a~~=p a~~=p ?? epcos ag 2011. reproduction, publication and di ssemination of this publication, enclosures hereto and the information contained therein wit hout epcos? prior expres s consent is prohibited. power line chokes current-compensated fr ame core double chokes 250 v ac, 0.7 ? 2.3 a, 10 ? 100 mh, +40 c series/type: b82733f date: march 2011
2 03/11 please read cautions and warnings and important notes at the end of this document. rated voltage 250 v ac rated current 0.7 a to 2.3 a rated inductance 10 mh to 100 mh construction current-compensated frame core double choke closed magnetic circuit with fram e construction made of ferrite pet coil former (ul94 v-0) 4-section winding with direct winding on the core sector winding clearance and creepage distances >3 mm features high inductance with low resistance approx. 2% stray inductance for sy mmetrical interfer ence suppression high pulse-handling capability very good inductance/rated current ratio low height (14 mm) suitable for wave soldering design complies with en 60938-2 (vde 0565-2) and ul 1283 enec (vde) and ul 1 approval rohs-compatible 1 ul approval with 300 v ac applications suppression of common-mode and differential-mode interferences electronic ballasts for lamps high power switch-mode power supplies for consumer electronics terminals base material cp wire layer composition ni, sn hot dipped pins 0.7 ? 0.7 mm lead spacing 20 ? 22.5 mm marking manufacturer, date of manufacture (yyww), factory identification code, ordering code, approval signs delivery mode polystyrene tray, anti-static, in cardboard box b82733f power line chokes current-compensated frame core double chokes
3 03/11 please read cautions and warnings and important notes at the end of this document. dimensional drawing and layout recommendation technical data and measuring conditions rated voltage v r 250 v ac (50/60 hz) test voltage v test 1500 v ac, 2 s (line/line) rated temperature t r +40 ? c rated current i r referred to 50 hz and rated temperature rated inductance l r measured with agilent 4284a at 10 khz, 0.1 ma, +20 c. inductance is specified per winding. inductance tolerance ?30/+50% at +20 c inductance decrease ?? l/l 0 <10% at dc magnetic bias with i r , +20 c stray inductance l stray,typ measured with agilent 4284a at 10 khz, 5 ma, +20 c, typical values dc resistance r typ measured at +20 c; typical values, specified per winding solderability (lead-free) sn96.5ag3.0cu0.5: (+245 ? 5) c, (3 ? 0.3) s wetting of soldering area ?? 95% (to iec 60068-2-20, test ta) resistance to soldering heat (wave soldering) (+260 ? 5) c, (10 ? 1) s (to iec 60068-2-20, test tb) climatic category 40/125/56 (to iec 60068-1) storage conditions (packaged) ?25 c ? +40 c, ?? 75% rh weight approx. 18 g approvals en 60938-2, ul 1283 dimensions in mm b82733f power line chokes current-compensated frame core double chokes
4 03/11 please read cautions and warnings and important notes at the end of this document. characteristics and ordering codes ? = approval granted i r a l r mh l stray,typ ? h r typ m ? ordering code approvals 0.7 100 2100 1810 b82733f2701b001 ?? 0.9 68 1440 1100 b82733f2901b001 ?? 1.1 47 970 804 b82733f2112b001 ?? 1.2 39 800 696 b82733f2122b001 ?? 1.4 27 530 440 b82733f2142b001 ?? 1.9 15 310 279 b82733f2192b001 ?? 2.3 10 200 188 B82733F2232B001 ?? impedance |z| versus frequency f measured with windings in parallel at 20 c, typical values current derating i op /i r versus ambient temperature t a | z | f ind0566-r 2 10 3 10 10 4 10 5 10 6 10 7 4 10 10 5 10 6 10 7 hz f2142b001 f2192b001 f2232b001 b82733 f2122b001 f2112b001 f2901b001 f2701b001 b82733f power line chokes current-compensated frame core double chokes
5 03/11 cautions and warnings please note the recommendations in our inducto rs data book (latest edition) and in the data sheets. ? particular attention should be paid to the derat ing curves given there. derating must be applied in case the ambient temperature in the application exceeds the rated temperature of the component. ? ensure the operation temperature (which is the sum of the ambient temperature and the temperature rise caused by loss es / self-heating) of the component in the application does not exceed the maximum value specifi ed in the climatic category. ? the soldering conditions should also be observed. temperat ures quoted in relation to wave soldering refer to the pin, not the housing. if the components are to be washed varnished it is necessary to check whether the washing varnish agent that is used has a negative effect on the wire insulation, any plastics that are used, or on glued joints. in particular, it is possible for washing varnish agent residues to have a negative effect in the long-term on wire insulation. the following points must be observed if the components are potted in customer applications: ? many potting materials shrink as they harden. t hey therefore exert a pr essure on the plastic housing or core. this pressure can have a delet erious effect on electr ical properties, and in extreme cases can damage the core or plastic housing mechanically. ? it is necessary to check whether the potting material used attacks or destroys the wire insulation, plastics or glue. ? the effect of the potting material can chan ge the high-frequency behaviour of the components. ferrites are sensitive to direct impact. this c an cause the core material to flake, or lead to breakage of the core. even for customer-specific produc ts, conclusive validation of t he component in the circuit can only be carried out by the customer. please read cautions and warnings and important notes at the end of this document.
6 03/11 important notes the following applies to all produc ts named in this publication: 1. some parts of this publication contain statements about the suitability of our products for certain areas of application . these statements are based on our knowledge of typical requirements that are often placed on our produc ts in the areas of application concerned. we nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our produc ts for a particular customer application. as a rule, epcos is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. for these reasons , it is always ultimately incumbent on the customer to check and decide whether an epcos product with the properties described in the product specification is suitable for us e in a particular customer application. 2. we also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. in customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic com ponent could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other acti on taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. the warnings, cautions and product-specific notes must be observed . 4. in order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous) . useful information on this will be found in our material data sheets on the internet (www .epcos.com/material). should you have any more detailed questions, please contact our sales offices. 5. we constantly strive to improve our products. consequently, the products described in this publication may change from time to time . the same is true of the corresponding product specifications. please c heck therefore to what extent pr oduct descriptions and specifications contained in this publicati on are still applicable before or when you place an order. we also reserve the right to discontinue production and delivery of products . consequently, we cannot guarantee that all produc ts named in this publication will always be available. the aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 6. unless otherwise agreed in individual contracts, all orders are subject to the current version of the ?general terms of delivery for products and services in the electrical industry? published by the german electrical and electronics industry association (zvei) . 7. the trade names epcos, baoke, alu-x, ceradiode, csmp, cssp, ctvs, deltacap, digisimic, dssp, miniblue, minicell, mkk, mlsc, motorcap, pcc, phasecap, phasecube, phasemod, phicap, siferrit, sifi, sikore l, silvercap, simdad, simic, simid, sineformer, siov, sip5d, sip5k, thermofuse, windcap are trademarks registered or pending in europe and in other countries. further information will be found on the internet at www.epcos.com/trademarks.
|
