do not scale from this print .138 ref .020 ref .008 ref .050 (typ) 2 max sway (typ) ({(no. of pos - 2) x .100} .005 2 max sway (typ) "a" "a" (shown with -lc option) no of pos. x .100 - .005 + .008 .200 ref .100 ref (no of pos. -1) x .100 c1 02 01 hle-1xx-02-xx-dv-xe-xx no of positions -02 thru -50 (per row) row specification -dv: double vertical (use rhle-50-dxx) plating specification -g: gold (see table 1) -l: light selective gold, matte tin tail (see table 1) -s: selective gold, matte tin tail (see table 1) -lm: light selective gold, matte tin tail (see table 1) -sm: selective gold, matte tin tail (see table 1) -f: flash selective gold, matte tin tail (see table 1) entry style -pe: pass through entry (see fig. 1) -te: top entry (see fig. 2) lead style -02 option -be: bottom entry (use rhle-50-dbe) (see fig. 3) (available on -pe style only) -lc: locking clip (see note 10) (use lc-08-tm-01) (available on -pe style only) -tr: tape & reel (2 - 29 positions only) (-te & -pe options only) -p: metal pad (use mpp-02) (see fig. 2) x (see section "a"-"a", sht 2 for dimensions) figure 1 (-pe: pass through entry) c x sheet of unless otherwise specified, dimensions are in inches. tolerances are: decimals angles .xx: .01 2 .xxx: .005 .xxxx: .0020 material: .100 c.l. single beam socket strip by: hle-1xx-02-xx-dv-xe-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing kevin b 10/27/99 2 1 sheet scale: 2:1 body: vectra e130i color: black contact: becu f:\dwg\misc\mktg\hle-1xx-02-xx-dv-xe-xx-mkt.slddrw notes: 1. represents a critical dimension. 2. cut assemblies after fill. cut flash to be .010 max with no flash allowed in holes or extending below leads. will lose a position for every cut. 3. tube positions 03 thru 50. layer package position 02. 4. endwall thickness: .030 .003. 5. minimum contact retention in plastic: 12 ounces 6. after plating, pin is named sub-c-132-10-x. after forming, pin is c-132-10-x 7. max variation of 3 degrees within 16 pins. 8. measure from bend to tip of pin. 9. measure from contact barb area to tip of pin 10. due to the high amount of insertion force needed, the -lc option is not compatible with auto placement, samtec recommends manual placement for all assemblies with the -lc option. 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322 revision x
packaging views figure 3 (bottom entry option) .280 ref "p"/2 -.1125 .010 .225 ref "p" .146 figure 2 (-te with -p option) .120 .100 90 - 2 + 4 c6 c5 see table 1 .006 ref .056 ref (typ.) .090 .144 - .000 + .010 (typ.) .300 - .010 + .015 90 3 section "a"-"a" scale 4 : 1 c2 c4 c3 see table 1 measure over bend closest to the body notes: 1. note deleted. 2. note deleted. 3. note deleted. 4. note deleted. sheet of .100 c.l. single beam socket strip by: hle-1xx-02-xx-dv-xe-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. kevin b 10/27/99 2 2 sheet scale: 2:1 f:\dwg\misc\mktg\hle-1xx-02-xx-dv-xe-xx-mkt.slddrw revision x 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
|
