e l e c t r o n i c s i n c . 14 pin dip 5 tap low profile ttl compatible active delay lines tel: (818) 892-0761 fax: (818) 894-5791 http://www.pca.com pca electronics, inc. 16799 schoenborn st. north hills, ca 91343 epa073hl-xx & epa073hl-xx-rc product performance is limited to specified parameters. data is subject to change without prior notice. unless otherwise specified dimensions are in inches /mm ?.010 /.25 csa073-hl & -rc rev. - 11/14/05 rr schematic package add ?rc?after part number for rohs compliant tap delays ( ? ?% or ?2ns) 5, 10, 15, 20 6, 12, 18, 24 7, 14, 21, 28 8, 16, 24, 32 9, 18, 27, 36 10, 20, 30, 40 12, 24, 36, 48 15, 30, 45, 60 20, 40, 60, 80 25, 50, 75, 100 30, 60, 90, 120 35, 70, 105, 140 total delay ( ? ?% or ?2ns) 25 30 35 40 45 50 60 75 100 125 150 175 pca part number epa073hl-200(-rc) epa073hl-225(-rc) epa073hl-250(-rc) epa073hl-300(-rc) epa073hl-350(-rc) epa073hl-400(-rc) epa073hl-420(-rc) epa073hl-440(-rc) epa073hl-450(-rc) epa073hl-470(-rc) epa073hl-500(-rc) tap delays ( ? ?% or ?2ns) 40, 80, 120, 160 45, 90, 135, 180 50, 100, 150, 200 60, 120, 180, 240 70, 140, 210, 280 80, 160, 240, 320 84, 168, 252, 336 88, 176, 264, 352 90, 180, 270, 360 94, 188, 282, 376 100, 200, 300, 400 total delay ( ? ?% or ?2ns) 200 225 250 300 350 400 420 440 450 470 500 pca part number epa073hl-25(-rc) epa073hl-30(-rc) epa073hl-35(-rc) epa073hl-40(-rc) epa073hl-45(-rc) epa073hl-50(-rc) epa073hl-60(-rc) epa073hl-75(-rc) epa073hl-100(-rc) epa073hl-125(-rc) epa073hl-150(-rc) epa073hl-175(-rc) ? whichever is greater. delay times referenced from input to leading and trailing edges at 25?, 5.0v, with no load. recommended operating conditions v cc supply voltage v ih high-level input voltage v il low-level input voltage i ik input clamp current i oh high-level output current i ol low-level output current p w * pulse width of total delay d* duty cycle t a operating free-air temperature min. 4.75 2.0 40 0 max. 5.25 0.8 -18 -1.0 20 40 +70 unit v v v ma ma ma % % ? *these two values are inter-dependent. input pulse test conditions @ 25?c e in pulse input voltage p w pulse width % of total delay t ri pulse rise time (0.75 - 2.4 volts) p rr pulse repetition rate @ td 200 ns pulse repetition rate @ td > 200 ns v cc supply voltage 3.2 110 2.0 1.0 100 5.0 unit volts % ns mhz khz volts dc electrical characteristics parameter test conditions v oh high-level output voltage v cc = min. v il = max. i oh = max v ol low-level output voltage v cc = min. v ih = min. i ol = max v ik input clamp voltage v cc = min. i i = ii k i ih high-level input current v cc = max. v in = 2.7v v cc = max. v in = 5.25v i il low-level input current v cc = max. v in = 0.5v i os short circuit output current v cc = max. v out = 0. min. 2.7 -40 (one output at a time) i cch high-level supply current v cc = max. v in = open i ccl low-level supply current v cc = max. v in = 0 t ro output rise time td 500 ns (0.75 to 2.4 volts) td > 500 ns max. 0.5 -1.2 50 1.0 -2 -100 75 75 4 5 n h fanout high-level output v cc = max. v oh = 2.7v 20 ttl load n l fanout low-level output v cc = max. v ol = 0.5v 10 ttl load unit v v v ? ma ma ma ns ns ma ma 12 4 10 6 8 1 7 output ground input 14 vcc .100 (2.54) pca epa073hl-xx(-rc) date code .280 max. (7.11) .780 max. (19.81) .165 max. (4.19) .010 typ. (.254) .050 (1.27) .410 (10.41) .055 (1.40) .300 (7.62) .030 (.762) suggested solder pad layout .300 (7.62) .200 (5.08) .300 (7.62) .200 (5.08) .400 max. (10.16) notes : 2. peak solder rating (per ipc/jedec-j-std-020c) 4. weight 3. moisture sensitive levels (msl) (per ipc/jedec-j-std-020c) 1. assembly process (solder composition) (leadframe) (assembly solder) 5. packaging information (*add ?r?to end of part number when placing order) (tube) (tape & reel) epa073hl-xx-rc 260? 1.35 grams 4 (72 hours, 30?/60%rh) snpb (rohs exemption 7a) sn 27 pieces/tube 600 pieces/13?reel (*epa073hl-xx-rctr) epa073hl-xx 225? 1.35 grams 3 (168 hourss, 30?/60%rh) snpb snpb 27 pieces/tube 600 pieces/13?reel (*epa073hl-xx-tr)
|
