15,000 w surface mount transient voltage suppressor microsemi scottsdale division page 1 copyright ? 2007 10-12-2007 rev g www. micr o semi . com scottsdale division plad15kp5.0 thru plad15kp400ca, e3 plad15kp5.0- 400ca, e3 description appearance these microsemi 15 kw transient voltage suppressors (tvss) are designed for applications requiring protection of voltage- sensitive electronic devices that may be damaged by harsh or severe voltage transients including lightning per iec61000-4-5 and classes with various source impedances described herein. this series is available in 5.0 to 400 volt standoff voltages (v wm ) in both unidirectional and bidirectional offered in one surface mount device. microsemi also offers numerous other tvs products to meet higher and lower power demands and special applications. important: for the most current data, consult microsemi?s website: http://www.microsemi.com features applications / benefits ? available in both unidirectional and bidirectional construction (bidirectional with c or ca suffix) ? low profile surface mount ? available in tape-and-reel or waffle pack ? selections for 5.0 to 400 volts standoff voltages (v wm ) ? suppresses transients up to 15,000 watts @ 10/1000 s (see figure 1) ? fast response ? optional 100% screening for avionics grade is available by adding ma prefix to part number for added 100% temperature cycle -55 o c to +125 o c (10x) as well as surge (3x) and 24 hours htrb with post test v z & i r (in the operating direction for unidirectional or both directions for bidirectional) ? options for screening in accordance with mil-prf- 19500 for jan, jantx, and jantxv are also available by adding mq, mx, or mv prefixes respectively to part numbers. ? moisture classification is level 1 with no dry pack required per ipc/jedec j-std-020b ? rohs compliant devices available by adding ?e3? suffix ? protection from switching transients and induced rf ? protection from esd, and eft per iec 61000-4-2 and iec 61000-4-4 ? secondary lightning protection per iec61000-4-5 with 42 ohms source impedance: class 1,2,3,4: plad15kp5.0a to 400a or ca class 5: plad15kp5.0a to 400a or ca ? secondary lightning protection per iec61000-4-5 with 12 ohms source impedance: class 1,2,3,4: plad15kp5.0a to 400a or ca ? secondary lightning protection per iec61000-4-5 with 2 ohms source impedance: class 2,3: plad15kp5.0a to 400a or ca class 4: plad15kp5.0 to 54a or ca ? pin injection protection per rtca/do-160d for waveform 4 (6.4/69 s): level 4: plad15kp5.0a to 400a or ca level 5: plad15kp5.0a to 100a or ca ? pin injection protection per rtca/do-160d for waveform 5a (40/120 s): level 4: plad15kp5.0a to 28a or ca maximum ratings mechanical and packaging ? operating and storage temperature: -55 o c to +150 o c ? peak pulse power dissipation at 25 o c: 15,000 watts at 10/1000 s (also see figures 1 and 2) ? impulse repetition rate (duty factor): 0.05% ? t clamping (0 volts to v (br) min.): < 100 ps theoretical for unidirectional and < 5 ns for bidirectional ? thermal resistance: 0.2 c/w junction to case or 50 o c/w junction to ambient when mounted on fr4 pc board with recommended mounting pad (see last page) ? steady-state power dissipation: 50 watts at t c = 100 o c with good heat sink, or 2.5 watts at t a = 25 o c if mounted on fr4 pc board as described for thermal resistance ? forward surge voltage: 3.5 v maximum @ 500 amps 8.3 ms half-sine wave (unidi rectional devices only) ? solder temperatures: 260 o c for 10 s (maximum) ? case: void-free transfer molded thermosetting epoxy body meeting ul94v-0 ? terminals: tin-lead or rohs compliant annealed matte-tin plating readily solderable per mil-std-750, method 2026 ? marking: body marked with part number ? polarity: for unidirect ional devices, the cathode is on the metal backside (package bottom) ? weight: 1 gram (approximate) ? tape & reel: standard per eia-481-b (add ?tr? suffix to part number) ? see package dimensions on last page 8700 e. thomas rd. po box 1390, scottsdale, az 85252 usa, (480) 941-6300, fax: (480) 947-1503
15,000 w surface mount transient voltage suppressor microsemi scottsdale division page 2 copyright ? 2007 10-12-2007 rev g www. micr o semi . com scottsdale division plad15kp5.0 thru plad15kp400ca, e3 plad15kp5.0- 400ca, e3 electrical characteristics microsemi part number (note 2) reverse stand-off voltage v wm (note 1) volts breakdown voltage v (br) v (br) @ i (br) volts ma maximum clamping voltage v c @ i pp volts maximum standby current i d @ v wm a maximum peak pulse current i pp (fig. 3) a maximum temperature coefficient of v (br) v(br ) mv/ oc plad15kp5.0 plad15kp5.0a plad15kp6.0 plad15kp6.0a 5.0 5.0 6.0 6.0 6.40 ? 7.30 6.40 ? 7.00 6.67 ? 8.15 6.67 ? 7.37 150 150 150 150 9.6 9.2 11.4 10.3 15000 15000 15000 15000 1620 1629 1317 1455 4.0 4.0 4.0 4.0 plad15kp6.5 plad15kp6.5a plad15kp7.0 plad15kp7.0a 6.5 6.5 7.0 7.0 7.22 ? 8.82 7.22 ? 7.98 7.78 ? 9.51 7.78 ? 8.60 150 150 150 150 12.3 11.2 13.3 12.0 6000 6000 3000 3000 1221 1341 1134 1251 4.0 4.0 5.0 5.0 plad15kp7.5 plad15kp7.5a plad15kp8.0 plad15kp8.0a 7.5 7.5 8.0 8.0 8.33 ? 10.2 8.33 ? 9.21 8.89 ? 10.9 8.89 ? 9.83 5 5 5 5 14.3 12.9 15.0 13.6 750 750 450 450 1350 1164 999 1101 6.0 6.0 6.0 6.0 plad15kp8.5 plad15kp8.5a plad15kp9.0 plad15kp9.0a 8.5 8.5 9.0 9.0 9.44 ? 11.5 9.44 ? 10.4 10.0 ? 12.2 10.0 ? 11.1 5 5 5 5 15.9 14.4 16.9 15.4 150 150 120 60 942 1041 885 975 7.0 7.0 8.0 8.0 plad15kp10 plad15kp10a plad15kp11 plad15kp11a 10 10 11 11 11.1 ? 13.6 11.1 ? 12.3 12.2 ? 14.9 12.2 ? 13.5 5 5 5 5 18.8 17.0 20.1 18.2 45 45 10 10 798 882 747 822 9.0 9.0 10 10 plad15kp12 plad15kp12a plad15kp13 plad15kp13a 12 12 13 13 13.3 ? 16.3 13.3 ? 14.7 14.4 ? 17.6 14.4 ? 15.9 5 5 5 5 22.0 19.9 23.8 21.5 10 10 10 10 681 753 630 696 11 11 12 12 plad15kp14 plad15kp14a plad15kp15 plad15kp15a 14 14 15 15 15.6 ? 19.1 15.6 ? 17.2 16.7 ? 20.4 16.7 ? 18.5 5 5 5 5 25.8 23.2 26.9 24.4 10 10 10 10 582 645 564 318 13 13 15 15 plad15kp16 plad15kp16a plad15kp17 plad15kp17a 16 16 17 17 17.8 ? 21.8 17.8 ? 19.7 18.9 ? 23.1 18.9 ? 20.9 5 5 5 5 28.8 26.0 30.5 27.6 10 10 10 10 528 576 492 543 18 16 19 18 plad15kp18 plad15kp18a plad15kp20 plad15kp20a 18 18 20 20 20.0 ? 24.4 20.0 ? 22.1 22.2 ? 27.1 22.2 ? 24.5 5 5 5 5 32.2 29.2 35.8 32.4 10 10 10 10 465 516 417 462 20 19 24 22 plad15kp22 plad15kp22a plad15kp24 plad15kp24a 22 22 24 24 24.4 ? 29.8 24.4 ? 26.9 26.7 ? 32.6 26.7 ? 29.5 5 5 5 5 39.4 35.5 43.0 38.9 10 10 10 10 381 423 348 384 27 24 30 27 plad15kp26 plad15kp26a plad15kp28 plad15kp28a 26 26 28 28 28.9 ? 35.3 28.9 ? 31.9 31.1 ? 38.0 31.1 ? 34.4 5 5 5 5 46.6 42.1 50.1 45.5 10 10 10 10 321 357 297 330 33 29 34 30 plad15kp30 plad15kp30a plad15kp33 plad15kp33a 30 30 33 33 33.3 ? 40.7 33.3 ? 36.8 36.7 ? 44.9 36.7 ? 40.6 5 5 5 5 53.5 48.4 59.0 53.3 10 10 10 10 279 309 255 282 38 35 41 38 plad15kp36 plad15kp36a plad15kp40 plad15kp40a 36 36 40 40 40.0 ? 48.9 40.0 ? 44.2 44.4 ? 54.3 44.4 ? 49.1 5 5 5 5 64.3 58.1 71.4 64.5 10 10 10 10 234 258 210 234 45 40 50 45 plad15kp43 plad15kp43a plad15kp45 plad15kp45a 43 43 45 45 47.8 ? 58.4 47.8 ? 52.8 50.0 ? 61.1 50.0 ? 55.3 5 5 5 5 76.7 69.4 80.3 72.7 10 10 10 10 195 216 186 207 54 49 57 51 plad15kp48 plad15kp48a plad15kp51 plad15kp51a 48 48 51 51 53.3 ? 65.1 53.3 ? 58.9 56.7 ? 69.3 56.7 ? 62.7 5 5 5 5 85.5 77.4 91.1 82.4 10 10 10 10 174 195 165 183 62 55 65 60 8700 e. thomas rd. po box 1390, scottsdale, az 85252 usa, (480) 941-6300, fax: (480) 947-1503
15,000 w surface mount transient voltage suppressor microsemi scottsdale division page 3 copyright ? 2007 10-12-2007 rev g www. micr o semi . com scottsdale division plad15kp5.0 thru plad15kp400ca, e3 plad15kp5.0- 400ca, e3 microsemi part number (note 2) reverse stand- off voltage v wm (note 1) volts breakdown voltage v (br) v (br) @ i (br) volts ma maximum clamping voltage v c @ i pp volts maximum standby current i d @ v wm a maximum peak pulse current i pp (fig. 3) a maximum temperature coefficient of v (br) v(br ) mv/ oc plad15kp54 plad15kp54a plad15kp58 plad15kp58a 54 54 58 58 60.0 ? 73.3 60.0 ? 66.3 64.4 ? 78.7 64.4 ? 71.2 5 5 5 5 96.3 87.1 103.0 93.6 10 10 10 10 156 171 147 159 70 64 77 69 plad15kp60 plad15kp60a plad15kp64 plad15kp64a 60 60 64 64 66.7 ? 81.5 66.7 ? 73.7 71.1 ? 86.9 71.1 ? 78.6 5 5 5 5 107.0 96.8 114.0 103.0 10 10 10 10 141 156 132 147 79 70 85 75 plad15kp70 plad15kp70a plad15kp75 plad15kp75a 70 70 75 75 77.8 ? 95.1 77.8 ? 86.0 83.3 ? 102.0 83.3 ? 92.1 5 5 5 5 125 113 134 121 10 10 10 10 120 132 111 123 93 84 100 90 plad15kp78 plad15kp78a plad15kp85 plad15kp85a 78 78 85 85 86.7 ? 106.0 86.7 ? 95.8 94.4 ? 115.0 94.4 ? 104.0 5 5 5 5 139 126 151 137 10 10 10 10 108 120 99 108 104 94 113 102 plad15kp90 plad15kp90a plad15kp100 plad15kp100a 90 90 100 100 100 ? 122 100 ? 111 111 ? 136 111 ? 123 5 5 5 5 160 146 179 162 10 10 10 10 93 102 84 93 120 109 134 122 plad15kp110 plad15kp110a plad15kp120 plad15kp120a 110 110 120 120 122 ? 149 122 ? 135 133 ? 163 133 ? 147 5 5 5 5 196 177 214 193 10 10 10 10 78 84 70 78 147 132 161 145 plad15kp130 plad15kp130a plad15kp150 plad15kp150a 130 130 150 150 144 ? 176 144 ? 159 167 ? 204 167 ? 185 5 5 5 5 231 209 268 243 10 10 10 10 65 71 56 62 174 157 202 183 plad15kp160 plad15kp160a plad15kp170 plad15kp170a 160 160 170 170 178 ? 218 178 ? 197 189 ? 231 189 ? 209 5 5 5 5 287 259 304 275 10 10 10 10 52 58 49 55 216 195 229 207 plad15kp180 plad15kp180a plad15kp200 plad15kp200a 180 180 200 200 200 ? 244 200 ? 221 222 ? 271 222 ? 245 5 5 5 5 321 291 356 322 10 10 10 10 47 52 42 47 242 219 269 243 plad15kp220 plad15kp220a plad15kp250 plad15kp260a 220 220 250 260 245 ? 299 245 ? 271 278 ? 308 289 ? 320 5 5 5 5 293 356 403 419 10 10 10 10 38 42 37 35.5 297 269 306 318 plad15kp280a plad15kp300a plad15kp350a plad15kp400a 280 300 350 400 311 ? 345 333 ? 369 389 ? 431 444 - 492 5 5 5 5 451 483 564 644 10 10 10 10 33 31 26.5 23 344 368 430 490 note 1: transient voltage suppressors are normally selected with reverse ?stand off voltage? v wm which should be equal to or greater than the dc or continuous peak operating voltage level. note 2: for bidirectional construction, indicate a c or ca suffix after the part number. symbols & definitions symbol definition symbol definition v wm working peak (standoff) voltage i pp peak pulse current p pp peak pulse power v c clamping voltage v (br) breakdown voltage i (br) breakdown current for v (br) i d standby current 8700 e. thomas rd. po box 1390, scottsdale, az 85252 usa, (480) 941-6300, fax: (480) 947-1503
15,000 w surface mount transient voltage suppressor microsemi scottsdale division page 4 copyright ? 2007 10-12-2007 rev g www. micr o semi . com scottsdale division plad15kp5.0 thru plad15kp400ca, e3 plad15kp5.0- 400ca, e3 graphs p pp peak pulse power - kw tp ? pulse time ? sec figure 1 peak pulse power vs. pulse time to 50% of exponentially decaying pulse peak pulse power (p pp ) or continuous power in percent of 25 o c rating t l lead temperature o c test waveform parameters: tr=10 s, tp=1000 s figure 2 figure 3 pulse waveform derating curve 8700 e. thomas rd. po box 1390, scottsdale, az 85252 usa, (480) 941-6300, fax: (480) 947-1503
15,000 w surface mount transient voltage suppressor microsemi scottsdale division page 5 copyright ? 2007 10-12-2007 rev g www. micr o semi . com scottsdale division plad15kp5.0 thru plad15kp400ca, e3 plad15kp5.0- 400ca, e3 package and mounting pad dimensions inches [mm] 8700 e. thomas rd. po box 1390, scottsdale, az 85252 usa, (480) 941-6300, fax: (480) 947-1503
|