do not scale from this print ((no of positions / 20) x .7875[20.003]) + .0500[1.270] ref .285 7.24 ref .6250 15.875 ref .0060 ref 0.152 @ .0315 [.800] 19 eq. spaces .0225 0.571 ref .7875 20.003 .0975 2.477 ref .1195 3.035 ref c 01 02 qse-xxx-01-xxx-d-xxx no of positions -020, -040, -060 *-080, *-100 (per row) row specification -d: double (use qse-20-xx-d-xx) option plating specification lead style -01 .1280[3.251] no of banks -a: alignment pins (use qse-20-xx-d-xx-a) na with -lc option -lc: locking clips(see note 14) (use lc-08-tm-01, ) na with -a option -gp: guide posts (see fig 3, sht 2) (use qse-20-01-d-xx-x-gp) (t & r packaging: 40 pos max) -k: polyimide film (use k-dot-.325-.450-.005, see fig 2, sht 2) -tr: tape & reel (60 pos max) (40 pos max -gp option) -fl: friction locks (see fig 4, sht 2) (not available with -gp) -rt1: retention option (must use -a option) (use qse-20-01-d-xx-a-rt1 & sub-sc-05-01-ff) (see fig 5, sht 2) (not available with -lc, -gp, or -fl) (not available with -100 pos) -l: latching option (40 pos max) (see fig 6, sht3) (must use -a option) (not available with -lc, -gp, -fl, or -rt1) plating thicknesses are for signal pins only. for ground plane thicknesses, see pp-t-1g2-xx-x. (see notes 8, 11 & 13) -f: 3" selective gold contact, matte tin tail (use c-126-21-f, t-1g2-01-f) -l: 10" selective gold contact, matte tin tail (use c-126-21-l, t-1g2-01-l) -h: 30" gold contact, 3" gold tail (use c-126-21-h, t-1g2-01-g) -c: 50" electro polished selective gold contact, matte tin tail (use c-126-21-c, t-1g2-01-l) -stl: 30" selective gold contact, tin lead (90/10 5%) tails (use c-126-21-stl, t-1g2-01-stl) -ftl: 3" selective gold contact, tin lead (90/10 5%) tails (use c-126-21-ftl, t-1g2-01-ftl) -ltl: 10" selective gold contact, tin lead (90/10 5%) tails (use c-126-21-ltl, t-1g2-01-ltl) -s: 30" selective gold contact, matte tin tail (use c-126-21-s, t-1g2-01-l) * see note 12 .055 1.40 .7250 ref 18.415 .120 3.05 ref .010 ref 0.25 "a" "a" qse-20-01-d-xx-x fig 1 qse-060-01-xxx-d-lc shown lc-08-tm-01 see note 15 .007 0.18 ref .0375 0.953 (((no of positions / 20) x .7875[20.003]) + .005[.13]) .003 t-1g2-01-xxx .0350 ref 0.889 .0375 0.953 ref (((no of positions / 20) x .7875[20.003]) +.005[.13]) ref -a: alignment pin option shown .056 ref 1.42 .1280 - .0010 + .0030 3.251 - 0.025 + 0.076 (see note 6 & 7) .2950 ref 7.493 section "a"-"a" c c-126-21-xxx (see note 13) c ay see table 1 .0375 0.953 ref r c sheet of unless otherwise specified, dimensions are in inches. tolerances are: decimals angles .xx: .01[.3] 2 .xxx: .005[.13] .xxxx: .0020[.051] material: .8mm double row hs socket assembly by: qse-xxx-01-xxx-d-xxx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing eric m 05/20/1999 3 1 sheet scale: 2:1 insulator: lcp, color: black, ul 94 vo contact: phos bronze ground plane: phos bronze f:\dwg\misc\mktg\qse-xxx-01-xxx-d-xxx-mkt.slddrw notes: 1. represents a critical dimension. 2. min contact retention: 8 oz 3. min ground plane retention: 8 oz 4. parts are molded to position. 5. deleted. 6. max variance: .002[0.51]. 7. dimension applies to contacts & ground plane. 8. -l plating can be substituted for -f plating, -g plated ground plane can be substituted for -f plated ground plane. 9. ground plane press height must be .003 [0.08] less than the max height or .001 [0.03] greater than the minimum height of the sockets. 10. s-103 retention: 1 lb min in body. 11. may sub c-126-01-xxx for c-126-21-xxx. 12. for new applications requiring these positions, please contact samtec interconnect processing group. 13. for -080, -100 positions use c-269-11-xxx. do not sub c-126. 14. due to the high amount of insertion force needed, the -lc option is not compatible with auto placement.samtec recommends manual placement for all assemblies with the -lc option. 15. side walls are ribbed as necessary to control bow. 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322 revision ay
"r" ref .325 8.26 "s" .020 0.51 fig 2 -k: polyimide film pad note: "r" = ((no of positions / 20) x .7875[20.003]) + .050[1.27] with -gp option: "r" = ((no of positions / 20) x .7875[20.003]) + .429[10.90] ref "s" = (("r" - .325[8.26]) / 2) .020[.51] [ k-dot-.325-.450-.005] .133 3.378 qse-20-01-d-xx-a-gp -gp option (same as fig. 1, unless otherwise stated) [available on lead style -01 & -01-a only] (40 pos. max with t & r packaging) fig 3 ((no of positions/20) x .7875[20.003]) + .225[5.72] ref .102 ref 2.58 .1400 thru ref 3.556 ((no of positions / 20) x .7875[20.003]) + .429[10.90] ref .207 ref 5.26 .7875[20.003]) + .0600[1.524] ref ((no of positions / 20) x "b" "b" -fl: friction locks (not available with -gp option) (same as fig 1, unless otherwise stated) fig 4 qse-20-01-d-xx-fl 'c' section "b"-"b" .080 2.03 ref (typ) .026 0.66 ref (typ) detail 'c' scale 8 : 1 ((no of positions/20) x .7875[20.003]) + .650[16.51] ref (((no of positions/20) x .7875[20.003]) + .341[8.66]) .003[0.08] "d" "d" -rt1: retention option (must use -a option) (not available with -lc, -gp, or -fl options) (not available with -100 pos) (same as fig 1, unless otherwise stated) fig 5 qse-20-01-d-xx-a-rt1 c .148 ref 3.76 (((no of positions/20) x .7875[20.003]) + .341[8.66]) .003[0.08] 'e' section "d"-"d" scale 1.5 : 1 sub-sc-05-01-ff (2 plcs) c .045 ref 1.14 .150 3.81 detail 'e' scale 3 : 1 c sheet of .8mm double row hs socket assembly by: qse-xxx-01-xxx-d-xxx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing eric m 05/20/1999 3 2 sheet scale: 2:1 revision ay f:\dwg\misc\mktg\qse-xxx-01-xxx-d-xxx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322
.053 .002 1.35 0.051 .010 ref 0.25 .160 ref 4.06 ((no of positions / 20) x .7875[20.003]) + .1715[4.356] qse-20-01-d-xx-a-l wt-56-01-t c c ((no of positions / 20) x .7875[20.003]) + .2600[6.604] ref .0300 ref 0.762 ((no of positions / 20) x .7875[20.003]) + .1093[2.776] fig 6 -l: latching option (must use -a option) (same as fig 1, unless otherwise stated) (not available with -lc, -gp, -fl, or -rt1) (maximum 40 pos) c .025 ref 0.64 ay critical dimension inspection instruction table assembly operation in-process inspection fill c-126-21 c1, c2, c3 add -rt1 option c4, c5, c6 add -l option c7, c8, c9 sheet of .8mm double row hs socket assembly by: qse-xxx-01-xxx-d-xxx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing eric m 05/20/1999 3 3 sheet scale: 2:1 revision ay f:\dwg\misc\mktg\qse-xxx-01-xxx-d-xxx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322
|
