53 type 592d solid tantalum chip capacitors t antamount ? , low profile, conformal terminals, maximum c/v at + 125 c: leakage current shall not exceed 12 times the values listed in the standard ratings tables. life test: capacitors shall withstand rated dc voltage applied at + 85 c for 2000 hours or derated dc voltage applied at + 125 c for 1000 hours. following the life test: 1. dcl shall meet the original requirement. 2. dissipation factor and esr shall meet the original requirement. 3. change in capacitance shall not exceed 10%. performance characteristics performance characteristics performance characteristics performance characteristics performance characteristics operating temperature: - 55 c to + 85 c. (to + 125 c with voltage derating.) capacitance tolerance: at 120 hz, + 25 c. 20% standard. 10% available. dissipation factor: at 120 hz, + 25 c. dissipation factor, as determined from the expression 2 p frc, shall not exceed the values listed in the standard ratings tables. dc leakage current (dcl max.): at + 25 c: leakage current shall not exceed the values listed in the standard ratings tables. at + 85 c: leakage current shall not exceed 10 times the values listed in the standard ratings tables. electrical characteristics @ + 25 electrical characteristics @ + 25 electrical characteristics @ + 25 electrical characteristics @ + 25 electrical characteristics @ + 25 c c c c c dcl: .01 m a/cv or .5 m a whichever is greater. df: 4% 1 m f. 6% > 1 m f < 100 m f. 8% 3 100 m f. features features features features features ? ? ? ? ? new extended range offerings. ? ? ? ? ? new a case size offering. ? ? ? ? ? low profile .047" [1.2mm] height (nominal). ? ? ? ? ? compatible with 293d molded chip mounting pad layout. ? ? ? ? ? terminations: 60/40 tin lead (2) standard - (electro-plate or solder dip). ? ? ? ? ? operating temperature: - 55 c to + 125 c. ? ? ? ? ? low esr and inductance. ? ? ? ? ? case code compatibility with eia 535baac and cecc 30801 molded chips for length and width. dimensional configurations dimensional configurations dimensional configurations dimensional configurations dimensional configurations [numbers in brackets indicate millimeters] case code a b c d r l (max.) .146 [3.7] .158 [4.0] .281 [7.1] .293 [7.5] .285 [7.2] w .072 .010 [1.8 .3] .110 + .010 - .016 [2.8 + .3 - .4] .126 .010 [3.2 0.3] .170 .010 [4.3 0.3] .235 .010 [6.0 0.3] a .031 .012 [.80 .30] .031 .012 [.80 .30] .051 .012 [1.3 .30] .051 .012 [1.3 .30] .051 .012 [1.3 .30] b .085 .015 [2.2 0.4] .097 .015 [2.5 0.4] .180 .025 [4.6 0.6] .180 .025 [4.6 0.6] .180 .025 [4.6 0.6] d (ref.) .115 [2.9] .127 [3.2] .236 [6.0] .253 [6.4] .243 [6.2] j (max.) .004 [.01] .004 [0.1] .004 [0.1] .004 [0.1] .004 [0.1] h .047 .008 1.2 .2 .047 .012 [1.2 0.3] .047 .012 [1.2 0.3] .047 .012 [1.2 0.3] .047 .012 [1.2 0.3] j j tantalum wire nib identifies anode (+) terminal w d l b a h note: the anode termination (d less b) will be a minimum of .010" [0.3mm]. vishay sprague 70 pembroke road, concord, nh 03301 ? phone (603) 224-1961 ? fax 603-224-1430 ? internet www.vishay.com major vishay brands dale ? draloric ? foil resistors ? measurements group ? roederstein ? sfernice ? sprague ? thin film ? vitramon
54 m f 1.0 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 4 v type 592d type 592d type 592d type 592d type 592d 6.3 v 10 v 35 v 25 v 20 v 16 v ratings and case codes ratings and case codes ratings and case codes ratings and case codes ratings and case codes rated voltage vr @ + 85 c capacitance ( m f) 4 wvdc @ + 85 c, surge = 5.2 v . . . 2.7 wvdc @ + 125 c, surge = 3.4 v 22.0 22.0 47.0 47.0 68.0 68.0 100.0 100.0 150.0 0.9 0.9 1.9 1.9 2.7 2.7 4.0 4.0 6.0 6 6 6 6 6 6 8 8 8 2.4 1.6 1.5 0.40 0.35 0.27 0.26 0.20 0.20 0.16 0.22 0.23 0.50 0.53 0.68 0.69 0.87 0.87 a b b b c c d d r r 6 6 6 6 6 6 6 6 6 8 592d156x06r3a2t 592d156x06r3b2t 592d226x06r3b2t 592d336x06r3b2t 592d336x06r3c2t 592d476x06r3c2t 592d476x06r3d2t 592d686x06r3d2t 592d686x06r3r2t 592d107x06r3r2t 0.9 0.9 1.4 2.1 2.1 3.0 3.0 4.0 4.0 6.0 10.0 10.0 22.0 22.0 33.0 33.0 47.0 47.0 68.0* 68.0 6 6 6 6 6 6 6 6 6 6 2.6 1.7 1.5 0.40 0.40 0.30 0.27 0.20 0.27 0.20 1.0 1.0 2.2 2.2 3.3 3.3 4.7 4.7 6.8 6.8 0.80 1.10 1.10 1.60 1.60 2.40 2.40 3.50 3.50 5.30 6 6 6 6 6 6 6 6 6 6 0.13 0.13 0.21 0.22 0.32 0.24 0.50 0.46 0.60 0.62 a b b c c d d r d* r 592d106x0010a2t 592d106x0010b2t 592d226x0010b2t 592d226x0010c2t 592d336x0010c2t 592d336x0010d2t 592d476x0010d2t 592d476x0010r2t 592d686x0010d2t* 592d686x0010r2t 4.7 6.8 6.8 10 10 15* 15 22 22 33 a a b b c b* d c d d 592d475x0016a2t 592d685x0016a2t 592d685x0016b2t 592d106x0016b2t 592d106x0016c2t 592d156x0016b2t* 592d156x0016d2t 592d226x0016c2t 592d226x0016d2t 592d336x0016d2t 0.15 0.22 0.23 0.50 0.50 0.65 0.68 0.87 0.68 0.87 3.5 3.5 1.8 1.6 1.0 1.4 0.5 0.5 0.4 0.3 case code a b b c c d d r r part number** 592d226x0004a2t 592d226x0004b2t 592d476x0004b2t 592d476x0004c2t 592d686x0004c2t 592d686x0004d2t 592d107x0004d2t 592d107x0004r2t 592d157x0004r2t max. dcl @ + 25 c ( m a) max. df @ + 25 c 120 hz (%) max. esr @ + 25 c 100khz (ohms) 0.15 0.22 0.23 0.24 0.50 0.50 0.65 0.68 0.87 0.87 2.5 1.7 1.5 1.4 0.40 0.40 0.30 0.27 0.20 0.20 15.0 15.0 22.0 33.0 33.0 47.0 47.0 68.0 68.0 100.0 standard ratings standard ratings standard ratings standard ratings standard ratings max. ripple 100khz irms (amps) * contact factory for availability. ** part numbers shown for units with 20% capacitance tolerance. for 10% units, change "x0" to "x9". extended range * ratings shown in bold print. * contact factory for availability. this table shows the largest capacitance values available in the case size and voltage ind icated. vishay sprague 70 pembroke road, concord, nh 03301 ? phone (603) 224-1961 ? fax 603-224-1430 ? internet www.vishay.com major vishay brands dale ? draloric ? foil resistors ? measurements group ? roederstein ? sfernice ? sprague ? thin film ? vitramon ext a b c d r std b c d r ext a b c d std b c d r ext a b c d d* ext a b b* c d r std b c d r std b c d r ext a b b* c d r std b c d r ext a b c d r std b c d r ext a b c d r 6.3 wvdc @ + 85 c, surge = 8 v . . . 4 wvdc @ + 125 c, surge = 5 v 10 wvdc @ + 85 c, surge = 13 v . . . 7 wvdc @ + 125 c, surge = 8 v 16 wvdc @ + 85 c, surge = 20 v . . . 10 wvdc @ + 125 c, surge = 12 v std b c d r
55 type 592d type 592d type 592d type 592d type 592d 592d475x0020a2t 592d475x0020b2t 592d685x0020b2t 592d685x0020c2t 592d106x0020b2t* 592d106x0020d2t 592d156x0020c2t 592d156x0020r2t 592d226x0020d2t 592d226x0020r2t 592d336x0020r2t 0.9 0.9 1.4 1.4 2.0 2.0 3.0 3.0 4.4 4.4 6.6 6 6 6 6 6 6 6 6 6 6 6 3.80 3.20 3.10 1.10 3.00 0.50 0.60 0.40 0.40 0.28 0.28 0.13 0.16 0.16 0.30 0.16 0.48 0.42 0.65 0.56 0.73 0.73 4.7 4.7 6.8 6.8 10.0* 10.0 15.0 15.0 22.0 22.0 33.0 a b b c b* d c r d r r 2.2 2.2 3.3 3.3 4.7 6.8 6.8 10.0 10.0 15.0 a b b c c c d d r r 6 6 6 6 6 6 6 6 6 6 8.00 6.00 5.60 2.00 1.60 1.50 1.30 1.20 0.48 0.40 a b b c c d r d r r 10.0 6.50 6.00 3.50 3.20 2.10 1.30 1.30 1.20 1.20 0.08 0.11 0.12 0.17 0.18 0.24 0.34 0.31 0.35 0.35 4 4 6 6 6 6 6 6 6 6 0.5 0.5 0.8 0.8 1.2 1.2 1.6 2.4 2.4 3.5 592d105x0035a2t 592d105x0035b2t 592d225x0035b2t 592d225x0035c2t 592d335x0035c2t 592d335x0035d2t 592d475x0035r2t 592d685x0035d2t 592d685x0035r2t 592d106x0035r2t 0.6 0.6 0.8 0.8 1.2 1.7 1.7 2.5 2.5 3.8 592d225x0025a2t 592d225x0025b2t 592d335x0025b2t 592d335x0025c2t 592d475x0025c2t 592d685x0025c2t 592d685x0025d2t 592d106x0025d2t 592d106x0025r2t 592d156x0025r2t capacitance ( m f) case code part number** max. dcl @ + 25 c ( m a) max. df @ + 25 c 120 hz (%) max. esr @ + 25 c 100khz (ohms) standard ratings standard ratings standard ratings standard ratings standard ratings max. ripple 100khz irms (amps) 1.0 1.0 2.2 2.2 3.3 3.3 4.7 6.8 6.8 10.0 typical curves @ + 25 typical curves @ + 25 typical curves @ + 25 typical curves @ + 25 typical curves @ + 25 c, impedance and esr vs frequency c, impedance and esr vs frequency c, impedance and esr vs frequency c, impedance and esr vs frequency c, impedance and esr vs frequency "a" case 1000 100 10 1 0.1 100 1k 10k 100k 1m frequency in hertz frequency in hertz ohms impedance esr 1 m f, 35 vdc 15 m f, 6.3 vdc "b" case 1000 100 10 1 0.1 100 1k 10k 100k 1m 10 m f, 10 v 4.7 m f, 20 v ohms impedance esr 16 wvdc @ + 85 c, surge = 20 v . . . 10 wvdc @ + 125 c, surge = 12 v 5.30 7.5 6 6 0.75 0.77 33.0 47.0 r r 592d336x0016r2t 592d476x0016r2 t 0.27 0.25 vishay sprague 70 pembroke road, concord, nh 03301 ? phone (603) 224-1961 ? fax 603-224-1430 ? internet www.vishay.com major vishay brands dale ? draloric ? foil resistors ? measurements group ? roederstein ? sfernice ? sprague ? thin film ? vitramon * contact factory for availability. ** part numbers shown for units with 20% capacitance tolerance. for 10% units, change "x0" to x9." extended range * ratings shown in bold print. 20 wvdc @ + 85 c, surge = 26 v . . . 13 wvdc @ + 125 c, surge = 16 v 25 wvdc @ + 85 c, surge = 33 v . . . 17 wvdc @ + 125 c, surge = 20 v 35 wvdc @ + 85 c, surge = 46 v . . . 23 wvdc @ + 125 c, surge = 26 v 0.09 0.12 0.12 0.22 0.25 0.26 0.31 0.32 0.56 0.61
56 impedance esr 47 m f, 6.3 v 100 10 1 0.1 0.01 6.8 m f, 25 v frequency in hertz 100 1k 10k 100k 1m impedance esr 10 m f, 25 v 100 10 1 0.1 0.01 "r" case ohms frequency in hertz 100 1k 10k 100k 1m "c" case frequency in hertz 1000 100 10 1 0.1 4.7 m f, 25 v 100 1k 10k 100k 1m ohms ohms 33 m f, 6.3 v 100 m f, 6.3 v "d" case impedance esr how to order t reel size and packaging 592d type blank = bulk pack t = tape and reel 7" [178mm] reel w = 13" [330mm] reel see tape and reel specifications. 2 = 60/40 tin lead. standard. 2 termination see ratings and case codes table. b case code 010 dc voltage rating @ + 85 c this is expressed in volts. to complete the three-digit block, zeros precede the voltage rating. a decimal point is indicated by an "r" (6r3 = 6.3 volts). x0 capacitance tolerance 106 capacitance x0 = 20% x9 = 10% this is expressed in picofarads. the first two digits are the significant figures. the third is the number of zeros to follow. typical curves @ + 25 typical curves @ + 25 typical curves @ + 25 typical curves @ + 25 typical curves @ + 25 c, impedance and esr vs frequency c, impedance and esr vs frequency c, impedance and esr vs frequency c, impedance and esr vs frequency c, impedance and esr vs frequency type 592d type 592d type 592d type 592d type 592d vishay sprague 70 pembroke road, concord, nh 03301 ? phone (603) 224-1961 ? fax 603-224-1430 ? internet www.vishay.com major vishay brands dale ? draloric ? foil resistors ? measurements group ? roederstein ? sfernice ? sprague ? thin film ? vitramon note: parts qualified and identified to tighter capacitance tolerance and/or higher rated voltage, are substitutable for parts orde red to looser capacitance tolerance and/or lower rated voltage, provided other values, such as case size and termination remain the same.
57 notes: 1. a 0 b 0 k 0 are determined by the maximum dimensions to the ends of the terminals extending from the component body and/or the body dimensions of the component. the clearance between the ends of the terminals or body of the component to the sides and depth o f the cavity (a 0 b 0 k 0 ) must be within .002" [0.05mm] minimum and .020" [0.50mm] maximum. the clearance allowed must also prevent rotation of the component within the cavity of not more than 20 degrees. 2. tape with components shall pass around radius "r" without damage. the minimum trailer length may require additional length t o provide r minimum for 12mm embossed tape for reels with hub diameters approaching n minimum. 3. this dimension is the flat area from the edge of the sprocket hole to either the outward deformation of the carrier tape betw een the embossed cavities or to the edge of the cavity whichever is less. 4. this dimension is the flat area from the edge of the carrier tape opposite the sprocket holes to either the outward deformati on of the carrier tape between the embossed cavity or to the edge of the cavity whichever is less. 5. the embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. dimensions of embossment location and hole location shall be applied independent of each other. 6. b 1 dimension is a reference dimension for tape feeder clearance only. type 592d type 592d type 592d type 592d type 592d tape and reel packaging tape and reel packaging tape and reel packaging tape and reel packaging tape and reel packaging [numbers in brackets indicate millimeters] note: metric dimensions will govern. dimensions in inches are rounded and for reference only. units per reel 13" [330] reel 10000 8000 4000 4000 4000 2500 2000 1000 1000 1000 7" [178] reel component pitch tape width case code 4mm 4mm 8mm 8mm 8mm 8mm 12mm 12mm 12mm 12mm a b c d r 8mm 12mm 12mm double pitch tape size .179 [4.55] .323 [8.2] .323 [8.2] b 1 (max.) (note 6) .039 [1.0] .059 [1.5] .059 [1.5] d 1 (min.) (note 5) .138 .002 [3.5 0.05] .217 .002 [5.5 0.05] .217 .002 [5.5 0.05] f a 0 b 0 k 0 .315 + .012 - .004 [8.0 + 0.3 - 0.1] .472 .012 [12.0 .30] .472 .012 [12.0 .30] w .098 [2.5] .256 [6.5] .256 [6.5] t 2 (max.) .984 [25.0] 1.181 [30.0] 1.181 [30.0] r (min.) (note 2) p 1 (note 1) .157 .004 [4.0 0.1] .157 .004 [4.0 0.10] .315 .004 [8.0 0.10] tape and reel specifications: all case sizes are available on plastic embossed tape per eia-481-1. tape reeling per iec 286-3 is also available. standard reel diameter is 7" [178mm]. 13" [330mm] reels are available and recommended as the most cost effective packaging method. the most efficient packaging quantities are full reel increments on a given reel diameter. the quantities shown allow for the sealed empty pockets required to be in conformance with eia-481-1. reel size and packaging orientation must be specified in the vishay sprague part number. camber (top view) allowable camber to be .039/3.937 [1/100] non-cumulative over 9.843 [250.0] .039 [1.0] max. tape (top view) embossment carrier top cover tape thickness standard orientation is with the cathode (-) nearest to the sprocket holes per eia-481-1 and iec 286-3. bending radius (note 2) user direction of feed .030 [0.75] min. (note 3) center lines of cavity a 0 p 1 .030 [0.75] min. (note 4) top cover tape deformation between embossments embossment maximum cavity size (note 1) .079 .002 [2.0 0.05] .157 .004 [4.0 0.10] f .069 .004 [1.75 0.10] 10 pitches cumulative tolerance on tape 0.008 [0.200] 20 maximum component rotation .039 [1.0] max. 9.843 [250.0] 3.937 [100.0] top cover tape r min. d 1 min. for components .079 x .047 [2.0 x 1.2] and larger. (note 5) t 2 max. .024 [0.600] max. b 1 max. (note 6) .004 [0.10] max. for tape feeder reference only including draft. concentric around b 0 (note 5) typical component cavity center line typical component center line b 0 a 0 b 0 w (side or front sectional view) maximum component rotation 20 k 0 vishay sprague 70 pembroke road, concord, nh 03301 ? phone (603) 224-1961 ? fax 603-224-1430 ? internet www.vishay.com major vishay brands dale ? draloric ? foil resistors ? measurements group ? roederstein ? sfernice ? sprague ? thin film ? vitramon .059 + .004 - 0.0 [1.5 + 0.10 - 0.0]
58 type 592d where, p = power dissipation in watts @ + 25 c as given in the table in paragraph number 5 (power dissipation). r esr = the capacitor equivalent series resistance at the specified frequency. 2. a-c ripple voltage: the maximum allowable ripple voltage shall be determined from the formula: or, from the formula: v rms = i rms x z where, p = power dissipation in watts @ + 25 c as given in the table in paragraph number 5 (power dissipation). r esr = the capacitor equivalent series resistance at the specified frequency. z = the capacitor impedance at the specified frequency. 2.1 the sum of the peak ac voltage plus the dc voltage shall not exceed the dc voltage rating of the capacitor. 2.2 the sum of the negative peak ac voltage plus the applied dc voltage shall not allow a voltage reversal exceeding 10% of the dc working voltage at + 25 c. 3. reverse voltage: these capacitors are capable of withstanding peak voltages in the reverse direction equal to 10% of the dc rating at + 25 c and 5% of the dc rating at + 85 c. 4. temperature derating: if these capacitors are to be operated at temperatures above + 25 c, the permissible rms ripple current or voltage shall be calculated using the derating factors as shown: guide to application 1. a-c ripple current: the maximum allowable ripple current shall be determined from the formula: p r esr i rms = z v rms = p r esr a b c d r maximum permissible power dissipation @ + 25 c (watts) in free air case code 6. recommended mounting pad geometries: the nib must have sufficient clearance to avoid electrical contact with other components. the width dimension indicated is the same as the maximum width of the capacitor. this is to minimize lateral movement. derating factor 1.0 0.9 0.8 0.4 temperature + 25 c + 55 c + 85 c + 125 c 5. power dissipation: power dissipation will be affected by the heat sinking capability of the mounting surface. non-sinusoidal ripple current may produce heating effects which differ from those shown. it is important that the equivalent irms value be established when calculating permissible operating levels. (power dissipation calculated using + 25 c temperature rise.) [numbers in brackets indicate millimeters] * pads for b, c and d case codes are otherwise pad compatible * with type 293d, b, c and d case codes respectively. reflow solder pads* width (a) pad metallization (b) separation (c) case code 0.060 0.080 0.100 0.125 0.150 vishay sprague 70 pembroke road, concord, nh 03301 ? phone (603) 224-1961 ? fax 603-224-1430 ? internet www.vishay.com major vishay brands dale ? draloric ? foil resistors ? measurements group ? roederstein ? sfernice ? sprague ? thin film ? vitramon a b b c a b c d r .082 [2.1] .120 [3.0] .136 [3.5] .180 [4.6] .245 [6.3] .065 [1.7] .065 [1.7] .090 [2.3] .090 [2.3] .090 [2.3] .050 [1.3] .065 [1.7] .120 [3.1] .145 [3.7] .145 [3.7]
|
