mw153kb universal 25-40 watt series line and load line voltage +/-1% regulation (excluding cord) load voltage +/-5% ripple 1% vp-p max. transient response 0.5ms for 50% load change typical protection over-current protection (hiccup) short circuit protection output specifcations input voltage range universal input 100-240vac -10%, +10% line frequency 47-63hz input current 90vac input 0.4a max. protection internal primary current fuse, inrush limiting input specifcations thermal performance operating temperature 0 c to 40 c full load, no derating convectional cooling non vented case relative humidity non-condensing 5% to 95% altitude 0-10,000 feet environmental specifcations topology switching-fixed frequency flyback effciency designed to meet eisa requirements see reverse side hold-up time @115vac 18ms min. dielectric withstand 4,000vac or 5,656vdc primary - secondary; 1,500vac or 2,150vdc primary-f.g; 500vdc secondary-f.g storage temp -30 c to 85 c approvals and ul60601-1 safety standards iec/en60601-1 emc : en60601-1-2/en55024 mtbf 100,000 calculated hours case and dimension desktop style 3.98l x 2.4w x 1.34h (in) 101l x 61w x 34h (mm) case material black 94v0 polycarbonate cord and connectors 18 awg 1,500mm 2 conductor. ault #3 connector. other connectors are also available. general specifcations specifcations sl power electronics corp ? 6050 king drive ? ventura, ca 93003 ? phone:805.486.4565 ? fax:858.712.2040 ? email:info@slpower.com ? www.slpower.com ? 100-240 vac universal input ? desktop style ? single output to 40w ? four models available; 12v to 24v ? regulated output with low ripple ? impact resistant polycarbonate enclosure ? modifed and custom designs also available ? designed to meet eisa requirements see reverse side for details international safety standard approvals
mw153kb universal 25-40 watt series output max ripple ault part number voltage max watts vp-p max. MW153KB12XX 12 v 3.40 a 40.8 w 120 mv mw153kb15xx 15 v 2.70 a 40.5 w 150 mv mw153kb18xx 18 v 2.20 a 39.6 w 180 mv mw153kb24xx 24 v 1.70 a 40.8 w 240 mv output current mw153 k b 12 xx product manufacturing design voltage connector family location revision dc number name changes ault part number key pinout code center contact: positive description switchcraft 760 plug or equivalent suggested mating switchcraft 712a jack or equivalent other connectors are available by special order pin connections sl power electronics corp ? 6050 king drive ? ventura, ca 93003 ? phone:805.486.4565 ? fax:858.712.2040 ? email:info@slpower.com ? www.slpower.com data sheet ? 2008 sl power electronics corp. the information and specifcations contained in this data sheet are believed to be correct at time of publication. however, sl power accepts no responsibility for consequences arising from reproduction errors or inaccuracies. specifcations are subject to change without notice. rev.6/9/08 for the most current data and application support visit www.slpower.com the energy independence and security act of 2007 was passed in december of 2007 and addresses minimum effciency standards and standby levels for class a external power supplies that are 250 watts and under. this law stipulates that external power supplies manufactured on july 1, 2008 and beyond meet certain minimum effciency and standby criteria as defned below. minimum effciency criteria active mode is defned as when a power supplys input is connected to line voltage ac and its output is connected to a dc or ac load drawing a portion of the products power output. depending on the power rating for the power supply, it must meet the minimum effciency criteria outlined below. energy-effciency criteria for active mode: output power on minimum average adapter label effciency percentage 0 to less than 1 watt 0.50 * output power on adapter label > 1 to 51 watts [0.09 * ln (output power on adapter label )] + 0.50 > 51 watts 0.85 the power supply must also meet a requirement for when its input is connected to a line voltage ac but its output is not connected to a load. depending on the power output of the supply, it must keep its energy consumption below the following values. energy consumption criteria for no load mode: output power on maximum power consumption adapter label in no-load mode 0 to < 250 watts 0.5 watts 2007 energy independence and security act C eisa specify the input confguration code in your order. input confguration shaver c8 (n) iec320 w /ground c14 (f) iec320 w /o ground c18 (q) australian (e) n. america/ japan (b) europe (m ) united kingdom (g) shaver c8 (n) iec320 w /ground c14 (f) iec320 w /o ground c18 (q) australian (e) n. america/ japan (b) europe (m ) united kingdom (g)
|
