04/2011 aw t6625a awt6625a help4 tm umts800 (bands 5 & 6) wcdma, cdma multimode pam data sheet- rev 2.0 m45 package 10 pin 3 mm x 3 mm x 1 mm surface mount module figure 1: block diagram features ? multimode (hspa, evdo compliant) ? 4th generation help tm technology ? high effciency (r99): ? 40 % @ p out = +28.4 dbm ? 26 % @ p out = +17 dbm ? 17 % @ p out = +13.5 dbm ? 19 % @ p out = +8 dbm ? 11 % @ p out = +3.5 dbm ? low quiescent current: <3 ma ? low leakage current in shutdown mode: <5 a ? internal voltage regulator ? integrated daisy chainable directional coupler with cpl in and cpl out port. ? internal dc blocks on all rf ports ? optimized for a 50 ? system ? 1.8v control logic ? rohs compliant package, 260 o c msl-3 applications ? bands 5 & 6 ? band class 0 cdma/evdo wireless devices product description the awt6625a help4 tm pa is the 4th generation help tm product for wcdma devices operating in umts800 (bands 5 & 6) and for cdma devices operating in cell-band. this pa incorporates anadigics help4 tm technology to deliver exceptional effciency at low power levels and low quiescent current without the need for external voltage regulators or converters. the device is manufactured using advanced ingap- plus tm hbt technology offering state-of-the-art reliability, temperature stability, and ruggedness. three selectable bias modes that optimize effciency for different output power levels and a shutdown mode with low leakage current increase handset talk and standby time. a daisy chainable directional coupler is integrated in the module thus eliminating the need of an external coupler. the self-contained 3 mm x 3 mm x 1 mm surface mount package incorporates matching networks optimized for output power, effciency, and linearity in a 50 ? system. 1 2 3 4 5 10 9 8 7 6 v bat t rf in v mode 2 v mode 1 v en cp l ou t gn d cp l in rf ou t v cc bias contro l voltage regulatio n cp l gnd at slug (pad )
2 data sheet - rev 2.0 04/2011 awt6625a figure 2: pinout (x-ray top view) table 1: pin description v bat t rf in v mode 2 v mode 1 v en 1 2 3 4 5 6 7 8 9 10 cp l ou t gn d cp l in rf ou t v cc 1 2 3 4 5 6 7 8 9 10 pin name description 1 v batt battery voltage 2 rf in rf input 3 v mode2 mode control voltage 2 4 v mode1 mode control voltage 1 5 v en pa enable voltage 6 cpl out coupler output 7 gnd ground 8 cpl in coupler input 9 rf out rf output 10 v cc supply voltage
data sheet - rev 2.0 04/2011 awt6625a 3 electrical characteristics table 2: absolute minimum and maximum ratings stresses in excess of the absolute ratings may cause permanent damage. functional operation is not implied under these conditions. exposure to absolute ratings for extended periods of time may adversely affect reliability. table 3: operating ranges the device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defned in the electrical specifcations. parameter min max unit supply voltage (v cc ) 0 +5 v battery voltage (v batt ) 0 +6 v control voltages (v mode1 , v mode2 , v en ) 0 +3.5 v rf input power (p in ) - +10 dbm storage temperature (t stg ) -40 +150 c note: (1) for operation at 3.2 v, p out is derated by 0.5 db. parameter min typ max unit comments operating frequency (f) 824 - 849 mhz supply voltage (v cc ) +3.2 +3.4 +4.35 v p out ? +28.4 dbm enable voltage (v en ) +1.35 0 +1.8 - +3.1 +0.5 v pa "on" pa "shut down" mode control voltage (v mode1 , v mode2 ) +1.35 0 +1.8 - +3.1 +0.5 v low bias mode high bias mode umts (wcdma) ouput power r99, hpm hspa (mpr = 0), hpm r99, mpm hspa (mpr = 0), mpm r99, lpm hspa (mpr = 0), lpm 27.9 (1) 26.9 (1) - - - - 28.4 27.4 17.0 16.0 8.0 7.0 - - - - - - dbm 3gpp ts 34.121-1, rel 8 table c.11.1.3 for wcdma subtest 1 cdma output power hpm mpm lpm 27.2 (1) - - 27.7 16.0 7.0 - - - dbm cdma 2000, rc1 case temperature (tc) -30 - +90 ? c
4 data sheet - rev 2.0 04/2011 awt6625a table 4: electrical specifcations - wcdma operation (r99 modulation) (t c = +25 c, v cc = +3.4 v, v batt = +3.4 v, v en = +1.8 v, 50 ? system) notes: (1) aclr and effciency measured at 836.5 mhz. parameter min typ max unit comments p out v mode1 v mode2 gain 26 15 10 18 13 31 22 16 db p out = +28.4 dbm p out = +17 dbm p out = +8 dbm 0 v 1.8 v 1.8 v 0 v 0 v 1.8 v aclr1 at 5 mhz offset (1) - - - -41 -42 -40 -37.5 -37.5 -37.5 dbc p out = +28.4 dbm p out = +17 dbm p out = +8 dbm 0 v 1.8 v 1.8 v 0 v 0 v 1.8 v aclr2 at 10 mhz offset - - - -56 -57 -60 -48 -48 -48 dbc p out = +28.4 dbm p out = +17 dbm p out = +8 dbm 0 v 1.8 v 1.8 v 0 v 0 v 1.8 v power-added efficiency (1) 36 22 - 15 - 40 26 17 11 - - - - - p out = +28.4 dbm p out = +17 dbm p out = +13.5 dbm p out = +8 dbm p out = +3.5 dbm 0 v 1.8 v 1.8 v 1.8 v 1.8 v 0 v 0 v 0 v 1.8 v 1.8 v quiescent current (icq) low bias mode - 3 4.5 ma through v cc pin 1.8 v 1.8 v mode control current - 0.06 0.15 ma through v mode pins, v mode = 1.8 v enable current - 0.04 0.15 ma through v en pin batt current - 0.7 1.5 ma through v batt pin, v mode1 = +1.8 v, v mode2 = +1.8 v leakage current - 10 e a v batt = +4.2 v, v cc = +4.2 v, v en = 0 v, v mode = 0 v, v mode1 = 0 v noise in receive band - -134 - gp+ 0+wr0+ harmonic 2 fo 3 fo, 4 fo - - -46 -50 -35 -42 dbc p out 6 +28.4 dbm coupling factor - 20 - db directivity - 20 - db coupler in_out daisy chain insertion loss - - db 0+wr0+ pin 8 - 6, shutdown mode spurious output level (all spurious outputs) - - -70 dbc p out +28.4 dbm ,qedqgordg65 2wriedqgordg65 applies over all operating conditions load mismatch stress with no permanent degradation or failure - - vswr applies over full operating range
data sheet - rev 2.0 04/2011 awt6625a 5 table 5: electrical specifcations - cdma2000 operation (rc-1 waveform) (t c = +25 c, v batt = v cc = +3.4 v, v enable = +1.8 v, 50 ? system) parameter min typ max unit comments p out v mode1 v mode2 gain 26 15 10 29 18 12.5 31 22 16 db p out = +27.7 dbm p out = +16 dbm p out = +7 dbm 0 v 1.8 v 1.8 v 0 v 0 v 1.8 v adjacent channel power at 885 khz offset (1) primary channel bw = 1.23 mhz adjacent channel bw = 30 khz - - - -50 -50 -51 -46.5 -46.5 -46.5 dbc p out = +27.7 dbm p out = +16 dbm p out = +7 dbm 0 v 1.8 v 1.8 v 0 v 0 v 1.8 v adjacent channel power at 1.98 mhz offset (1) primary channel bw = 1.23 mhz adjacent channel bw = 30 khz - - - -59 -60 -60 -56 -56 -56 dbc p out = +27.7 dbm p out = +16 dbm p out = +7 dbm 0 v 1.8 v 1.8 v 0 v 0 v 1.8 v power-added efficiency (1) 34 19 13 37 23 17 - - - % p out = +27.7 dbm p out = +16 dbm p out = +7 dbm 0 v 1.8 v 1.8 v 0 v 0 v 1.8 v spurious output level (all spurious outputs) - - -70 dbc p o u t < +27.7 dbm in-band load vswr < 5:1 out-of-band load vswr < 10:1 applies over all operating conditions load mismatch stress with no permanent degradation or failure 8:1 - - vswr applies over all operating conditions notes: /5(ffpvu0
6 data sheet - rev 2.0 04/2011 awt6625a application information table 6: bias control figure 3: evaluation board schematic to ensure proper performance, refer to all related application notes on the anadigics web site: http://www.anadigics.com shutdown mode the power amplifer may be placed in a shutdown mode by applying logic low levels (see operating ranges table) to the v en , v mode1 and v mode2 voltages. bias modes the power amplifer may be placed in either low, medium or high bias modes by applying the appropriate logic level (see operating ranges table) to the v mode voltages. the bias control table below lists the recommended modes of operation for various applications. three operating modes are recommended to optimize current consumption. high bias/high power operating mode is for p out levels > 17 dbm. at ~17dbm - 6 dbm, the pa should be mode switched to medium power mode. for p out levels < ~7 dbm, the pa can be switched to low power mode for even lower quiescent current consumption. c3 330 pf c4 2.2 f ceramic rf in 1 6 7 10 8 5 4 3 v batt v mode1 rf out rf in gnd v cc v en cpl out v cc c1 0.01 f v batt v mode 1 v en cpl in v mode 2 2 9 v mode2 c5 2.2 f c2 0.01 f gnd at slug cpl in cpl out rf out c9 100 pf application p out levels bias mode v en v mode1 v mode2 v cc v b at t low power (low bias mode) ? +8 dbm low +1.8 v +1.8 v +1.8 v 3.2 - 4.35 v > 3.2 v med power (medium bias mode) > 8 dbm ? +17 dbm low +1.8 v +1.8 v 0 v 3.2 - 4.35 v > 3.2 v high power (high bias mode) > +17 dbm high +1.8 v 0 v 0 v 3.2 - 4.35 v > 3.2 v shutdown - shutdown 0 v 0 v 0 v 3.2 - 4.35 v > 3.2 v
data sheet - rev 2.0 04/2011 awt6625a 7 figure 4: m45 package outline - 10 pin 3 mm x 3 mm x 1 mm surface mount module figure 5: branding specifcation - m45 package package outline 6625a llllnn yy wwc c pin 1 identifier co untr y co de(c c) pa rt number date co de (y yw w) lo t number
8 data sheet - rev 2.0 04/2011 awt6625a component packaging figure 6: tape & reel packaging table 7: tape & reel dimensions pin 1 package type tape width pocket pitch reel capacity max reel dia 3 mm x 3 mm x 1 mm 12 mm 4 mm 2500 7"
warning anadigics products are not intended for use in life support appliances, devices or systems. use of an anadigics product in any such application without written consent is prohibited. important notice anadigics 141 mount bethel road warren, new jersey 07059, u.s.a. tel: +1 (908) 668-5000 fax: +1 (908) 668-5132 url: http://www.anadigics.com anadigics, inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. the product specifcations contained in advanced product information sheets and preliminary data sheets are subject to change prior to a products formal introduction. information in data sheets have been carefully checked and are assumed to be reliable; however, anadigics assumes no responsibilities for inaccuracies. anadigics strongly urges customers to verify that the information they are using is current before placing orders. data sheet - rev 2.0 04/2011 9 awt6625a ordering information order number temperature range package description component packaging awt6625arm45q7 -30 o c to +90 o c rohs compliant 10 pin 3 mm x 3 mm x 1 mm surface mount module tape and reel, 2500 pieces per reel awt6625ARM45P9 -30 o c to +90 o c rohs compliant 10 pin 3 mm x 3 mm x 1 mm surface mount module partial tape and reel
|
