specification control drawing te connectivity 305 constitution drive menlo park, ca 94025, usa raychem products title: in-line splice sealing system, 1 to 1 mil-s-81824/1 unless otherwise specified dimensions are in millim eters. inches dimensions are between brackets. document no.: d-436-36/-37/-38 tolerances: 0.00 n/a 0.0 n/a 0 n/a angles: n/a roughness in micron te connectivity reserves the right to amend this drawing at any time. users should evaluate the suitability of the product for their application. date: 11may11 doc issue: 2 drawn by: m. foronda replaces: n/a dcr number: d000566 prod. rev. see table scale: none size: a sheet: 1 of 2 print date: 11-may-11 if this document is printed it becomes uncontrolled . check for the latest revision. product rev i.d.* product dimensions product name a (min) b (max) a b c d e max d-436-36 a 2.16 (0.085) 0.64 (0.025) 1.27 (0.050) 1.14 (0.045) 2.03 (0.080) 1.91 (0.075) 12.95 (0.510) 12.45 (0.490) 6.22 (0.245) 5.72 (0.225) 0.38 (0.015) d-436-37 a 2.79 (0.110) 0.64 (0.025) 1.75 (0.069) 1.63 (0.064) 2.69 (0.106) 2.57 (0.101) 14.86 (0.585) 14.35 (0.565) 7.11 (0.280) 6.60 (0.260) 0.51 (0.020) d-436-38 a 4.32 (0.170) 0.64 (0.025) 2.59 (0.102) 2.46 (0.097) 3.89 (0.153) 3.73 (0.147) 14.86 (0.585) 14.35 (0.565) 7.11 (0.280) 6.60 (0.260) 1.27 (0.050) * i.d.: a) as received; b) after unrestricted rec overy thru meltable insert.
specification control drawing te connectivity 305 constitution drive menlo park, ca 94025, usa raychem products title: in-line splice sealing system, 1 to 1 mil-s-81824/1 unless otherwise specified dimensions are in millim eters. inches dimensions are between brackets. document no.: d-436-36/-37/-38 tolerances: 0.00 n/a 0.0 n/a 0 n/a angles: n/a roughness in micron te connectivity reserves the right to amend this drawing at any time. users should evaluate the suitability of the product for their application. date: 11may11 doc issue: 2 drawn by: m. foronda replaces: n/a dcr number: d000566 prod. rev. see table scale: none size: a sheet: 2 of 2 print date: 11-may-11 if this document is printed it becomes uncontrolled . check for the latest revision. materials 1. insulation sleeve: heat-shrinkable, transparent blue, radiation cross-linked modified polyvinyliden e fluoride. 2. sealing rings: immersion resistant thermoplastic . color: one clear, one color coded (see table belo w). 3. crimp splicer: base metal: copper alloy 101 or 102 per astm b-75. plating: tin, per mil-t-10727, type i color code: see table below. product name mil spec equivalent wire range (awg) color code wgt. - lbs/mpc max d-436-36 m81824/-1-1 26 - 20 red 1.02 d-436-37 m81824/-1-2 20 - 16 blue 1.61 d-436-38 m81824/-1-3 16 - 12 yellow 2.720 application 1. these parts are designed to provide immersion re sistant in-line splices of 1 to 1 wires falling wit hin size range listed above, and having insulations rated for 135 c. 2. parts will meet all requirements of mil-s-81824/ 1 when installed as outlined below. assembly is not required for acceptance testing inspection. 3. acceptance sampling shall be in accordance with paragraph 4.6.1 of mil-s-81824. 4. packing and packaging shall be in accordance wit h sections 5, level c, of mil-s-81824. 5. this document takes precedence over documents re ference herein. assembly procedure: 1. slide sealing sleeve onto one of the wires to be sp liced. 2. strip wires 5/16 to 11/32. 3. insert one wire into barrel of crimp splicer and cr imp using a raychem ad-1377 crimp tool. repeat for other wire. 4. center sealing sleeve over the splice. 5. apply heat, using an approved heat source, first to one of the inserts and then the other. heat should be applied until insert melts and flows axially along the wire.
|
