View STEVAL-TDR028V1_3262777.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

june 2010 doc id 17469 rev 1 1/11 11 STEVAL-TDR028V1 rf power amplifier demonstrat ion board based on the stac2942b features excellent thermal stability frequency: 87.5 - 108 mhz supply voltage: 48 v output power: 370 w min. gain: 20 db typ. efficiency: 77% typ. harmonics: - 30 dbc max. gain flatness: 0.7 db max. description the STEVAL-TDR028V1 is an rf broadband power amplifier intended for fm broadcast radio transmitters over the 87.5 to 108 mhz band, using an stac2942b gold metallized n-channel mos field-effect transistor. the STEVAL-TDR028V1 is designed in cooperation with innovaction s.r.l in italy. table 1. device summary order code STEVAL-TDR028V1 STEVAL-TDR028V1 www.st.com
contents STEVAL-TDR028V1 2/11 doc id 17469 rev 1 contents 1 electrical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1 maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3 circuit layout and connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 4 stac2942b mounting recommendat ions . . . . . . . . . . . . . . . . . . . . . . . . 5 4.1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4.2 heatsink selection and preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4.3 surface conditions of the mounting base . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4.4 thermal interface material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4.5 seating plane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4.6 printed circuit board (pcb) cons iderations . . . . . . . . . . . . . . . . . . . . . . . . 7 4.7 package attachment to thermal base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4.7.1 hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4.7.2 procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4.8 electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4.9 conclusion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 5 revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
STEVAL-TDR028V1 electrical data doc id 17469 rev 1 3/11 1 electrical data 1.1 maximum ratings 2 electrical characteristics t a = +25 o c, v dd = 48 v, i dq = 2 x 200 ma table 2. absolute maximum ratings symbol parameter value unit p in input power 7 w p out output power 400 w t stg storage temperature range -20 to +70 c t c operating base plate temperature 0 to +70 c i dd drain current 12 a p diss power dissipation 250 w table 3. electrical specification symbol test conditions min typ max unit frequency frequency range 87.5 108 mhz p out 370 400 w gain p out = 370 w 20 1 db nd p out = 370 w 77 % h2 2 nd harmonic @ p out = 370 w -35 dbc h3 3 rd harmonic @ p out = 370 w -41 dbc fl gain flatness @ p out = 370 w 0.7 db
circuit layout and connections STEVAL-TDR028V1 4/11 doc id 17469 rev 1 3 circuit layout and connections figure 1. circuit layout and connections
STEVAL-TDR028V1 stac2942b mounting recommendations doc id 17469 rev 1 5/11 4 stac2942b mounting recommendations 4.1 introduction rf power transistors are amongst the highest power density devices in the semiconductor industry. it is crucial to the reliability and pe rformance of such devices to give additional consideration to mechanical stresses and thermal and electrical resistances within the application environment. the general purpose of this section is to provide guidelines for mechanically mounting stac? boltdown packages so as to minimize stress and resistance. more specifically, attention is paid to the stac244b and st ac265b package families which are used for various vdmos and ldmos products. 4.2 heatsink selection and preparation the choice of heatsinking system depends on the specific device and application needs; this decision results in the total power di ssipation capability for the amplifier assembly. in most cases, the power transistor may be moun ted directly to a typical heatsink, such as a low-cost, extruded aluminum heatsink with fins. such a system has good thermal and electrical properties for most operating conditions. in cases of higher power dissipation, additional spreading of the thermal flux can be managed with a copper core heat-spreading layer between the transistor and heatsink. such a system can be designed for excellent thermal and electrical properties for the most demanding operating conditions. when the operating conditions of the device are such that the dissipated power is low, for example in low duty cycle or back-off power conditions, a basic thermal core layer without fins may be all that is required to maintain a high mttf or adherence to a maximum rating. the preferred material layer to which the package is attached is ofhc (uns c10100) copper, but may also be a lower quality copper or aluminum as required by detailed application needs. based on requirements for typical applications, the thickness of this layer is expected to be: min.: 0.12 in (3.0 mm) typ.: 0.22 in (5.6 mm) max.: 0.32 in (8.1 mm) since holes are to be tapped into the thermal core layer for device attachment, it is advised to drill and tap through the en tire layer whenever possible. for the recommended screws, the minimum tapped hole depth should be 0.12 in (3.0 mm). by design, the stac244b and stac265b package family do not require complex heatsink or core preparation, such as channels, pockets, cavities, etc., assuming a typical pcb thickness is selected for the application.
stac2942b mounting recommendations STEVAL-TDR028V1 6/11 doc id 17469 rev 1 4.3 surface conditions of the mounting base the mounting base, or surface of the heatsink to which the backside of the package is mounted, must be flat, clean, and free of tool marks. flatness: 400 in/in (0.4 m/mm) roughness: ra<30 in (0.8 m) flatness and roughness values can be achieved on the above-mentioned materials with standard machining proces ses, such as milling. holes for screws, solder wells, etc. should be slightly countersunk and/or de-burred. 4.4 thermal interface material careful consideration must be paid to the actual interface layer between the backside of the package and the mounting base. cleanliness is key: particulates, grease, and oxidation should be removed using standard practices. a thermal interface material (tim) of good thermal conductivity sh ould be used in order to fill any discontinuities between the package and mo unting base surface. the decision of which tim material to use is based on many factors. many types of tims are available today with an incredible range of thermal/electrical/mechanical properties. several are listed here: wpsii (a silicone-free compoun d, austerlitz electronics), type 340 (dow corning) type 120 (a silico ne compound, wakefiel d thermal solutions) indium foil (indium corp.) sn63pb37 or pb-free solder in all cases, the chosen tim should be no thicker than necessary and applied as evenly as possible. for liquid compounds, it is easiest to apply to the backside of the package, keeping in mind that excessive tim thickness results in a higher thermal resistance than using no tim at all. for foils and soldering it is best to specify an appropriately-sized ?preform? and apply it to the thermal base. 4.5 seating plane the seating plane refers to the distance between the thermal base and the bottom of the transistor leads. this is shown on the package outline drawing to indicate the total thickness of the pcb, or pcb+channel depth of the heatsink. some points to consider are: the leads of the transistor should launch perpendicular to the package body onto the traces of the pcb to reduce mechanical stress to the package and solder joints. in some cases, the pcb fabrication tolerances are such that the leads extend above the plane defined by the top of the pcb; this situation is best handled with a judicious selection of solder pad preform or paste thickness, or by a slight downward bending of the transistor leads (no more than 0.01 in (0.25 mm). in no case should the leads be
STEVAL-TDR028V1 stac2942b mounting recommendations doc id 17469 rev 1 7/11 bent higher than the topside of the pcb, to avoid shear stresses which could cause damage to the interface between the lead and the package body. care should be taken to factor in the thickness of the tim used, which is equivalent to increasing the seating plane dimension. if the pcb is fused to the heatsink by means of a bonding film, solder layer, etc., the corresponding thickness of this layer should be factored into the pcb thickness. 4.6 printed circuit board (pcb) considerations it is advisable to specify a ?package-cut?, or slot, through the board and mount the transistor directly to the heatsink for optimum performanc e. the dimensions for this slot should be approximately 0.010 to 0.025 in (0.25 to 0.6 mm) larger than the outside dimensions of the package body to ensure a good fit and to relieve stress upon the leads. these packages were designed to be compatible with pcbs having dielectric thicknesses in the range of 0.020 to 0.060 in (0.51 to 1.52 mm) - a wide range, covering a large scope of applications. as a general rule, as the thickness of the pcb increases within this range, the greater the offset dimensions for the slot should be designed. often, the pcb traces are slightly pulled back from the edge of the slot, which is also helpful in reducing stress upon the leads of the device. solder pad layouts for the transistor leads should be designed to be as large as the circuit topology allows, but it is recommended that pad area be at least the maximum width and remaining length of the leads (approximately 0.15 in or 3.8 mm). in most cases a border around the leads of at least 0.01 in (0.25 mm) for solder is advised, which allows for a good sold er fillet along three si des of each transistor lead. 4.7 package attachment to thermal base 4.7.1 hardware the recommended fastener system consists of: 2 4unc (or m3) torx, hex or phillips cap scr ews (one for each end of the package body) 2 spring washers, id=0.150? (3.81 mm) od=0.275? (6.98 mm) t=0.015? (0.38 mm) h=0.025? (0.62 mm) the procedure begins with the application of the tim to the back of the package, followed by the insertion of the package into the application board. it is best to start the screws in both tapped holes, continuing in an alternating fashion to insure the package is seated flat and without obstructions. to evenly distribute the pressure from the screw head/split washer combination, a flat washer with an outer diameter no greater than 0.28 in (7.1 mm) can be inserted between the split washer and the package body. as a substitute for a split washer, a conica l, belleville, or wave washer can be used. when this system is properly applied, uniform pressure with tolerance for thermal expansion is provided. the mechanical features designed into the stac? boltdown package translate the force toward the center of the package at the prescribed screw torque. along with the
stac2942b mounting recommendations STEVAL-TDR028V1 8/11 doc id 17469 rev 1 material set featuring low creep and fatigue resistance, the complete system insures that pressure is maintained uniformly over time. 4.7.2 procedure tighten both fastener systems to each end of the package body to a ?finger-tight? condition, approximately 0.4 in-lb (0.05 n-m, 0.5 kg-cm). use a torque driver or equivalent means to tighten both screws to the recommended torque of 5 in-lbs (0.6 n-m, 5.8 kg-cm). depending upon the choice of tim, the required torque may be adjusted within the following ranges without mechanical damage to the device: min.: 3.5 in-lb (0.4 n-m, 4 kg-cm) max.: 6.5 in-lb (0.75 n-m, 7.5 kg-cm) 4.8 electrical connection leads and/or flanges should be attached to the pcb and/or copper heatsinks using typical sn63pb37 or pb-free solders, in accordance with the supplier's recommendations. however, the following guidelines with respec t to the package should be considered: avoid, as much as possible, the use of flux or flux solutions as it is a potential source of contamination to the device. the leads of the transistor may be tinned prior to assembly into the pcb. this practice is used in situations when it is undesirable to introduce even a small amount of gold into the solder composition, fore stalling the possibility of sold er embrittlement issues. the source of au stems from the lead and/or backside surfaces, which are plated with 40 to 100 in (1 to 2.5 m) of au. the amount of solder to be used depends on the type of solder and the amount of allowable au in the final solder composition. it is desirable to increase the amount of solder when au content is a concern, such as in pb-free soldering applications. it is recommended to use either a solder preform or solder paste having a thickness of 0.001 to 0.010 in (0.03 to 0.3 mm), typically 0.006 in (.15 mm). adjustment of the solder preform or paste thickness may be used advantageously to account for thickness variations in the pcb manufacturing process. in cases where the backside of the flange is soldered to a copper core or heatsink, the package design and previously discussed mechanical mounting procedure provide sufficient downward pressure on the solder preform, resulting in a thin, high-quality bondline after a typical solder reflow procedure. in such cases, solder-wells or a solder- moat around the perimeter of the flange should be considered, to provide a region for excess solder to flow.
STEVAL-TDR028V1 stac2942b mounting recommendations doc id 17469 rev 1 9/11 4.9 conclusion this section has provided a set of guidelines to be considered for the proper attachment of the stac244b and stac265b packages in the majority of applications. in most cases, these recommendations are expected to result in reliable mechanical, electrical, and thermal performance. in terms of thermal resistance, these recommendations should provide an exceptionally low thermal resistance between the transistor case and the mounting base (r thc-mb ), on the order of 0.05 c/w for most products.
revision history STEVAL-TDR028V1 10/11 doc id 17469 rev 1 5 revision history table 4. document revision history date revision changes 03-jun-2010 1 initial release.
STEVAL-TDR028V1 doc id 17469 rev 1 11/11 please read carefully: information in this document is provided solely in connection with st products. stmicroelectronics nv and its subsidiaries (?st ?) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described he rein at any time, without notice. all st products are sold pursuant to st?s terms and conditions of sale. purchasers are solely responsible for the choice, selection and use of the st products and services described herein, and st as sumes no liability whatsoever relating to the choice, selection or use of the st products and services described herein. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. i f any part of this document refers to any third party products or services it shall not be deemed a license grant by st for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoev er of such third party products or services or any intellectual property contained therein. unless otherwise set forth in st?s terms and conditions of sale st disclaims any express or implied warranty with respect to the use and/or sale of st products including without limitation implied warranties of merchantability, fitness for a parti cular purpose (and their equivalents under the laws of any jurisdiction), or infringement of any patent, copyright or other intellectual property right. unless expressly approved in writing by an authorized st representative, st products are not recommended, authorized or warranted for use in milita ry, air craft, space, life saving, or life sustaining applications, nor in products or systems where failure or malfunction may result in personal injury, death, or severe property or environmental damage. st products which are not specified as "automotive grade" may only be used in automotive applications at user?s own risk. resale of st products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by st for the st product or service described herein and shall not create or extend in any manner whatsoev er, any liability of st. st and the st logo are trademarks or registered trademarks of st in various countries. information in this document supersedes and replaces all information previously supplied. the st logo is a registered trademark of stmicroelectronics. all other names are the property of their respective owners. ? 2010 stmicroelectronics - all rights reserved stmicroelectronics group of companies australia - belgium - brazil - canada - china - czech republic - finland - france - germany - hong kong - india - israel - ital y - japan - malaysia - malta - morocco - philippines - singapore - spain - sweden - switzerland - united kingdom - united states of america www.st.com

▲Up To Search▲

Price & Availability of STEVAL-TDR028V1

	To Download STEVAL-TDR028V1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .