 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Transys Electronics LIMITED PNP SILICON PLANAR EPITAXIAL TRANSISTORS PN4354 PN4355 PN4356 TO-92 Plastic Package E BC General Purpose Amplifiers DESCRIPTION Collector Emitter Voltage Collector Base Voltage Emitter Base Voltage Collector Current - Continuous Power Dissipation@Ta=25C Power Dissipation@ Tc=25C Operating And Storage Junction Temperature Range ELECTRICAL CHARACTERISTICS (Ta=25C Unless Otherwise Specified) DESCRIPTION SYMBOL TEST CONDITION 4354 Collector Emitter Voltage Collector Base Voltage Emitter Base Voltage Collector-Cut off Current VCEO(sus)* VCBO VEBO ICBO IC=10mA,IB=0 (pulsed) IC=10uA,IE=0 IE=10uA,IC=0 VCB=50V, IE = 0 VcB=50V, IE = 0, Ta =75C VBE =4V,IC= 0 >60 >60 SYMBOL VCEO VCBO VEBO IC PD PD Tj, Tstg 4354 60 60 4355 60 60 5 500 625 1.0 -55 to +150 4356 80 80 UNITS V V V mA mW mW C 4355 >60 >60 >5 4356 >80 >80 <50 <5 <100 UNITS V V V nA uA nA Emitter Cut off Current DC Current Gain IEBO hFE * VCE=10V,IC=100uA VCE=10V,IC=1mA VCE=10V,IC=10mA VCE=10V,IC=100mA VCE=10V,IC=500mA >25 >40 50-500 >40 >30 >60 >75 100-400 >75 >75 >25 >40 50-250 >40 >30 Commom Emitter Small Signal Current Gain l hfe l IC=50mA, VCE=10V f=100MHz 1.0-5.0 1.0 - 1.5 1.0 - 5.0 Collector Emitter Sat Voltage VCE(sat) * IC=150mA,IB=15mA IC=500mA,IB=50mA IC=1A,IB=100mA PN4355 <0.15 <0.5 <0.15 <0.5 <1.0 <0.15 <0.5 V V V PNP SILICON PLANAR EPITAXIAL TRANSISTORS PN4354 PN4355 PN4356 TO-92 Plastic Package E BC ELECTRICAL CHARACTERISTICS (Ta=25C Unless Otherwise Specified) DESCRIPTION SYMBOL TEST CONDITION 4354 VBE(sat)* IC=150mA,IB=15mA Base Emitter Sat Voltage <0.9 IC=500mA,IB=50mA <1.1 IC=1A,IB=100mA PN4355 VBE(on)* Base Emitter On Voltage PN4355 SMALL-SIGNAL DYNAMIC CHARACTERISTICS Ccb Collector to Base Capacitance Ceb Emitter to Base Capacitance ton Turn On Time toff Turn off Time IE=0, VCB=10V, f=1.0MHZ IC=0, VEB=0.5V, f=1.0MHZ IC =500mA,IB1 =50mA, VCC =30V IC =500mA,IB1=IB2 =50mA, VCC =30V <400 <30 <110 <100 SYMBOL TEST CONDITION 4354 IC=500mA,VCE=0.5V IC=1A,VCE=1V <1.1 4355 <0.9 <1.1 <1.2 <1.1 <1.2 4356 <0.9 <1.1 UNITS V V V V V <1.1 4355 4356 UNITS <30 <110 <100 <30 <110 <100 PF PF PF <400 <400 ns Noise Figure NF VCE =10V,IC=100uA RS=1K,f=1kHZ, <3.0 <3.0 <3.0 dB BW = 1HZ *Pulse Condition: = 300us, Duty Cycle = 1%. PN4354 PN4355 PN4356 TO-92 Plastic Package TO-92 Plastic Package B TO-92 Transistors on Tape and Ammo Pack Ammo Pack Style MECHANICAL DATA T P h A H1 W2 L Wo W1 W Adhesive Tape on Top Side (p) D FEE Carrier Strip 8.2" A h A1 LABEL FLAT SIDE 321 H0 t1 t F1 F P2 Po F2 Do 13" K 1.7 7" Flat Side of Transistor and Adhesive Tape Visible 2000 pcs./Ammo Pack D D G 3 E 2 1 All dimensions in mm unless specified otherwise ITEM BODY WIDTH BODY HEIGHT BODY THICKNESS PITCH OF COMPONENT FEED HOLE PITCH FEED HOLE CENTRE TO COMPONENT CENTRE DISTANCE BETWEEN OUTER LEADS COMPONENT ALIGNMENT TAPE WIDTH HOLD-DOWN TAPE WIDTH HOLE POSITION HOLD-DOWN TAPE POSITION LEAD WIRE CLINCH HEIGHT COMPONENT HEIGHT LENGTH OF SNIPPED LEADS FEED HOLE DIAMETER TOTAL TAPE THICKNESS LEAD - TO - LEAD DISTANCEF1, CLINCH HEIGHT PULL - OUT FORCE SYMBOL A1 A T P Po P2 F h W Wo W1 W2 Ho H1 L Do t F2 H2 (P) SPECIFICATION REMARKS MIN. NOM. MAX. TOL . 4.0 4.8 5.2 4.8 4.2 3.9 12.7 1 12.7 0.3 CUMULATIVE PITCH ERROR 1.0 mm/20 PITCH 6.35 0.4 TO BE MEASURED AT BOTTOM OF CLINCH +0.6 5.08 -0.2 1 0 AT TOP OF BODY 18 0.5 6 0.2 9 +0.7 -0.5 0.5 0.2 16 0.5 23.25 11.0 4 0.2 1.2 t1 0.3 - 0.6 2.54 +0.4 -0.1 3 6N AA SEC AA F F DIM A B C D E F G H K MIN. MAX. 321 PIN CONFIGURATION 1. COLLECTOR 2. BASE 3. EMITTER All diminsions in mm. 4.32 5.33 4.45 5.20 3.18 4.19 0.41 0.55 0.35 0.50 5 DEG 1.14 1.14 12.70 1.40 1.53 -- H C NOTES 1. MAXIMUM ALIGNMENT DEVIATION BETWEEN LEADS NOT TO BE GREATER THAN 0.2 mm. 2. MAXIMUM NON-CUMULATIVE VARIATION BETWEEN TAPE FEED HOLES SHALL NOT EXCEED 1 mm IN 20 PITCHES. 3. HOLDDOWN TAPE NOT TO EXCEED BEYOND THE EDGE(S) OF CARRIER TAPE AND THERE SHALL BE NO EXPOSURE OF ADHESIVE. 4. NO MORE THAN 3 CONSECUTIVE MISSING COMPONENTS ARE PERMITTED. 5. A TAPE TRAILER, HAVING AT LEAST THREE FEED HOLES ARE REQUIRED AFTER THE LAST COMPONENT. 6. SPLICES SHALL NOT INTERFERE WITH THE SPROCKET FEED HOLES. Packing Detail PACKAGE TO-92 Bulk TO-92 T&A STANDARD PACK Details Net Weight/Qty 1K/polybag 200 gm/1K pcs 2K/ammo box 645 gm/2K pcs INNER CARTON BOX Size Qty 3" x 7.5" x 7.5" 5.0K 12.5" x 8" x 1.8" 2.0K OUTER CARTON BOX Size Qty Gr Wt 17" x 15" x 13.5" 80.0K 23 kgs 17" x 15" x 13.5" 32.0K 12.5 kgs |
Price & Availability of PN4355
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |