34 ? nic components corp. www .niccomp. com www .lowesr. com www .rfpassives. com www .smtmagnetics. com nspe-t series hybrid aluminum electrolytic capacitors rated voltage range 25 ~ 100vdc rated capacitance range 3.9 ~ 270 f operating temp. range -55 ~ +125c capacitance tolerance 20% (m) max. leakage current after 2 minutes @ 20c less than 0.05cv or 100 a whichever is greater working and surge voltage ratings w.v. (vdc) 25 35 50 63 80 100 s.v. (vdc) 32 44 63 79 100 125 tan @ 120hz/20c 0.16 impedance ratio z -55c/z +20c 1 ~ 2.5 z +125c/z +20c 0.6 ~ 1.0 load life test @ 125c and rated voltage w.v. (vdc) 25 35 50 63 80 100 case dia. 6.3mm 2000 hrs. 8 & 10mm 3000 hrs. capacitance change within 30% of initial measured value tan and esr less than 200% of speci? ed max. value leakage current less than speci? ed max. value esr less than 200% of speci? ed max. value resistance to soldering heat hot plate at +250c for 30 seconds with electrodes facing downward capacitance change within 10% of the initial measured value dissipation factor less than the initial limit leakage current less then the initial limit characteristics ? cylindrical v-chip construction for surface mounting ? extended load life at high temperture (2,000 ~ 3,000 hours @ +125c) ? high voltage ratings (25 ~ 100vdc) ? low esr and high ripple current ratings ? 6.3x8mm ~ 10x10.8mm case sizes ? reflow soldering rated to +260c (+250c 80v & 100v) expanded 80v & 100v values part number cap. ( f) working voltage case size (d x l) mm max. tan 120hz/20c max. esr (m ) at 100khz/20c max. ripple current (ma rms) at 100khz/125c load life hours (+125c) nspe-t680m25v6.3x8nbyf 68 25 6.3x8 0.16 45 980 2000 nspe-t151m25v8x10.8nbyf 150 8x10.8 0.16 27 1330 3000 nspe-t271m25v10x10.8nbyf 270 10x10.8 0.16 22 1520 3000 nspe-t470m35v6.3x8nbyf 47 35 6.3x8 0.16 60 910 2000 nspe-t101m35v8x10.8nbyf 100 8x10.8 0.16 30 1260 3000 nspe-t151m35v10x10.8nbyf 150 10x10.8 0.16 23 1480 3000 nspe-t100m50v6.3x8nbyf 10 50 6.3x8 0.16 80 840 2000 nspe-t330m50v8x10.8nbyf 33 8x10.8 0.16 35 1170 3000 nspe-t560m50v10x10.8nbyf 56 10x10.8 0.16 25 1390 3000 nspe-t3r9m63v6.3x8nbyf 3.9 63 6.3x8 0.16 100 740 2000 nspe-t220m63v8x10.8nbyf 22 8x10.8 0.16 40 1090 3000 nspe-t330m63v10x10.8nbyf 33 10x10.8 0.16 30 1260 3000 nspe-t120m80v10x10.8lbyf 12 80 10x10.8 0.16 70 900 3000 nspe-t100m100v10x10.8lbyf 10 100 10x10.8 0.16 80 870 3000 standard products and case sizes d x l (mm) new values
35 ? nic components corp. www .niccomp. com www .lowesr. com www .rfpassives. com ww w.smtmagnetics. com part marking capacitance value voltage lot code series code 3r9 63v t__ dimensions (mm) 0.3mm max. d l case size d 0.5 l max. a, b 0.2 w i 0.2 p 0.2 6.3x8 6.3 8.0 6.6 0.5 ~ 0.8 2.5 2.2 8x10.8 8.0 10.8 8.3 0.7 ~ 1.0 2.9 3.2 10x10.8 10 10.8 10.3 1.0 ~ 1.4 3.2 4.6 + - i i w p a b nspe-t series hybrid aluminum electrolytic capacitors land pattern dim. (mm) + - aa p b case dia. a b p 6.3 3.5 1.8 2.1 8 4.1 2.1 2.8 10 4.4 2.5 4.3 diameter time above +200c time above +217c time above +230c peak temperature 6.3 ~ 63v 100 sec. max. 80 sec. max. 40 sec. max. +260c (5 sec. max.) 80 ~ 100v +250c (5 sec. max.) peak temperature and duration recommended reflow soldering profile* time above 200c (80 seconds max.) 50 100 150 200 time (seconds) temperature - deg. c preheat - 120 seconds max. (+150c ~ +190c) peak temperature (260c/5 seconds) 260 230 time above 230c (40 seconds max.) *two re? ow passes are permissible with a cool down to room temperature required between the ? rst and second pass. nspe-t 220 m 63v 8x10.8 n b y f rohs compliant sn-bi finish, 13" reel re? ow temp. code (n=+260c) size in mm working voltage tolerance code m=20% capacitance code in f, ? rst 2 digits are signi? cant third digit is no. of zeros, ?r? indicates decimal for values under 10 f series part number system suitable for automotive equipment, sourced to special production and inspection at ts-16949 certi? ed production site
36 ? nic components corp. www .niccomp. com www .lowesr. com www .rfpassives. com www .smtmagnetics. com nspe-t series hybrid aluminum electrolytic capacitors t a p feeding + - 1.5 ? +0.1/- 1.75 d b c 1.5 +0.1/-0 1.75 + 0.15 t 4 + 0.1 case size a 0.5 b 0.5 c 0.3 d 0.1 p 0.1 t 0.2 t max. 6.3x8 7.0 7.0 16.0 7.5 12.0 8.2 0.6 8x10.8 8.7 8.7 24.0 11.5 16.0 11.0 0.6 10x10.8 10.7 10.7 24.0 11.5 16.0 11.0 0.6 case size w 1.0 qty per reel 13" (330mm) 6.3x8 18 500 8x10.5 26 300 10x10.5 26 300 reel dimensions (mm) taping specifications (mm) 1. both leader and trailer tape: minimum 40mm (1.57") empty carrier tape pockets. 2. leader tape: approximately 20cm of cover tape at leader. 3. connection: maximum 3 connections (slices) per reel. 2mm 0.5mm 13mm 0.5mm 21mm 0.8mm 330mm 2.0mm or 380mm 2.0mm 50mm min. w 3mm precautions please review the notes on correct use, safety and precautions found on pages t10 & t11 of nic?s electrolytic capacitor catalog . also found at www.niccomp.com/precautions if in doubt or uncertainty, please review your speci c application - process details with nic?s technical support personnel: tpmg@niccomp.com
|