 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| user?s manual target devices pd789842 subseries IE-789842-NS-EM1 emulation board document no. u14545ej2v0um00 (2nd edition) date published december 2002 n cp(k) ? printed in japan
user?s manual u14545ej2v0um 2 [memo] user?s manual u14545ej2v0um 3 windows is either a registered trademark or a trademark of microsoft corporation in the united states and/or other countries. pc/at is a trademark of international business machines corporation. the information in this document is current as of september, 2002. the information is subject to change without notice. for actual design-in, refer to the latest publications of nec electronics data sheets or data books, etc., for the most up-to-date specifications of nec electronics products. not all products and/or types are available in every country. please check with an nec electronics sales representative for availability and additional information. no part of this document may be copied or reproduced in any form or by any means without the prior written consent of nec electronics. nec electronics assumes no responsibility for any errors that may appear in this document. nec electronics does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of nec electronics products listed in this document or any other liability arising from the use of such products. no license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of nec electronics or others. descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. the incorporation of these circuits, software and information in the design of a customer's equipment shall be done under the full responsibility of the customer. nec electronics assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. while nec electronics end eavors to enhance the quality, reliability and safety of nec electronics products, customers agree and acknowledge that the p ossibility of defects thereof cannot be eliminated entirely. to minimize risks of damage to property or injury (including death) to persons arising from defects in nec electronics products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment and anti-failure features. nec electronics products are classified into the following three quality grades: "standard", "special" and "specific". the "specific" quality grade applies only to nec electronics products developed based on a customer- designated "quality assurance program" for a specific application. the recommended applications of an nec electronics product depend on its quality grade, as indicated below. customers must check the quality grade of each nec electronics product before using it in a particular application. the quality grade of nec electronics products is "standard" unless otherwise expressly specified in nec electronics data sheets or data books, etc. if customers wish to use nec electronics products in applications not intended by nec electronics, they must contact an nec electronics sales representative in advance to determine nec electronics' willingness to support a given application. (note) ? ? ? ? ? ? m8e 02. 11-1 (1) (2) "nec electronics" as used in this statement means nec electronics corporation and also includes its majority-owned subsidiaries. "nec electronics products" means any product developed or manufactured by or for nec electronics (as defined above). computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots. transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support). aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. "standard": "special": "specific": user ? s manual u14545ej2v0um 4 regional information ? device availability ? ordering information ? product release schedule ? availability of related technical literature ? development environment specifications (for example, specifications for third-party tools and components, host computers, power plugs, ac supply voltages, and so forth) ? network requirements in addition, trademarks, registered trademarks, export restrictions, and other legal issues may also vary from country to country. nec electronics america, inc. (u.s.) santa clara, california tel: 408-588-6000 800-366-9782 fax: 408-588-6130 800-729-9288 nec electronics hong kong ltd. hong kong tel: 2886-9318 fax: 2886-9022/9044 nec electronics hong kong ltd. seoul branch seoul, korea tel: 02-528-0303 fax: 02-528-4411 nec electronics shanghai, ltd. shanghai, p.r. china tel: 021-6841-1138 fax: 021-6841-1137 nec electronics taiwan ltd. taipei, taiwan tel: 02-2719-2377 fax: 02-2719-5951 nec electronics singapore pte. ltd. novena square, singapore tel: 6253-8311 fax: 6250-3583 j02.11 nec electronics (europe) gmbh duesseldorf, germany tel: 0211-65 03 01 fax: 0211-65 03 327 ?sucursal en espa?a madrid, spain tel: 091-504 27 87 fax: 091-504 28 60 v lizy-villacoublay, france tel: 01-30-67 58 00 fax: 01-30-67 58 99 ?succursale fran?aise ?filiale italiana milano, italy tel: 02-66 75 41 fax: 02-66 75 42 99 ?branch the netherlands eindhoven, the netherlands tel: 040-244 58 45 fax: 040-244 45 80 ?tyskland filial taeby, sweden tel: 08-63 80 820 fax: 08-63 80 388 ?united kingdom branch milton keynes, uk tel: 01908-691-133 fax: 01908-670-290 some information contained in this document may vary from country to country. before using any nec electronics product in your application, piease contact the nec electronics office in your country to obtain a list of authorized representatives and distributors. they will verify: user?s manual u14545ej2v0um 5 major revisions in this edition page description throughout ? addition of ie-78k0s-ns-a as supported in-circuit emulator ? addition of np-44gb-tq and np-h44gb-tq as supported emulation probes ? addition of tgb-044sap as supported conversion adapter pp. 12, 13 figure 1-1 system configuration ? modification of supply medium of debugger id78k0s-ns to cd-rom ? modification of the shape of interface cable ? modification of notes 1 to 3 ? addition of table 1-1 correspondence between emulation probe and conversion socket/conversion adapter p. 15 partial modification of table 1-2 basic specifications p. 20 3.2 switch and jumper settings on main unit ? addition of (2) settings on the ie-78k0s-ns-a p. 28 of previous edition deletion of 3.3 low-voltage emulation setting p. 21 addition of 3.3 setting power supply voltage of target interface pp. 22 to 24 3.4.1 overview of clock settings ? change from ?internal clock? in previous edition to ?clock oscillator? ? figure 3-3 external circuits used as system clock oscillator addition of v ss pin in figure of (a) clock oscillator ? figure 3-4 when using clock that is already mounted on emulation board, figure 3-5 when using user-mounted clock change from ?resonator? in previous revision to ?clock oscillator or external clock? on target system ? change from ?clock generator? in previous edition to ?external clock? in figure 3-6 when supplying pulse from target system pp. 24 to 27 3.4.2 system clock settings ? change from ?main system clock? in the previous edition to ?system clock? pp. 34, 35 addition of appendix b notes on designing target system the mark shows major revised points. user?s manual u14545ej2v0um 6 introduction product overview the IE-789842-NS-EM1 is designed to be used with the ie-78k0s-ns or ie-78k0s-ns-a to debug the following target devices that belong to the 78k/0s series of 8-bit single-chip microcontrollers. ? pd789842 subseries: pd789841, 789842, 78f9842 target readers this manual is intended for engineers who will use the IE-789842-NS-EM1 with the ie- 78k0s-ns or ie-78k0s-ns-a to perform system debugging. engineers who use this manual are expected to be thoroughly familiar with the target device?s functions and use methods and to be knowledgeable about debugging. organization when using the IE-789842-NS-EM1, refer to not only this manual (supplied with the ie- 789842-ns-em1) but also the manual that is supplied with the ie-78k0s-ns or ie- 78k0s-ns-a. ie-78k0-ns IE-789842-NS-EM1 user?s manual user?s manual ? basic specifications ? general ? system configuration ? part names ? external interface functions ? installation ? differences between target devices and target interface circuits ie-78k0s-ns-a ? precautions user?s manual ? basic specifications ? system configuration ? external interface functions purpose this manual?s purpose is to explain various debugging functions that can be performed when using the IE-789842-NS-EM1. user?s manual u14545ej2v0um 7 terminology the meanings of certain terms used in this manual are listed below. term meaning emulation device this is a general term that refers to the device in the emulator that is used to emulate the target device. it includes the emulation cpu. emulation cpu this is the cpu block in the emulator that is used to execute user-generated programs. target device this is the device to be emulated. target system this incl udes the target program and the hardware provided by the user. when defined narrowly, it includes only the hardware. ie system this refers to the combination of the in-circuit emulator (ie-78k0s-ns or ie-78k0s-ns-a) and emulation board (IE-789842-NS-EM1). conventions data significance: higher digits on the left and lower digits on the right note : footnote for item marked with note in the text caution : information requiring particular attention remark : supplementary information related documents the related documents (user?s manuals) indicated in this publication may include preliminary versions. however, preliminary versions are not marked as such. document name document number ie-78k0s-ns in-circuit emulator u13549e ie-78k0s-ns-a in-circuit emulator u15207e IE-789842-NS-EM1 emulation board this manual id78k series integrated debugger ver. 2.30 or later operation windows? based u15185e pd789842 subseries u13776e caution the documents listed above are subject to change without notice. be sure to use the latest documents when designing. user?s manual u14545ej2v0um 8 contents chapter 1 general .......................................................................................................... .................11 1.1 system configuration........................................................................................................ ........................12 1.2 hardware configuration ...................................................................................................... ......................14 1.3 basic specifications ........................................................................................................ ..........................15 chapter 2 part names....................................................................................................... ..............16 2.1 parts of main unit.......................................................................................................... .............................17 chapter 3 installation ..................................................................................................... .............18 3.1 connection .................................................................................................................. ...............................19 3.2 switch and jumper settings on main unit..................................................................................... ..........20 3.3 setting power supply voltage of target interface ............................................................................ ......21 3.4 clock settings .............................................................................................................. ..............................22 3.4.1 overview of clock settings ................................................................................................ .............22 3.4.2 system clock settings ..................................................................................................... ...............24 3.5 external trigger............................................................................................................ ..............................28 chapter 4 differences between target device and target interface circuit....29 chapter 5 cautions......................................................................................................... .................32 appendix a emulation probe pin assignment table...........................................................33 appendix b notes on designing target system ....................................................................34 user?s manual u14545ej2v0um 9 list of figures figure no. title page 1-1 system configuration ........................................................................................................ ................................12 1-2 basic hardware configuration................................................................................................ ...........................14 2-1 IE-789842-NS-EM1 part names ................................................................................................. ......................17 3-1 connection of emulation probe............................................................................................... ..........................19 3-2 connecting tm1 and target system power supply voltage....................................................................... ......21 3-3 external circuits used as system clock oscillator ........................................................................... ................22 3-4 when using clock that is already mounted on emulation board ................................................................. ...23 3-5 when using user-mounted clock ............................................................................................... ......................23 3-6 when supplying pulse from target system..................................................................................... .................24 3-7 connections on parts board.................................................................................................. ............................25 3-8 crystal oscillator .......................................................................................................... .....................................26 3-9 pin alignment of crystal oscillator and socket .............................................................................. ...................27 3-10 external trigger input position ............................................................................................ ..............................28 4-1 equivalent circuit of emulation circuit ..................................................................................... .........................31 b-1 distance between ie system and conversion adapter ........................................................................... .........34 b-2 connection conditions of target system (np-44gb-tq) ......................................................................... ........35 b-3 connection conditions of target system (np-h44gb-tq)........................................................................ .......35 user?s manual u14545ej2v0um 10 list of tables table no. title page 1-1 correspondence between emulation probe and conversion socket/conversion adapter.............................. 13 1-2 basic specifications........................................................................................................ .................................. 15 3-1 switch and jumper settings on ie-78k0s-ns................................................................................... ............... 20 3-2 switch and jumper settings on ie-78k0s-ns-a ................................................................................. ............. 20 3-3 setting power supply of target interface .................................................................................... ..................... 21 3-4 system clock settings....................................................................................................... ............................... 24 a-1 np-44gb, np-44gb-tq, np-h44gb-tq pin assignments ............................................................................ .33 b-1 distance between ie system and conversion adapter........................................................................... ......... 34 user?s manual u14545ej2v0um 11 chapter 1 general the IE-789842-NS-EM1 is a development tool for efficient debugging of hardware or software when using one of the following target devices that belong to the 78k/0s series of 8-bit single-chip microcontrollers. this chapter describes the IE-789842-NS-EM1?s system configuration and basic specifications. ? target devices ? pd789842 subseries chapter 1 general user?s manual u14545ej2v0um 12 1.1 system configuration figure 1-1 illustrates the IE-789842-NS-EM1?s system configuration. figure 1-1. system configuration fg cable ie-78k0s-ns or ie-78k0s-ns-a (sold separately) ie-70000-cd-if-a (sold separately) debugger id78k0s-ns (sold separately) device file note 1 (obtain separately) control software host machine pc-9800 series, ibm pc/at ? or compatibles interface board ie-70000-98-if-c (sold separately) interface board ie-70000-pc-if-c (sold separately) interface board ie-70000-pci-if-a (sold separately) or interface cable (ns if cable) in-circuit emulator IE-789842-NS-EM1 (this product) ac adapter ie-70000-mc-ps-b (sold separately) emulation probe note 2 (sold separately) conversion socket/conversion adapter note 3 (sold separately) ns card cable mc card cable interface cable interface card chapter 1 general user ? s manual u14545ej2v0um 13 notes 1. the device file is as follows, in accordance with the subseries. s df789842: pd789842 subseries the device file can be downloaded from the web site of nec electronics (http://www.necel.com/micro/) 2. the emulation probes np-44gb, np-44gb-tq, and np-h44gb-tq are products of naito densei machida mfg. co., ltd. for further information, contact naito densei machida mfg. co., ltd. (tel: +81-45-475-4191) 3. the conversion adapter tgb-044sap is a product of tokyo eletech corporation. for further information, contact daimaru kogyo co., ltd. tokyo electronics department (tel: +81-3-3820-7112) osaka electronics department (tel: +81-6-6244-6672) table 1-1. correspondence between emulation probe and conversion socket/conversion adapter package emulation probe conversion socket/conversion adapter np-44gb (probe length: 200 mm) ev-9200g-44 np-44gb-tq (probe length: 200 mm) 44-pin plastic qfp (gb type) np-h44gb-tq (probe length: 400 mm) tgb-044sap chapter 1 general user ? s manual u14545ej2v0um 14 1.2 hardware configuration figure 1-2 shows the IE-789842-NS-EM1 ? s position in the basic hardware configuration. figure 1-2. basic hardware configuration ie-78k0s-ns or ie-78k0s-ns-a IE-789842-NS-EM1 emulation probe (sold separately) dedicated bus interface ie system host machine interface board (sold separately) 78k0s main board (sold separately) emulation board (this product) interface card (sold separately) chapter 1 general user?s manual u14545ej2v0um 15 1.3 basic specifications the basic specifications of the IE-789842-NS-EM1 are listed in table 1-2. table 1-2. basic specifications parameter description target device pd789842 subseries system clock 8.38 mhz system clock supply external: input via an emulation probe from the target system internal: mounted on the emulation board (8.38 mhz), or mounted on the parts board by the user target interface voltage v dd = 4.0 to 5.5 v (same as that of target device) operates on internal power supply (5 v) when target system is not c onnected user?s manual u14545ej2v0um 16 chapter 2 part names this chapter introduces the parts of the IE-789842-NS-EM1 main unit. the packing box contains the emulation board (IE-789842-NS-EM1), packing list, user?s manual, and guarantee card. if there are any missing or damaged items, please contact an nec electronics sales representative. fill out and return the guarantee card that comes with the main unit. chapter 2 part names user?s manual u14545ej2v0um 17 2.1 parts of main unit figure 2-1 shows the part names of the IE-789842-NS-EM1. figure 2-1. IE-789842-NS-EM1 part names gnd lowvolt extout extin led1 probe connector cn1 44gb system clock x1 44gb cn1 IE-789842-NS-EM1 x1 tm1 user?s manual u14545ej2v0um 18 chapter 3 installation this chapter describes methods for connecting the IE-789842-NS-EM1 to the ie-78k0s-ns or ie-78k0s-ns-a, emulation probe, etc. mode setting methods are also described. caution connecting or removing components to or from the target system, or making switch or other setting changes must be carried out after the power supply to both the ie system and the target system has been switched off. chapter 3 installation user?s manual u14545ej2v0um 19 3.1 connection (1) connection with ie-78k0s-ns or ie-78k0s-ns-a main unit see the ie-78k0s-ns user?s manual (u13549e) for a description of how to connect the IE-789842-NS-EM1 to the ie-78k0s-ns note . note when using the ie-78k0s-ns-a, see the ie-78k0s-ns-a user?s manual (u15207e) . (2) connection with emulation probe see the ie-78k0s-ns user?s manual (u13549e) for a description of how to connect an emulation probe to the IE-789842-NS-EM1 note . on this board, connect the emulation probe to cn1. note when using the ie-78k0s-ns-a, see the ie-78k0s-ns-a user?s manual (u15207e) . caution incorrect connection may damage the ie system. be sure to read the emulation probe?s user?s manual for a detailed description of the connection method. figure 3-1. connection of emulation probe main board of ie-78k0s-ns (sold separately) or ie-78k0s-ns-a (sold separately) IE-789842-NS-EM1 cn1 44gb emulation probe (sold separately) chapter 3 installation user ? s manual u14545ej2v0um 20 3.2 switch and jumper settings on main unit (1) settings on the ie-78k0s-ns when using the IE-789842-NS-EM1, set the switches and jumpers on the ie-78k0s-ns as shown in table 3-1. for details of these switch and jumper settings, refer to the ie-78k0s-ns user?s manual (u13549e) . table 3-1. switch and jumper settings on ie-78k0s-ns sw1 sw3 sw4 jp1 jp4 setting off all switches on (fixed) all switches on (fixed) 2 and 3 shorted 1 and 2 shorted caution incorrect connection may damage the IE-789842-NS-EM1. (2) settings on the ie-78k0s-ns-a when using the IE-789842-NS-EM1, set the switches and jumpers on the ie-78k0s-ns-a as shown in table 3- 2. for details of these switch and jumper settings, refer to the ie-78k0s-ns-a user?s manual (u15207e) . table 3-2. switch and jumper settings on ie-78k0s-ns-a sw1 jp1 jp3 setting off 1 and 2 shorted (fixed) shorted (fixed) caution incorrect connection may damage the IE-789842-NS-EM1. chapter 3 installation user ? s manual u14545ej2v0um 21 3.3 setting power supply voltage of target interface in the ie system, emulation is possible with a voltage of the same level as the power supply voltage of the target system. when the target system is not connected, the ie system automatically operates with the emulator ? s internal power supply (5 v). when debugging with a voltage that is the same level as that of the target system, supply the same voltage as that of the target system to the tm1 terminal pin of the IE-789842-NS-EM1 (the same applies when the voltage is 5 v). set the target voltage to between 4.0 and 5.0 v. for how to select the operating power supply, refer to the id78k series ver.2.30 or later operation windows- based user?s manual (u15185e) . ? maximum current consumption of tm1 4.0 to 5.0 v: approximately 125 ma table 3-3. setting power supply of target interface integrated debugger (id78k0s-ns) power supply of target interface (lv cc ) operating power supply selection when connecting target system 4.0 to 5.0 v target when not connecting target system 5 v internal figure 3-2. connecting tm1 and target system power supply voltage cn1 emulation lowvolt v dd gnd gnd tm1 led1 IE-789842-NS-EM1 x1 target system power supply voltage emulation probe target system caution before connecting tm1 on the board and the target system power supply voltage, turn off the power to the ie-78k0s-ns or ie-78k0s-ns-a. remark the v dd pin on the target system is exclusively used to control led1, which monitors whether the power supply of the target system is connected in the IE-789842-NS-EM1. chapter 3 installation user ? s manual u14545ej2v0um 22 3.4 clock settings 3.4.1 overview of clock settings the system clock to be used during debugging can be selected from (1) to (3) below. (1) clock that is already mounted on emulation board (2) clock that is mounted by user (3) pulse input from target system if the target system includes a clock oscillator, select either (1) clock that is already mounted on emulation board or (2) clock that is mounted by user . for the clock oscillator, a resonator is connected to the target device and the target device ? s internal oscillator is used. an example of the external circuit is shown in part (a) of figure 3-3. during emulation, the oscillator that is mounted on the target system is not used. instead, the clock that is mounted on the emulation board installed in the ie-78k0s-ns or ie-78k0s-ns-a is used. if the target system includes an external clock, select either (1) clock that is already mounted on emulation board , (2) clock that is mounted by user , or (3) pulse input from target system . for the external clock, a clock signal is supplied from outside of the target device and the target device ? s internal oscillator is not used. an example of the external circuit is shown in part (b) of figure 3-3. caution the ie system will be hung-up if the main system clock is not supplied normally. moreover, be sure to input a rectangular wave as the pulse from the target system. there is no need to supply a clock to the x2 pin. also, even if a crystal resonator is connected directly to x1, the target device will not operate. figure 3-3. external circuits used as system clock oscillator (a) clock oscillator (b) external clock x1 crystal or ceramic resonator v ss external clock x2 x1 x2 target device target device chapter 3 installation user?s manual u14545ej2v0um 23 (1) clock that is already mounted on emulation board the crystal oscillator mounted on the IE-789842-NS-EM1 can be used. a crystal oscillator (x1) is already mounted on the emulation board. its frequency is 8.38 mhz. figure 3-4. when using clock that is already mounted on emulation board ie-78k0s-ns or ie-78k0s-ns-a IE-789842-NS-EM1 mounted oscillator (used) emulation probe target system clock oscillator or external clock (not used) x1 remark the clock that is supplied by the oscillator of the IE-789842-NS-EM1 (encircled in the figure) is used. (2) clock that is mounted by user the user can mount any clock supported by the set specifications on the IE-789842-NS-EM1. this feature is effective when debugging at a different frequency than the clock already mounted. remove the crystal oscillator (x1) that is already mounted on the emulation board, and mount the parts board on which the resonator to be used is mounted or mount the oscillator to be used. figure 3-5. when using user-mounted clock ie-78k0s-ns or ie-78k0s-ns-a IE-789842-NS-EM1 parts board + resonator or oscillator (used) emulation probe target system clock oscillator or external clock (not used) x1 remark the clock that is supplied by the resonator of the IE-789842-NS-EM1 (encircled in the figure) or the oscillator is used. chapter 3 installation user ? s manual u14545ej2v0um 24 (3) pulse input from target system an external clock on the target system can be used via an emulation probe. figure 3-6. when supplying pulse from target system ie-78k0s-ns or ie-78k0s-ns-a IE-789842-NS-EM1 emulation probe target system external clock (used) mounted oscillator (not used) x1 remark the pulse that is supplied by the external clock on the target system (encircled in the figure) or the oscillator is used. 3.4.2 system clock settings table 3-4 shows the settings of the IE-789842-NS-EM1 when the system clocks in (1) to (3) are used. table 3-4. system clock settings IE-789842-NS-EM1 frequency of system clock x1 socket cpu clock source selection (id78k0s-ns) (1) when using clock that is already mounted on emulation board 8.38 mhz oscillator (2) when using clock mounted by user oscillator configured by user internal (3) when inputting pulse from target system other than 8.38 mhz oscillator (not used) external caution when inputting a pulse from the target system, open the configuration dialog box when starting the integrated debugger (id78k0s-ns) and select ?external? in the area (clock) for selecting the cpu?s clock source (this selects the user?s clock). remark the factory settings of the IE-789842-NS-EM1 are those listed above under ? when using clock that is already mounted on emulation board ? . (1) when using clock that is already mounted on emulation board when the IE-789842-NS-EM1 is shipped, an 8.38 mhz crystal oscillator is already mounted in the ie-789842- ns-em1 ? s x1 socket. when using the factory-set mode settings, there is no need to make any other hardware settings. when starting the integrated debugger (id78k0s-ns), open the configuration dialog box and select ? internal ? in the area (clock) for selecting the cpu ? s clock source (this selects the emulator ? s internal clock). chapter 3 installation user ? s manual u14545ej2v0um 25 (2) when using clock mounted by user perform the settings described under either (a) or (b), depending on the type of clock to be used. when starting the integrated debugger (id78k0s-ns), open the configuration dialog box and select ? internal ? in the area (clock) for selecting the cpu ? s clock source (this selects the emulator ? s internal clock). (a) when using a ceramic resonator or crystal resonator ? items to be prepared ? parts board ? capacitor ca ? ceramic resonator or crystal resonator ? capacitor cb ? resistor rx ? solder kit chapter 3 installation user ? s manual u14545ej2v0um 26 <2> prepare the IE-789842-NS-EM1. <3> remove the crystal oscillator that is mounted in the IE-789842-NS-EM1 ? s x1 socket. <4> connect the parts board (from <1> above) to the x1 socket from which the crystal oscillator was removed. check the pin 1 mark to make sure the board is mounted in the correct direction. <5> make sure that the parts board is wired as shown in figure 3-7 above. <6> install the IE-789842-NS-EM1 in the ie-78k0s-ns or ie-78k0s-ns-a. the above steps configure the following circuit and enable supply of the clock from the mounted resonator to the emulation device. (b) when using a crystal oscillator ? items to be prepared ? crystal oscillator (see pinouts shown in figure 3-8) figure 3-8. crystal oscillator chapter 3 installation user ? s manual u14545ej2v0um 27 figure 3-9. pin alignment of crystal oscillator and socket crystal oscillator pin name socket pin no. nc 1 gnd 7 clock out 8 v cc 14 <4> install the IE-789842-NS-EM1 in the ie-78k0s-ns or ie-78k0s-ns-a. (3) when inputting pulse from target system short pins 6 and 8 of the x1 socket. when starting the integrated debugger (id78k0s-ns), open the configuration dialog box and select ? external ? in the area (clock) for selecting the cpu ? s clock source (this selects the user ? s clock). 14 13 12 11 10 9 8 v cc clock out gnd nc crystal oscillator socket 1 2 3 4 5 6 7 chapter 3 installation user ? s manual u14545ej2v0um 28 3.5 external trigger to set an external trigger, connect the IE-789842-NS-EM1 ? s check pins extout and extin as shown below. see the ie-78k0s-ns user?s manual (u13549e) or ie-78k0s-ns-a user?s manual (u15207e) for pin characteristics. for the use methods, see the id78k series ver.2.30 or later operation windows based user?s manual (u15185e) . (1) extout the extout pin on the IE-789842-NS-EM1 outputs a low level for 1.3 s when a break event occurs. caution connect a pull-up resistor on the target system because this is an open drain output. (2) extin an event signal can be input from the extin pin on the IE-789842-NS-EM1. input a high-level pulse signal for 2 cpu operation clocks or more. figure 3-10. external trigger input position extout tm1 extin 44gb cn1 led1 IE-789842-NS-EM1 x1 external trigger user?s manual u14545ej2v0um 29 chapter 4 differences between target device and target interface circuit this chapter describes differences between the target device?s signal lines and the signal lines of the target interface circuit of the ie system. the target interface circuit of the ie system realizes emulation via an emulation circuit configured by an emulation cpu, ttl, cmos-ic, and other components. the electrical characteristics are different from those of the target device because a protector and other circuits are provided. (1) signals input to or output from the emulation cpu (2) signals input from the target system via a gate (3) analog signals (4) other signals the IE-789842-NS-EM1?s circuit is used as follows for signals listed in (1) to (4) above. (1) signals input to or output from the emulation cpu the following signals perform the same operations as in the pd789841, 789842, and 78f9842. however, a 1 m ? pull-down resistor and 100 ? resistor are inserted in series. ? signals related to port 0 ? signals related to port 1 ? signals related to port 2 ? signals related to 10-bit inverter control timer (to70 to to75) (2) signals input from the target system via a gate since the following signals are input via a gate, their timing shows a delay compared to the pd789841, 789842, and 78f9842. their ac characteristics and dc characteristics are therefore different from the pd789841, 789842, and 78f9842 making it necessary to observe a stricter timing design than in the pd789841, 789842, and 78f9842. ? reset signal ? signals related to clock input from all the signals input from the target system, the reset signal and signals related to clock input are input to the emulation cpu via a logic ic. the dc characteristics are therefore different from the pd789841, 789842, and 78f9842. chapter 4 differences between target device and target interface circuit user?s manual u14545ej2v0um 30 (3) analog signals because the following signals input/output analog signals, special processing is not performed in the ie-789842- ns-em1. ? av dd pin ? port 6 (4) other signals ? v dd pin when the emulation cpu is operating at 5 v, its power is supplied from the IE-789842-NS-EM1, but when operating at low voltage, its power is supplied from the low-voltage pin (tp1). the v dd pin of the target system is only used to control the led (tv cc ) in the IE-789842-NS-EM1 that monitors the input of the target system's power supply. ? v ss and av ss pins the v ss and av ss pins are connected to gnd in the IE-789842-NS-EM1 ? test/v pp pin the test/v pp pin is not used in the IE-789842-NS-EM1. ? x2 pin the x2 pin is not used in the IE-789842-NS-EM1. chapter 4 differences between target device and target interface circuit user?s manual u14545ej2v0um 31 figure 4-1. equivalent circuit of emulation circuit port 0 port 1 port 2 to70 to to75 port 0 port 1 port 2 to70 to to75 reset x1 av dd port 6 av dd port 6 x1 reset 100 ? 4.7 k ? lv cc lv cc hc4066 hc157 pd789009 x1 hsk120 hsk120 power supply detection g6h-2f (relay) filter 100 ? 1 m ? pc393 test/v pp test/v pp x2 v ss av ss v dd open open lv cc + 22 f IE-789842-NS-EM1 side probe side pd789009 + ? user?s manual u14545ej2v0um00 32 chapter 5 cautions this chapter describes points that require special attention when using the IE-789842-NS-EM1. the target device and the emulation function of the IE-789842-NS-EM1 differ with regard to the following. (1) emulation of an rc oscillator is not possible with the IE-789842-NS-EM1. only those functions specified by the clock settings in 3.4 clock settings can be emulated. (2) pin handling is not performed for the port pins on the emulation board. consequently, an undefined value will be read out if an attempt is made to read the value of a port in input mode when an emulation probe is not connected. (3) emulation of the low voltage circuit (lvi) is possible with the IE-789842-NS-EM1. note, however, that the operation-guaranteed voltage is the same as that of the target device (4.0 to 5.5 v); that is, operation is not guaranteed if a voltage lower than this is applied. user?s manual u14545ej2v0um 33 appendix a emulation probe pin assignment table table a-1. np-44gb, np-44gb-tq, np-h44gb-tq pin assignments emulation probe cn1 pin no. emulation probe cn1 pin no. 1 104 23 18 2 103 24 17 3 100 25 22 4992621 5942728 6932827 7302992 8293091 9243198 10 23 32 97 11 20 33 102 12 47 34 73 13 48 35 72 14 51 36 69 15 52 37 70 16 57 38 63 17 58 39 64 18 59 40 61 19 60 41 62 20 55 42 65 21 56 43 66 22 49 44 71 remarks 1. np-44gb, np-44gb-tq, and np-h44gb-tq are products of naito densei machida mfg. co., ltd. 2. the numbers in the ?emulation probe? column indicate the corresponding pin number on the emulation probe tip. user?s manual u14545ej2v0um 34 appendix b notes on designing target system the following shows the conditions when connecting the emulation probe and converstion adapter. consider the shape of the components to be mounted on the target system and follow the configurations below when designing the system. among the products described in this appendix, np-44gb-tq and np-h44gb-tq are products of naito densei machida mfg. co., ltd. and tgb-044sap is a product of tokyo eletech corporation. table b-1. distance between ie system and conversion adapter emulation probe conversion adapter distance between ie system and conversion adapter np-44gb-tq 170 mm np-h44gb-tq tgb-044sap 370 mm figure b-1. distance between ie system and conversion adapter 170 mm note in-circuit emulator ie-78k0s-ns or ie-78k0s-ns-a emulation board IE-789842-NS-EM1 conversion adapter: tgb-044sap target system emulation probe np-44gb-tq np-h44gb-tq note the above distance shows when the np-44gb-tq is used. when the np-h44gb-tq is used, the distance is 370 mm. appendix b notes on designing target system user ? s manual u14545ej2v0um 35 figure b-2. connection conditions of target system (np-44gb-tq) emulation probe np-44gb-tq 24.8 mm 25 mm 40 mm 34 mm target system conversion adapter tgb-044sap 16.65 mm pin 1 10.95 mm emulation board IE-789842-NS-EM1 16.65 mm figure b-3. connection conditions of target system (np-h44gb-tq) emulation probe np-h44gb-tq emulation board IE-789842-NS-EM1 23 mm 42 mm 45 mm target system 10.95 mm conversion adapter tgb-044sap 10 mm 16.65 mm pin 1 16.65 mm |
Price & Availability of IE-789842-NS-EM1
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |