? semiconductor components industries, llc, 2000 october, 2000 rev. 3 1 publication order number: mbrs130lt3/d mbrs130lt3 preferred device schottky power rectifier surface mount power package ...employs the s chottky barrier principle in a large area metaltosilicon power diode. stateoftheart geometry features epitaxial construction with oxide passivation and metal overlay contact. ideally suited for low voltage, high frequency rectification, or as free wheeling and polarity protection diodes, in surface mount applications where compact size and weight are critical to the system. ? very low forward voltage drop (0.395 volts max @ 1.0 a, t j = 25 c) ? small compact surface mountable package with jbend leads ? highly stable oxide passivated junction ? guardring for stress protection mechanical characteristics ? case: epoxy, molded ? weight: 95 mg (approximately) ? finish: all external surfaces corrosion resistant and terminal leads are readily solderable ? lead and mounting surface temperature for soldering purposes: 260 c max. for 10 seconds ? shipped in 12 mm tape and reel, 2500 units per reel ? cathode polarity band ? marking: 1bl3 maximum ratings rating symbol value unit peak repetitive reverse voltage working peak reverse voltage dc blocking voltage v rrm v rwm v r 30 v average rectified forward current t l = 120 c t l = 110 c i f(av) 1.0 2.0 a nonrepetitive peak surge current (surge applied at rated load conditions halfwave, single phase, 60 hz) i fsm 40 a operating junction temperature t j 65 to +125 c device package shipping ordering information smb case 403a plastic http://onsemi.com mbrs130lt3 smb 2500/tape & reel schottky barrier rectifier 1.0 ampere 30 volts preferred devices are recommended choices for future use and best overall value. marking diagram 1bl3 1bl3 = device code
mbrs130lt3 http://onsemi.com 2 thermal characteristics rating symbol value unit thermal resistance e junction to lead (t l = 25 c) r q jl 12 c/w electrical characteristics maximum instantaneous forward voltage (note 1.) (i f = 1.0 a, t j = 25 c) (i f = 2.0 a, t j = 25 c) v f 0.395 0.445 volts maximum instantaneous reverse current (note 1.) (rated dc voltage, t j = 25 c) (rated dc voltage, t j = 100 c) i r 1.0 10 ma 1. pulse test: pulse width = 300 m s, duty cycle 2%. i f , instantaneous forward current (amps) 10 5.0 2.0 1.0 0.5 0.2 0.1 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 v f , instantaneous voltage (volts) figure 1. typical forward voltage t j = 100 c 25 c i r , reverse leakage current (ma) 100 10 1.0 0.1 0.01 0.001 0 3 6 9 12 15 18 21 24 27 30 v r , reverse voltage (volts) figure 2. typical reverse leakage current t j = 100 c 25 c i f(av) , average forward current (amps) 8 7 6 5 4 3 2 1 0 50 60 70 80 90 100 110 120 130 t c , case temperature ( c) figure 3. current derating (case) square wave dc t j = 100 c p f(av) , average power dissipation (watts) 8 7 6 5 4 3 2 1 0 01 2 34 5 67 8 i f(av) , average forward current (amps) figure 4. typical power dissipation 20 10 5 dc i pk i av = square wave rated voltage applied r q jc = 12 c/w t j = 100 c
mbrs130lt3 http://onsemi.com 3 c, capacitance (pf) 400 350 300 250 200 150 100 50 0 0 4 8 12162024 2832 v r , reverse voltage (volts) figure 5. typical capacitance note: typical capacitance at 0 v = 290 pf package dimensions smb plastic package case 403a03 issue d a s d b j p k c h notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: inch. 3. d dimension shall be measured within dimension p. dim min max min max millimeters inches a 0.160 0.180 4.06 4.57 b 0.130 0.150 3.30 3.81 c 0.075 0.095 1.90 2.41 d 0.077 0.083 1.96 2.11 h 0.0020 0.0060 0.051 0.152 j 0.006 0.012 0.15 0.30 k 0.030 0.050 0.76 1.27 p 0.020 ref 0.51 ref s 0.205 0.220 5.21 5.59
mbrs130lt3 http://onsemi.com 4 on semiconductor and are trademarks of semiconductor components industries, llc (scillc). scillc reserves the right to make changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. atypicalo parameters which may be provided in scill c data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. all operating parameters, including atypicalso must be validated for each customer application by customer's technical experts. scillc does not convey any license under its patent rights nor the rights of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body , or other applications intended to support or sustain life, or for any other application in which the failure of the scillc product could create a sit uation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indemnify and hold scillc and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthori zed use, even if such claim alleges that scillc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. publication ordering information central/south america: spanish phone : 3033087143 (monfri 8:00am to 5:00pm mst) email : onlitspanish@hibbertco.com tollfree from mexico: dial 018002882872 for access then dial 8662979322 asia/pacific : ldc for on semiconductor asia support phone : 3036752121 (tuefri 9:00am to 1:00pm, hong kong time) toll free from hong kong & singapore: 00180044223781 email : onlitasia@hibbertco.com japan : on semiconductor, japan customer focus center 4321 nishigotanda, shinagawaku, tokyo, japan 1410031 phone : 81357402700 email : r14525@onsemi.com on semiconductor website : http://onsemi.com for additional information, please contact your local sales representative. mbrs130lt3/d north america literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 3036752175 or 8003443860 toll free usa/canada fax : 3036752176 or 8003443867 toll free usa/canada email : onlit@hibbertco.com fax response line: 3036752167 or 8003443810 toll free usa/canada n. american technical support : 8002829855 toll free usa/canada europe: ldc for on semiconductor european support german phone : (+1) 3033087140 (monfri 2:30pm to 7:00pm cet) email : onlitgerman@hibbertco.com french phone : (+1) 3033087141 (monfri 2:00pm to 7:00pm cet) email : onlitfrench@hibbertco.com english phone : (+1) 3033087142 (monfri 12:00pm to 5:00pm gmt) email : onlit@hibbertco.com european tollfree access*: 0080044223781 *available from germany, france, italy, uk, ireland
|
