ta48l018,02,025,03,033,05f 2003-01-15 1 toshiba bipolar linear integrated circuit silicon monolithic TA48L018F,ta48l02f,ta48l025f,ta48l03f,ta48l033f,ta48l05f 1.8 v, 2 v, 2.5 v, 3 v, 3.3 v, 5 v three-terminal low dropout voltage regulator with output current of 0.15 a the ta48l ** f series consists of fixed-positive-output, low-dropout regulators and v-pnp transistors for output stage with an output current of 1 a (max). in response to the need for low-voltage and low-power dissipation devices which are used in consumer electronics and industrial appliances, the series offers devices with low output voltages: 1.8 v, 2 v, 2.5 v, 3 v, 3.3 v, 5 v. features maximum output current: 0.15 a output voltage accuracy: v out 3% (@t j = 25c) low standby current: 400 a (typ.) (@i out = 0 a) low-dropout voltage: v d = 0.5 v (max) (@i out = 100 ma) protection function: overheat/overcurrent package type: pw-mini (sot-89) package pin assignment/marking product name marking (two digits) TA48L018F ai ta48l02f bi ta48l025f ci ta48l03f di ta48l033f ei ta48l05f fi weight: 0.05 g (typ.) 2 1 3 lot no. (three digits) marking (two digits) the week of manufacture the year of manufacture (last decimal digit of the year of manufacture) 3 1: in 2: out 3: gnd
ta48l018,02,025,03,033,05f 2003-01-15 2 how to order product no. package packing type and unit for orders ta48l ** f on cut tape (te12l): 100/tape section ta48l ** f (te12l) pw-mini (sot-89) surface-mount package embossed tape: 1000 pcs/tape block diagram maximum ratings (ta 25c) characteristics symbol rating unit input voltage v in 16 v output current i out 0.15 a operating temperature t opr 40~85 c junction temperature t j 150 c storage temperature t stg 55~150 c power dissipation p d 0.5 w thermal resistance (junction to ambient) p th(j-a) 250 c/w note 1: must not to apply external current and voltage (including negative voltage) to not specified pins. protection function (reference) characteristics symbol test condition min typ. max unit thermal shutdown t sd (t j ) 160 c peak circuit current i peak v in v out 2 v, t j 25c 0.27 a short circuit current i sc v in v out 2 v, t j 25c 0.27 a note 2: when the ic is actually used, must not exceed maximum ratings. 1in 2out 3gnd reference voltage over current protection thermal shut down protection
ta48l018,02,025,03,033,05f 2003-01-15 3 TA48L018F electrical characteristics (c in 0.33 f, c out 3.3 f, t j 25c, unless otherwise specified) characteristics symbol test conditions min typ. max unit v in 3.8 v, i out 40 ma 1.746 1.8 1.854 output voltage v out 2.8 v v in 12 v, 5 ma i out 100 ma, 0c t j 125c 1.71 1.8 1.89 v line regulation reg line 2.8 v v in 12 v, i out 40 ma 2 20 mv load regulation reg load v in 3.8 v, 5 ma i out 150 ma 18 40 mv 2.8 v v in 12 v, i out 0 a 0.4 0.8 quiescent current i b 2.8 v v in 12 v, i out 100 ma 1 5 ma v in 2.1 v, i out 0 a 0.5 1.5 starting quiescent current i bstart v in 2.1 v, i out 100 ma 5 20 ma output noise voltage v no v in 3.8 v, i out 40 ma, 10 hz f 100 khz 45 vrms ripple rejection r.r. 2.8 v v in 12 v, i out 40 ma, f 120 hz 54 72 db i out 40 ma 0.28 0.4 dropout voltage v d i out 100 ma 0.32 0.5 v average temperature coefficient of output voltage t cvo v in 3.8 v, i out 5 ma, 0c t j 125c 0.3 mv/c ta48l02f electrical characteristics (c in 0.33 f, c out 3.3 f, t j 25c, unless otherwise specified) characteristics symbol test conditions min typ. max unit v in 4.0 v, i out 40 ma 1.94 2.0 2.06 output voltage v out 3.0 v v in 12 v, 5 ma i out 100 ma, 0c t j 125c 1.90 2.0 2.10 v line regulation reg line 3.0 v v in 12 v, i out 40 ma 2 20 mv load regulation reg load v in 4.0 v, 5 ma i out 150 ma 18 40 mv 3.0 v v in 12 v, i out 0 a 0.4 0.8 quiescent current i b 3.0 v v in 12 v, i out 100 ma 1 5 ma v in 2.1 v, i out 0 a 0.5 1.5 starting quiescent current i bstart v in 2.1 v, i out 100 ma 5 20 ma output noise voltage v no v in 4.0 v, i out 40 ma, 10 hz f 100 khz 55 vrms ripple rejection r.r. 3.0 v v in 12 v, i out 40 ma, f 120 hz 52 70 db i out 40 ma 0.2 0.35 dropout voltage v d i out 100 ma 0.3 0.5 v average temperature coefficient of output voltage t cvo v in 4.0 v, i out 5 ma, 0c t j 125c 0.35 mv/c
ta48l018,02,025,03,033,05f 2003-01-15 4 ta48l025f electrical characteristics (c in 0.33 f, c out 3.3 f, t j 25c, unless otherwise specified) characteristics symbol test conditions min typ. max unit v in 4.5 v, i out 40 ma 2.425 2.5 2.575 output voltage v out 3.5 v v in 12 v, 5 ma i out 100 ma, 0c t j 125c 2.375 2.5 2.625 v line regulation reg line 3.5 v v in 12 v, i out 40 ma 2 20 mv load regulation reg load v in 4.5 v, 5 ma i out 150 ma 18 40 mv 3.5 v v in 12 v, i out 0 a 0.4 0.8 quiescent current i b 3.5 v v in 12 v, i out 100 ma 1 5 ma v in 2.4 v, i out 0 a 0.5 1.5 starting quiescent current i bstart v in 2.4 v, i out 100 ma 7 20 ma output noise voltage v no v in 4.5 v, i out 40 ma, 10 hz f 100 khz 65 vrms ripple rejection r.r. 3.5 v v in 12 v, i out 40 ma, f 120 hz 52 70 db i out 40 ma 0.16 0.35 dropout voltage v d i out 100 ma 0.27 0.5 v average temperature coefficient of output voltage t cvo v in 4.5 v, i out 5 ma, 0c t j 125c 0.45 mv/c ta48l03f electrical characteristics (c in 0.33 f, c out 3.3 f, t j 25c, unless otherwise specified) characteristics symbol test conditions min typ. max unit v in 5.0 v, i out 40 ma 2.91 3.0 3.09 output voltage v out 4.0 v v in 12 v, 5 ma i out 100 ma, 0c t j 125c 2.85 3.0 3.15 v line regulation reg line 4.0 v v in 12 v, i out 40 ma 2 20 mv load regulation reg load v in 5.0 v, 5 ma i out 150 ma 18 40 mv 4.0 v v in 12 v, i out 0 a 0.4 0.8 quiescent current i b 4.0 v v in 12 v, i out 100 ma 1 5 ma v in 2.8 v, i out 0 a 0.5 1.5 starting quiescent current i bstart v in 2.8 v, i out 100 ma 7 20 ma output noise voltage v no v in 5.0 v, i out 40 ma, 10 hz f 100 khz 80 vrms ripple rejection r.r. 4.0 v v in 12 v, i out 40 ma, f 120 hz 50 68 db i out 40 ma 0.16 0.35 dropout voltage v d i out 100 ma 0.27 0.5 v average temperature coefficient of output voltage t cvo v in 5 v, i out 5 ma, 0c t j 125c 0.5 mv/c
ta48l018,02,025,03,033,05f 2003-01-15 5 ta48l033f electrical characteristics (c in 0.33 f, c out 3.3 f, t j 25c, unless otherwise specified) characteristics symbol test conditions min typ. max unit v in 5.3 v, i out 40 ma 3.2 3.3 3.4 output voltage v out 4.3 v v in 12 v, 5 ma i out 100 ma, 0c t j 125c 3.135 3.3 3.465 v line regulation reg line 4.3 v v in 12 v, i out 40 ma 2 20 mv load regulation reg load v in 5.3 v, 5 ma i out 150 ma 18 40 mv 4.3 v v in 12 v, i out 0 a 0.4 0.8 quiescent current i b 4.3 v v in 12 v, i out 100 ma 1 5 ma v in 3.0 v, i out 0 a 0.5 1.5 starting quiescent current i bstart v in 3.0 v, i out 100 ma 7 20 ma output noise voltage v no v in 5.3 v, i out 40 ma, 10 hz f 100 khz 85 vrms ripple rejection r.r. 4.3 v v in 12 v, i out 40 ma, f 120 hz 50 68 db i out 40 ma 0.16 0.35 dropout voltage v d i out 100 ma 0.27 0.5 v average temperature coefficient of output voltage t cvo v in 5.3 v, i out 5 ma, 0c t j 125c 0.55 mv/c ta48l05f electrical characteristics (c in 0.33 f, c out 3.3 f, t j 25c, unless otherwise specified) characteristics symbol test conditions min typ. max unit v in 7.0 v, i out 40 ma 4.85 5.0 5.15 output voltage v out 6.0 v v in 12 v, 5 ma i out 100 ma, 0c t j 125c 4.75 5.0 5.25 v line regulation reg line 6.0 v v in 12 v, i out 40 ma 2 20 mv load regulation reg load v in 7.0 v, 5 ma i out 150 ma 18 45 mv 6.0 v v in 12 v, i out 0 a 0.4 0.8 quiescent current i b 6.0 v v in 12 v, i out 100 ma 1 5 ma v in 4.5v,i out 0 a 0.5 1.5 starting quiescent current i bstart v in 4.5 v, i out 100 ma 7 20 ma output noise voltage v no v in 7.0v, i out 40 ma, 10 hz f 100 khz 135 vrms ripple rejection r.r. 6.0 v v in 12 v, i out 40 ma, f 120 hz 50 64 db i out 40 ma 0.16 0.35 dropout voltage v d i out 100 ma 0.27 0.5 v average temperature coefficient of output voltage t cvo v in 7.0 v, i out 5 ma, 0c t j 125c 0.85 mv/c
ta48l018,02,025,03,033,05f 2003-01-15 6 electrical characteristics for all products generally, the characteristics of power supply ics change according to temperature fluctuations. the specification t j = 25 is based on a state where temperature increase has no effect (assuming no fluctuation in the characteristics) as ascertained by pulse tests. standard application circuit connect the input terminal and gnd, and the output terminal and gnd, by capacitor respectively. the capacitances should be determined experimentally. in particular, adequate investigation should be made so that there is no problem even at time of high or low temperature. 1 2 ta48lxxf 3 v out c out c in 0.33 f 3.3 f
ta48l018,02,025,03,033,05f 2003-01-15 7 p dmax ? ta v out ? t j v out ? v in i b ? v in v d ? i out v d ? t j ambient temperature ta (c) junction temperature t j (c) input voltage v in (v) input voltage v in (v) output current i out (ma) junction temperature t j (c) output voltage v out (v) allowable power dissipation p dmax (w) quiescent current i b (ma) output voltage v out (v) dropout voltage v d (v) dropout voltage v d (v) 3.0 50 ta48l033f v in 5.3 v i out 5 ma 3.2 3.4 3.6 0 50 100 150 ta48l033f 0 0 0.2 0.3 0.5 150 0.1 100 50 25c 125c 85c t j 40c 0.4 50 ta48l033f 0 50 0.2 0.3 0.5 150 0.1 100 0 40 ma 0.1 a i out 5 ma 0.4 i out 5 ma 0 0 2 3 4 4 6 10 1 40 ma 0.1 a 8 2 t j 25c i out 5 ma 0 0 2 3 5 46 10 1 4 40 ma 0.1 a 8 2 t j 25c 0 0 condition: number of ic 1 reflow soldering on a ceramic substrate single 0.4 0.8 1.2 1.6 2.4 2 40 80 120 160 40 40 0.8 mmt 20 30 0.8 mmt 15 15 0.8 mmt
ta48l018,02,025,03,033,05f 2003-01-15 8 t j 40c ta48l033f v in 5.3 v 0 0 2 3 4 150 1 100 50 25c 125c 85c i b ? t j i b ? i out v out ? i out i sc ? t j junction temperature t j (c) output current i out (ma) output current i out (ma) junction temperature t j (c) quiescent current i b (ma) quiescent current i b (ma) short circuit current i sc (ma) output voltage v out (v) i sc ? v d r.r. ? f dropout voltage v d (v) frequency f (khz) ripple rejection r.r. (db) short circuit current i sc (ma) i out 0.1 a 50 ta48l033f v in 5.3 v 0 50 2 3 4 150 1 100 0 40 ma 0 a 50 ta48l033f v in 5.3 v 0 50 200 300 400 150 100 100 0 6 ta48l033f t j 25c 0 0 200 300 400 15 100 9 3 12 200 ta48l033f v in 5.3 v t j 25c 0 0 2 3 4 400 1 300 100 1 ta48l033f v in 5.3 v i out 40 ma 0 0.01 40 60 80 100 20 10 0.1
ta48l018,02,025,03,033,05f 2003-01-15 9 package dimensions weight: 0.05 g (typ.)
ta48l018,02,025,03,033,05f 2003-01-15 10 toshiba is continually working to improve the quality and reliability of its products. nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. it is the responsibility of the buyer, when utilizing toshiba products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such toshiba products could cause loss of human life, bodily injury or damage to property. in developing your designs, please ensure that toshiba products are used within specified operating ranges as set forth in the most recent toshiba products specifications. also, please keep in mind the precautions and conditions set forth in the ?handling guide for semiconductor devices,? or ?toshiba semiconductor reliability handbook? etc.. the toshiba products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). these toshiba products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (?unintended usage?). unintended usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. unintended usage of toshiba products listed in this document shall be made at the customer?s own risk. the products described in this document are subject to the foreign exchange and foreign trade laws. the information contained herein is presented only as a guide for the applications of our products. no responsibility is assumed by toshiba corporation for any infringements of intellectual property or other rights of the third parties which may result from its use. no license is granted by implication or otherwise under any intellectual property or other rights of toshiba corporation or others. the information contained herein is subject to change without notice. 000707eb a restrictions on product use
|
