series am ldv -nz up to 700ma | led dr iver www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r12 .c 1 of 8 north america only features: models single output model input voltage (v) output voltage (v) maximum rated current (ma) efficiency max (%) amld v - 4830 - nz 5.5 - 48 3.3 - 36 300 96 amldv - 4835 - nz 5.5 - 48 3.3 - 36 350 96 amldv - 4850 - nz 5.5 - 48 3.3 - 36 500 96 amldv - 4860 - nz 5.5 - 48 3.3 - 36 600 96 amldv - 4870 - nz 5.5 - 48 3.3 - 36 700 96 note: all specifications in this datasheet are measured at an ambient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. input specifications parameters nominal typical maxim um units voltage range 24 5.5 - 48 vdc absolute maximum rating( 10sec) 5 - 55 vdc on/off control (analog control) (leave open if not used) on: open or 2.8v> v <6 v off: v <0.6 v remote pin current v=5v 1 ma quiescent input current in shutdown mode vin=24v, v<0.6v 400 a dimming control (digital control) max pwm frequency: 200hz dimming control (analog control) (leave open if not used) input voltage range (vin=5.5 - 48v) output current range(vin=5.5 - 48v) 0 - 15v 0 - 100% control voltage range(full on) control voltage range(full off) 0.2v50mv 4.5v50mv drivin g current(v=5v) 0. 6 ma(max) input filter capacitor output specifications parameters conditions typical maximum units current accuracy 2 3 % short circuit protection continuous, automatic recovery efficiency at full load 96 % max load capacitance 100 0 f ripple & noise 20mhz bandwidth 120 mv p - p temperature coefficient - 40 o c to+71 o c 0.015 %/oc output current stability vin=48v, vo=3.3~36v 1 % internal power dissipation vin=24v,5leds 700 mw general specifications parameters conditions typical maximum units switching frequency 100 % load 370 320 - 420 khz operating temperature 300ma,350ma - 40 to +85 o c 500ma,600ma,700ma - 40 to+71 o c storage temperature - 55 to +125 o c max case temperature 100 o c cooling free air convection humidi ty 95 % rh ? high power led driver ? constant current output mode ? ultra wide input voltage range ? high efficiency (up to 96%) ? remote on/off function ? pwm & analogue dimming function ? smd package ? operating temperature range - 40o c - +85oc
series am ldv -nz up to 700ma | led dr iver www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r12 .c 2 of 8 north america only general specifications (continued) parameters conditions typical maximum units case material plastic ul94 - vo potting material epoxy resin(flammability ul94v - 0) weight 6 g dimensions (l x w x h) 0.939 0.713 0.315 inches 23.86 18.10 8.00 mm mtbf >2 00 0 000 hrs (mil - hdbk - 217 f at +25 o c) safety specifications parameters standards designed to meet: en 55022 , class b , iec /en 61000 - 4 - 2 ( perf. criteria b) , iec /en 61000 - 4 - 3 ( perf. criteria b ) , iec /en 61000 - 4 - 4 ( perf. criteria b ) , iec /en 61000 - 4 - 5 ( perf. criteria b ) , iec/en 61000 - 4 - 5 ( perf. criteria b) pin out specifications dimensions 18.10 (0.71) 7.50 (0.30) top view side view 8.00 (0.32) 1 7 9 10 16 23.86 (0.94) 1.02 (0.04) 2.54 (0.10) 8 13.70 (0.54) 3.04 (0.12) a 1.40 0.20 (0.055 0.008) max 0.25 (0.01) 5.00o max a 0.25 (0.01) front view pin single 1 - v input dc supply 7 remote on/off pwm dimming pwm/on/off or not used 8 - v output led cathode connection 9 +v output led anode connec tion 10 analogue dimming analogue dimming or not used 16 +v i n put + dc supply
series am ldv -nz up to 700ma | led dr iver www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r12 .c 3 of 8 north america only derating free air convection - 40 - 20 0 20 40 60 80 100 100 80 60 40 20 0 safe operating area output power (%) 85 ambient temperature o c 71 amldv - 3030 - nz amldv - 3035 - nz amldv - 3050 - nz amldv - 3060 - nz amldv - 3070 - nz typical application circuits amldv-nz -vin pwm dimming on/off +vout 1 1 -vout +vin 1 16 10 7 analogue dimming 8 9 1 st led last led 1 1 1 1 amldv-nz -vin pwm dimming on/off +vout -vout +vin 1 16 10 7 analogue dimming 8 9 series configuration parallel-series configuration
series am ldv -nz up to 700ma | led dr iver www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r12 .c 4 of 8 north america only pwm dimming control iout _ nominal iout _ set = ( dt - 0 . 6 ) t [ [ where : d is pulse width t is cycle of the pulse note: formula is for reference; actual output current may depend on loading. t he time on of pulse must be > 0. 7ms analogue dimming control pwm digital control signal 1 0 1 0 output current 1 0 1 0 output current leds appear dim pwm digital control signal 1 0 1 0 output current leds appear bright pwm digital control signal amldv - nz - vin + vout 1 1 - vout + vin 1 16 10 8 9 0 to 10 vdc 5. 6k 5. 1k 7 on / off ( optional )
series am ldv -nz up to 700ma | led dr iver www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r12 .c 5 of 8 north america only recommended emc circuit amldv-nz -vin pwm dimming on/off +vout 1 1 -vout +vin 1 16 10 7 analogue dimming 8 9 1.0 f 1.0 f 1,25mh 2.2 f 470 f 1 smcg51 recommended ac input circuit amldv - nz - vin pwm dimming on / off + vout 1 1 - vout 1 16 10 7 analogue dimming 8 9 + ac in ac in 5 vac to 32 vac - 0 . 1 uf optional 100 uf to 330 uf + vin
series am ldv -nz up to 700ma | led dr iver www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r12 .c 6 of 8 north america only efficiency versus input voltage
series am ldv -nz up to 700ma | led dr iver www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r12 .c 7 of 8 north america only
series am ldv -nz up to 700ma | led dr iver www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r12 .c 8 of 8 north america only o utput c urrent versus d imming v oltage note: 1. datasheets are updated as needed and as such, specifications are subject to change with out notice. once printed or downloaded, datasheets are no longer controlled by aimtec; refer to www.aimtec.com for the most current product specifications. 2. product labels shown, including safety agency certifications on labels, may vary based on the d ate manufactured. 3. mechanical drawings and specifications are for reference only. 4. all specifications are measured at an ambient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specifie d. 5. aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. cas numbers and other limited information are considered proprietary and may not be available for release. 6. this product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control s ystems or other such applica tions which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. warranty is in accordance with aimtecs standard terms of sale available at www.aimtec.com.
|
