View HSD070I651-C00_2015528.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

h a n n sta r di sp l a y c o rp . document title hsd070i651 specification page no. 1 /26 document no. revision 1.0 the information contained in this document is the e xclusive property of hannstar display corporation. it shall not be disclosed, distributed or reproduced in whole or in part without written permission of hann star display corporation. to : date : customer acceptance specification model : hsd070i651- c00 note:1.please contact hannstar display corp. before designing your product based on this module specification. 2.the information contained herein is presente d merely to indicate the characteristics and performance of our products. no responsibility is a ssumed by hannstar for any intellectual property claims or other problems that may result f rom application based on the module described herein. www.datasheet.in
h a n n sta r di sp l a y c o rp . document title hsd070i651 specification page no. 2 /26 document no. revision 1.0 the information contained in this document is the e xclusive property of hannstar display corporation. it shall not be disclosed, distributed or reproduced in whole or in part without written permission of hann star display corporation. record of revisions rev. date description of change 1.0 april.4, 2006 cas of HSD070I651-C00 was first issued. www.datasheet.in
h a n n sta r di sp l a y c o rp . document title hsd070i651 specification page no. 3 /26 document no. revision 1.0 the information contained in this document is the e xclusive property of hannstar display corporation. it shall not be disclosed, distributed or reproduced in whole or in part without written permission of hann star display corporation. contents 1.0 general description . p.4 2.0 absolute maximum ratings . p.6 3.0 optical characteristics . p.7 4.0 block diagram .. .. p.11 5.0 interface pin connection . p.12 6.0 electrical characteristics . p.14 7.0 reliability test items p.21 8.0 outline dimension . p.22 9.0 lot mark ... p.23 10.0 package specification . p.24 11.0 general precaution . p.25 www.datasheet.in
h a n n sta r di sp l a y c o rp . document title hsd070i651 specification page no. 4 /26 document no. revision 1.0 the information contained in this document is the e xclusive property of hannstar display corporation. it shall not be disclosed, distributed or reproduced in whole or in part without written permission of hann star display corporation. 1.0 general description 1.1 introduction hannstar display model HSD070I651-C00 is a color ac tive matrix thin film transistor (tft) liquid crystal display (lcd) that uses amorphous silicon tft as a switching device. this model is composed of a tft l cd panel, a driving circuit and a back light system. this tft lcd has a 7.0 (16:9) inch diagonally measured active display area with 1440 x 234 dot (480 horizontal by 234 vertical pixel) resolution. 1.2 features 7 (16:9 diagonal) inch configuration compatible with ntsc & pal system image reversion: up/down and left/right 1.3 applications portable tv portable dvd multimedia applications and others av system 1.4 general information item specification unit outline dimension 164.9 x 100 x 5.5 (typ.) mm display area 154.08(h) x 86.58(v) mm number of pixel 480 rgb(h) x234(v) pixels pixel pitch 0.321(h) x 0.370(v) mm pixel arrangement rgb vertical stripe display mode normally white surface treatment antiglare, hard-coating(3h) with wv film weight 160 (typ.) g back-light single ccfl (side-light type) logic system 36.4(typ.) mw power consumption b/l system 3.28(typ.) w www.datasheet.in
h a n n sta r di sp l a y c o rp . document title hsd070i651 specification page no. 5 /26 document no. revision 1.0 the information contained in this document is the e xclusive property of hannstar display corporation. it shall not be disclosed, distributed or reproduced in whole or in part without written permission of hann star display corporation. 1.5 mechanical information item min. typ. max. unit horizontal(h) 164.4 164.9 165.4 mm vertical(v) 99.5 100.0 100.5 mm module size depth(d) 5.5 5.8 mm weight (without inverter) 160 170 g www.datasheet.in
h a n n sta r di sp l a y c o rp . document title hsd070i651 specification page no. 6 /26 document no. revision 1.0 the information contained in this document is the e xclusive property of hannstar display corporation. it shall not be disclosed, distributed or reproduced in whole or in part without written permission of hann star display corporation. 2.0 absolute maximum ratings 2.1 electrical absolute rating 2.1.1 tft lcd module item symbol min. max. unit note dv dd -0.3 6.0 v gnd=0 v gh -0.3 40 v gnd=0 v gl -20 0.3 v gnd=0 v gh - v gl -0.3 40 v av dd -0.3 7.0 v agnd=0 power supply voltage v com -1.6 5.2 v analog signal input level v r, v g, v b -0.2 av dd +0.2 v logic signal input level v i -0.3 dv dd +0.3 v 2.1.2 back-light unit item symbol min. max. unit note lamp current i l 0 7.0 ma (1) (2) lamp frequency f l 0 100 khz (1) (2) note (1) permanent damage may occur to the lcd modu le if beyond this specification. functional operation should be restricted to th e conditions described under normal operating conditions. (2) ta =252 2.2 environment absolute rating item symbol min. max. unit note operating temperature t opa -10 60 storage temperature t stg -20 70 www.datasheet.in
h a n n sta r di sp l a y c o rp . document title hsd070i651 specification page no. 7 /26 document no. revision 1.0 the information contained in this document is the e xclusive property of hannstar display corporation. it shall not be disclosed, distributed or reproduced in whole or in part without written permission of hann star display corporation. 3.0 optical characteristics 3.1 optical specification item symbol condition min. typ. max. unit note contrast cr 400 500 (1)(2) rising t r 5 7 response time falling t f 20 28 msec (1)(3) white luminance (center) y l 255 300 cd/m 2 (1)(4) (i l =6.0ma) w x 0.26 0.31 0.36 color chromaticity (cie1931) white w y =0 normal viewing angle 0.28 0.33 0.38 (1)(4) l 50 60 hor. r 50 60 u 30 40 viewing angle ver. d cr>10 50 60 brightness uniformity b uni =0 70 % (5) 3.2 measuring condition measuring surrounding : dark room lamp current i fl : 6.00.1ma(rms), lamp freq. f l =50khz, inverter : hiu-766-22pf ambient temperature : 252 o c 30min. warm-up time. www.datasheet.in
h a n n sta r di sp l a y c o rp . document title hsd070i651 specification page no. 8 /26 document no. revision 1.0 the information contained in this document is the e xclusive property of hannstar display corporation. it shall not be disclosed, distributed or reproduced in whole or in part without written permission of hann star display corporation. 3.3 measuring equipment otsuka electrics corp., which utilized lcd-7000 fo r chromaticity and bm-5 for other optical characteris tics. measuring spot size : 10 ~ 12 mm note (1) definition of viewing angle : note (2) definition of contrast ratio(cr) : measured at the center point of panel luminance with all pixels white cr = luminance with all pixels black l r u d =0 o =180 o 12 oclock =90 o 6 oclock =270 o www.datasheet.in
h a n n sta r di sp l a y c o rp . document title hsd070i651 specification page no. 9 /26 document no. revision 1.0 the information contained in this document is the e xclusive property of hannstar display corporation. it shall not be disclosed, distributed or reproduced in whole or in part without written permission of hann star display corporation. note (3) definition of response time : sum of t r and t f note (4) definition of optical measurement setup time optical response white(tft off) black (tft on) white(tft off) 100% 90% 10% 0% t r t f 50cm photo-detector (bm-5a) field=2 lcd panel center of panel www.datasheet.in
h a n n sta r di sp l a y c o rp . document title hsd070i651 specification page no. 1 0/26 document no. revision 1.0 the information contained in this document is the e xclusive property of hannstar display corporation. it shall not be disclosed, distributed or reproduced in whole or in part without written permission of hann star display corporation. note (5) definition of brightness uniformity luminance uniformity = 100% (min luminance of 9 points) (max luminance of 9 points) 25% 50% 75% 25% 50% 75% y 1 y 2 y 3 y 4 y 5 y 6 y 7 y 8 y 9 www.datasheet.in
h a n n sta r di sp l a y c o rp . document title hsd070i651 specification page no. 1 1/26 document no. revision 1.0 the information contained in this document is the e xclusive property of hannstar display corporation. it shall not be disclosed, distributed or reproduced in whole or in part without written permission of hann star display corporation. 4.0 block diagram 4.1 tft lcd module 4.2 pixel format 1,1 1,480 480 234 lcd display area 2,1 1,2 1,3 1,4 234 lines 480 pixels(1440 dots) 234,1 r r r b g 1 pixel scan driver source driver lcd panel input fpc ccfl cn1 cn2 www.datasheet.in
h a n n sta r di sp l a y c o rp . document title hsd070i651 specification page no. 1 2/26 document no. revision 1.0 the information contained in this document is the e xclusive property of hannstar display corporation. it shall not be disclosed, distributed or reproduced in whole or in part without written permission of hann star display corporation. 5.0 interface pin connection 5.1 tft lcd module cn2 (input signal): fpc down connector, 26 pins, pitch : 0.5mm terminal no. symbol i/o function note 1 dgnd - ground for logic circuit 2 dv dd i supply voltage of logic control circuit for scan (g ate) driver 3 v gl i negative power for scan (gate) driver 4 v gh i positive power for scan (gate) driver 5 stvd i/o vertical start pulse (1) 6 stvu i/o vertical start pulse (1) 7 ckv i shift clock input for scan (gate) driver 8 u/d i up/down scan control input (1) 9 oev i output enable input for scan(gate) driver 10 v com i common electrode driving signal 11 v com i common electrode driving signal 12 l/r i left/right scan control input (1) 13 mod i sequential sampling and simultaneous sampl ing setting (2) 14 oeh i output enable input for data (source) driv er 15 sthl i/o start pulse for horizontal scan (gate) line (1) 16 sthr i/o start pulse for horizontal scan (gate) line (1) 17 cph3 i sampling and shifting clock pulse for dat a (source) driver (2) 18 cph2 i sampling and shifting clock pulse for dat a (source) driver (2) 19 cph1 i sampling and shifting clock pulse for dat a (source) driver 20 dv dd i supply voltage of logic control circuit for data (source) driver 21 dgnd - ground for logic circuit 22 v r i alternated video signal input(red) 23 v g i alternated video signal input(green) 24 v b i alternated video signal input(blue) 25 av dd i supply voltage for analog circuit 26 agnd - ground for analog circuit note (1) selection of scanning mode (please refer to the following table) setting of scan control input in/out state for start pulse scanning direction u/d l/r stvd stvu sthr sthl gnd dv dd output input output input up to down, and from left to right. dv dd gnd input output input output down to up, and from right to left. gnd gnd output input input output up to down, and from right to left. dv dd dv dd input output output input down to up, and from left to right. note (2) mod=h: simultaneous sampling.(please chec k cph2 and cph3 to gnd when mod=h) mod=l : sequential sampling. www.datasheet.in
h a n n sta r di sp l a y c o rp . document title hsd070i651 specification page no. 1 3/26 document no. revision 1.0 the information contained in this document is the e xclusive property of hannstar display corporation. it shall not be disclosed, distributed or reproduced in whole or in part without written permission of hann star display corporation. 5.2 back-light unit cn1 ccfl power source ( bhsr-02vs-1 or equivalent ) / japan solderless terminal mfg co., ltd. mating connector: ( sbht-002t-p0.5 ) / japan solderless terminal mfg co., ltd. terminal no. symbol function 1 vl ccfl power supply (high voltage) 2 gl ccfl power supply (low voltage) www.datasheet.in
h a n n sta r di sp l a y c o rp . document title hsd070i651 specification page no. 1 4/26 document no. revision 1.0 the information contained in this document is the e xclusive property of hannstar display corporation. it shall not be disclosed, distributed or reproduced in whole or in part without written permission of hann star display corporation. 6.0 electrical characteristics 6.1 tft lcd module item symbol min. typ. max. unit note dv dd 3 3.3 5.5 v v gh 14.3 15 15.7 v v gl -10.5 -10 -9.5 v supply voltage av dd 4.5 5 5.5 v v ia 0.4 - av dd -0.4 v vi ac - 3 - v ac component, video signal amplitude (vr,vg,vb) v idc - av dd /2 - v dc component v cac - 4.7 - vp-p ac component vcom v cdc 1.6 1.8 2.0 v dc component, (1) v ih 0.8dv dd - dv dd v (2) input signal voltage v il 0 - 0.2 dv dd v (2) i dd - 127 - ua dv dd =3.3v i add - 7.0 - ma av dd =5v(black) i gh - 70 - ua v gh =15v current of power supply i gl - 65 - ua v gl =-10v note (1): the brightness of lcd panel could be cha nged by adjusting the ac component of v com . note (2): sthl, sthr, oeh, l/r, cph1~cph3, stvd, s tvu, oev, ckv, u/d note (3): b e sure to apply the power voltage as the power sequ ence spec. note (4) : d gnd=agnd=0v,) www.datasheet.in
h a n n sta r di sp l a y c o rp . document title hsd070i651 specification page no. 1 5/26 document no. revision 1.0 the information contained in this document is the e xclusive property of hannstar display corporation. it shall not be disclosed, distributed or reproduced in whole or in part without written permission of hann star display corporation. 6.2 back-light unit the back-light system is an edge-lighting type with 1 ccfl (cold cathode fluorescent lamp) . the characteristics of the lamp is shown in the fol lowing tables. item symbol min. typ. max. unit note lamp current il 3.0 6.0 7.0 ma(rms) (1)(6) lamp voltage vl 496 548 610 v(rms) (6)i l =6.0ma frequency fl 40 50 80 khz (2) operating lamp life time hr 15,000 hour (3) 1000 (4)(5)at 25 o c startup voltage vs 1330 v(rms) (4)(5)at 0 o c note (1) lamp current is measured with current mete r for high frequency as shown below. specified valued are for single lamp. note (2) lamp frequency may produce interference wi th horizontal synchronous frequency and this may cause ripple noi se on the display. therefore lamp frequency shall be kept awa y from the horizontal synchronous frequency and its harmonics as far as possible in order to avoid interference. note (3) lamp life time (hr) can be defined as the time in which it continues to operate under the condition : ta=253 o c, typical il value indicated in the above table and fl=50khz until the brightness b ecomes less than 50%. note (4) ccfl inverter should be able to provide a voltage over specified value (vs) in the above table. lamp units need at l east vs value shown above to ignition. lcd module white(ground) red a inverter ( hiu 766-22pf ) 1 2 www.datasheet.in
h a n n sta r di sp l a y c o rp . document title hsd070i651 specification page no. 1 6/26 document no. revision 1.0 the information contained in this document is the e xclusive property of hannstar display corporation. it shall not be disclosed, distributed or reproduced in whole or in part without written permission of hann star display corporation. note (5) the voltage over specified value (vs) sho uld be applied to the lamp more than 1 second after startup. otherwise, the lamp may not b e turned on. the used lamp current is the lamp typical current. note (6) the output voltage waveform and current w aveform of the inverter must be symmetrical (unsymmetrical ratio is less than 10%). please do not use the inverter which has unsymmetrical voltage and curren t waveform, and spike waveform. the inverter design which can provide the best optical performance, power efficiency, and lamp life should under the fo llowing conditions. a. the asymmetry rate of the inverter waveform shou ld be less than 10%. b. the distortion tae of the waveform should be wit hin 210%. c. the inverter output waveform should be better si milar to the ideal sine wave. asymmetry rate = |i p -i -p | / i rms x 100% distortion rate = i p (or i -p ) / i rms ip i-p www.datasheet.in
h a n n sta r di sp l a y c o rp . document title hsd070i651 specification page no. 1 7/26 document no. revision 1.0 the information contained in this document is the e xclusive property of hannstar display corporation. it shall not be disclosed, distributed or reproduced in whole or in part without written permission of hann star display corporation. 6.3 ac characteristics item symbo l min. typ. max. unit note rising time t r - - 10 ns (1) falling time t f - - 10 ns (1) high and low level pulse duty t cph 100 103 - ns cph1~cph3 cph pulse duty t cwh 40 50 60 cph1~cph3 sth setup time t suh 20 - - ns sthr,sthl sth hold time t hdh 10 - - ns sthr,sthl sth pulse width t sth - 1 - t cph sthr,sthl sth period t h 61.5 63.5 65.5 s sthr,sthl oeh pulse width t oeh - 1.23 - s oeh sample and hold disable time t dis1 - 8.19 - s oev pulse width t oev - 4.77 - s oev ckv pulse width t ckv - 3.91 - s ckv clean enable time t dis2 - 3.90 - s horizontal display timing range t dh - 1440 - t cph /3 stv setup time t suv 200 - - ns stvd,stvu stv hold time t hdv 300 - - ns stvd,stvu stv pulse width t stv - 1 - t h stvd,stvu horizontal line per field t v 256 262 268 t h (2) vertical display start t sv 3 - t h vertical display timing range t dv 234 - t h vcom rising time t rcom - 5 s vcom falling time t fcom - 5 s vcom delay time t dcom - 3 s rgb delay time t drgb * 1 s note (1): for all of the logic signals. note (2): please dont use odd horizontal lines to drive lcd panel for both odd and even filed simultaneously. www.datasheet.in
h a n n sta r di sp l a y c o rp . document title hsd070i651 specification page no. 1 8/26 document no. revision 1.0 the information contained in this document is the e xclusive property of hannstar display corporation. it shall not be disclosed, distributed or reproduced in whole or in part without written permission of hann star display corporation. 6.4 timing diagram of interface signal cph1 oeh vr,vb,vg sthl(r) tr tf t cph t cwh t suh t hdh t suh t sth t hdh t oeh t dis1 sampling clock timing t dh sthl(r) (input) cph1 sthr(l) (output) t h oeh sthl(r) 1 h h sync horizontal display timing range www.datasheet.in
h a n n sta r di sp l a y c o rp . document title hsd070i651 specification page no. 1 9/26 document no. revision 1.0 the information contained in this document is the e xclusive property of hannstar display corporation. it shall not be disclosed, distributed or reproduced in whole or in part without written permission of hann star display corporation. ckv stvd(u ) t stv t suv t hdv t ckv vertic al shift timing 90% oev ckv vcom vr,vg,vb t oev t dis2 t ckv t dcm t f com t r com 10% t drgb v cac v iac v idc v ia blank white white black white black detail horizontal timing vr,vg,vb vcom (odd) vcom (even) stvd(u) v sync h sync t sv vertical timing the first line www.datasheet.in
h a n n sta r di sp l a y c o rp . document title hsd070i651 specification page no. 2 0/26 document no. revision 1.0 the information contained in this document is the e xclusive property of hannstar display corporation. it shall not be disclosed, distributed or reproduced in whole or in part without written permission of hann star display corporation. 6.5 power sequence power sequence: dv dd -> vgl -> vgh note apply the lamp volatge within the lcd operati on range. when the back-light turns on before the lcd operation or the lcd truns off befor e the back-light turns off. the display may momentarily become white. t 10% 90% level define dv dd vgh vgh gnd dv dd vgl vgl gnd power on power off off off video, logic signal www.datasheet.in
h a n n sta r di sp l a y c o rp . document title hsd070i651 specification page no. 2 1/26 document no. revision 1.0 the information contained in this document is the e xclusive property of hannstar display corporation. it shall not be disclosed, distributed or reproduced in whole or in part without written permission of hann star display corporation. 7.0 reliability test items no. item conditions remark 1 high temperature storage ta=+70 o c, 240hrs 2 low temperature storage ta=-20 o c, 240hrs 3 high temperature operation ta=+60 o c, 240hrs 4 low temperature operation ta=-10 o c, 240hrs 5 high temperature and high humidity (operation) ta=+60 o c, 90%rh, 240hrs 6 thermal cycling test (non operation) -20 o c(30min) +70 o c(30min), 200cycles 7 electrostatic discharge 200v,200pf(0 ) 1 time/each terminal 8 vibration 1.random: 1.04grms, 10~500hz, x/y/z, 30min/each direction 2.sweep sine: 1.5g, 5~500hr, x/y/z, 30min/each direction 9 shock 100g,6ms, x, y, z 3 time for each direction jis c7021, a-10 (condition a) 10 vibration (with carton) random: 1.04grms, 10~500hz, x/y/z 45min/each direction fixed: 5hz, 1.5grms, x/y/z 45min/each direction 11 drop (with carton) height: 60cm 1 corner, 3 edges, 6 surfaces jis z0202 note: there are no display function ng issue occur red, all the cosmetic specification is judged before the reliability stress. www.datasheet.in
h a n n sta r di sp l a y c o rp . document title hsd070i651 specification page no. 2 2/26 document no. revision 1.0 the information contained in this document is the e xclusive property of hannstar display corporation. it shall not be disclosed, distributed or reproduced in whole or in part without written permission of hann star display corporation. 8.0 outline dimension 8.1 outline dimension u u nit : mm www.datasheet.in
h a n n sta r di sp l a y c o rp . document title hsd070i651 specification page no. 2 3/26 document no. revision 1.0 the information contained in this document is the e xclusive property of hannstar display corporation. it shall not be disclosed, distributed or reproduced in whole or in part without written permission of hann star display corporation. 9.0 lot mark 9.1 lot mark 10 11 12 13 14 15 code 1,2,3,4,5,6: hannstar internal flow control co de. code 7: production location. code 8: production year. code 9: production month. code 10,11,12,13,14,15: serial number. note (1) production year year 1999 2000 2001 2002 2003 2004 2005 2006 2007 2008 mark 9 0 1 2 3 4 5 6 7 8 note (2) production month month jan. feb. mar. apr. may. jun. jul. aug. sep. oct nov. dec. mark 1 2 3 4 5 6 7 8 9 a b c 9.2 location of lot mark (1) the label is attached to the backside of the lc d module. (2) this is subject to change without prior notice. hsd070i651 - c00 rev: 00 lot mark www.datasheet.in
h a n n sta r di sp l a y c o rp . document title hsd070i651 specification page no. 2 4/26 document no. revision 1.0 the information contained in this document is the e xclusive property of hannstar display corporation. it shall not be disclosed, distributed or reproduced in whole or in part without written permission of hann star display corporation. 6 5 4 2 3 1 10.0 package specification 10.1 packing form (1) package quantity in one carton: 60 pieces. (2) carton size: 464 3 mm 360 3 mm 370 3 mm. (3) for domestic transportation only. 10.2 packing assembly drawings www.datasheet.in
h a n n sta r di sp l a y c o rp . document title hsd070i651 specification page no. 2 5/26 document no. revision 1.0 the information contained in this document is the e xclusive property of hannstar display corporation. it shall not be disclosed, distributed or reproduced in whole or in part without written permission of hann star display corporation. 11.0 general precaution 11.1 use restriction this product is not authorized for use in life supp orting systems, aircraft navigation control systems, military systems and any other applicatio n where performance failure could be life-threatening or otherwise catastrophic. 11.2 disassembling or modification do not disassemble or modify the module. it may da mage sensitive parts inside lcd module, and may cause scratches or dust on the dis play. hannstar does not warrant the module, if customers disassemble or modify the mod ule. 11.3 breakage of lcd panel 11.3.1.if lcd panel is broken and liquid crystal sp ills out, do not ingest or inhale liquid crystal, and do not contact liquid crystal with ski n. 11.3.2. if liquid crystal contacts mouth or eyes, r inse out with water immediately. 11.3.3. if liquid crystal contacts skin or cloths, wash it off immediately with alcohol and rinse thoroughly with water. 11.3.4. handle carefully with chips of glass that m ay cause injury, when the glass is broken. 11.4 electric shock 11.4.1. disconnect power supply before handling lcd module. 11.4.2. do not pull or fold the ccfl cable. 11.4.3. do not touch the parts inside lcd modules a nd the fluorescent lamps connector or cables in order to prevent electric shock. 11.5 absolute maximum ratings and power protection circuit 11.5.1. do not exceed the absolute maximum rating v alues, such as the supply voltage variation, input voltage variation, variation in pa rts parameters, environmental temperature, etc., otherwise lcd module may be dama ged. 11.5.2. please do not leave lcd module in the envir onment of high humidity and high temperature for a long time. 11.5.3. its recommended to employ protection circu it for power supply. 11.6 operation 11.6.1 do not touch, push or rub the polarizer with anything harder than hb pencil lead. 11.6.2 use fingerstalls of soft gloves in order to keep clean display quality, when persons handle the lcd module for incoming inspection or as sembly. 11.6.3 when the surface is dusty, please wipe gentl y with absorbent cotton or other soft material. www.datasheet.in
h a n n sta r di sp l a y c o rp . document title hsd070i651 specification page no. 2 6/26 document no. revision 1.0 the information contained in this document is the e xclusive property of hannstar display corporation. it shall not be disclosed, distributed or reproduced in whole or in part without written permission of hann star display corporation. 11.6.4 wipe off saliva or water drops as soon as po ssible. if saliva or water drops contact with polarizer for a long time, they may causes def ormation or color fading. 11.6.5 when cleaning the adhesives, please use abso rbent cotton wetted with a little petroleum benzine or other adequate solvent. 11.7 mechanism please mount lcd module by using mouting holes arra nged in four corners tightly. 11.8 static electricity 11.8.1 protection film must remove very slowly from the surface of lcd module to prevent from electrostatic occurrence. 11.8.2. because lcd module use cmos-ic on circuit b oard and tft-lcd panel, it is very weak to electrostatic discharge. please be careful with electrostatic discharge. persons who handle the module should be grounded t hrough adequate methods. 11.9 strong light exposure the module shall not be exposed under strong light such as direct sunlight. otherwise, display characteristics may be changed. 11.10 disposal when disposing lcd module, obey the local environm ental regulations. www.datasheet.in

▲Up To Search▲

Price & Availability of HSD070I651-C00

	To Download HSD070I651-C00 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .