[AKD4160-A] 2010/11 - 1 - general description the AKD4160-A is an evaluation board fo r the ak4160, which is 16-channel capacitive touch sensor with a low operating voltage and a low operating power. si nce the AKD4160-A has a i2c serial i/f, it is possible to control the ak4160 by writing and reading registers, and oper ate kinds of touch pad with a capacitor sensor connec tor on the AKD4160-A, ordering guide AKD4160-A --- evaluation board for ak4160 (cable for connecting with an usb port and c ontrol software is packed with this.) function ? i 2 c serial i/f ? cap sensor connector ? touch pad operations vdd port4 vss ak4160 optional port2 touch pad cs port1 control port i2c i/f irqnn figure 1. akd4160 block diagram * circuit diagram and pcb layout are attached at the end of this manual. evaluation board rev.0 for ak4160 a kd4160- a
[AKD4160-A] 2010/11 - 2 - board outline chart outline chart figure 2. AKD4160-A outline chart comment (1) vdd, vss, ifvdd, ifvss connect power supply with these pins. (2) sw1 the tactile switch for ak4160?s reset. (3) port1 control port. connect the bundled cable into this port. (4) port2 this port is for i/o of irq interrupt and input of reset pin. (5) port3 this port is for testing gpio functions of irq pins. (6) port4 this is a connector for the touch pad connection. connect the touch pad ?16 pad? or ?8pad+8led? into this port.
[AKD4160-A] 2010/11 - 3 - operation sequence (1) power supply lines. jumper pin setting. jp2 vdd (short) the power supply lines? connection. name color voltage comments vdd red 1.71 3.6v(typ=1.8v) power supply for vdd of ak4160. ifvdd orange typ=3.3v power supply for digital logic circuits. vss black 0v ak4160?s gnd. ifvss black 0v digital logic circuits? gnd. table 1. set up of power supply lines * each supply line should be distributed from the power supply unit. (2) set up the evaluation mode and jumper pins. (see the followings.)
[AKD4160-A] 2010/11 - 4 - evaluation mode when evaluating the functions of the ak4160, it is n ecessary to connect a touch pad board with the port4. regarding pin assignment of port4, refer to figure 4 or circuit diagrams in this manual. as for the ak4160?s register definitions, refer to the datasheet of the ak4160. (1) 16-channel touch switch capacitive touch sensors up to 16 channels are available for touch switch. connect the touch pad board ?16pad? with the port4. set up the registers of ak4160 with the ?AKD4160-A.exe? by loading the register file ?ak4160_16ch touch switch.akr? which is included in the cd. (refer to page 8) (2) 8-channel touch switch and 8-channel led display maximum 8 channels out of the 16-channel capacitive touch sensors can be configured to led drives. gpion (n=0 ? 7) outputs the status of terminal csn. (table 2) connect the touch pad board ?8pad+8led? with the port4. set up the registers of ak4160 with the ?AKD4160-A.exe? by loading the register file ?ak4160_8ch touch switch & 8ch led display.akr? which is included in the cd. (refer to page 8) no. csn status gpion output 1 cs0 gpio0 2 cs1 gpio1 3 cs2 gpio2 4 cs3 gpio3 5 cs4 gpio4 6 cs5 gpio5 7 cs6 gpio6 8 cs7 gpio7 table 2. the correspondence of gpion outputs and csn status
[AKD4160-A] 2010/11 - 5 - other jumper pins set up main board [jp1] (gnd): analog ground and digital ground open: separated. short: common. [jp4] (i/o): selection of u4 (74avc4t245)?s operation a-b: a data to b bus when irq / gpio is used as input. b-a: b data to a bus when irq / gpio is used as output. [jp5] (ad0): device address bit 0?s setting on i2c-bus mode open: ad0 bit is fixed to ?h?. short: ad0 bit is fixed to ?l?. [jp6] (ad1): device address bit 1?s setting on i2c-bus mode open: ad1 bit is fixed to ?h?. short: ad1 bit is fixed to ?l?. [jp7] (irq0n): interrupt i/o pin 0?s setting h: irq0n pin is pulled up. l: irq0n pin is pulled down. [jp8] (irq1n): interrupt i/o pin 1?s setting h: irq1n pin is pulled up. l: irq1n pin is pulled down. [jp9] (irq2n): interrupt i/o pin 2?s setting h: irq2n pin is pulled up. l: irq2n pin is pulled down. [jp10] (3.3v): power supply short open: when the voltage of ifvdd and vdd is different. short: when the voltage of ifvdd and vdd is the same. the function of the switch [sw1] (rstn): a push button switch for reset control of the ak4160. keep pushing sw1 if continuous reset is needed.
[AKD4160-A] 2010/11 - 6 - serial control the akd4160 can be connected with an usb port. connect port1 (control port) with a pc by the usb box packed with the akd4160. 6 4 # connect sda(ack) sda control port akd4160 scl port1 usb box 1 $ figure 3. connect of the usb box pin assignment of cap sensor connector vdd gpio0 gpio1 gpio2 gpio3 gpio4 gpio5 gpio6 gpio7 cs0 cs1 cs2 cs3 cs4 cs5 cs7 cs6 port4 cs figure 4. cap sensor connector pin assign ? descriptions of external circuits, appli cation circuits, software and other related information contained in this document are provided only to illustrate the operation and application examples of the semiconductor products. you are fully responsible for the incorporation of these external circuits, application circuits, software and other related info rmation in the design of your equipments. akm assumes no responsibility for any losses incurred by you or third parties arising from the use of this informat ion herein. akm assumes no liability for infringement of any patent, in tellectual property, or other rights in the application or u se of such information contained herein.
[AKD4160-A] 2010/11 - 7 - control software manual evaluation board and control soft settings 1. set an evaluation board properly. 2. connect port1 (control port) with a pc by the usb box packed with the akd4160. (please install the driver in the cd-rom when using this control software is used on windows 2000/xp/vista. please refer ?installation manual of control software driver by akm device control software?. in case of running on windows95/98/me, the driver install is not needed. in case of windows vista/7, open the property of the control soft, and set the compatibility to ?windows xp?. this contro l software does not operate on windows nt.) 3. continue to evaluation by following steps. operation screen 1. start up the control program, and the operation screen is shown below. figure 5. operation screen of control soft
[AKD4160-A] 2010/11 - 8 - operation overview register map and testing tool can be controlled by this control soft. these controls are selected by upper tabs. buttons which are frequently used such as register initializing button ?write default?, are located outside of the switching tab window. refer to the ? dialog boxes? for details of each dialog box setting. 1. [port reset]: for when connecti ng to usb i/f board (akdusbif-b) click this button after the control soft starts up when connecting usb i/f board (akdusbif-b). 2. [write default]: register initializing when the device is reset by a hardware reset, use this button to initialize the registers. 3. [all write]: executing write commands for all registers displayed. 4. [all read]: executing read comma nds for all registers displayed. 5. [save]: saving current register settings to a file. 6. [load]: executing data write from a saved file. 7. [all reg write]: ?all reg write? dialog box is popped up. 8. [data r/w]: ?data r/w? dialog box is popped up. 9. [sequence]: ?sequen ce? dialog box is popped up. 10. [sequence(file)]: ?sequence(file)? dialog box is popped up. 11. [read]: reading current register settings and display on to the register area (on the right of the main window). this is different from [all read] button, it does not reflect to a register map, only displaying hexadecimal.
[AKD4160-A] 2010/11 - 9 - tab functions 1. [reg]: register map this tab is for a register writing and reading. each bit on the register map is a push-button switch. button down indicates ?h? or ?1? and the bit name is in red (when read only it is in deep red). button up indicates ?l? or ?0? and the bit name is in blue (when read only it is in gray) grayout registers are read only registers. they can not be controlled. the registers which is not defined in the datasheet are indicated as ?---?. figure 6. register map example
[AKD4160-A] 2010/11 - 10 - [write]: data writing dialog it is for when changing two or more bits on the same address at the same time. click [write] button located on the right of th e each corresponded address for a pop-up dialog box. when checking the checkbox, the register will be ?h? or ?1?, when not checki ng the register will be ?l? or ?0?. click [ok] to write setting value to the registers, or click [cancel] to cancel this setting. figure 7. register wring dialog example [read]: data read click [read] button located on the right of the each corresponded address to execu te register reading. after register reading, the display will be updated regarding to th e register status. button down indicates ?h? or ?1? and the bit name is in red (when read only it is in deep red). button up indicates ?l? or ?0? and the bit name is in blue (when read only it is in gray) please be care that button statuses will be changed by read command.
[AKD4160-A] 2010/11 - 11 - 2. [tool]: testing tools this tab screen is for evaluation testing tool. click buttons for each testing tool. figure 8. repeat test & loop setting
[AKD4160-A] 2010/11 - 12 - dialog boxes 1. [all req write]: all req write dialog box click [all reg write] button in the main window to open register setting files. register setting files saved by [save] button can be applied. figure 9. [all reg write] window [open (left)]: selecting a register setting file (*.akr). [write]: executing register writing. [write all]: executing all register writings. writings are executed in descending order. [help]: help window is popped up. [save]: saving the register setting file a ssignment. the file name is ?*.mar?. [open (right)]: opening a saved register setting file assignment ?*. mar?. [close]: closing the dialog box and finish the process. *operating suggestions (1) those files saved by [save] button and opened by [o pen] button on the right of the dialog ?*.mar? should be stored in the same folder. (2) when register settings are changed by [save] button in the main window, re-read the file to reflect new register settings.
[AKD4160-A] 2010/11 - 13 - 2. [data r/w]: data r/w dialog box click the [data r/w] button in the main window for data read/write dialog box. data write is available to specified address. figure 10. [data r/w] window address box: input data address in hexadecimal numbers for data writing. data box: input data in hexadecimal numbers. mask box: input mask data in hexadecimal numbers. this is ?and? processed input data. [write]: writing to the address specified by ?address? box. [read]: reading from the address specified by ?address? box. the result will be shown in the read data box in hexadecimal numbers. [close]: closing the dialog box and finish the process. data writing can be cancelled by this button instead of [write] button. *the register map will be updated afte r executing [write] or [read] commands.
[AKD4160-A] 2010/11 - 14 - 3. [sequence]: sequence dialog box click [sequence] button to open register sequence setting dialog box. register sequence can be set in this dialog box. figure 11. [sequence] window sequence setting set register sequence by following process bellow. (1)select a command use [select] pull-down box to choose commands. corresponding boxes will be valid. < select pull-down menu > no_use: not using this address register: register writing reg(mask): register writing (masked) interval: taking an interval stop: pausing the sequence end: finishing the sequence (1) input sequence [address]: data address [data]: writing data [mask]: mask [data] box data is anded w ith [mask] box data. this is the actual writing data. when mask = 0x00, current setting is hold. when mask = 0xff, the 8bit data which is set in the [data] box is written. when mask =0x0f, lower 4bit da ta which is set in the [data] box is written. upper 4bit is hold to current setting.
[AKD4160-A] 2010/11 - 15 - [ interval ]: interval time valid boxes for each process command are shown bellow. no_use: none register: [address], [data], [interval] reg(mask): [address], [data], [mask], [interval] interval: [interval] stop: none end: none control buttons the function of control button is shown bellow. [start]: executing the sequence [help]: opening a help window [save]: saving sequence settings as a file. the file name is ?*.aks?. [open]: opening a sequence setting file ?*.aks?. [close]: closing the dialog box and finish the process. stop of the sequence when ?stop? is selected in the sequence, processing is pa used and it starts again when [start] button is clicked. restarting step number is shown in the ?start step? box. when finishing the pr ocess until the end of sequence, ?start step? will return to ?1?. the sequence can be started from any step by writing the step number to the ?start step? box. write ?1? to the ?start step? box and click [start] button, when restarting the process from the beginning.
[AKD4160-A] 2010/11 - 16 - 4. [sequence(file)]: sequence setting file dialog box click [sequence(file)] button to open sequence setting file dialog box. those files saved in the ?sequence setting dialog? can be applied in this dialog. figure 12. [sequence(file)] window [open (left)]: opening a sequence setting file (*.aks). [start]: executing the sequence setting. [start all]: executing all sequence settings. sequences are executed in descending order. [help]: pop up the help window. [save]: saving sequence setting file assi gnment. the file name is ?*.mas?. [open(right)]: opening a saved sequence setting file assignment ?*. mas?. [close]: closing the dialog box and finish the process. *operating suggestions (1) those files saved by [save] button and opened by [o pen] button on the right of the dialog ?*.mas? should be stored in the same folder. (2) when ?stop? is selected in the sequence the process will be paused and a pop-up message will appear. click ?ok? to continue the process.
[AKD4160-A] 2010/11 - 17 - revision history date (yy/mm/dd) manual revision board revision reason page contents 10/11/05 km104500 0 fi rst edition 10/11/26 km104501 0 6 figure.4 add 10/11/26 km104501 0 8 figure.6 change 10/11/26 km104501 0 12 figure.8 change important notice z these products and their specifications are subject to change without notice. when you consider any use or application of these produc ts, please make inquiries the sales office of asahi kasei microdevices corporation (akm) or authorized distributors as to current status of the products. z descriptions of external circuits, application circuits, software and other related information contained in this document are provided only to illustrate the operation and application exampl es of the semiconductor products. you are fully responsible for the incorporation of these external circuits, application circuits, software and other related information in the design of your e quipments. akm assumes no responsibility fo r any losses incurred by you or third parties arising from the use of these information herein. akm assumes no liability for infringement of any patent, intellectual property, or other rights in the applica tion or use of such information contained herein. z any export of these products, or devices or systems containi ng them, may require an export license or other official approval under the law and regulations of the country of e xport pertaining to customs and tariffs, currency exchange, or strategic materials. z akm products are neither intended nor aut horized for use as critical components note1 ) in any safety, life support, or other hazard related device or system note2 ) , and akm assumes no responsibility fo r such use, except for the use approved with the express written consent by representative director of akm. as used here: note1 ) a critical component is one whose failure to functi on or perform may reasonably be expected to result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it, and which must therefore meet very high standards of performance and reliability. note2 ) a hazard related device or system is one designed or intended for life support or maintenance of safety or for applications in medicine, aeros pace, nuclear energy, or other fields, in which its failure to function or perform may reasonably be expected to result in loss of life or in significant injury or damage to person or property. z it is the responsibility of the buyer or distributor of akm products , who distributes, disposes of, or otherwise places the product with a third party, to notify such third party in advance of the above conten t and conditions, and the buyer or distributor agrees to assume any and all responsib ility and liability for and hold akm harmless from any and all claims arising from the use of said product in the absence of such notification.
5 5 4 4 3 3 2 2 1 1 d d c c b b a a vdd vdd ifvdd gpio0 gpio1 gpio2 gpio4 gpio3 gpio5 gpio6 gpio7 cs7 cs0 cs1 cs2 cs3 cs4 cs5 cs6 ad0 scl ad1 sda vdd gpio0 gpio1 gpio2 gpio3 gpio4 gpio5 gpio6 gpio7 cs0 cs1 cs2 cs3 cs4 cs5 cs7 cs6 ifvdd ifvdd ifvdd scl sda irq0n vdd irq0n irq1n irq2n irq1n irq2n vdd ifvdd vdd ad0 vdd ad1 rstn irq2n irq1n irq0n ifvdd irq0n irq1n irq2n ifvdd rstn title size document number rev date: sheet of 0 a3 11 thursday, september 30, 2010 title size document number rev date: sheet of <doc> 0 <title> a3 11 thursday, september 30, 2010 title size document number rev date: sheet of <doc> 0 <title> a3 11 thursday, september 30, 2010 gpio5 gpio4 gpio3 gpio2 gpio1 gpio0 gpio6 gpio7 cs0 cs1 cs2 cs3 cs4 cs5 cs6 cs7 irq0n irq1n irq2n ad0 scl ad1 sda scl sda(ack) sda irq0n irq2n irq1n vdd vss vreg rstn rstn <a href='http://www.datasheet.hk/search.php?part=akd4160-a&stype=part'>AKD4160-A</a> main a-b b-a rref h h h l l l r10 51 r10 51 c3 0.047u c3 0.047u jp1 gnd jp1 gnd port2 optional port2 optional 1 3 5 7 9 10 8 6 4 2 test17 test17 test12 test12 test1 test1 + c5 47u + c5 47u r22 100k r22 100k r4 1k r4 1k cn4 7pin_1 cn4 7pin_1 1 2 3 4 5 6 7 r26 10k r26 10k r21 100k r21 100k test9 test9 test20 test20 r5 10k r5 10k u1 ak4160 u1 ak4160 irq0n/gpioa 1 irq1n/gpiob 2 irq2n/gpioc 3 ad0 4 scl 5 ad1 6 sda 7 rstn 8 vreg 9 vss 10 rref 11 cs0 12 cs1 13 cs2 14 cs9/gpio6 21 cs8/gpio7 20 cs7 19 cs6 18 cs5 17 cs4 16 cs3 15 vdd 28 cs15/gpio0 27 cs14/gpio1 26 cs13/gpio2 25 cs12/gpio3 24 cs11/gpio4 23 cs10/gpio5 22 r9 51 r9 51 jp4 i/o jp4 i/o test26 test26 c9 0.1u c9 0.1u test24 test24 r12 1k r12 1k r7 470 r7 470 test15 test15 test16 test16 test27 test27 r19 51 r19 51 r23 100k r23 100k test13 test13 test7 test7 c8 0.1u c8 0.1u jp7 irq0n jp7 irq0n cn2 7pin_1 cn2 7pin_1 1 2 3 4 5 6 7 r18 51 r18 51 sw1 rstn sw1 rstn 1 2 test10 test10 test19 test19 test6 test6 r17 51 r17 51 test23 test23 r25 100k r25 100k r6 10k r6 10k jp10 3.3v jp10 3.3v r28 100k r28 100k r27 100k r27 100k + c2 1u + c2 1u test22 test22 jp6 ad1 jp6 ad1 r11 51 r11 51 c7 0.1u c7 0.1u jp9 irq2n jp9 irq2n c11 0.1u c11 0.1u r14 100 r14 100 port1 ctrl port1 ctrl 1 3 5 7 9 10 8 6 4 2 r24 100k r24 100k test5 test5 test28 test28 test2 test2 c10 0.1u c10 0.1u test14 test14 r16 100 r16 100 port3 irq port3 irq u4 74avc4t245 u4 74avc4t245 1a1 4 1a2 5 2a2 7 1oe 15 1b1 13 1b2 12 2b1 11 2b2 10 gnd 9 2a1 6 1dir 2 vccb 16 vcca 1 gnd 8 2dir 3 2oe 14 r8 470 r8 470 r13 100 r13 100 cn3 7pin_1 cn3 7pin_1 1 2 3 4 5 6 7 test4 test4 c4 0.01u c4 0.01u u3 74lvc07 u3 74lvc07 1a 1 2a 3 3a 5 4a 9 5a 11 6a 13 vcc 14 gnd 7 1y 2 2y 4 3y 6 4y 8 5y 10 6y 12 test18 test18 test11 test11 test25 test25 r15 100 r15 100 jp2 vdd jp2 vdd test3 test3 port4 cs port4 cs test8 test8 cn1 7pin_1 cn1 7pin_1 1 2 3 4 5 6 7 u2 74avc4t245 u2 74avc4t245 1a1 4 1a2 5 2a2 7 1oe 15 1b1 13 1b2 12 2b1 11 2b2 10 gnd 9 2a1 6 1dir 2 vccb 16 vcca 1 gnd 8 2dir 3 2oe 14 r3 100k r3 100k test21 test21 c1 0.01u c1 0.01u jp5 ad0 jp5 ad0 jp8 irq1n jp8 irq1n + c6 47u + c6 47u r20 51 r20 51
<br> 5 5 4 4 3 3 2 2 1 1 d d c c b b a a vdd gpio0 gpio1 gpio2 gpio3 gpio4 gpio5 gpio6 gpio7 cs0 cs1 cs2 cs3 cs4 cs5 cs7 cs6 cs3 cs2 cs1 cs0 cs7 cs6 cs5 cs4 gpio4 gpio5 gpio6 gpio7 gpio0 gpio1 gpio2 gpio3 title size document number rev date: sheet of <doc> 0 <title> a4 11 wednesday, september 08, 2010 title size document number rev date: sheet of <doc> 0 <title> a4 11 wednesday, september 08, 2010 title size document number rev date: sheet of <doc> 0 <title> a4 11 wednesday, september 08, 2010 <a href='http://www.datasheet.hk/search.php?part=akd4160-a&stype=part'>AKD4160-A</a>-touch pad 16 pad 13 13 1 1 8 8 2 2 15 15 3 3 12 12 4 4 9 9 10 10 11 11 5 5 14 14 6 6 7 7 port5 cs_pad1 port5 cs_pad1 0 0
<br> 5 5 4 4 3 3 2 2 1 1 d d c c b b a a vdd gpio0 gpio1 gpio2 gpio3 gpio4 gpio5 gpio6 gpio7 cs0 cs1 cs2 cs3 cs4 cs5 cs7 cs6 cs3 cs2 cs1 cs0 cs7 cs6 cs5 cs4 gpio0 gpio1 gpio2 gpio3 gpio4 gpio5 gpio6 gpio7 title size document number rev date: sheet of <doc> 0 <title> a4 11 wednesday, september 08, 2010 title size document number rev date: sheet of <doc> 0 <title> a4 11 wednesday, september 08, 2010 title size document number rev date: sheet of <doc> 0 <title> a4 11 wednesday, september 08, 2010 <a href='http://www.datasheet.hk/search.php?part=akd4160-a&stype=part'>AKD4160-A</a>-touch pad 8pad & 8led tp2 tp2 cs2 cs2 cs4 cs4 led0 led0 2 1 led1 led1 2 1 tp5 tp5 cs1 cs1 led2 led2 2 1 tp3 tp3 tp1 tp1 led3 led3 2 1 vr2 1k vr2 1k cs0 cs0 led4 led4 2 1 vr7 1k vr7 1k vr5 1k vr5 1k led5 led5 2 1 led6 led6 2 1 tp6 tp6 tp4 tp4 cs7 cs7 led7 led7 2 1 tp7 tp7 vr4 1k vr4 1k vr3 1k vr3 1k vr1 1k vr1 1k cs6 cs6 vr0 1k vr0 1k vr6 1k vr6 1k port6 cs_pad2 port6 cs_pad2 cs3 cs3 tp0 tp0 cs5 cs5
<br>
<br>
<br>
<br>
<br>
<br>
<br>
<br>
<br>
<br>
<br>
<br>
<br>
<br>
<br>
<br>
<br>
<br></td>
</tr>
</table>
<table border="0" width="980" id="table32" style="font-size:1px" height="10">
<tr>
<td></td>
</tr>
</table>
<table border="0" width="980" id="table31" style="font-size:1px" height="40">
<tr>
<td background="images/bg03.gif">
<p align="right"><br>
<font color="#FF0000"><a href="#top">▲Up To
Search▲</a> </font></td>
</tr>
</table>
<table border="0" width="980" id="table27">
<tr>
<td> </td>
</tr>
<tr>
<td>
<b><font size="5">Price & Availability of AKD4160-A </font></b>
<a target="_blank" href="https://www.findchips.com/search/AKD4160-A"><img border="0" src="images/fc_logo.jpg" width="265" height="25"></a></td>
</tr>
<tr>
<td><script src="http://www.findchips.com/api/inventory/search/AKD4160-A?limit=5&partner=18"></script>
<script>document.getElementById("poweredBy").style.visibility="hidden";</script></td>
</tr>
</table>
</div>
<div align="center">
<table border="0" width="980" id="table13" style="font-size:12px">
<tr>
<td>
<table border="0" width="980" id="table26" style="font-size:1px">
<tr>
<td background="images/bg03.gif"></td>
</tr>
</table>
</td>
</tr>
<tr>
<td>
<p align="right">All Rights Reserved © <span lang="zh-cn">
IC-ON-LINE 2003 - 2022</span> </td>
</tr>
</table>
</div>
<div align="center">
<table border="0" width="980" id="table13" style="font-size:12px">
<tr>
<td>[<a href="javascript:addbookmark()">Add Bookmark</a>] [<a href="mailto:ioldatasheet@gmail.com" target="_blank">Contact
Us</a>] [<a href="link.php">Link exchange</a>] [<a href="privacy.php">Privacy policy</a>]</td>
</tr>
<tr>
<td>
Mirror Sites : [<a href="http://www.datasheet.hk">www.datasheet.hk</a>]
[<a href="http://www.maxim4u.com">www.maxim4u.com</a>] [<a href="http://www.ic-on-line.cn">www.ic-on-line.cn</a>]
[<a href="http://www.ic-on-line.com">www.ic-on-line.com</a>] [<a href="http://www.ic-on-line.net">www.ic-on-line.net</a>]
[<a href="http://www.alldatasheet.com.cn">www.alldatasheet.com.cn</a>]
[<a href="http://www.gdcy.com">www.gdcy.com</a>]
[<a href="http://www.gdcy.net">www.gdcy.net</a>]<br><br><br></td>
</tr>
</table>
</div>
<style type="text/css">
.style1 {
background-color: #333333;
}
.style2 {
color: #FFFFFF;
}
.style3 {
color: #0000FF;
}
.style4 {
color: #FFFFFF;
font-size: large;
}
.style5 {
text-decoration: none;
}
.style6 {
color: #6EF3F2;
}
.style7 {
border-width: 0px;
}
</style>
<a href="http://www.maxim4u.com/che_s1.php" rel="nofollow">.</a>
<a href="http://www.maxim4u.com/che_s2.php" rel="nofollow">.</a>
<a href="http://www.maxim4u.com/che_s3.php" rel="nofollow">.</a>
<a href="http://www.maxim4u.com/che_s4.php" rel="nofollow">.</a>
<a href="http://www.maxim4u.com/che_s5.php" rel="nofollow">.</a>
<br>
<div style="position:fixed ;bottom:0px;width:100%" id="id_cookies">
<table height="33" align="center" class="style1" style="width: 100%">
<tr>
<td align="left" class="style2" style="width: 23px"> </td>
<td align="left" class="style2">We use cookies to deliver the best possible
web experience and assist with our advertising efforts. By continuing to use
this site, you consent to the use of cookies. For more information on
cookies, please take a look at our <a href="privacy.php">
<span class="style6">Privacy Policy</span></a>.</td>
<td align="center" class="style3" style="width: 100px">
<a href="javascript:iscookies()" class="style5"><span class="style4">X</span></a></td>
</tr>
</table></div>
<script type="text/javascript" src="js/jquery.min.js"></script>
<script type="text/javascript" src="js/cookie.js"></script>
<script type="text/javascript">
$(function (){
if($.cookie("OkCookies") == 'OK')
{
document.getElementById('id_cookies').style.display="none";
}
});
function iscookies(){
document.getElementById('id_cookies').style.display="none";
$.cookie("OkCookies",'OK',{ expires:3});
}
</script>
<script>
(function(){
var bp = document.createElement('script');
var curProtocol = window.location.protocol.split(':')[0];
if (curProtocol === 'https') {
bp.src = 'https://zz.bdstatic.com/linksubmit/push.js';
}
else {
bp.src = 'http://push.zhanzhang.baidu.com/push.js';
}
var s = document.getElementsByTagName("script")[0];
s.parentNode.insertBefore(bp, s);
})();
</script>
<script type="text/javascript">
var _gaq = _gaq || [];
_gaq.push(['_setAccount', 'UA-280427-2']);
_gaq.push(['_trackPageview']);
(function() {
var ga = document.createElement('script'); ga.type = 'text/javascript'; ga.async = true;
ga.src = ('https:' == document.location.protocol ? 'https://ssl' : 'http://www') + '.google-analytics.com/ga.js';
var s = document.getElementsByTagName('script')[0]; s.parentNode.insertBefore(ga, s);
})();
</script>
<script src="http://www.google-analytics.com/urchin.js" type="text/javascript">
</script>
<script type="text/javascript">
_uacct = "UA-280427-1";
urchinTracker();
</script>
<script>
var _hmt = _hmt || [];
(function() {
var hm = document.createElement("script");
hm.src = "//hm.baidu.com/hm.js?db7b417c2a40fa0c35a5e98cab960d1b";
var s = document.getElementsByTagName("script")[0];
s.parentNode.insertBefore(hm, s);
})();
</script>
</body>
</html>
|
