e j g k b a d c ? h catalog # a b c d e f g h j k j 410/j 411 0.41 0.25 0.19 0.09 0.10 0.04 0.010 0.094 0.08 na j 600 0.62 0.38 0.25 0.12 0.16 0.04 0.015 0.156 0.08 na j 601 0.71 0.45 0.31 0.15 0.19 0.06 0.015 0.166 0.11 na j 602 0.91 0.56 0.37 0.18 0.27 0.08 0.015 0.190 0.16 na j 603 1.13 0.69 0.43 0.21 0.25 0.12 0.031 0.201 0.24 na j 604 1.38 0.88 0.50 0.25 0.35 0.15 0.035 0.234 0.32 na j 605 1.75 1.13 0.62 0.31 0.39 0.24 0.035 0.266 0.54 na j 621 0.69 0.44 0.30 0.17 0.38 0.07 0.015 0.141 0.11 0.14 js 600 0.62 0.38 0.25 0.12 0.16 0.04 0.015 0.156 0.08 0.16 js 601 0.71 0.45 0.31 0.15 0.19 0.06 0.015 0.166 0.11 0.17 js 602 0.91 0.56 0.37 0.18 0.27 0.08 0.015 0.190 0.16 0.14 catalog # material finish screw thread l a 3786 steel nickel 8-32 unc 0.38 0.41 3765 6-32 unc 0.31 0.33 3780 brass nickel 8-32 unc 0.38 0.41 3760 6-32 unc 0.31 0.33 3860 brass nickel 6-32 unc 0.30 0.29 3865 steel nickel 6-32 unc 0.30 0.29 107 terminal block accessories terminal block accessories datasheets available at marathonsp.com j & js jumpers mm = dim x 25.4 note 1: these parts are not necessarilty supplied flat. the functioning of the part, however, will not be interferred. msp catalog designations: j 600 = ll 100 j 601 = ll 200 j 602 = ll 300 j 603 = ll 400 j type jumper js type jumper (per 55164/28b) rj type jumpers straddle plate wire clamp rjs type jumpers .23 [5.9] .72 [18.3] .17 [4.3] .14 [3.6] .12 [3.0] .38 [9.5] .52 [13.2] .28 [7.1] .65 [16.5] .16 [4.0] .15 [3.8] .032 [.81] .031 [.79] .14 [3.6] .44 [11.1] ? .15 [3.8] ? .16 [4.0] .28 [7.1] .16 [4.0] .19 [4.9] r .078 [1.98] .08 [2.0] .437 [11.10] .14 [3.6] .71 [18.1] .031 [.79] r .07 [1.8] .28 [7.1] .14 [3.6] .14 [3.6] .374 [9.50] .18 [4.6] .031 [.79] .45 [11.4] .56 [14.2] .25 [6.4] .26 [6.6] phil-slot a a l screw thread a b c d ? f ? e material: brass finish: nickel plate 600 rj max # of sections = 24 note: 670a rz, 599 series, use 600 rj 601 rj max # of sections = 24 material: brass finish: nickel plate 600 rjs max # of sections = 24 note: 670a rz, 599 series, use 600 rj 601 rjs max # of sections = 24 note: termi-lox washer or equal mm = dim x 25.4 mm = dim x 25.4 catalog # a b c d e f material finish spb 600 0.56 0.31 0.30 0.032 0.144 n/a brass tin spb 601 0.71 0.42 0.30 0.031 0.148 n/a brass nickel spb 602 0.8 7 0.50 0.40 0.032 0.189 n/a brass nickel spb 603 1.03 0.62 0.45 0.063 0.190 0.143 brass tin spb 604 1.21 0.75 0.54 0.087 0.187 0.138 brass tin spb 605 1.46 0.87 0.63 0.116 0.220 0.138 brass nickel note 2: all dimensions are applicable after the bus (jumper) is torqued down into the associate terminal board. material: brass finish: nickel plate
|