnetic disturbance from external speakers or other equipment, or the direction of the earth s magnetic field may af fect the tv. 24 additional information lines moving acr oss the tv screen. the u indicator on your tv flashes red a number of times between 3-second intervals. tv cabinet creaks. a boom sound is hear d when the tv is tur ned on. possible cause symptom solutions ? use the fine tuning (fine) function. (page 10) ? contact your near est sony service center. (page 19) ? there is interference from external sources, e.g., heavy machineries, nearby broadcast station. ? your tv may need service. ? changes in room temperature sometimes make the tv cabinet expand or contract, making a noise. this does not indicate a malfunction. ? the tv s demagnetizing function is working. this does not indicate a malfunction. troubleshooting (continued) www.datasheet.co.kr datasheet pdf - http://www..net/
22 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 25 additional information identifying par ts and controls refer to the pages indicated in par entheses ( ) for details. front panel 1 u (main power) button (5) 2 progr +/ (program) buttons (11) 3 ? +/ (volume) buttons (11) 4 (tv/video) button (12) 5 auto progr (program) button (5) 6 select button (9) 7 a (earphone) jack 2 26 additional information remote contr ol 9 !o !? !? ! ! ! ! button function for general tv operations for teletext operations 1 u (power) button (11) 2 ; (tv) button (12) 3 number buttons (11) 4 jump button (12) 5 progr +/ buttons (11) 6 select button (9) 7 pic mode button (14) 8 + or buttons (9) 9 (display) button (12) !o (muting) button (12) !? (video) button (12) !? . +/ (volume) buttons (11) ! a/b button (not used for these models) ! timer setting buttons (13) (wake up timer) (sleep timer) ! favorite button (not used for these models) ! sound mode button (14) !? teletext operation buttons (17) ( kv-pf21p41 only) (text) (enlarge) (reveal) (hold) (index) (text clear) p (fastext: red, green, yellow, blue) names/symbols of buttons on the remote are indicated in dif ferent colors to represent the available functions. label color white green 1 2 3 4 5 6 7 8 !? tv 1 2 3 4 6 7 8 9 0 5 jump sound mode favorite progr select p pic mode p tv 1 2 3 4 6 7 8 9 0 5 jump sound mode favorite progr select p pic mode p www.datasheet.co.kr datasheet pdf - http://www..net/
23 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 section 2 disassembly 2-2. chassis assy remo val 1 chassis assy lever lever 2-1. rear cover removal six screws (bvtp 4 16) 1 2 two screws (bvtp 4 16) rear cover 2-3. f bracket removal 1 three connectors 2 f board lever one screw (bvtp 4 16) 1 2-4. service position (note: remove f bracket first.) www.datasheet.co.kr datasheet pdf - http://www..net/
24 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 2-6. terminal bra cket removal a board terminal board bracket one screw (bvtp 4 16) 1 2-5. replacement of parts for replacement of the multi button and bar optical ,unscrew to exchange with the new parts, and fix them with screws (+bvtp) respectively . 2-5-1. replacement of mul ti button multi button two screws (bvtp 3 12) 2-5-2. replacement of bar optical bar optical one screw (bvtp 3 12) 1 two claws 2 v1 board 2-7. v1 board removal www.datasheet.co.kr datasheet pdf - http://www..net/
25 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 2-9. picture tube removal note : the picture tube for oce model is upside down, and the positon for the anode cap and tension springs are changed accordingly . 2 a board 4 c3 board 5 deflection yoke cushion 6 four screws (tapping screws) 1 anode cap 3 f board 2-8. degauss coil remo val 1 demagnetization coil 2 tension spring picture tube www.datasheet.co.kr datasheet pdf - http://www..net/
26 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 ? removal of anode-cap note : after removing the anode, short circuit the anode of the picture tube and the anode cap to the metal chassis, cr t shield or carbon paint on the crt. ? removing procedures 1 do not damage the surface of anode-caps with sharp shaped objects. 2 do not press the rubber too hard so as not to damage the inside of anode-cap. a metal fitting called the shatter -hook terminal is b uilt into the rubber . 3 do not turn the foot of rubber over too hard. the shatter-hook terminal will stic k out or damage the rubber. ? how to handle an anode-cap 3 when one side of the rubber cap is separated from the anode button, the anode-cap can be removed by turning up the rubber cap and pulling it up in the direction of the arrow c . 2 using a thumb pull up the rubber cap firmly in the direction indicated by the arrow b . 1 turn up one side of the rubber cap in the direction indicated b y the arrow a . a a b b c anode button www.datasheet.co.kr datasheet pdf - http://www..net/
27 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 ? the following adjustments should be made when a complete realignment is required or a new picture tube is installed. ? these adjustments should be performed with rated power supply voltage unless otherwise noted. controls and switches should be set as follows unless otherwise noted: picture control ........................................................... normal brightness control ................................................... normal perform the adjustments in the following order : 1. beam landing 2. convergence 3. focus 4. white balance note : test equipment required. 1. color-bar/pattern generator 2. degausser 3. oscilloscope section 3 set-up adjustments ............................................................................................................................... ................................................................................................. fig. 3-3 } normal purity control fig. 3-1 red blue green preparation : ? in order to reduce the influence of geomagnetism on the set's picture tube, face it east or west. ? switch on the set's power and degauss with the degausser. 3-1. beam landing 1. input a white signal with the pattern generator. contrast brightness 2. set the pattern generator raster signal to a green raster. 3. move the deflection yoke to the rear and adjust with the purity control so that the green is at the center and the blue and the red take up equally sized areas on each side. (see figures 3-1 through 3-3.) 4. move the deflection yoke forward and adjust so that the entire screen is green. (see figure 3-1.) 5. switch the raster signal to blue, then to red and verify the condition. 6. when the position of the deflection yoke has been decided, fasten the deflection yoke with the screws and dy spacers. 7. if the beam does not land correctly in all the corners, use a magnet to adjust it. (see figure 3-4.) fig. 3-2 fig. 3-4 deflection yoke positioning corrects these areas. purity control corrects this area. disk magnets or rotatable disk magnets correct these areas (a-d). b c a d ba c d www.datasheet.co.kr datasheet pdf - http://www..net/
28 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 3-2. convergence preparation : ? before starting this adjustment, adjust the focus, horizontal size and vertical size. ? minimize the brightness setting. ? provide dot pattern. (1) horizontal and vertical static convergence (moving vertically), adjust the v.stat magnet so that the red, green and blue dots are on top of each other at the center of the screen. r g b g r b center dot c3 board rv 702 v.stat magnet h. stat vr 4 bmc (hexapole) magnet. if the red, green and blue dots are not balanced or aligned, then use the bmc magnet to adjust in the manner described below. 1 v. s tat 2 h. stat vr bmc (hexapole) v.stat purity v.stat bmc purity rg b r g b r gb rb rg g g b rb r r r r g g g g b b b b a a a b b b b r r g g b b a a b b b 3 www.datasheet.co.kr datasheet pdf - http://www..net/
29 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 (3) screen-corner convergence ba cd a-d : screen-corner misconvergence a d c b a to d : permalloy assembly fix a permalloy assy corresponding to the misconverged areas (2) dynamic convergence adjustment preparation: ? before starting this adjustment, adjust the horizontal static convergence and the vertical static convergence rb tlv ych b r on d y ych tlv www.datasheet.co.kr datasheet pdf - http://www..net/
30 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 3-3. focus adjustment adjust focus control on the flyback transformer for the best focus. flyback transformer (t503) 2. white balance adjustment 1) set to service mode (refer section 4-1: adjustments with commander). 2) input white raster signal. 3) set the picture to minimum. 4) select gct (whb 4) and bct (whb 5) with [1] and [4] , and adjust the level with [3] and [6] for the best white balance. 5) set the picture to maximum. 6) select gdr (whb 1) and bdr (whb 2) with [1] and [4] , and adjust the level with [3] and [6] for the best white balance. 7) write into the memory by pressing [muting] then [0] . 3. sub bright adjustment 1) set to service mode. 2) input a staircase signal of black to white from the pattern generator. 3) brightness .... 50%. picture ............ minimum 4) select sbr (whb7) with [1] and [4] , and adjust sbr (whb7) level with [3] and [6] so that the second stripe from the right is dimly lit. 3-4. g2 (screen) and white balance adjustments 1. g2 (screen) adjustment 1) set the picture to normal. 2) put to video input mode without signals. 3) connect r, g and b of the c3 board cathode to the oscillo- scope. 4) adjust brightness to obtain the cathode voltage to the value below. 5) adjust g2 (screen) on fbt until picture shows the point before cut-off. white second from the right black 0 v 175 v 2(vdc) focus screen www.datasheet.co.kr datasheet pdf - http://www..net/
31 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 section 4 circuit adjustments with the unit on standby [display] 5 vol (+) [power] this operation sequence puts the unit into service mode. 4-1. adjustments with commander service adjustments are made with the rm-952 that comes with this unit. a. entering service mode 1 , 4 select the adjustment item. 3 , 6 raise/lower the data value. [muting] writes. - executes the writing. 7 , - all the data becomes the values in memory. 8 , - all user control goes to the standard state. 5 , - service data initialization (be sure not to use usually.) 2 , - write 50hz adjustment data to 60hz, or vice versa. pal, secam : 50 ntsc : 60 00 hps 1c service data mode item name item no software version suffix no (oem code) total power-on time (hours) p marking of virgin nvm geo 1.0c 59 7f 000a 0 623s or 622s device name 50 tv 1 2 3 4 6 7 8 9 0 5 jump sound mode favorite progr b. method of cancellation from service mode set the standby condition (press [power] button on the commander), then press [power] button again, hereupon it becomes tv mode. c. method of write into memory 1) set to service mode. 2) press [1] (up) and [4] (down), select an item of adjustment. 3) press [muting] button and it will indicate write on the screen. 4) press [0] button to write into memory. d. memory write confirmation method 1) after adjustment, pull out the plug from ac outlet, and then plug into ac outlet again. 2) turn the power switch on and set to service mode. 3) call the adjusted items again to confirm adjustments were made. the screen display is : www.datasheet.co.kr datasheet pdf - http://www..net/
32 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 4-2. adjustment method item number 00 of device geo this explanation uses h-position as an example. 1. select ?eo 00 hps with the 1 and 4 buttons. 2. raise/lower the data with the 3 and 6 buttons. 3. select the optimum state. (the standard is 1f for pal reception.) 4. write with the [muting] button. (the display changes to write.) 5. execute the writing with the - button. (the write display will be changed to red color while excuting, and back to service.) use the same method for all items. use 1 and 4 to select the adjustment item, use 3 and 6 to adjust, write with [muting] , then execute the write with - . note : 1. in [write] , the data for all items are written into memory together. 2. for adjustment items that have different standard data between 50hz or 60hz, be sure to use the respective input signal after adjustment. 1f service 50 hps adjusted with [3] and [6] buttons. green written with [muting] write executed with [0] geo 00 7f 0 000a 59 623s or 622s 1.0c 1f service 50 hps red the write display then the display returns to a green service. geo 00 7f 0 000a 59 623s or 622s 1.0c 1f write 50 hps green geo 00 7f 0 000a 59 623s or 622s 1.0c www.datasheet.co.kr datasheet pdf - http://www..net/
33 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 adjustment item table category functionality micro data range function note for register slave ram address no. name init different data no. (bit) address (bit) geo 0 hps 7 3f h position 50/60hz 12 (7-2) cxa2130s(88h) 82 (7-2) 1 hsz 1f 3f h size 50/60hz 11 (7-2) 81 (7-2) 2 pap 1f 3f pin amp 50/60hz 13 (7-2) 83 (7-2) 3 tlt 7 0f trapezium 50/60hz 15 (7-4) 85 (7-4) 4 vps 1f 3f v position 50/60hz 0f (7-2) 7f (7-2) 5 vsz 1f 3f v size 50/60hz 0e (7-2) 7e (7-2) 6 sco 7 0f s correction 50/60hz 10 (7-4) 80 (7-4) 7 vln 7 0f v linearity 50/60hz 10 (3-0) 80 (3-0) 8 bow 7 0f afc bow 50/60hz 16 (7-4) 86 (7-4) 9 agl 7 0f afc-angle 50/60hz 16 (3-0) 86 (3-0) 10 upn 1f 3f upper pin 50/60hz 14 (7-2) 84 (7-2) 11 lpn 1f 3f lower pin 50/60hz 18 (7-2) 88 (7-2) 12 hbl 0 1 h blanking on/of f 18 (1) 67 (1) 13 lbl 7 0f left h blanking 50/60hz 17 (7-4) 87 (7-4) 14 rbl 7 0f right h blanking 50/60hz 17 (3-0) 87 (3-0) whb 0 rdr 2a 3f r drive dynamic/others 09 (7-2) cxa2130s(88h) 8f (7-2) 1 gdr 2a 3f g drive dynamic/others 0a (7-2) 90 (7-2) 2 bdr 2a 3f b drive dynamic/others 0b (7-2) 91 (7-2) 3 rct 7 0f r cutoff secam/others 07 (3-0) 93 (3-0) 4 gct 7 0f g cutoff secam/others 08 (7-4) 94 (7-4) 5 bct 7 0f b cutoff secam/others 08 (3-0) 94 (3-0) 6 bmn 15 1f brightness minimum data 97 7 sbr 28 3f sub brightness control 98 saj 0 pmx 33 3f picture maximum data cxa2130s(88h) 96 1 shu 8 0f sub hue control tv/video 99 2 ssh 3 0f sub sharpness control tv/video 9a 3 scl 1f 3f sub color control ntsc/others 9b vp 0 eht 4 0f eht comp 50/60hz 15 (3-0) cxa2130s(88h) 85 (3-0) 1 gma 2 03 gamma correction refer nvm map a4 0b (1-0) 1a3 (1-0) 2 ydl 6 0f y delay pal/secam/ntsc 0c (3-0) 8c (3-0) 3 sst 1 03 secam id start position 1b (1-0) 6a (1-0) 4 ssp 1 03 secam id stop position 1b (3-2) 6a (3-2) 5 slv 2 03 secam id level 1c (1-0) 6b (1-0) 6 sbf 22 3f secam bell fo 1c (7-2) 6b (7-2) 7 dyc 0 1 dynamic color on/of f 0a (1) 59 (1) 8 abl 1 1 abl mode switching standard always 0 09 (1) 58 (1) 9 vth 1 1 abl detection vth switching 09 (0) 58 (0) 10 sfo 1 1 fo switching for sharpness ntsc/others 05 (1) 198 (1) 11 dcx 1 1 dc trans. ratio switching 06 (1) 55 (1) 12 sht 1 1 pre-/overshoot ratio switch ntsc/others 06 (0) 199 (0) www.datasheet.co.kr datasheet pdf - http://www..net/
34 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 adjustment item table category functionality micro data range function note for register slave ram address no. name init different data no. (bit) address (bit) vp 13 hdw 0 1 h drive pulse width switch 00 (6) 4f (6) 14 afc 1 03 afc gain control tv/video/text 0f (1-0) 8d (1-0) 15 hos 7 0f h oscillation 0c (7-4) 5b (7-4) 16 hss 0 1 slice level of h sync sep. 0d (1) 5c (1) 17 vss 0 1 slice level of v sync sep. 0d (0) 5c (0) 18 hms 0 1 macro vision c/m off/on 50/60hz 0e (0) 7e (0) 19 yuv 0 1 yuv switch control 01 (0) 50 (0) 20 cdv 1 3 cd mode for video video only 0d (5-4) 1a1 (5-4) 21 ron 1 1 r on not memorized 01 (3) 50 (3) 22 gon 1 1 g on not memorized 01 (2) 50 (2) 23 bon 1 1 b on not memorized 01 (1) 50 (1) 24 pon 1 1 p on not memorized 00 (7) 4f (7) 25 blk 0 1 blk off 12 (0) 61 (0) 26 vmc 0 1 vm off 13 (0) 62 (0) ap 0 inf 0 3f input attenuation when surround of f 00 (5-0) tda7429 19f (5-0) 1 ins 0 3f input attenuation when surround on 1a0 (5-0) 2 ph1 0 3 phase 1 register selection 02 76 (1-0) 3 ph2 0 3 phase 2 register selection 76 (3-2) 4 ph3 0 3 phase 3 register selection 76 (5-4) 5 ph4 0 3 phase 4 register selection 76 (7-6) 6 bcs 2 3 bass center shift #4 (3-0) 1a8 (1-0) 7 tcs 2 3 treble center shift #5 (3-0) 1a9 (1-0) 8 trf 2 3 rf treble offset #5 (3-0) 1a9 (5-4) msp 0 wst 15 ff w/g stereo threshold msp3415d 157 (7-0) 1 wbt ea ff w/g bilingual threshold (84h) 158 (7-0) 2 wll 5 ff w/g monaural threshold 159 (7-0) 3 wac 0 0f w/g agreement count 15a (3-0) 4 wdl 30 ff w/g search delay 15b (7-0) 5 ndl 20 ff nicam search delay 15c (7-0) 6 sdl 10 ff stereo status read delay 15d (7-0) 7 agc 1 1 agc switch auto/constant bb (7) 108 (7) 8 rel 28 3f agc gain at constant mode bb (6-1) 108 (6-1) 9 crm 0 1 carrier muting on/of f bb (9) 107 (1) 10 aco 1 1 audio clock out on/of f 83 (5) 10c (5) 11 fp 1b 7f fm prescale for non-m system 0e (7-0) 16c (6-0) 12 fpm 32 7f fm prescale for m system 0e (7-0) 16d (6-0) 13 fh 36 7f fm prescale for hdev 0e (7-0) 16e (6-0) 14 fhm 65 7f fm prescale for hdev and m 0e (7-0) 16f (6-0) 15 wgp 2a 7f w/g prescale 0e (7-0) 170 (6-0) 16 nip 6d 7f nicam prescale 10 (7-0) 138 (6-0) 17 err 50 ff auto fm switch threshold 21 (10-3) 166 (7-0) 18 vol 6d ff loud speaker gain 7000h to 7f foh 0000 (15-4) 1a7 (7-0) www.datasheet.co.kr datasheet pdf - http://www..net/
35 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 category functionality micro data range function note for register slava ram address no. name init different data no. (bit) address (bit) txt 0 txh 1 3 teletext horizontal position (58h) 18d (1-0) 1 txv 0 3 teletext vertical position 18d (6-4) opm 0 osh 0a 3f osd h position option-misc ac (7-2) 1 com 0 03 comb selection a5 (7-6) 2 apc 1 1 apc switch a4 (5) 3 tsy 0 03 tv sys at auto tv sys a4 (4-3) 4 mut 0 1 no signal mute a4 (0) 5 afm 0 1 auto fm switch a4 (1) 6 rfb 0 3 c-bpf control a5 (5-4) 7 tv0 0 7 tilt to v-angle offset a5 (2-0) 8 dbl 0 1 disable blueback function a4 (2) opb 0 op1 ff ff optional bits 1 (see below) option-bits 45 1 op2 1 ff optional bits 2 (see below) 46 2 op3 0 ff optional bits 3 (see below) 47 adjustment item table note ? shaded items are fixed data. ? standard data listed on the adjustment item table are reference values, therefore it may be dif ferent for each model and for each mode. ? note for different data those are the standard data values written on the microprocessor . therefore, the data values of the modes and stored respectively in the memory. in case of a device replacement, adjustment by rewriting the data value is necessary for some items. www.datasheet.co.kr datasheet pdf - http://www..net/
36 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 av input item kv-pf21l70 kv-pf21m40 kv-pf21m70 (e) kv-pf21m70 (me) kv-pf21p10 KV-PF21P40 (singapore) KV-PF21P40 (malaysia) kv-pf21p41 kv-pf21q70 m 0 1 1 1 0 0 0 0 0 d/k 0 1 1 1 0 0 0 0 0 i 0 1 1 1 0 0 0 0 0 b/g 1 1 1 1 1 1 1 1 1 2nd. lang 1 1 1 1 1 1 1 1 1 secam 1 1 1 1 0 0 0 0 1 xtal 3.58 1 1 1 1 1 1 1 1 0 xtal 4.43 1 1 1 1 1 1 1 1 1 item information. no. opb0 op1 no. opb1 op2 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 dvd input 0 0 0 0 0 0 0 0 0 dis fav. 1 1 1 1 1 1 1 1 1 thai bil 0 0 0 0 0 0 0 0 0 hdev 0 0 0 0 0 0 0 0 0 nicam 0 0 0 0 0 0 0 0 0 top 0 0 0 0 0 0 0 0 0 item kv-pf21l70 kv-pf21m40 kv-pf21m70 (e) kv-pf21m70 (me) kv-pf21p10 KV-PF21P40 (singapore) KV-PF21P40 (malaysia) kv-pf21p41 kv-pf21q70 no. opb2 op3 color sw 1 1 1 1 1 1 1 1 1 11 key 0 0 0 0 0 0 0 0 0 av mono 1 1 1 1 1 1 1 1 1 us st 0 0 0 0 0 0 0 0 0 auto tv sys 0 0 0 0 0 0 0 0 0 auto pic 1 1 1 1 1 1 1 1 1 2199 curve 0 0 0 0 0 0 0 0 0 pic rot 0 0 0 0 0 0 0 0 0 item kv-pf21l70 kv-pf21m40 kv-pf21m70 (e) kv-pf21m70 (me) kv-pf21p10 KV-PF21P40 (singapore) KV-PF21P40 (malaysia) kv-pf21p41 kv-pf21q70 www.datasheet.co.kr datasheet pdf - http://www..net/
37 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 sub hue adjustment 1. select video 1. 2. input a ntsc color-bar, video into video 1. 3. set the following condition: picture 100%, brightness 50%, color 50% 4. connect an oscilloscope to pin 1 (b out) of cn305, a board. 5. select saj 1 ?hu?with 1 and 4 of the commander by set- ting to service mode and adjust to vb1=vb2=vb3=vb4 with 3 and 6 . 4-3. picture quality adjustments sub color adjustment 1. input a pal color-bar. 2. set to the following condition: picture 100%, brightness 50%, color 50% 3. connect an oscilloscope to pin 1 (b out) of cn305, a board. 4. set to service mode and select saj 3 ?cl with 1 and 4 of the commander then adjust to vb2=vb3=vb4 with 3 and 6 . 5. press [muting] - of the commander to write the data. 6. adjust saj 3 ?cl as step 2 to 5 when receiving ntsc color- bar. vb1 vb2 vb3 vb4 vb2 = vb3 = vb4 6. press [muting] - of the commander to write the data. vb1 vb2 vb3 vb4 vb1 = vb2 = vb3 = vb4 bell filter adjustment 1. input secam color-bar signal. 2. connect the dual-trace oscilloscope to the pin 9 (r-y) of cn303 (not mounted). 3. adjust service mode, items ?bf as shown below. 4-4. a board adjustment after ic003 (memory) replacement when replacing ic003 (memony), be sure to change ic001 (?com) to the following new ic at the same time. ic001 (?con) : cxp86461-622s (for me) : cxp86461-623s (except me) 1. enter to service mode. 2. press commander buttons 5 and - (data initialize), and 2 and - (data copy) to initialize the data. 3. call each item number and check if the respective screen shows the normal picture. in cases where items are not well adjusted, rectify the items with fine adjustment. write the data per each item number ( [muting] + - ). 4. select item numbers ?pb0?(op1), ?pb1?(op2) and ?pb2 (op3) and respectively set the bit per model with command buttons 3 and 6 . 5. press commander buttons 8 and - (test normal) to return to the data that was set on the shipment from the factory. (this will also cancel service mode.) www.datasheet.co.kr datasheet pdf - http://www..net/
38 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 4-5. picture distortion adjustment item number 00 ?0b geo 0 hsh (h position) geo 1 hsz (h size) geo 2 pap (pin amp) geo 5 vsz (v size) geo 7 vln (v linearity) geo 4 vsh (v position) geo 6 scr (vertical s-correction) geo 8 vbow (afc.bow) geo 9 agl (afc.angle) geo 3 tilt (trapezium) geo 0a ucp (upper corner pin) geo 0b lcp (lower corner pin) www.datasheet.co.kr datasheet pdf - http://www..net/
39 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 memo www.datasheet.co.kr datasheet pdf - http://www..net/
40 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 memo www.datasheet.co.kr datasheet pdf - http://www..net/
section 5 diagram 5-1. block diagram ? 42 ? 43 ? 41 yc jungle ic301 cxa2130s monitor out tv v in tv l in tv r in mon out tv v in v1 v in 43 6 12 v1 v in v1 l in v2 v in v2 v in 4 v2 l in v out 2 l out 2 jack block video in 1 audio prosessor ic203 tda7429s audio out ic201 ta8248k red out green out blue out q704-712 c3 sp assy (this is not used for these models) r out crt socket g out crt a51lpt70x dy y21rsa-s b out r out v out u out y out v in u in y in g out b out 22 23 24 21 19 18 11 13 14 ik in h. drive h. pulse e/w vd+ vd- h-out q511 2sd2578 v-out ic503 tda8172 hdt t501 h-drive q506 2sd774-34 pin-cont ic502 njm2903m pin-out q505 irf614 pmc l509 hlc l510 fbt t503 nx-1748 +b audio front vcc +9v 11v 7v +5v 5v reg & reset ic002 mm1319af 9v rec ic603 5v rec ic604 stb trans t604 srt t603 additional color matrix system ucom ic001 cxp86449 receiver sbx1981-51 ic901 sircs r g b blk i2l memory ic003 m24c08-bn6 32 31 30 37 39 40 28 29 30 31 f stb sw tr q605 2sk2845 power ic ic601 str-f6654 line filter t601 line filter t4601 t4602 thp thp600 ac cord dgc main. tuvif tu101 btf-lg411(i) (except kv-pf21m40/ pf21m70)(e/me) btf-lg433(i) (kv-pf21m40/pf21m70) (e/me) j401 video in 2 (front) j902 text decoder with ucom ic801 saa5261 (kv-pf21p41 only) v1 r g b blk 4p 2p kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 www.datasheet.co.kr datasheet pdf - http://www..net/
cn604 cn703 dy1 dgc b 9v ik 1 5 6 (rgb out) 1 e cn704 picture tube 1 2 3 4 5 6 h+ h+ h- h- v- v+ (power supply, hv, micon, y/c jungle) 1 2 3 dgc nc dgc 2 1 ac in ac in a c3 dy assy cn702 1 g2 fbt 4 3 gnd r h1 3 2 1 e 200v cn701 2g 9v ik gnd r g b 6 5 4 3 2 1 cn305 1 2 3 h1 gnd 200v cn505 cn601 crt cn4602 ac out ac out 2 1 ac in ac in 2 1 cn4601 (cispr) f 1 gnd cn4603 cn104 gnd 1 red green blue blk gnd sda scl 7 6 5 4 3 2 1 cn307 cn301 1 2 3 7 gnd vp scp 7v cvbs gnd 6 5 gnd 4 cn801 7.5v cvbs gnd gnd scp vp gnd 7 6 5 4 3 2 1 cn803 1 2 3 4 5 6 7 red green blue blk gnd sda scl (kv-pf21p41 only) v1 (tele text) v1 (kv-pf21p41 only) a f c3 5-3. circuit boards location ? 46 ? 44 ? 45 5-2. frame schematic diagram kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 www.datasheet.co.kr datasheet pdf - http://www..net/
?47 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 5-4. schematic diagrams and printed wiring boards note: ? all capacitors are in f unless otherwise noted. ? all electrolytic capacitors are rated at 50v unless otherwise noted. ? all resistors are in ohms. k ? = 1000 ? , m ? = 1000k ? ? indication of resistance which does not have rating electrical power is as follows. pitch: 5 mm rating electrical power 1/4w (chip: 1/10w) ? : nonflammable resistor. ? : internal component. ? : panel designation or adjustment for repair. ? all variable and adjustable resistors have characteristic curve b unless otherwise noted. ? readings are taken with a color-bar signal input. no mark : pal ( ) : secam [ ] : ntsc 3.58 : ntsc 4.43 ? readings are taken with a 10 m ? digital multimeter. ? voltage are dc with respect to ground unless other- wise noted. ? voltage variations may be noted due to normal pro- duction tolerances. ? all voltages are in v. ? : cannot be measured. ? circled numbers are waveform references. ? : b + bus. ? : b ?bus. ? : signal path. reference information resistor : rn metal film : rc solid : fprd nonflammable carbon : fuse nonflammable fusible : rs nonflammable metal oxide : rb nonflammable cement : rw nonflammable wirewound : * adjustment resistor coil : lf-8l micro inductor capacitor : ta tantalum : ps styrol : pp polypropylene : pt mylar : mps metalized polyester : mpp metalized polypropylene : alb bipolar : alt high temperature : alr high ripple note: the component identified by shading and mark ! are critical for safety. replace only with part number specified. * www.datasheet.co.kr datasheet pdf - http://www..net/
?48 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 5 8 2 6 2 2 3 8 8 8 int0 int1 int2 tex tx extal xtal rst mp v dd v ss rmc an0~an5 6 pa0~pa7 port a port b port c port d port e port f port g pb0~pb7 pc0~pc5 pc6~pc7 pd0~pd7 pe0~pe1 pe2~pe3 pe4~pe6 pf0~pf7 pg3~pg6*, pg7 s1 so sck sda0 sda1 scl0 scl1 pwm adj pwm0~pwm7 (pwm0~pwm5) i 2 c bus interface unit 8-bit pwm 8ch (6ch) 14bit pwm 1ch on screen display 8-bit timer/ counter 0 serial interface unit remocon fifo a/d converter 6ch spc700 cpu core rom 12k/16k/24k/32k 40k/48k/60k bytes prescaler/ time-base timer watchdog tmer 32khz timer/counter ram 352/704/1536 bytes clock generator /system control interrupt controller 8-bit timer 1 hsync counter 1 hsync counter 0 8(6) ec xlc exlc r g b i ys ym hsync vsync hs0 hs1 to 2 2 2 a board ic001 cxp86461-622s (for me) a board ic001 cxp86461-623s (except me) www.datasheet.co.kr datasheet pdf - http://www..net/
kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 57 58 59 60 4.8vp-p (v) 5.0vp-p (v) 1.0vp-p (h) 194vp-p 110vp-p 1.2vp-p (h) 0.9vp-p (h) pal/secam 3.2vp-p (h) 3.2vp-p (h) ntsc 1.4vp-p (h) 3.2vp-p (h) 1 2 34 6 5 6 7 8 11 12 12 13 14 15 1.2vp-p (h) 4.4vp-p (v) 10 9 1.4vp-p (h) 16 1.5vp-p (v) pal/secam ntsc 1.0vp-p (h) 3.5vp-p 0.9vp-p (v) pal/secam ntsc 4 1.2vp-p (h) note: the circuit indicated at left contains high voltage of over 600 vp-p. please pay attention when inspecting or repairing it to prevent an electric shock. a board ic ic001 b-10 ic002 c-9 ic003 a-9 ic100 b-5 ic201 b-11 ic203 c-3 ic204 b-2 ic301 b-6 ic502 e-6 ic503 j-5 ic601 i-8 ic602 h-6 ic603 d-8 ic604 d-10 ic901 i-13 ph600 h-7 q001 b-8 q002 b-8 q003 c-9 q004 c-9 q101 a-4 q201 a-11 q202 a-11 q203 c-11 q204 c-11 q205 a-12 q206 a-11 q207 a-11 q301 b-8 q302 a-6 q303 a-6 q304 b-6 q305 b-5 q306 b-5 q307 c-7 q308 c-7 q309 c-7 q310 d-7 q311 d-9 q312 b-7 q313 b-8 q315 b-5 q401 d-2 q402 d-1 q403 d-2 q404 c-3 q501 d-6 q502 e-7 q503 f-6 q505 d-6 q506 d-2 q507 h-6 q509 f-6 q511 f-1 q600 c-12 q601 f-11 q602 j-7 q603 i-7 q604 h-6 q605 e-12 q606 f-11 q607 h-13 q901 h-13 q902 h-13 diode d001 b-8 d002 c-8 d003 c-9 transistor d004 d-8 d005 b-8 d006 a-3 d203 c-11 d300 a-9 d301 b-9 d302 b-6 d303 b-5 d304 b-5 d305 b-5 d306 c-5 d307 c-5 d308 b-5 d309 b-6 d310 a-6 d311 c-6 d312 c-6 d313 a-8 d315 b-7 d316 c-7 d317 b-9 d314 a-9 d319 c-6 d320 c-6 d321 b-6 d401 d-2 d402 c-3 d403 b-1 d404 c-2 d405 c-1 d406 b-1 d407 c-2 d408 c-1 d409 a-1 d504 d-5 d505 h-6 d506 f-6 d507 f-6 d508 i-5 d509 e-6 d510 f-5 d511 f-5 d512 g-5 d513 i-5 d517 f-2 d518 f-2 d519 f-2 d520 e-5 d521 i-4 d522 j-4 d525 f-5 d526 f-6 d527 f-3 d528 f-3 d529 f-5 d530 f-2 d531 e-6 d532 e-6 d533 d-2 d534 e-6 d600 g-13 d601 i-8 d602 g-13 d603 f-11 d604 j-7 d605 g-10 d606 e-11 d607 f-10 d608 e-11 d609 h-8 d610 j-8 d611 i-7 d612 f-8 d613 i-7 d614 h-7 d615 e-7 d616 e-9 d617 f-8 d618 f-9 d620 d-8 d621 f-8 d622 f-7 d623 f-12 d624 f-12 d625 d-12 d627 f-8 d628 g-5 d629 f-9 d630 e-9 d631 g-12 d632 f-12 d633 e-12 d634 f-11 d635 f-12 d636 d-12 d637 f-11 d638 e-11 d901 c-13 d902 d-13 d903 c-13 d904 d-13 d905 f-13 d906 i-13 a board waveforms printed wiring board a [power supply, hv, micon, y/c jungle] C a board C a board ? mark list a 123456789101112 13 b c d d e f g h i note) the parts indicated as # in this circuit diagram are not listed here, as they are not used in this models. kv-pf21l70 kv-pf21m40 kv-pf21m70 kv-pf21m70 kvpf21p10 kv-pf21m40 pf21p40 kv-pf21p41 kv-pf21q70 (me) (ge) (e) (me) (oce) (singapore) (malaysia) (malaysia) (me) c307 18p :chip 18p :chip 18p :chip 18p :chip 18p :chip 18p :chip 18p :chip 18p :chip # c622 0.0015 # # 0.0015 0.0015 0.0015 0.0015 # 0.0015 c624 1500p 2kv # # 1500p 2kv 1500p 2kv 1500p 2kv 1500p 2kv # 1500p 2kv cn 301# ##### #7p # cn 307# ##### #7p # ic 001 cxp86449-622s cxp86449-623s cxp86449-623s cxp86449-622s cxp86449-623s cxp86449-623s cxp86449-623s cxp86449-623s cxp86449-622s r 375# ##### # chip 100 # tu 101 btf-lg411 btf-lg433 btf-lg433 btf-lg433 btf-lg411 btf-lg411 btf-lg411 btf-lg411 btf-lg411 x 302 ctystal ctystal ctystal ctystal ctystal ctystal ctystal ctystal # www.datasheet.co.kr datasheet pdf - http://www..net/
?62 ?63 ?61 ?64 pa l 25vp-p (h) 89vp-p (h) ntsc 3.58 ntsc 4.43 75vp-p (h) 4 2 2 2 12 3 secam 93vp-p (h) pal/secam : ntsc : 86vp-p (h) 95vp-p (h) 80vp-p (h) 90vp-p (h) f (cispr) c3 (rgb out) a b c d e f g h i 12345678910111213141516 17 18 19 20 21 22 c3 board waveforms C f board C f [cispr] C c 3 board C [rgb out] schematic diagrams c 3 f boards / (3) schematic diagrams of c3 and f boards printed wiring board c 3 www.datasheet.co.kr datasheet pdf - http://www..net/
66 65 67 a b c d e f g h i 123456789101112131415 (4) schematic diagrams of v1 board printed wiring board [tele text] C v 1 board C (kv-pf21p41 only) v 1 v 1 (tele text) ! schematic diagram ? v 1 board www.datasheet.co.kr datasheet pdf - http://www..net/
?69 ?68 ?70 2sd2144s-uvw 2sc2611 transistor e b c e c b letter side e c b e c b b c e 5-5. semiconductors diode cathode anode cathode anode gate 3 1 2 1 3 2 1 1 2 2 3 3 cathode anode cathode anode cathode anode ic 1 top view dual in-line package pin 6 ~ 98 2 1 3 4 1 4 3 3 1 2 1 3 2 3 1 2 1 3 2 spb-26mvwf led cathode anode single in -line package pin 6 ~ 98 1 top view zig-zag in -line package pin 6 ~ 99 marking side view 1 39 40 26 52 14 27 113 marking side view 1 n au-01z-v1 el1z gp08d rd33eb3t rgp02-17el-6433 d4sb60l erc04-06se rn4z rs 3fs 31dq06-fc5 erd29-08j on3171-r d1ns4 rd1.1es-l2 rd20es-b2 rd30esb2 rd6.8es-b1 1ss119-25 11eqs04 11es2-nta2b dtz-tt11-15b dtz-10b ma 111-(k8).so udzs-te17-5.1b udzs-te17-6.8b 1ss355te-17 5p6m da204k fmu-g26s cathode anode rd3.3m-b2 rd5.6m-b2 eg01cv0 dap020k cathode anode (grn) anode (grn) dtc114ek un2111 un2211 un2213 un2216 2sc1623-l5l6 2sc2712-yg 2sc2785-hfe 2sa1091-o 2sd2394-ef e letter side c b cxa2130s (64pin) cxp86449-622s (64pin) cxp86449-623s (64pin) tda7429s (42pin) mm1319afbe (7pin) njm2903m (8pin) njm78m09fa ta7805s sbx1981-51 se-135n tda8172 str-f6654 ru-1p \ ta8248k kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 www.datasheet.co.kr datasheet pdf - http://www..net/
kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 1 x-4036-748-2 beznet assy (kv-pf21p41) 3,28,33 x-4036-758-1 beznet assy (kv-pf21l70) 3,28,33 x-4036-758-3 beznet.assy (kv-pf21q70) 3,28,33 x-4036-748-1 beznet.assy (kv-pf21m40/ pf21m70) 3,28,33 x-4036-748-3 beznet.assy (kv-pf21p10/pf21p40) 3,28,33 2 4-070-291-01 button, power (kv-pf21m40) 4-070-291-11 button, power (kv-pf21l70/ pf21q70/pf21m70/pf21p10/pf21p40) 3 4-070-290-01 button, multi (except kv-pf21q70) 4-070-290-11 button, multi (kv-pf21q70) 4 1-505-740-11 speaker (5x9cm) 5 4-054-981-01 screw, step tapping 6 4-365-808-01 screw (5), tapping 7 4-046-600-11 spacer, dy 8 * 3-704-372-11 holder, hv cable (except kv-pf21p10) 9 ! 8-738-812-05 picture tube (a51lpt70x) (kv-pf21m40/pf21p40/pf21p41) ! 8-738-809-05 picture tube (a51lpt70x) (kv-pf21l70/pf21m70/pf21p10/pf21q70) 10 8-451-505-11 deflcetion yoke (y21rsa-s) (except kv-pf21p10) ! 8-451-505-11 deflcetion yoke (y21rsa-s) (kv-pf21p10) 11 * a-1331-884-a c3 board, mounted 12 4-369-318-61 spring, tension 13 ! 1-416-946-21 coil, demagnetic 14 * 4-067-189-01 pwb(l), guide 15 * 4-067-187-01 pwb(r), guide 16 * 8-598-447-00 tuner, fss btf-lg411 (except kv-pf21m40/m70) * 8-598-447-10 tuner, fss btf-lg433 (kv-pf21m40/m70) 17 ! * 1-453-293-11 transformer assy, flyback (nx-1748//m3a4) (except kv-pf21m70(me)) ! 1-453-298-11 transformer assy, flyback (nx-1748//m3a4) (kv-pf21m70(me)) section 6 exploded view note: ? items with no part number and no description are not stocked because they are seldom required for routine service. ? the construction parts of an assembled part are indicated with a collation number in the remark column. 6-1. chassis [ : bvtp 3 12 7-685-648-79 l : bvtp 4 16 7-685-663-71 the components identified by shading and mark ! are critical for safety. replace only with part number specified. ? items marked " * " are not stocked since they are seldom required for routine service. some delay should be anticipated when ordering these items. ?71 ?72 ref. no. part no. description remark 4 31 22 25 23 6 5 32 7 19 12 30 29 13 12 11 10 9 6 26 1 28 14 15 2 18 27 34 16 20 21 24 17 3 33 35 8 18 * a-1299-010-a a board, complete (kv-pf21p41) a-1298-989-a a board, complete (kv-pf21p10/ p40(malaysia) a-1298-979-a a board, complete (kv-pf21l70) a-1298-978-a a board, complete (kv-pf21q70) a-1298-996-a a board, complete (kv-pf21m70(me)) a-1298-975-a a board, complete (KV-PF21P40(singapore) a-1299-009-a a board, complete (kv-pf21m40) a-1299-007-a a board, complete (kv-pf21m70(e)) 19 4-057-714-01 piece assy, tlh correction 20 4-022-115-00 holder, ac cord 21 ! 1-574-062-11 cord, power (with connector) 2.5a/250v (except kv-pf21p10) ! 1-574-358-11 cord, power (with connector) 7.5a/250v (kv-pf21p10) 22 1-452-032-00 magnet,disc 23 4-051-736-21 piece a(90), conv. correct 24 4-067-167-21 bracket,terminal 25 1-452-094-00 circular disc magnet b 26 4-069-651-02 blotting sheet (except kv-pf21l70/q70) 4-069-651-01 blotting sheet (kv-pf21l70/q70) 27 * a-1241-355-a f board, mounted 28 x-4036-750-2 door assy, control (kv-pf21p41) x-4036-753-1 door assy, control (kv-pf21l70) x-4036-750-1 door assy, control (kv-pf21m40/m70) x-4036-753-3 door assy, control (kv-pf21q70) 29 ! 4-070-300-01 cover, rear 30 4-064-883-11 holder, dgc 31 * 4-379-189-11 cushion, speaker 32 4-069-652-02 cushion (hs band) 33 * 4-070-292-01 bar, optical 34 * a-1347-155-a v1 board, complete (kv-pf21p41 only) 35 * 4-068-953-02 bracket, v1 (kv-pf21p41 only) 36 3-704-372-11 holder, hv cabe (kv-pf21p10) ref. no. part no. description remark note : the picture tube for oce model is upside down, and the positon for the anode cap and tension springs are changed accordingly. www.datasheet.co.kr datasheet pdf - http://www..net/
kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 ref. no. part no. description remark the components identified by shading and mark ! are critical for safety. replace only with part number specified. ref. no. part no. description remark ref. no. part no. description remark the components identified by shading and mark ! are critical for safety. replace only with part number specified. ref. no. part no. description remark 73 74 * a-1298-979-a a board complete (kv-pf21l70) ********************* * a-1299-009-a a board complete (kv-pf21m40) ********************* * a-1299-007-a a board complete (kv-pf21m70(e)) ********************* * a-1298-996-a a board complete (kv-pf21m70(me)) ********************* * a-1298-989-a a board complete (kv-pf21p10/pf21p40(malaysia)) ***************** * a-1298-975-a a bo ard complete (KV-PF21P40(singapore)) ******************** * a-1299-010-a a board complete (kv-pf21p41) ******************** * a-1298-978-a a board complete (kv-pf21q70) ********************* * 4-055-304-01 holder, led * 4-067-182-02 holder, fbt 4-382-854-11 screw (m3x10), p, sw (+) 4-382-854-21 screw (m3x14), p, sw (+) 7-685-648-79 screw +bvtp 3x12 type2 it-3 < c003 1-163-251-11 ceramic chip 100pf 5% 50v c004 1-163-001-11 ceramic chip 220pf 10% 50v c005 1-163-001-11 ceramic chip 220pf 10% 50v c006 1-164-004-11 ceramic chip 0.1mf 10% 25v c007 1-104-664-11 elect 47mf 20% 16v c008 1-163-251-11 ceramic chip 100pf 5% 50v c010 1-163-251-11 ceramic chip 100pf 5% 50v c012 1-163-251-11 ceramic chip 100pf 5% 50v c013 1-163-021-91 ceramic chip 0.01mf 10% 50v c014 1-104-664-11 elect 47mf 20% 25v c015 1-163-009-11 ceramic chip 0.001mf 10% 50v c016 1-163-113-00 ceramic chip 68pf 5% 50v c017 1-163-113-00 ceramic chip 68pf 5% 50v c019 1-104-664-11 elect 47mf 20% 25v c022 1-163-227-11 ceramic chip 10pf 0.5pf 50v c023 1-163-227-11 ceramic chip 10pf 0.5pf 50v c024 1-163-227-11 ceramic chip 10pf 0.5pf 50v c026 1-164-004-11 ceramic chip 0.1mf 10% 25v c027 1-164-004-11 ceramic chip 0.1mf 10% 25v c028 1-163-037-11 ceramic chip 0.022mf 10% 50v c030 1-126-965-11 elect 22mf 20% 50v c031 1-164-004-11 ceramic chip 0.1mf 10% 25v c032 1-107-823-11 ceramic chip 0.47mf 10% 16v c034 1-163-031-11 ceramic chip 0.01mf 50v c041 1-163-251-11 ceramic chip 100pf 5% 50v ref.no. part no. description remark ref.no. part no. description remark c042 1-163-251-11 ceramic chip 100pf 5% 50v c043 1-163-251-11 ceramic chip 100pf 5% 50v c044 1-163-251-11 ceramic chip 100pf 5% 50v c047 1-163-251-11 ceramic chip 100pf 5% 50v c048 1-163-251-11 ceramic chip 100pf 5% 50v c050 1-163-251-11 ceramic chip 100pf 5% 50v c051 1-163-251-11 ceramic chip 100pf 5% 50v c053 1-163-251-11 ceramic chip 100pf 5% 50v c054 1-163-251-11 ceramic chip 100pf 5% 50v c055 1-163-251-11 ceramic chip 100pf 5% 50v c103 1-164-004-11 ceramic chip 0.1mf 10% 25v c104 1-104-665-11 elect 100mf 20% 10v c107 1-163-005-11 ceramic chip 470pf 10% 50v c108 1-104-664-11 elect 47mf 20% 16v c109 1-163-005-11 ceramic chip 470pf 10% 50v c110 1-163-005-11 ceramic chip 470pf 10% 50v c111 1-163-005-11 ceramic chip 470pf 10% 50v c112 1-104-664-11 elect 47mf 20% 16v c113 1-104-664-11 elect 47mf 20% 25v c114 1-126-967-11 elect 47mf 20% 50v c202 1-163-021-91 ceramic chip 0.01mf 10% 50v c204 1-130-481-00 mylar 0.0068mf 5% 50v c206 1-164-182-11 ceramic chip 0.0033mf 10% 50v c209 1-126-964-11 elect 10mf 20% 50v c210 1-126-933-11 elect 100mf 20% 16v c211 1-126-941-11 elect 470mf 20% 25v c212 1-126-933-11 elect 100mf 20% 16v c215 1-126-942-61 elect 1000mf 20% 25v c216 1-163-021-91 ceramic chip 0.01mf 10% 50v c218 1-136-167-00 film 0.15mf 5% 50v c220 1-126-942-61 elect 1000mf 20% 25v c221 1-126-964-11 elect 10mf 20% 50v c223 1-126-965-11 elect 22mf 20% 50v c224 1-163-133-00 ceramic chip 470pf 5% 50v c226 1-109-982-11 ceramic chip 1mf 10% 10v c227 1-163-037-11 ceramic chip 0.022mf 10% 50v c228 1-163-024-00 ceramic chip 0.018mf 10% 50v c229 1-163-018-00 ceramic chip 0.0056mf 10% 50v c230 1-163-024-00 ceramic chip 0.018mf 10% 50v c231 1-163-018-00 ceramic chip 0.0056mf 10% 50v c232 1-163-037-11 ceramic chip 0.022mf 10% 50v c233 1-164-004-11 ceramic chip 0.1mf 10% 25v c234 1-164-004-11 ceramic chip 0.1mf 10% 25v c235 1-164-004-11 ceramic chip 0.1mf 10% 25v c236 1-164-004-11 ceramic chip 0.1mf 10% 25v c238 1-164-505-11 ceramic chip 2.2mf 16v c240 1-164-505-11 ceramic chip 2.2mf 16v section 7 electrical parts list note: the components identified by shading and mark ! are critical for safety. replace only with part number specified. when indicating parts by reference number, please include the board name. ? all resistors are in ohms ? f : nonflammable capacitors ? mf : f, pf : ? f coils ? mmh : mh, uh : h ? items marked " ? " are not stocked since they are seldom required for routine service. some delay should be anticipated when or- dering these items. ? all variable and adjustable resistors have characteristic curve b, unless otherwise noted. a c241 1-164-346-11 ceramic chip 1mf 16v c242 1-164-505-11 ceramic chip 2.2mf 16v c243 1-216-295-91 short 0 c244 1-164-700-11 ceramic chip 0.68mf 16v c245 1-164-346-11 ceramic chip 1mf 16v c246 1-163-018-00 ceramic chip 0.0056mf 10% 50v c248 1-163-010-11 ceramic chip 0.0012mf 10% 50v c249 1-164-004-11 ceramic chip 0.1mf 10% 25v c251 1-163-017-00 ceramic chip 0.0047mf 10% 50v c252 1-164-346-11 ceramic chip 1mf 16v c253 1-163-037-11 ceramic chip 0.022mf 10% 50v c254 1-126-965-11 elect 22mf 20% 50v c255 1-163-037-11 ceramic chip 0.022mf 10% 50v c256 1-164-004-11 ceramic chip 0.1mf 10% 25v c259 1-126-933-11 elect 100mf 20% 16v c265 1-164-505-11 ceramic chip 2.2mf 16v c301 1-126-935-11 elect 470mf 20% 16v c302 1-163-005-11 ceramic chip 470pf 10% 50v c303 1-126-964-11 elect 10mf 20% 50v c304 1-126-967-11 elect 47mf 20% 50v c305 1-164-004-11 ceramic chip 0.1mf 10% 25v c306 1-163-233-11 ceramic chip 18pf 5% 50v c307 1-163-233-11 ceramic chip 18pf 5% 50v (except kv-pf21q70) c308 1-163-259-91 ceramic chip 220pf 5% 50v c309 1-126-957-11 elect 0.22mf 20% 50v c310 1-126-963-11 elect 4.7mf 20% 50v c311 1-126-964-11 elect 10mf 20% 50v c312 1-164-346-11 ceramic chip 1mf 16v c313 1-164-346-11 ceramic chip 1mf 16v c315 1-164-004-11 ceramic chip 0.1mf 10% 25v c316 1-104-664-11 elect 47mf 20% 25v c317 1-164-004-11 ceramic chip 0.1mf 10% 25v c318 1-163-031-11 ceramic chip 0.01mf 50v c319 1-163-031-11 ceramic chip 0.01mf 50v c320 1-163-031-11 ceramic chip 0.01mf 50v c322 1-163-005-11 ceramic chip 470pf 10% 50v c324 1-163-017-00 ceramic chip 0.0047mf 10% 50v c325 1-126-960-11 elect 1mf 20% 50v c327 1-126-965-11 elect 22mf 20% 50v c328 1-164-004-11 ceramic chip 0.1mf 10% 25v c330 1-164-004-11 ceramic chip 0.1mf 10% 25v c332 1-126-963-11 elect 4.7mf 20% 50v c335 1-164-004-11 ceramic chip 0.1mf 10% 25v c336 1-164-004-11 ceramic chip 0.1mf 10% 25v c337 1-126-961-11 elect 2.2mf 20% 50v c338 1-163-017-00 ceramic chip 0.0047mf 10% 50v c341 1-115-340-11 ceramic chip 0.22mf 10% 25v c342 1-163-259-91 ceramic chip 220pf 5% 50v c402 1-164-346-11 ceramic chip 1mf 16v c404 1-163-005-11 ceramic chip 470pf 10% 50v c405 1-126-935-11 elect 470mf 20% 16v c407 1-164-346-11 ceramic chip 1mf 16v c408 1-163-133-00 ceramic chip 470pf 5% 50v c409 1-126-963-11 elect 4.7mf 20% 50v c502 1-163-145-00 ceramic chip 0.0015mf 5% 50v c506 1-107-638-11 elect 33mf 20% 160v c507 1-161-830-00 ceramic 0.0047mf 500v c510 1-102-112-00 ceramic 330pf 10% 50v c512 1-163-989-11 ceramic chip 0.033mf 10% 25v c513 1-163-263-11 ceramic chip 330pf 5% 50v c514 1-106-383-00 mylar 0.047mf 10% 200v c517 1-164-182-11 ceramic chip 0.0033mf 10% 50v c518 1-104-665-11 elect 100mf 20% 10v c519 1-102-212-00 ceramic 820pf 10% 500v c521 1-126-934-11 elect 220mf 20% 16v c522 1-126-933-11 elect 100mf 20% 16v c523 1-102-002-00 ceramic 680pf 10% 500v c524 1-126-967-11 elect 47mf 20% 50v c526 1-130-495-00 mylar 0.1mf 5% 50v c527 1-102-820-00 ceramic 330pf 5% 50v c528 1-162-134-11 ceramic 470pf 10% 2kv c530 1-137-372-11 film 0.022mf 5% 50v c531 1-126-961-11 elect 2.2mf 20% 50v c532 1-126-941-11 elect 470mf 20% 25v c533 1-126-941-11 elect 470mf 20% 25v c536 1-136-165-00 film 0.1mf 5% 50v c537 1-126-969-11 elect 220mf 20% 50v c538 1-136-076-00 film 0.0085mf 3% 2kv c539 1-129-746-91 film 0.039mf 5% 400v c540 1-136-171-00 film 0.33mf 5% 50v c546 1-165-319-11 ceramic chip 0.1mf 50v c549 1-163-017-00 ceramic chip 0.0047mf 10% 50v c550 1-106-220-00 mylar 0.1mf 10% 100v c551 1-126-960-11 elect 1mf 20% 50v c552 1-162-116-00 ceramic 680pf 10% 2kv c553 1-162-116-00 ceramic 680pf 10% 2kv c554 1-137-417-11 mylar 0.0047mf 10% 200v c556 1-126-941-11 elect 470mf 20% 25v c557 1-126-941-11 elect 470mf 20% 25v c558 1-123-024-21 elect 33mf 160v c560 1-102-228-00 ceramic 470pf 10% 500v c561 1-136-557-11 film 0.0033mf 5% 630v c562 1-102-228-00 ceramic 470pf 10% 500v c564 1-163-038-91 ceramic chip 0.1mf 25v c565 1-107-655-11 elect 47mf 20% 250v c566 1-102-244-00 ceramic 220pf 10% 500v c567 1-115-521-11 film 0.82mf 5% 250v c568 1-102-228-00 ceramic 470pf 10% 500v c570 1-115-520-11 film 0.68mf 5% 250v c573 1-106-379-12 mylar 0.033mf 10% 200v c574 1-107-636-11 elect 10mf 20% 160v c576 1-130-495-00 mylar 0.1mf 5% 50v c577 1-106-395-00 mylar 0.15mf 10% 200v c582 1-164-004-11 ceramic chip 0.1mf 10% 25v c586 1-216-295-91 short 0 c600 ! 1-104-705-51 film 0.1mf 20% 250v c602 ! 1-104-705-51 film 0.1mf 20% 250v c604 1-163-009-11 ceramic chip 0.001mf 10% 50v c605 ! 1-127-942-51 ceramic 330pf 10% 250v c606 ! 1-127-942-51 ceramic 330pf 10% 250v c607 1-161-830-00 ceramic 0.0047mf 99% 500v c608 1-161-830-00 ceramic 0.0047mf 99% 500v c609 1-126-968-11 elect 100mf 20% 50v a www.datasheet.co.kr datasheet pdf - http://www..net/
75 ref. no. part no. description remark the components identified by shading and mark ! are critical for safety. replace only with part number specified. ref. no. part no. description remark kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 c610 1-126-964-11 elect 10mf 20% 50v c610 8-719-210-21 diode 11eqs04 c611 1-161-830-00 ceramic 0.0047mf 99% 500v c612 1-161-830-00 ceramic 0.0047mf 99% 500v c613 1-117-752-11 elect(block) 330mf 20% 450v c614 1-126-964-11 elect 10mf 20% 50v c616 1-130-202-00 film 0.022mf 10% 400v c617 1-107-792-11 ceramic 100pf 5% 1kv c618 1-125-893-11 film 680pf 3% 1.5kv c619 ! 1-119-886-51 ceramic 470pf 10% 250v c620 1-163-133-00 ceramic chip 470pf 5% 50v c621 1-102-114-00 ceramic 470pf 10% 50v c622 1-102-119-00 ceramic 0.0015mf 10% 50v (except kv-pf21m40/pfm70(e)/pf21p41) c623 1-104-665-11 elect 100mf 20% 25v c624 1-125-772-91 ceramic 1500pf 10% 2kv (except kv-pf21m40/pf21m70(e)/pf21p41) c627 1-102-002-00 ceramic 680pf 10% 500v c628 1-126-942-61 elect 1000mf 20% 25v c629 1-126-964-11 elect 10mf 20% 50v c630 1-123-024-21 elect 33mf 160v c633 1-104-999-11 mylar 0.1mf 10% 200v c634 1-126-933-11 elect 100mf 20% 16v c635 1-104-665-11 elect 100mf 20% 10v c636 1-104-760-11 ceramic chip 0.047mf 10% 50v c639 1-164-004-11 ceramic chip 0.1mf 10% 25v c640 1-164-004-11 ceramic chip 0.1mf 10% 25v c641 1-102-002-00 ceramic 680pf 10% 500v c642 1-126-943-11 elect 2200mf 20% 25v c643 1-104-665-11 elect 100mf 20% 10v c644 1-104-331-11 ceramic 0.0022mf 10% 1kv c645 1-137-605-11 film 0.01mf 10% 250v c646 1-107-679-91 elect 10mf 20% 450v c647 1-163-275-11 ceramic chip 0.001mf 5% 50v c649 1-126-940-11 elect 330mf 20% 25v c650 1-163-275-11 ceramic chip 0.001mf 5% 50v c651 1-163-133-00 ceramic chip 470pf 5% 50v c652 1-126-965-11 elect 22mf 20% 50v c653 1-104-664-11 elect 47mf 20% 25v c657 1-101-821-00 ceramic 0.0022mf 500v c658 1-164-004-11 ceramic chip 0.1mf 10% 25v c901 1-136-153-00 film 0.01mf 5% 50v c905 1-126-963-11 elect 4.7mf 20% 50v c906 1-164-346-11 ceramic chip 1mf 16v c907 1-163-133-00 ceramic chip 470pf 5% 50v c910 1-126-967-11 elect 47mf 20% 50v c911 1-126-967-11 elect 47mf 20% 50v c912 1-164-004-11 ceramic chip 0.1mf 10% 25v c913 1-104-665-11 elect 100mf 20% 10v c914 1-163-133-00 ceramic chip 470pf 5% 50v < cn104 1-695-915-11 tab (contact) cn202 * 1-785-608-11 pin, connector 4p cn203 * 1-564-506-11 plug, connector 3p cn204 * 1-564-506-11 plug, connector 3p cn301 * 1-774-813-11 connector, board to board 7p (kv-pf21p41 only) cn305 * 1-564-509-11 plug, connector 6p cn307 * 1-774-813-11 connector, board to board 7p (kv-pf21p41 only) cn505 1-508-765-00 pin, connector (5mm pitch) 3p cn506 4-352-844-01 pin, lead, coating cn601 * 1-580-843-11 pin, connector (power) cn602 * 1-508-786-00 pin, connector (5mm pitch) 2p cn604 * 1-573-963-11 pin, connector (pc board) 3p cn609 * 1-508-784-21 pin, connector (5mm pitch) 1p cn901 * 1-564-506-11 plug, connector 3p < d001 8-719-988-61 diode 1ss355te-17 d005 8-719-988-61 diode 1ss355te-17 d006 8-719-988-61 diode 1ss355te-17 d203 8-719-914-42 diode da204k d300 1-216-295-91 short 0 d301 8-719-988-61 diode 1ss355te-17 d306 8-719-988-61 diode 1ss355te-17 d307 8-719-988-61 diode 1ss355te-17 d308 8-719-988-61 diode 1ss355te-17 d309 8-719-069-54 diode udzs-te17-5.1b d311 8-719-988-61 diode 1ss355te-17 d312 8-719-988-61 diode 1ss355te-17 d313 8-719-988-61 diode 1ss355te-17 d314 8-719-988-61 diode 1ss355te-17 d315 8-719-988-61 diode 1ss355te-17 d316 8-719-069-57 diode udzs-te17-6.8b d320 8-719-069-60 diode udzs-te17-9.1b d321 8-719-069-60 diode udzs-te17-9.1b d402 8-719-069-60 diode udzs-te17-9.1b d403 8-719-069-60 diode udzs-te17-9.1b d405 8-719-069-60 diode udzs-te17-9.1b d406 8-719-069-60 diode udzs-te17-9.1b d504 8-719-302-43 diode el1z d505 8-719-988-61 diode 1ss355te-17 d506 8-719-911-19 diode 1ss119-25 d507 8-719-988-61 diode 1ss355te-17 d508 8-719-988-61 diode 1ss355te-17 d509 1-216-073-00 res,chip 10k 5% 1/10w d510 8-719-988-61 diode 1ss355te-17 d511 8-719-988-61 diode 1ss355te-17 d512 8-719-988-61 diode 1ss355te-17 d513 8-719-908-03 diode gp08d d517 8-719-312-71 diode rs3fs d518 8-719-900-26 diode erd29-08j d521 8-719-302-43 diode el1z d522 8-719-302-43 diode el1z d523 8-719-302-43 diode el1z d527 8-719-908-03 diode gp08d d528 8-719-908-03 diode gp08d d531 8-719-988-61 diode 1ss355te-17 d532 8-719-988-61 diode 1ss355te-17 d534 1-216-295-91 short 0 d602 8-719-911-19 diode 1ss119-25 d603 8-719-150-92 diode rd33eb3t d604 8-719-028-72 diode rgp02-17el-6433 a www.datasheet.co.kr datasheet pdf - http://www..net/
76 ref. no. part no. description remark ref. no. part no. description remark the components identified by shading and mark ! are critical for safety. replace only with part number specified. kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 d605 8-719-510-53 diode d4sb60l d606 8-719-108-18 thyristor 5p6m d607 8-719-073-01 diode ma111-(k8).s0 d608 8-719-110-53 diode rd20esb2 d609 8-719-311-31 diode ru-1p d611 8-719-046-74 diode au-01z-v1 d613 8-719-046-74 diode au-01z-v1 d614 8-719-046-74 diode au-01z-v1 d618 8-719-067-18 diode rn4z d620 8-719-110-72 diode rd30esb2 d622 8-719-071-39 diode fmu-g26s d623 8-719-978-65 diode dtz-tt11-15b d624 8-719-073-01 diode ma111-(k8).s0 d625 8-719-977-28 diode dtz10b d627 8-719-073-84 diode 31dq06-fc5 d628 8-719-911-19 diode 1ss119-25 d631 8-719-068-00 diode erc04-06se d632 8-719-068-00 diode erc04-06se d633 8-719-030-25 diode eg01cv0 d634 8-719-073-01 diode ma111-(k8).s0 d635 8-719-073-01 diode ma111-(k8).s0 d636 8-719-510-02 diode d1ns4 d637 8-719-109-96 diode rd6.8esb1 d638 8-719-024-99 diode 11es2-nta2b d901 8-719-069-60 diode udzs-te17-9.1b d902 8-719-069-60 diode udzs-te17-9.1b d904 8-719-069-60 diode udzs-te17-9.1b d905 8-719-069-60 diode udzs-te17-9.1b d906 8-719-045-19 diode spb-26mvwf < dy1 * 1-580-798-11 connector pin (dy) 6p < fb501 1-410-397-21 ferrite 1.1uh fb502 1-410-397-21 ferrite 1.1uh fb600 1-410-397-21 ferrite 1.1uh fb601 1-410-397-21 ferrite 1.1uh fb602 1-410-397-21 ferrite 1.1uh fb603 1-410-397-21 ferrite 1.1uh fb604 1-410-397-21 ferrite 1.1uh fb607 1-410-397-21 ferrite 1.1uh fb608 1-410-397-21 ferrite 1.1uh fb611 1-410-397-21 ferrite 1.1uh fb613 1-410-397-21 ferrite 1.1uh fb615 1-410-397-21 ferrite 1.1uh < ic001 8-752-906-20 ic cxp86449-622s (kv-pf21l70/pf21q70)/ m70(me) ic001 8-752-906-21 ic cxp86449-623s (except kv-pf21l70/pf21q70/ m70(me) ic002 8-759-371-21 ic mm1319afbe ic003 8-759-527-71 ic m24c08-bn6 ic201 8-759-339-60 ic ta8248k ic203 8-759-553-40 ic tda7429s ic301 8-752-088-39 ic cxa2130s ic502 8-759-700-07 ic njm2903m ic503 8-759-980-58 ic tda8172 ic601 8-749-013-75 ic str-f6654 ic602 8-749-920-61 ic se-135n ic603 8-759-701-59 ic njm78m09fa ic604 8-759-231-53 ic ta7805s ic901 8-742-014-11 hyb ic sbx1981-51 < j401 1-779-849-11 jack block, pin 4p j901 1-770-785-11 jack j902 1-779-205-11 jack, pin 2p < jr001 1-216-295-91 short 0 jr002 1-216-295-91 short 0 jr003 1-216-295-91 short 0 jr004 1-216-295-91 short 0 jr005 1-216-295-91 short 0 jr006 1-216-295-91 short 0 jr007 1-216-295-91 short 0 jr008 1-216-295-91 short 0 jr009 1-216-295-91 short 0 jr010 1-216-295-91 short 0 jr011 1-216-295-91 short 0 jr012 1-216-295-91 short 0 jr013 1-216-295-91 short 0 jr014 1-216-295-91 short 0 jr015 1-216-295-91 short 0 jr016 1-216-295-91 short 0 jr018 1-216-295-91 short 0 jr019 1-216-295-91 short 0 jr102 1-216-295-91 short 0 jr109 1-216-295-91 short 0 jr202 1-216-295-91 short 0 jr301 1-216-295-91 short 0 jr303 1-216-295-91 short 0 jr404 1-216-295-91 short 0 jr405 1-216-295-91 short 0 jr500 1-216-295-91 short 0 jr501 1-216-295-91 short 0 jr503 1-216-295-91 short 0 jr600 1-216-295-91 short 0 < l002 1-414-856-11 inductor 10uh l003 1-414-180-11 inductor 3.3uh l005 1-414-233-22 inductor chip 0uh l101 1-414-856-11 inductor 10uh l102 1-414-856-11 inductor 10uh l103 1-414-856-11 inductor 10uh l104 1-414-856-11 inductor 10uh l105 1-414-856-11 inductor 10uh a www.datasheet.co.kr datasheet pdf - http://www..net/
77 ref. no. part no. description remark the components identified by shading and mark ! are critical for safety. replace only with part number specified. ref. no. part no. description remark kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 l204 1-414-856-11 inductor 10uh l301 1-414-189-31 inductor 100uh l302 1-414-185-41 inductor 22uh l501 1-412-525-31 inductor 10uh l502 1-422-613-11 coil, air core l503 1-412-525-31 inductor 10uh l504 1-412-525-31 inductor 10uh l505 1-412-525-31 inductor 10uh l506 1-412-525-31 inductor 10uh l507 1-459-111-00 inductor 10mmh l508 1-412-525-31 inductor 10uh l509 1-459-390-00 inductor 390uh l510 1-416-972-11 coil, horizontal linearity l512 1-412-549-31 inductor 1mmh l513 1-412-549-31 inductor 1mmh l515 1-459-104-00 coil, with core l518 1-414-187-11 inductor 47uh l601 1-412-527-11 inductor 15uh l901 1-408-603-31 inductor 10uh l905 1-414-856-11 inductor 10uh < ph600 ! 8-749-010-64 photo coupler pc123f2 < ps200 1-532-675-21 link, ic 1.5a/150v < q002 8-729-230-49 transistor 2sc2712-yg q003 8-729-424-08 transistor un2111 q004 8-729-421-22 transistor un2211 q101 8-729-230-49 transistor 2sc2712-yg q201 8-729-424-67 transistor un2216 q203 8-729-421-19 transistor un2213 q204 8-729-216-22 transistor 2sa1162-g q206 8-729-421-19 transistor un2213 q207 8-729-421-19 transistor un2213 q301 8-729-216-22 transistor 2sa1162-g q302 8-729-230-49 transistor 2sc2712-yg q303 8-729-216-22 transistor 2sa1162-g q305 8-729-216-22 transistor 2sa1162-g q306 8-729-216-22 transistor 2sa1162-g q307 8-729-230-49 transistor 2sc2712-yg q308 8-729-216-22 transistor 2sa1162-g q312 8-729-216-22 transistor 2sa1162-g q313 8-729-230-49 transistor 2sc2712-yg q315 8-729-421-19 transistor un2213 q401 8-729-424-67 transistor un2216 q404 8-729-216-22 transistor 2sa1162-g q503 8-729-230-49 transistor 2sc2712-yg q505 8-729-931-45 transistor irf614 q506 8-729-140-96 transistor 2sd774-34 q507 8-729-216-22 transistor 2sa1162-g q509 8-729-230-49 transistor 2sc2712-yg q511 8-729-048-07 transistor 2sd2578-ca q601 8-729-023-22 transistor 2sd2114k q602 8-729-230-49 transistor 2sc2712-yg q603 8-729-424-08 transistor un2111 q604 8-729-200-17 transistor 2sa1091-o q605 8-729-044-30 transistor 2sk2845-lb102 q606 8-729-230-49 transistor 2sc2712-yg q606 8-729-120-28 transistor 2sc1623-l5l6 q607 8-729-922-37 transistor 2sd2144s-uvw q608 8-729-230-49 transistor 2sc2712-yg q901 8-729-421-19 transistor un2213 q902 8-729-421-19 transistor un2213 < r001 1-414-233-22 inductor chip 0uh r002 1-216-025-91 res,chip 100 5% 1/10w r003 1-216-295-91 short 0 r004 1-216-025-91 res,chip 100 5% 1/10w r005 1-216-025-91 res,chip 100 5% 1/10w r007 1-216-295-91 short 0 r008 1-216-065-91 res,chip 4.7k 5% 1/10w r010 1-216-065-91 res,chip 4.7k 5% 1/10w r011 1-216-065-91 res,chip 4.7k 5% 1/10w r012 1-216-065-91 res,chip 4.7k 5% 1/10w r013 1-216-065-91 res,chip 4.7k 5% 1/10w r014 1-216-025-91 res,chip 100 5% 1/10w r015 1-216-025-91 res,chip 100 5% 1/10w r017 1-216-049-91 res,chip 1k 5% 1/10w r018 1-216-033-00 res,chip 220 5% 1/10w r019 1-216-073-00 res,chip 10k 5% 1/10w r021 1-216-073-00 res,chip 10k 5% 1/10w r022 1-216-033-00 res,chip 220 5% 1/10w r024 1-216-057-00 res,chip 2.2k 5% 1/10w r025 1-216-057-00 res,chip 2.2k 5% 1/10w r026 1-216-057-00 res,chip 2.2k 5% 1/10w r027 1-216-073-00 res,chip 10k 5% 1/10w r029 1-216-049-91 res,chip 1k 5% 1/10w r031 1-216-049-91 res,chip 1k 5% 1/10w r035 1-216-025-91 res,chip 100 5% 1/10w r036 1-216-025-91 res,chip 100 5% 1/10w r037 1-216-025-91 res,chip 100 5% 1/10w r040 1-216-025-91 res,chip 100 5% 1/10w r041 1-216-025-91 res,chip 100 5% 1/10w r042 1-216-295-91 short 0 r043 1-216-049-91 res,chip 1k 5% 1/10w r044 1-216-025-91 res,chip 100 5% 1/10w r045 1-414-233-22 inductor chip 0uh r046 1-216-049-91 res,chip 1k 5% 1/10w r047 1-414-233-22 inductor chip 0uh r048 1-216-073-00 res,chip 10k 5% 1/10w r050 1-216-073-00 res,chip 10k 5% 1/10w r053 1-216-049-91 res,chip 1k 5% 1/10w r055 1-216-073-00 res,chip 10k 5% 1/10w r056 1-216-073-00 res,chip 10k 5% 1/10w a www.datasheet.co.kr datasheet pdf - http://www..net/
78 ref. no. part no. description remark ref. no. part no. description remark the components identified by shading and mark ! are critical for safety. replace only with part number specified. kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 r331 1-216-295-91 short 0 r332 1-216-033-00 res,chip 220 5% 1/10w r333 1-216-073-00 res,chip 10k 5% 1/10w r334 1-216-129-00 res,chip 2.2m 5% 1/10w r335 1-216-045-00 res,chip 680 5% 1/10w r338 1-216-033-00 res,chip 220 5% 1/10w r340 1-216-025-91 res,chip 100 5% 1/10w r345 1-216-081-00 res,chip 22k 5% 1/10w r348 1-208-806-11 res,chip 10k 0.50% 1/10w r349 1-216-073-00 res,chip 10k 5% 1/10w r350 1-216-061-00 res,chip 3.3k 5% 1/10w r351 1-216-053-00 res,chip 1.5k 5% 1/10w r354 1-216-057-00 res,chip 2.2k 5% 1/10w r355 1-216-057-00 res,chip 2.2k 5% 1/10w r356 1-216-057-00 res,chip 2.2k 5% 1/10w r357 1-216-079-00 res,chip 18k 5% 1/10w r358 1-216-049-91 res,chip 1k 5% 1/10w r359 1-216-033-00 res,chip 220 5% 1/10w r360 1-216-033-00 res,chip 220 5% 1/10w r361 1-216-073-00 res,chip 10k 5% 1/10w r362 1-216-075-00 res,chip 12k 5% 1/10w r363 1-216-079-00 res,chip 18k 5% 1/10w r364 1-216-295-91 short 0 r365 1-216-033-00 res,chip 220 5% 1/10w r366 1-216-073-00 res,chip 10k 5% 1/10w r367 1-216-073-00 res,chip 10k 5% 1/10w r370 1-216-033-00 res,chip 220 5% 1/10w r375 1-216-025-91 res,chip 100 5% 1/10w (kv-pf21p41 only) r376 1-216-081-00 res,chip 22k 5% 1/10w r377 1-216-121-91 res,chip 1m 5% 1/10w r378 1-216-031-00 res,chip 180 5% 1/10w r404 1-216-073-00 res,chip 10k 5% 1/10w r405 1-216-049-91 res,chip 1k 5% 1/10w r406 1-216-073-00 res,chip 10k 5% 1/10w r408 1-216-049-91 res,chip 1k 5% 1/10w r411 1-216-113-00 res,chip 470k 5% 1/10w r412 1-216-041-00 res,chip 470 5% 1/10w r413 1-216-021-00 res,chip 68 5% 1/10w r414 1-216-113-00 res,chip 470k 5% 1/10w r417 1-216-077-00 res,chip 15k 5% 1/10w r418 1-216-113-00 res,chip 470k 5% 1/10w r419 1-216-022-00 res,chip 75 5% 1/10w r426 1-216-033-00 res,chip 220 5% 1/10w r505 1-216-099-00 res,chip 120k 5% 1/10w r506 1-216-085-00 res,chip 33k 5% 1/10w r507 1-249-389-11 carbon 4.7 5% 1/4w f r508 1-215-910-00 metal oxide 68 5% 3w f r509 1-215-911-11 metal oxide 100 5% 3w f r510 1-215-885-00 metal oxide 68 5% 2w f r511 1-215-911-11 metal oxide 100 5% 3w f r516 1-216-081-00 res,chip 22k 5% 1/10w r518 1-247-807-31 carbon 100 5% 1/4w r520 1-215-445-00 metal 10k 1% 1/4w r522 1-208-806-11 res,chip 10k 0.50% 1/10w r523 1-249-411-11 carbon 330 5% 1/4w r525 1-208-830-11 res,chip 100k 0.50% 1/10w r061 1-216-033-00 res,chip 220 5% 1/10w r062 1-216-041-00 res,chip 470 5% 1/10w r063 1-216-037-00 res,chip 330 5% 1/10w r064 1-216-037-00 res,chip 330 5% 1/10w r065 1-216-037-00 res,chip 330 5% 1/10w r066 1-216-049-91 res,chip 1k 5% 1/10w r067 1-216-049-91 res,chip 1k 5% 1/10w r105 1-216-295-91 short 0 r109 1-216-041-00 res,chip 470 5% 1/10w r111 1-216-025-91 res,chip 100 5% 1/10w r112 1-216-025-91 res,chip 100 5% 1/10w r113 1-216-047-91 res,chip 820 5% 1/10w r202 1-216-071-00 res,chip 8.2k 5% 1/10w r203 1-216-077-00 res,chip 15k 5% 1/10w r204 1-216-071-00 res,chip 8.2k 5% 1/10w r208 1-216-073-00 res,chip 10k 5% 1/10w r210 1-164-004-11 ceramic chip 0.1mf 10% 25v r211 1-216-043-91 res,chip 560 5% 1/10w r212 1-216-033-00 res,chip 220 5% 1/10w r213 1-216-073-00 res,chip 10k 5% 1/10w r214 1-216-073-00 res,chip 10k 5% 1/10w r215 1-216-059-00 res,chip 2.7k 5% 1/10w r216 1-216-059-00 res,chip 2.7k 5% 1/10w r217 1-216-067-00 res,chip 5.6k 5% 1/10w r218 1-216-067-00 res,chip 5.6k 5% 1/10w r219 1-216-025-91 res,chip 100 5% 1/10w r220 1-216-025-91 res,chip 100 5% 1/10w r221 1-216-295-91 short 0 r225 1-216-033-00 res,chip 220 5% 1/10w r226 1-216-033-00 res,chip 220 5% 1/10w r227 1-216-033-00 res,chip 220 5% 1/10w r229 1-216-073-00 res,chip 10k 5% 1/10w r231 1-216-295-91 short 0 r234 1-249-389-11 carbon 4.7 5% 1/4w r235 1-216-069-00 res,chip 6.8k 5% 1/10w r236 1-216-069-00 res,chip 6.8k 5% 1/10w r237 1-216-308-00 res,chip 4.7 5% 1/10w r301 1-216-073-00 res,chip 10k 5% 1/10w r302 1-216-295-91 short 0 r303 1-216-049-91 res,chip 1k 5% 1/10w r304 1-216-073-00 res,chip 10k 5% 1/10w r305 1-216-051-00 res,chip 1.2k 5% 1/10w r306 1-216-073-00 res,chip 10k 5% 1/10w r308 1-216-025-91 res,chip 100 5% 1/10w r309 1-216-025-91 res,chip 100 5% 1/10w r310 1-216-025-91 res,chip 100 5% 1/10w r311 1-216-017-91 res,chip 47 5% 1/10w r312 1-216-041-00 res,chip 470 5% 1/10w r313 1-216-053-00 res,chip 1.5k 5% 1/10w r314 1-216-045-00 res,chip 680 5% 1/10w r316 1-216-053-00 res,chip 1.5k 5% 1/10w r317 1-216-077-00 res,chip 15k 5% 1/10w r318 1-216-051-00 res,chip 1.2k 5% 1/10w r319 1-216-025-91 res,chip 100 5% 1/10w r320 1-216-065-91 res,chip 4.7k 5% 1/10w r321 1-216-073-00 res,chip 10k 5% 1/10w r322 1-216-033-00 res,chip 220 5% 1/10w a www.datasheet.co.kr datasheet pdf - http://www..net/
79 ref. no. part no. description remark the components identified by shading and mark ! are critical for safety. replace only with part number specified. ref. no. part no. description remark kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 r526 1-208-798-11 res,chip 4.7k 0.50% 1/10w r527 1-216-001-00 res,chip 10 5% 1/10w r528 1-208-814-91 res,chip 22k 0.50% 1/10w r529 1-208-766-11 res,chip 220 0.50% 1/10w r531 1-247-843-11 carbon 3.3k 5% 1/4w r533 1-249-417-11 carbon 1k 5% 1/4w r534 1-216-361-00 metal oxide 0.22 5% 2w f r535 1-216-067-00 res,chip 5.6k 5% 1/10w r536 1-216-067-00 res,chip 5.6k 5% 1/10w r537 1-208-814-91 res,chip 22k 0.50% 1/10w r540 1-216-065-91 res,chip 4.7k 5% 1/10w r541 1-216-065-91 res,chip 4.7k 5% 1/10w r542 1-216-295-91 short 0 r543 1-249-426-11 carbon 5.6k 5% 1/4w f r545 1-216-077-00 res,chip 15k 5% 1/10w r546 1-216-077-00 res,chip 15k 5% 1/10w r547 1-216-085-00 res,chip 33k 5% 1/10w r549 1-215-451-00 metal 18k 1% 1/4w r550 1-216-097-91 res,chip 100k 5% 1/10w r551 1-249-421-11 carbon 2.2k 5% 1/4w r552 1-216-057-00 res,chip 2.2k 5% 1/10w r553 1-215-457-00 metal 33k 1% 1/4w r554 1-215-457-00 metal 33k 1% 1/4w r556 1-215-437-00 metal 4.7k 1% 1/4w r558 1-249-421-11 carbon 2.2k 5% 1/4w r559 1-249-429-11 carbon 10k 5% 1/4w r560 1-216-073-00 res,chip 10k 5% 1/10w r562 1-249-401-11 carbon 47 5% 1/4w r565 1-216-073-00 res,chip 10k 5% 1/10w r567 1-216-105-91 res,chip 220k 5% 1/10w r568 1-249-383-11 carbon 1.5 5% 1/4w f r570 1-216-069-00 res,chip 6.8k 5% 1/10w r571 1-215-437-00 metal 4.7k 1% 1/4w r573 1-216-089-91 res,chip 47k 5% 1/10w r577 1-215-913-11 metal oxide 220 5% 3w f r578 1-216-369-00 metal oxide 1 5% 2w f r579 1-216-097-91 res,chip 100k 5% 1/10w r580 1-208-830-11 res,chip 100k 0.50% 1/10w r581 1-208-798-11 res,chip 4.7k 0.50% 1/10w r585 1-249-391-11 carbon 6.8 5% 1/4w f r588 1-215-888-00 metal oxide 220 5% 2w f r589 1-215-888-00 metal oxide 220 5% 2w f r590 1-215-465-00 metal 68k 1% 1/4w r591 1-260-288-11 carbon 0.47 5% 1/2w f r593 1-260-288-11 carbon 0.47 5% 1/2w f r594 1-260-288-11 carbon 0.47 5% 1/2w f r596 1-215-922-11 metal oxide 6.8k 5% 3w f r597 1-247-750-11 carbon 680 5% 1/2w f r598 1-249-438-11 carbon 56k 5% 1/4w r599 1-249-389-11 carbon 4.7 5% 1/4w r600 1-249-438-11 carbon 56k 5% 1/4w r601 1-249-418-11 carbon 1.2k 5% 1/4w f r602 1-249-389-11 carbon 4.7 5% 1/4w f r603 1-215-485-00 metal 470k 1% 1/4w r604 1-216-097-91 res,chip 100k 5% 1/10w r607 1-249-425-11 carbon 4.7k 5% 1/4w r608 1-240-205-91 carbon 22m 5% 1/2w r609 1-216-057-00 res,chip 2.2k 5% 1/10w r610 1-216-073-00 res,chip 10k 5% 1/10w r611 1-216-089-91 res,chip 47k 5% 1/10w r612 1-216-045-00 res,chip 680 5% 1/10w r614 1-216-041-00 res,chip 470 5% 1/10w r615 1-216-350-11 metal oxide 1.2 5% 1w f r616 1-260-302-51 carbon 6.8 5% 1/2w f r617 1-247-791-91 carbon 22 5% 1/4w r619 1-260-128-11 carbon 270k 5% 1/2w r620 1-215-915-11 metal oxide 470 5% 3w f r622 1-215-908-00 metal oxide 33 5% 3w f r623 1-216-095-00 res,chip 82k 5% 1/10w r624 1-216-089-91 res,chip 47k 5% 1/10w r626 1-216-049-91 res,chip 1k 5% 1/10w r627 1-240-251-11 cmt,melf 6.8 5% 10w r629 1-247-747-11 carbon 470 5% 1/2w f r630 1-249-429-11 carbon 10k 5% 1/4w f r631 1-216-089-91 res,chip 47k 5% 1/10w r632 1-202-933-61 fusible 0.1 10% 1/2w f r634 ! 1-218-265-11 metal 8.2m 5% 1w r635 1-216-492-11 metal oxide 82k 5% 3w f r636 1-215-924-00 metal oxide 15k 5% 3w f r637 1-216-492-11 metal oxide 82k 5% 3w f r639 1-216-363-00 metal oxide 0.33 5% 2w f r640 1-249-415-11 carbon 680 5% 1/4w r641 1-216-362-11 metal oxide 0.27 5% 2w f r642 1-249-419-11 carbon 1.5k 5% 1/4w r643 1-247-843-11 carbon 3.3k 5% 1/4w r644 1-249-419-11 carbon 1.5k 5% 1/4w r646 1-215-924-00 metal oxide 15k 5% 3w f r647 1-249-401-11 carbon 47 5% 1/4w r648 1-216-057-00 res,chip 2.2k 5% 1/10w r649 1-249-417-11 carbon 1k 5% 1/4w r650 1-215-882-00 metal oxide 22 5% 2w f r652 1-215-900-11 metal oxide 22k 5% 2w f r653 1-215-873-00 metal oxide 4.7k 5% 1w f r657 1-260-127-11 carbon 220k 5% 1/2w r659 1-216-049-91 res,chip 1k 5% 1/10w r660 1-216-073-00 res,chip 10k 5% 1/10w r661 1-215-873-00 metal oxide 4.7k 5% 1w f r901 1-249-411-11 carbon 330 5% 1/4w r903 1-216-022-00 res,chip 75 5% 1/10w r904 1-216-033-00 res,chip 220 5% 1/10w r905 1-216-113-00 res,chip 470k 5% 1/10w r906 1-216-077-00 res,chip 15k 5% 1/10w r909 1-216-065-91 res,chip 4.7k 5% 1/10w r910 1-216-065-91 res,chip 4.7k 5% 1/10w r911 1-216-067-00 res,chip 5.6k 5% 1/10w r912 1-216-041-00 res,chip 470 5% 1/10w r913 1-216-049-91 res,chip 1k 5% 1/10w r914 1-216-055-00 res,chip 1.8k 5% 1/10w r915 1-216-061-00 res,chip 3.3k 5% 1/10w r916 1-216-017-91 res,chip 47 5% 1/10w r917 1-216-041-00 res,chip 470 5% 1/10w r918 1-216-041-00 res,chip 470 5% 1/10w a www.datasheet.co.kr datasheet pdf - http://www..net/
80 ref. no. part no. description remark ref. no. part no. description remark the components identified by shading and mark ! are critical for safety. replace only with part number specified. kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 < ry601 ! 1-755-266-11 relay, ac power < s502 1-572-707-11 switch, lever s600 ! 1-571-433-21 switch, push (ac power) s901 1-692-431-21 switch, tactile s902 1-692-431-21 switch, tactile s903 1-692-431-21 switch, tactile s904 1-692-431-21 switch, tactile s905 1-692-431-21 switch, tactile s906 1-692-431-21 switch, tactile s907 1-692-431-21 switch, tactile < t501 1-437-195-11 transformer, horizontal drive t503 ! 1-453-293-11 transformer assy, flyback (nx-1748//m3a4) (except kv-pf21m70(me)) t503 ! 1-453-298-11 transformer assy, flyback (nx-1748//m3a4) (kv-pf21m70(me)) t601 1-424-682-11 transformer, line filter t603 ! 1-433-512-31 transformer, converter (srt) t604 ! 1-431-852-11 transformer, converter (srt) < thp600 1-810-961-11 thermistor, positive < tu101 8-598-447-00 tuner, fss btf-lg411 (except kv-pf21m40/ pf21m70) tu101 8-598-449-10 tuner, fss btf-lg433 (kv-pf21m40/pf21m70) < x001 1-579-125-11 vibrator, ceramic x301 1-781-134-21 vibrator, crystal x302 1-781-132-21 vibrator, crystal (except kv-pf21q70) *************************************************************************** * a-1331-884-a c3 board, mounted ********************* 7-682-948-01 screw +psw 3x8 < c701 1-162-114-00 ceramic 0.0047mf 2kv c702 1-102-074-00 ceramic 0.001mf 10% 50v c703 1-107-651-11 elect 4.7mf 20% 250v c704 1-130-202-00 film 0.022mf 5% 400v c706 1-104-664-11 elect 47mf 20% 16v c708 1-102-114-00 ceramic 470pf 10% 50v c709 1-102-114-00 ceramic 470pf 10% 50v c710 1-102-114-00 ceramic 470pf 10% 50v c712 1-102-116-00 ceramic 680pf 10% 50v c713 1-102-116-00 ceramic 680pf 10% 50v c714 1-102-116-00 ceramic 680pf 10% 50v c716 1-126-933-11 elect 100mf 20% 16v c717 1-101-880-00 ceramic 47pf 5% 50v c736 1-102-114-00 ceramic 470pf 10% 50v c737 1-102-114-00 ceramic 470pf 10% 50v c746 1-102-114-00 ceramic 470pf 10% 50v < cn701 1-508-765-00 pin, connector (5mm pitch) 3p cn702 1-695-915-11 tab (contact) cn703 * 1-564-509-11 plug, connector 6p cn704 1-695-915-11 tab (contact) < d701 8-719-911-19 diode 1ss119-25 d702 8-719-911-19 diode 1ss119-25 d703 8-719-911-19 diode 1ss119-25 d707 8-719-911-19 diode 1ss119-25 d708 8-719-911-19 diode 1ss119-25 d709 8-719-911-19 diode 1ss119-25 d710 8-719-911-19 diode 1ss119-25 d711 8-719-911-19 diode 1ss119-25 d712 8-719-911-19 diode 1ss119-25 d713 8-719-911-19 diode 1ss119-25 d714 8-719-911-19 diode 1ss119-25 d715 8-719-911-19 diode 1ss119-25 d716 8-719-911-19 diode 1ss119-25 d717 8-719-121-26 diode rd9.1esl2 < j701 ! 1-540-071-22 socket, crt < l701 1-410-667-31 inductor 22uh l710 1-408-613-31 inductor 68uh l711 1-408-613-31 inductor 68uh l712 1-408-613-31 inductor 68uh < q704 8-729-326-11 transistor 2sc2611 q705 8-729-326-11 transistor 2sc2611 q706 8-729-326-11 transistor 2sc2611 q707 8-729-200-17 transistor 2sa1091-o q708 8-729-200-17 transistor 2sa1091-o q709 8-729-200-17 transistor 2sa1091-o q710 8-729-119-78 transistor 2sc2785-hfe q711 8-729-119-78 transistor 2sc2785-hfe q712 8-729-119-78 transistor 2sc2785-hfe a c 3 www.datasheet.co.kr datasheet pdf - http://www..net/
81 ref. no. part no. description remark the components identified by shading and mark ! are critical for safety. replace only with part number specified. ref. no. part no. description remark kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 < r703 1-249-496-11 carbon 100k 5% 1/2w r705 1-216-380-11 metal oxide 8.2 5% 2w f r706 1-215-417-00 metal 680 1% 1/4w r707 1-215-413-00 metal 470 1% 1/4w r708 1-216-379-11 metal oxide 6.8 5% 2w f r710 1-215-922-11 metal oxide 6.8k 5% 3w f r711 1-247-752-11 carbon 1k 5% 1/2w r712 1-215-922-11 metal oxide 6.8k 5% 3w f r713 1-247-752-11 carbon 1k 5% 1/2w r714 1-215-922-11 metal oxide 6.8k 5% 3w f r715 1-247-752-11 carbon 1k 5% 1/2w r719 1-215-480-00 metal 300k 1% 1/4w r720 1-249-923-11 carbon 1k 5% 1/4w f r721 1-215-489-00 metal 680k 1% 1/4w r722 1-249-923-11 carbon 1k 5% 1/4w f r723 1-215-479-00 metal 270k 1% 1/4w r724 1-249-923-11 carbon 1k 5% 1/4w f r725 1-249-421-11 carbon 2.2k 5% 1/4w r726 1-249-421-11 carbon 2.2k 5% 1/4w r727 1-249-421-11 carbon 2.2k 5% 1/4w r728 1-249-407-11 carbon 150 5% 1/4w r729 1-249-407-11 carbon 150 5% 1/4w r730 1-249-407-11 carbon 150 5% 1/4w r731 1-249-407-11 carbon 150 5% 1/4w r732 1-249-407-11 carbon 150 5% 1/4w r733 1-249-406-11 carbon 120 5% 1/4w r734 1-247-739-11 carbon 100 5% 1/2w r738 1-247-807-31 carbon 100 5% 1/4w r739 1-247-807-31 carbon 100 5% 1/4w r740 1-247-807-31 carbon 100 5% 1/4w r755 1-249-418-11 carbon 1.2k 5% 1/4w r756 1-249-418-11 carbon 1.2k 5% 1/4w r757 1-249-418-11 carbon 1.2k 5% 1/4w < rv702 1-241-656-21 res, adj, metal film 110m *************************************************************************** * a-1241-355-a f board, mounted ******************* 1-533-223-11 clip, fuse * 4-374-846-01 cover, capacitor, cap type < c654 1-117-703-11 ceramic 0.0047mf 99% 250v c4602 ! 1-104-708-91 film 0.47mf 20% 250v < cn4601* 1-580-843-11 pin, connector (power) cn4602* 1-580-843-11 pin, connector (power) cn4603 1-695-915-11 tab (contact) < f4601 ! 1-532-237-11 fuse, time-lag (bet) 3.15a/250v < r4601 ! 1-202-719-11 solid 1m 10% 1/2w < t4601 1-424-682-91 transformer, line filter (except kv- pf21p10) t4602 1-424-682-91 transformer, line filter (except kv- pf21p10) t4601 ! 1-424-682-91 transformer, line filter (kv-pf21p10) t4602 ! 1-424-682-91 transformer, line filter (kv-pf21p10) < vdr461 1-801-073-31 varistor tnr14v471k660 *************************************************************************** * a-1347-155-a v1 board, complete (kv-pf21p41 only) ********************** < c801 1-104-664-11 elect 47mf 20% 16v c805 1-163-038-91 ceramic chip 0.1mf 25v c806 1-163-038-91 ceramic chip 0.1mf 25v c815 1-163-251-11 ceramic chip 100pf 5% 50v c816 1-164-505-11 ceramic chip 2.2mf 16v c817 1-164-004-11 ceramic chip 0.1mf 10% 25v c818 1-163-239-11 ceramic chip 33pf 5% 50v c820 1-163-239-11 ceramic chip 33pf 5% 50v c821 1-163-038-91 ceramic chip 0.1mf 25v c822 1-163-009-11 ceramic chip 0.001mf 10% 50v c823 1-126-933-11 elect 100mf 20% 16v c826 1-126-963-11 elect 4.7mf 20% 50v c829 1-163-113-00 ceramic chip 68pf 5% 50v c830 1-163-038-91 ceramic chip 0.1mf 25v c831 1-126-933-11 elect 100mf 20% 16v c832 1-126-964-11 elect 10mf 20% 50v c835 1-163-038-91 ceramic chip 0.1mf 25v c837 1-126-933-11 elect 100mf 20% 16v f c 3 v 1 www.datasheet.co.kr datasheet pdf - http://www..net/
82 ref. no. part no. description remark ref. no. part no. description remark the components identified by shading and mark ! are critical for safety. replace only with part number specified. kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 < cn801 * 1-774-812-11 connector, board to board 7p cn803 * 1-774-812-11 connector, board to board 7p < d802 8-719-914-44 diode dap202k d803 8-719-105-46 diode rd3.3m-b2 d804 8-719-105-91 diode rd5.6m-b2 d806 8-719-988-61 diode 1ss355te-17 d807 8-719-988-61 diode 1ss355te-17 < fb801 1-410-397-21 ferrite 1.1uh fb802 1-410-397-21 ferrite 1.1uh fb803 1-410-397-21 ferrite 1.1uh fb804 1-410-682-31 inductor 470uh fb805 1-410-397-21 ferrite 1.1uh < ic801 8-759-476-87 ic saa5261 < jr801 1-216-295-91 short 0 jr802 1-216-295-91 short 0 jr804 1-216-295-91 short 0 jr805 1-216-295-91 short 0 jr806 1-216-295-91 short 0 jr807 1-216-295-91 short 0 jr808 1-216-295-91 short 0 < q801 8-729-120-28 transistor 2sc1623-l5l6 q803 8-729-120-28 transistor 2sc1623-l5l6 q805 8-729-120-28 transistor 2sc1623-l5l6 q806 8-729-120-28 transistor 2sc1623-l5l6 q807 8-729-120-28 transistor 2sc1623-l5l6 q808 8-729-120-28 transistor 2sc1623-l5l6 q810 8-729-120-28 transistor 2sc1623-l5l6 q811 8-729-019-01 transistor 2sd2394-ef q812 8-729-120-28 transistor 2sc1623-l5l6 q813 8-729-120-28 transistor 2sc1623-l5l6 q814 8-729-120-28 transistor 2sc1623-l5l6 q817 8-729-900-53 transistor dtc114ek q818 8-729-120-28 transistor 2sc1623-l5l6 < r800 1-208-806-11 res,chip 10k 0.50% 1/10w r801 1-216-295-91 short 0 r802 1-216-025-91 res,chip 100 5% 1/10w r803 1-216-295-91 short 0 r804 1-216-295-91 short 0 r805 1-216-295-91 short 0 r807 1-216-295-91 short 0 r813 1-216-295-91 short 0 r820 1-216-073-00 res,chip 10k 5% 1/10w r821 1-216-083-00 res,chip 27k 5% 1/10w r822 1-216-025-91 res,chip 100 5% 1/10w r824 1-216-295-91 short 0 r825 1-216-295-91 short 0 r827 1-216-295-91 short 0 r828 1-216-025-91 res,chip 100 5% 1/10w r829 1-216-025-91 res,chip 100 5% 1/10w r830 1-216-295-91 short 0 r831 1-216-295-91 short 0 r832 1-208-790-11 res,chip 2.2k 0.50% 1/10w r835 1-216-295-91 short 0 r839 1-216-655-11 res,chip 1.5k 0.50% 1/10w r841 1-216-025-91 res,chip 100 5% 1/10w r842 1-216-065-91 res,chip 4.7k 5% 1/10w r843 1-216-065-91 res,chip 4.7k 5% 1/10w r844 1-216-057-00 res,chip 2.2k 5% 1/10w r845 1-216-049-91 res,chip 1k 5% 1/10w r846 1-216-049-91 res,chip 1k 5% 1/10w r847 1-216-049-91 res,chip 1k 5% 1/10w r848 1-216-049-91 res,chip 1k 5% 1/10w r849 1-216-049-91 res,chip 1k 5% 1/10w r850 1-216-105-91 res,chip 220k 5% 1/10w r851 1-216-057-00 res,chip 2.2k 5% 1/10w r853 1-216-067-00 res,chip 5.6k 5% 1/10w r857 1-216-081-00 res,chip 22k 5% 1/10w r858 1-216-067-00 res,chip 5.6k 5% 1/10w r861 1-216-049-91 res,chip 1k 5% 1/10w r862 1-260-095-11 carbon 470 5% 1/2w r863 1-216-049-91 res,chip 1k 5% 1/10w r864 1-216-041-00 res,chip 470 5% 1/10w r866 1-215-880-00 metal oxide 10 5% 2w f r871 1-216-037-00 res,chip 330 5% 1/10w r879 1-216-073-00 res,chip 10k 5% 1/10w r880 1-216-041-00 res,chip 470 5% 1/10w r882 1-216-049-91 res,chip 1k 5% 1/10w r884 1-216-025-91 res,chip 100 5% 1/10w r888 1-216-065-91 res,chip 4.7k 5% 1/10w r889 1-216-073-00 res,chip 10k 5% 1/10w r890 1-216-081-00 res,chip 22k 5% 1/10w r894 1-216-073-00 res,chip 10k 5% 1/10w r895 1-216-065-91 res,chip 4.7k 5% 1/10w r896 1-216-073-00 res,chip 10k 5% 1/10w r897 1-216-073-00 res,chip 10k 5% 1/10w r898 1-216-065-91 res,chip 4.7k 5% 1/10w < x801 1-578-774-11 vibrator, crystal *************************************************************************** v 1 www.datasheet.co.kr datasheet pdf - http://www..net/
83 ref. no. part no. description remark the components identified by shading and mark ! are critical for safety. replace only with part number specified. ref. no. part no. description remark kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 miscellaneous ***************** 1-416-946-21 coil, demagnetic 1-417-151-21 matching transformer, antenna (except kv-pf21p41) 1-452-032-00 magnet,disc 1-452-094-00 circular disc magnet b 1-501-372-81 antenna, telescopic (except kv-pf21l70/ pf21p41) 1-569-008-21 adaptor, conversion 2p (kv-pf21l70/ pf21m70(me)/pf21q70 only) 1-505-740-11 speaker (5x9cm) ! 1-574-062-11 cord, power (with connector) 2.5a/250v (exept kv-pf21p10) ! 1-574-358-11 cord, power (with connector) 7.5a/250v (kv-pf21p10) 8-451-505-11 deflection yoke (y21rsa-s) (exept kv- pf21p10) ! 8-451-505-11 deflection yoke (y21rsa-s)(kv-pf21p10) 8-738-812-05 picture tube (a51lpt70x) (kv-pf21m40/ pf21p40/pf21p41) 8-738-809-05 picture tube (a51lpt70x) (kv-pf21l70/ pf21m70/pf21p10/pf21q70) *************************************************************************** accessories and packing materials *************************************** 1-417-151-21 matching transformer, antenna (except kv-pf21p41) 1-501-372-81 antenna, telescopic (except kv-pf21l70/ pf21p41) 1-569-008-21 adaptor, conversion 2p (kv-pf21l70/ m70(me)/pf21q70 only) 3-701-910-00 screw, special (dia 3.8x20) 3-867-184-21 manu al,instruction (kv-pf21m40/pf21p40/ pf21p41) 3-867-184-31 manual,instruction (kv-pf21l70(me)/ pf21q70)/m70(me)) 3-867-184-61 manual,instruction (kv-pf21m70(e)) 3-867-184-41 manual,instruction (kv-pf21p10) * 4-070-297-01 cushion(upper)(assy) * 4-070-298-01 cushion(lower)(assy) 3-867-184-12 manual, instruction (kv-pf21m40/ge) * 4-070-299-01 individual carton 4-392-003-11 band, hold 4-392-004-11 clip * 4-392-859-01 bag, protection remote commander ********************** 1-418-163-11 remote commander (rm-952) 9-933-895-01 battery cover, remote commander www.datasheet.co.kr datasheet pdf - http://www..net/
84 ref. no. part no. description remark ref. no. part no. description remark the components identified by shading and mark ! are critical for safety. replace only with part number specified. kv-pf21l70/pf21m40/pf21m70/pf21p10 KV-PF21P40/pf21p41/pf21q70 rm-952 sony corporation sony tv industries (m) sdn. bhd. tv business of general area english 99gm70226-1 printed in malaysia ? 1999. 7 9-965-749-01 www.datasheet.co.kr datasheet pdf - http://www..net/

▲Up To Search▲

Price & Availability of KV-PF21P40

	To Download KV-PF21P40 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .