View ADUM6400_4501229.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Quad-Channel Isolators with Integrated DC-to-DC Converter
ADUM6400/ADuM6401/ADuM6402/ADuM6403/ADuM6404
FEATURES
isoPower integrated, isolated dc-to-dc converter Regulated 3.3 V or 5 V output Up to 500 mW output power Quad dc-to-25 Mbps (NRZ) signal isolation channels Schmitt trigger inputs 16-lead SOIC package with 7.6 mm creepage High temperature operation: 105C High common-mode transient immunity: >25 kV/s Safety and regulatory approvals (pending) UL recognition 5000 V rms for 1 minute per UL1577 CSA Component Acceptance Notice #5A IEC 60950-1: 600 V rms (reinforced) IEC 60601-1: 250 V rms (reinforced) VDE certificate of conformity DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 VIORM = 560 V peak
FUNCTIONAL BLOCK DIAGRAMS
VDD1 1 GND1 2 VIA/VOA 3 VIB/VOB 4 VIC/VOC 5 VID/VOD 6 VDDL 7 GND1 8 4-CHANNEL iCOUPLER CORE OSC RECT REG
16 VISO 15 GNDISO 14 VIA/VOA 13 VIB/VOB 12 VIC/VOC 11 VID/VOD 10 VSEL 9
ADUM6400/ADuM6401/ ADuM6402/ADuM6403/ ADuM6404
GNDISO
Figure 1. ADuM640x Block Diagram
VIA
3 14 13
VOA
4
VIB VIC VID
VOB VOC VOD
08141-002
ADUM6400
5 6 12 11
Figure 2. ADUM6400
VIA VIB VIC VOD
3 4 14 13
APPLICATIONS
RS-232/RS-422/RS-485 transceivers Medical isolation AC/dc power supply startup bias and gate drives Isolated sensor interface
VOA VOB VOC VID
08141-003
ADuM6401
5 6 12 11
Figure 3. ADuM6401
VIA VIB VOC VOD
3 4 14 13
GENERAL DESCRIPTION
The ADuM640x1 devices are quad-channel digital isolators with isoPower(R), an integrated, isolated dc-to-dc converter. Based on the Analog Devices, Inc., iCoupler(R) technology, the dc-to-dc converter provides up to 500 mW of regulated, isolated power at either 5.0 V or 3.3 V from a 5.0 V input supply, or 3.3 V from a 3.3 V supply at the power levels shown in Table 1. This eliminates the need for a separate, isolated dc-to-dc converter in low power, isolated designs. The iCoupler chip scale transformer technology is used to isolate the logic signals and for the magnetic components of the dc-to-dc converter. The result is a small form factor, total isolation solution. The ADuM640x isolators provide four independent isolation channels in a variety of channel configurations and data rates (see the Ordering Guide for more information). isoPower uses high frequency switching elements to transfer power through its transformer. Special care must be taken during printed circuit board (PCB) layout to meet emissions standards. Refer to the AN-0971 application note for board layout recommendations at www.analog.com.
1
VOA VOB VIC VID
08141-004
ADuM6402
5 6 12 11
Figure 4. ADuM6402
VIA VOB VOC VOD
3 4 14 13
VOA VIB VIC VID
08141-005
ADuM6403
5 6 12 11
Figure 5. ADuM6403
VOA VOB VOC VOD VIA
3 4 14 13
VIB VIC
ADuM6404
5 6 12 11
VID
Figure 6. ADuM6404
Table 1. Power Levels
Input Voltage (V) 5 5 3.3 Output Voltage (V) 5 3.3 3.3 Output Power (mW) 500 330 200
Protected by U.S. Patents 5,952,849; 6,873,065; 6,903,578; and 7,075,329. Other patents are pending.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 (c)2009 Analog Devices, Inc. All rights reserved.
08141-006
08141-001
ADUM6400/ADuM6401/ADuM6402/ADuM6403/ADuM6404 TABLE OF CONTENTS
Features .............................................................................................. 1 Applications ....................................................................................... 1 General Description ......................................................................... 1 Functional Block Diagrams ............................................................. 1 Revision History ............................................................................... 2 Specifications..................................................................................... 3 Electrical Characteristics--5 V Primary Input Supply/5 V Secondary Isolated Supply .......................................................... 3 Electrical Characteristics--3.3 V Primary Input Supply/3.3 V Secondary Isolated Supply .......................................................... 5 Electrical Characteristics--5 V Primary Input Supply/3.3 V Secondary Isolated Supply .......................................................... 6 Package Characteristics ............................................................... 8 Regulatory Approvals................................................................... 8 Insulation and Safety-Related Specifications ............................ 8 DIN V VDE V 0884-10 (VDE V 0884-10) Insulation Characteristics .............................................................................. 9 Recommended Operating Conditions ...................................... 9 Absolute Maximum Ratings.......................................................... 10 ESD Caution ................................................................................ 10 Pin Configurations and Function Descriptions ......................... 11 Truth Table .................................................................................. 15 Typical Performance Characteristics ........................................... 16 Terminology .................................................................................... 18 Applications Information .............................................................. 19 Theory of Operation .................................................................. 19 Printed Circuit Board (PCB) Layout ....................................... 19 Thermal Analysis ....................................................................... 19 Propagation Delay-Related Parameters ................................... 20 EMI Considerations ................................................................... 20 DC Correctness and Magnetic Field Immunity........................... 20 Power Consumption .................................................................. 21 Power Considerations ................................................................ 21 Insulation Lifetime ..................................................................... 22 Outline Dimensions ....................................................................... 23 Ordering Guide .......................................................................... 23
REVISION HISTORY
5/09--Revision 0: Initial Version
Rev. 0 | Page 2 of 24
ADUM6400/ADuM6401/ADuM6402/ADuM6403/ADuM6404 SPECIFICATIONS
ELECTRICAL CHARACTERISTICS--5 V PRIMARY INPUT SUPPLY/5 V SECONDARY ISOLATED SUPPLY
All typical specifications are at TA = 25C, VDD1 = VSEL = VISO = 5 V. Minimum/maximum specifications apply over the entire recommended operation range which is 4.5 V VDD1, VSEL, VISO 5.5 V; and -40C TA +105C, unless otherwise noted. Switching specifications are tested with CL = 15 pF and CMOS signal levels, unless otherwise noted. Table 2. DC-to-DC Converter Static Specifications
Parameter DC-TO-DC CONVERTER SUPPLY Setpoint Line Regulation Load Regulation Output Ripple Output Noise Switching Frequency PW Modulation Frequency Output Supply Efficiency at IISO (MAX) IDD1, No VISO Load IDD1, Full VISO Load Symbol VISO VISO (LINE) VISO (LOAD) VISO (RIP) VISO (NOISE) fOSC fPWM IISO (MAX) IDD1 (Q) IDD1 (MAX) Min 4.7 Typ 5.0 1 1 75 200 180 625 34 19 290 Max 5.4 5 Unit V mV/V % mV p-p mV p-p MHz kHz mA % mA mA Test Conditions IISO = 0 mA IISO = 50 mA, VDD1 = 4.5 V to 5.5 V IISO = 10 mA to 90 mA 20 MHz bandwidth, CBO = 0.1 F||10 F, IISO = 90 mA CBO = 0.1 F||10 F, IISO = 90 mA
100 30
VISO > 4.5 V IISO = 100 mA
Table 3. DC-to-DC Converter Dynamic Specifications
Parameter SUPPLY CURRENT ADUM6400 ADuM6401 ADuM6402 ADuM6403 ADuM6404 Symbol IDD1 IISO (LOAD) IDD1 IISO (LOAD) IDD1 IISO (LOAD) IDD1 IISO (LOAD) IDD1 IISO (LOAD) 2 Mbps--A Grade, B Grade, C Grade Min Typ Max 19 100 19 100 19 100 19 100 19 100 25 Mbps--C Grade Min Typ Max 64 89 68 87 71 85 75 83 78 81 Unit mA mA mA mA mA mA mA mA mA mA Test Conditions No VISO load No VISO load No VISO load No VISO load No VISO load
Rev. 0 | Page 3 of 24
ADUM6400/ADuM6401/ADuM6402/ADuM6403/ADuM6404
Table 4. Switching Specifications
Parameter SWITCHING SPECIFICATIONS Data Rate Propagation Delay Pulse Width Distortion Change vs. Temperature Pulse Width Propagation Delay Skew Channel Matching Codirectional 1 Opposing Directional 2
1
7Codirectional
Symbol
Min
A Grade Typ Max 1 100 40
Min
C Grade Typ Max 25 60 6
Unit Mbps ns ns ps/C ns ns ns ns
Test Conditions Within PWD limit 50% input to 50% output |tPLH - tPHL| Within PWD limit Between any two units
tPHL, tPLH PWD PW tPSK tPSKCD tPSKOD 1000
55
45 5 40
50 50 50
15 6 15
channel matching is the absolute value of the difference in propagation delays between any two channels with inputs on the same side of the isolation barrier. 2 Opposing directional channel matching is the absolute value of the difference in propagation delays between any two channels with inputs on opposing sides of the isolation barrier.
Table 5. Input and Output Characteristics
Parameter DC SPECIFICATIONS Logic High Input Threshold Logic Low Input Threshold Logic High Output Voltages Logic Low Output Voltages Undervoltage Lockout Positive Going Threshold Negative Going Threshold Hysterisis Input Currents per Channel AC SPECIFICATIONS Output Rise/Fall Time Common-Mode Transient Immunity 1 Refresh Rate
1
Symbol VIH VIL VOH VOL
Min 0.7 VISO or 0.7 VDD1
Typ
Max
Unit V V V V V V V V V A ns kV/s Mbps
Test Conditions
0.3 VISO or 0.3 VDD1 VDD1 - 0.3 or VISO - 0.3 VDD1 - 0.5 or VISO - 0.5 5.0 4.8 0.0 0.2 2.7 2.4 0.3 +0.01 2.5 35 1.0
0.1 0.4
IOx = -20 A, VIx = VIxH IOx = -4 mA, VIx = VIxH IOx = 20 A, VIx = VIxL IOx = 4 mA, VIx = VIxL VDD1, VDDL, VISO supply
VUV+ VUV- VUVH II tR/tF |CM| fr
-20
+20
0 V VIx VDDX 10% to 90% VIx= VDD1 or VISO, VCM = 1000 V, transient magnitude = 800 V
25
|CM| is the maximum common-mode voltage slew rate that can be sustained while maintaining VO > 0.8 x VDD1 or 0.8 x VISO for a high input or VO < 0.8 x VDD1 or 0.8 x VISO for a low input. The common-mode voltage slew rates apply to both rising and falling common-mode voltage edges.
Rev. 0 | Page 4 of 24
ADUM6400/ADuM6401/ADuM6402/ADuM6403/ADuM6404
ELECTRICAL CHARACTERISTICS--3.3 V PRIMARY INPUT SUPPLY/3.3 V SECONDARY ISOLATED SUPPLY
All typical specifications are at TA = 25C, VDD1 = VISO = 3.3 V, VSEL = GNDISO. Minimum/maximum specifications apply over the entire recommended operation range which is 3.0 V VDD1, VSEL, VISO 3.6 V; and -40C TA +105C, unless otherwise noted. Switching specifications are tested with CL = 15 pF and CMOS signal levels, unless otherwise noted. Table 6. DC-to-DC Converter Static Specifications
Parameter DC-TO-DC CONVERTER SUPPLY Setpoint Line Regulation Load Regulation Output Ripple Output Noise Switching Frequency PW Modulation Frequency Output Supply Efficiency at IISO (MAX) IDD1, No VISO Load IDD1, Full VISO Load Symbol VISO VISO (LINE) VISO (LOAD) VISO (RIP) VISO (NOISE) fOSC fPWM IISO (MAX) IDD1 (Q) IDD1 (MAX) Min 3.0 Typ 3.3 1 1 50 130 180 625 33 14 175 Max 3.6 5 Unit V mV/V % mV p-p mV p-p MHz kHz mA % mA mA Test Conditions IISO = 0 mA IISO = 30 mA, VDD1 = 3.0 V to 3.6 V IISO = 6 mA to 54 mA 20 MHz bandwidth, CBO = 0.1 F||10 F, IISO = 54 mA CBO = 0.1 F||10 F, IISO = 54 mA
60 20
VISO > 3 V IISO = 60 mA
Table 7. DC-to-DC Converter Dynamic Specifications
Parameter SUPPLY CURRENT ADUM6400 ADuM6401 ADuM6402 ADuM6403 ADuM6404 Symbol IDD1 IISO (LOAD) IDD1 IISO (LOAD) IDD1 IISO (LOAD) IDD1 IISO (LOAD) IDD1 IISO (LOAD) 2 Mbps--A Grade, B Grade, C Grade Min Typ Max 14 60 14 60 14 60 14 60 14 60 25 Mbps--C Grade Min Typ Max 41 43 44 42 46 41 47 39 51 38 Unit mA mA mA mA mA mA mA mA mA mA Test Conditions No VISO load No VISO load No VISO load No VISO load No VISO load
Table 8. Switching Specifications
Parameter SWITCHING SPECIFICATIONS Data Rate Propagation Delay Pulse Width Distortion Change vs. Temperature Pulse Width Propagation Delay Skew Channel Matching Codirectional 1 Opposing Directional 2
1
7Codirectional
Symbol
Min
A Grade Typ Max 1 100 40
Min
C Grade Typ Max 25 60 6
Unit Mbps ns ns ps/C ns ns ns ns
Test Conditions Within PWD limit 50% input to 50% output |tPLH - tPHL| Within PWD limit Between any two units
tPHL, tPLH PWD PW tPSK tPSKCD tPSKOD 1000
60
45 5 40
50 50 50
45 6 15
channel matching is the absolute value of the difference in propagation delays between any two channels with inputs on the same side of the isolation barrier. 2 Opposing directional channel matching is the absolute value of the difference in propagation delays between any two channels with inputs on opposing sides of the isolation barrier.
Rev. 0 | Page 5 of 24
ADUM6400/ADuM6401/ADuM6402/ADuM6403/ADuM6404
Table 9. Input and Output Characteristics
Parameter DC SPECIFICATIONS Logic High Input Threshold Logic Low Input Threshold Logic High Output Voltages Logic Low Output Voltages Undervoltage Lockout Positive Going Threshold Negative Going Threshold Hysterisis Input Currents per Channel AC SPECIFICATIONS Output Rise/Fall Time Common-Mode Transient Immunity 1 Refresh Rate
1
Symbol VIH VIL VOH VOL
Min 0.7 VISO or 0.7 VDD1
Typ
Max
Unit V V V V V V V V V A ns kV/s Mbps
Test Conditions
0.3 VISO or 0.3 VDD1 VDD1 - 0.2 or VISO - 0.2 VDD1 - 0.5 or VISO - 0.5 3.3 3.1 0.0 0.0 2.7 2.4 0.3 +0.01 2.5 35 1.0
0.1 0.4
IOx = -20 A, VIx = VIxH IOx = -4 mA, VIx = VIxH IOx = 20 A, VIx = VIxL IOx = 4 mA, VIx = VIxL VDD1, VDDL, VISO supply
VUV+ VUV- VUVH II tR/tF |CM| fr
-10
+10
0 V VIx VDDX 10% to 90% VIx = VDD1 or VISO, VCM = 1000 V, transient magnitude = 800 V
25
|CM| is the maximum common-mode voltage slew rate that can be sustained while maintaining VO > 0.8 x VDD1 or 0.8 x VISO for a high input or VO < 0.8 x VDD1 or 0.8 x VISO for a low input. The common-mode voltage slew rates apply to both rising and falling common-mode voltage edges.
ELECTRICAL CHARACTERISTICS--5 V PRIMARY INPUT SUPPLY/3.3 V SECONDARY ISOLATED SUPPLY
All typical specifications are at TA = 25C, VDD1 = 5.0 V, VISO = 3.3 V, VSEL = GNDISO. Minimum/maximum specifications apply over the entire recommended operation range which is 4.5 V VDD1 5.5 V, 3.0 V VISO 3.6 V; and -40C TA +105C, unless otherwise noted. Switching specifications are tested with CL = 15 pF and CMOS signal levels, unless otherwise noted. Table 10. DC-to-DC Converter Static Specifications
Parameter DC-TO-DC CONVERTER SUPPLY Setpoint Line Regulation Load Regulation Output Ripple Output Noise Switching Frequency PW Modulation Frequency Output Supply Efficiency at IISO (MAX) IDD1, No VISO Load IDD1, Full VISO Load Symbol VISO VISO (LINE) VISO (LOAD) VISO (RIP) VISO (NOISE) fOSC fPWM IISO (MAX) IDD1 (Q) IDD1 (MAX) Min 3.0 Typ 3.3 1 1 50 130 180 625 30 14 230 Max 3.6 5 Unit V mV/V % mV p-p mV p-p MHz kHz mA % mA mA Test Conditions IISO = 0 mA IISO = 50 mA, VDD1 = 3.0 V to 3.6 V IISO = 6 mA to 54 mA 20 MHz bandwidth, CBO = 0.1 F||10 F, IISO = 90 mA CBO = 0.1 F||10 F, IISO = 90 mA
100 20
VISO > 3 V IISO = 90 mA
Rev. 0 | Page 6 of 24
ADUM6400/ADuM6401/ADuM6402/ADuM6403/ADuM6404
Table 11. DC-to-DC Converter Dynamic Specifications
Parameter SUPPLY CURRENT ADUM6400 ADuM6401 ADuM6402 ADuM6403 ADuM6404 Symbol IDD1 IISO (LOAD) IDD1 IISO (LOAD) IDD1 IISO (LOAD) IDD1 IISO (LOAD) IDD1 IISO (LOAD) 2 Mbps--A Grade, B Grade, C Grade Min Typ Max 9 100 9 100 9 100 9 100 9 100 25 Mbps--C Grade Min Typ Max 43 93 44 92 45 91 46 89 47 88 Unit mA mA mA mA mA mA mA mA mA mA Test Conditions No VISO load No VISO load No VISO load No VISO load No VISO load
Table 12. Switching Specifications
Parameter SWITCHING SPECIFICATIONS Data Rate Propagation Delay Pulse Width Distortion Change vs. Temperature Pulse Width Propagation Delay Skew Channel Matching Codirectional 1 Opposing Directional 2
1 2
7
Symbol
Min
A Grade Typ Max 1 100 40
Min
C Grade Typ Max 25 60 6
Unit Mbps ns ns ps/C ns ns ns ns
Test Conditions Within PWD limit 50% input to 50% output |tPLH - tPHL| Within PWD limit Between any two units
tPHL, tPLH PWD PW tPSK tPSKCD tPSKOD 1000
60
45 5 40
50 50 50
15 6 15
Codirectional channel matching is the absolute value of the difference in propagation delays between any two channels with inputs on the same side of the isolation barrier. Opposing directional channel matching is the absolute value of the difference in propagation delays between any two channels with inputs on opposing sides of the isolation barrier.
Table 13. Input and Output Characteristics
Parameter DC SPECIFICATIONS Logic High Input Threshold Logic Low Input Threshold Logic High Output Voltages Symbol VIH VIL VOH Min 0.7 VISO or 0.7 VDD1 0.3 VISO or 0.3 VDD1 VDD1 - 0.2, VISO - 0.2 VDD1 - 0.5 or VISO - 0.5 VDD1 or VISO VDD1 - 0.2 or VISO - 0.2 0.0 0.0 2.7 2.4 0.3 +0.01 2.5 35 1.0 Typ Max Unit V V V V V V V V V A ns kV/s Mbps Test Conditions
IOx = -20 A, VIx = VIxH IOx = -4 mA, VIx = VIxH IOx = 20 A, VIx = VIxL IOx = 4 mA, VIx = VIxL VDD1, VDDL, VISO supply
Logic Low Output Voltages Undervoltage Lockout Positive Going Threshold Negative Going Threshold Hysterisis Input Currents per Channel AC SPECIFICATIONS Output Rise/Fall Time Common-Mode Transient Immunity 1 Refresh Rate
1
VOL
0.1 0.4
VUV+ VUV- VUVH II tR/tF |CM| fr
-10
+10
0 V VIx VDDx 10% to 90% VIx = VDD1 or VISO, VCM = 1000 V, transient magnitude = 800 V
25
|CM| is the maximum common-mode voltage slew rate that can be sustained while maintaining VO > 0.8 x VDD1 or 0.8 x VISO for a high input or VO < 0.8 x VDD1 or 0.8 x VISO for a low input. The common-mode voltage slew rates apply to both rising and falling common-mode voltage edges. Rev. 0 | Page 7 of 24
ADUM6400/ADuM6401/ADuM6402/ADuM6403/ADuM6404
PACKAGE CHARACTERISTICS
Table 14. Thermal and Isolation Characteristics
Parameter Resistance (Input to Output) 1 Capacitance (Input to Output)1 Input Capacitance 2 IC Junction to Ambient Thermal Resistance
1 2
Symbol RI-O CI-O CI JA
Min
Typ 1012 2.2 4.0 45
Max
Unit pF pF C/W
Test Conditions f = 1 MHz Thermocouple located at center of package underside, test conducted on 4-layer board with thin traces 3
The device is considered a 2-terminal device: Pin 1 to Pin 8 are shorted together; and Pin 9 to Pin 16 are shorted together. Input capacitance is from any input data pin to ground. 3 See the Thermal Analysis section for thermal model definitions.
REGULATORY APPROVALS
Table 15.
UL (Pending) 1 Recognized under 1577 component recognition program1 5000 V rms isolation voltage double protection CSA Approved under CSA Component Acceptance Notice #5A Reinforced insulation per CSA 60950-1-03 and IEC 60950-1, 600 V rms (848 V peak) maximum working voltage Reinforced insulation per IEC 60601-1 250 V rms (353 V peak) maximum working voltage File 205078 VDE (Pending) 2 Certified according to DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 3 Reinforced insulation, 846 V peak
File E214100
1 2
File 2471900-4880-0001
In accordance with UL 1577, each ADuM640x is proof tested by applying an insulation test voltage 6000 V rms for 1 second (current leakage detection limit = 10 A). In accordance with DIN EN 60747-5-2, each ADuM640x is proof tested by applying an insulation test voltage 1590 V peak for 1 second (partial discharge detection limit = 5 pC). 3 In accordance with DIN V VDE V 0884-10, each ADuM640x is proof tested by applying an insulation test voltage 1590 V peak for 1 second (partial discharge detection limit = 5 pC). The * marking branded on the component designates DIN V VDE V 0884-10 approval.
INSULATION AND SAFETY-RELATED SPECIFICATIONS
Table 16. Critical Safety-Related Dimensions and Material Properties
Parameter Rated Dielectric Insulation Voltage Minimum External Air Gap (Clearance) Minimum External Tracking (Creepage) Minimum Internal Gap (Internal Clearance) Tracking Resistance (Comparative Tracking Index) Isolation Group Symbol Value 5000 L(I01) 7.6 L(I02) Unit Test Conditions/Comments V rms 1-minute duration mm Measured from input terminals to output terminals, shortest distance through air >8.0 mm Measured from input terminals to output terminals, shortest distance path along body 0.017 min mm Distance through insulation >400 V IEC 60112 II Material group (DIN VDE 0110, 1/89, Table 1)
CTI
Rev. 0 | Page 8 of 24
ADUM6400/ADuM6401/ADuM6402/ADuM6403/ADuM6404
DIN V VDE V 0884-10 (VDE V 0884-10) INSULATION CHARACTERISTICS
These isolators are suitable for reinforced electrical isolation only within the safety limit data. Maintenance of the safety data is ensured by the protective circuits. The asterisk (*) marking on packages denotes DIN V VDE V 0884-10 approval. Table 17. VDE Characteristics
Description Installation Classification per DIN VDE 0110 For Rated Mains Voltage 150 V rms For Rated Mains Voltage 300 V rms For Rated Mains Voltage 400 V rms Climatic Classification Pollution Degree per DIN VDE 0110, Table 1 Maximum Working Insulation Voltage Input-to-Output Test Voltage, Method b1 Input-to-Output Test Voltage, Method a After Environmental Tests Subgroup 1 After Input and/or Safety Test Subgroup 2 and Subgroup 3 Highest Allowable Overvoltage Safety Limiting Values Case Temperature Side 1 IDD1 Current Insulation Resistance at TS Conditions Symbol Characteristic I to IV I to III I to II 40/105/21 2 846 1590 Unit
VIORM x 1.875 = VPR, 100% production test, tm = 1 sec, partial discharge < 5 pC VIORM x 1.6 = VPR, tm = 60 sec, partial discharge < 5 pC VIORM x 1.2 = VPR, tm = 60 sec, partial discharge < 5 pC Transient overvoltage, tTR = 10 sec Maximum value allowed in the event of a failure (see Figure 7)
VIORM VPR VPR
V peak V peak
1375 1018 VTR 6000
V peak V peak V peak
VIO = 500 V
TS IS1 RS
150 555 >109
C mA
600
SAFE OPERATING VDD1 CURRENT (mA)
500
400
300
200
100
0
0
50 100 150 AMBIENT TEMPERATURE (C)
200
Figure 7. Thermal Derating Curve, Dependence of Safety Limiting Values on Case Temperature, per DIN EN 60747-5-2
RECOMMENDED OPERATING CONDITIONS
Table 18.
Parameter Operating Temperature 1 Supply Voltages 2 VDD1 @ VSEL = 0 V VDD1 @ VSEL = VISO Minimum Load
1 2
Symbol TA VDD VDD IISO(MIN)
Min -40 3.0 4.5 10
08141-007
Max +105 5.5 5.5
Unit C V V mA
Operation at 105C requires reduction of the maximum load current as specified in Table 19. Each voltage is relative to its respective ground.
Rev. 0 | Page 9 of 24
ADUM6400/ADuM6401/ADuM6402/ADuM6403/ADuM6404 ABSOLUTE MAXIMUM RATINGS
Ambient temperature = 25C, unless otherwise noted. Table 19.
Parameter Storage Temperature Range (TST) Ambient Operating Temperature Range (TA) Supply Voltages (VDD1, VISO) 1 Input Voltage (VIA, VIB, VIC, VID, VSEL)1, 2 Output Voltage (VOA, VOB, VOC, VOD)1, 2 Average Output Current per Pin 3 Common-Mode Transients 4
1 2
Rating -55C to +150C -40C to +105C -0.5 V to +7.0 V -0.5 V to VDDI + 0.5 V -0.5 V to VDDO + 0.5 V
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
ESD CAUTION
-10 mA to +10 mA -100 kV/s to +100 kV/s
Each voltage is relative to its respective ground. VDDI and VDDO refer to the supply voltages on the input and output sides of a given channel, respectively. See the Printed Circuit Board (PCB) Layout section. 3 See Figure 7 for maximum rated current values for various temperatures. 4 . Common-mode transients exceeding the absolute maximum slew rate may cause latch-up or permanent damage.
Table 20. Maximum Continuous Working Voltage Supporting 50-Year Minimum Lifetime 1
Parameter AC Voltage, Bipolar Waveform AC Voltage, Unipolar Waveform Basic Insulation Reinforced Insulation DC Voltage Basic Insulation Reinforced Insulation
1
Max 424 600 560 600 560
Unit V peak V peak V peak V peak V peak
Applicable Certification All certifications, 50-year operation Working voltage per IEC 60950-1 Working voltage per DIN V VDE V 0884-10 Working voltage per IEC 60950-1 Working voltage per DIN V VDE V 0884-10
Refers to the continuous voltage magnitude imposed across the isolation barrier. See the Insulation Lifetime section for more information.
Rev. 0 | Page 10 of 24
ADUM6400/ADuM6401/ADuM6402/ADuM6403/ADuM6404 PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
VDD1 1 GND1 2 VIA 3 VIB 4 VIC 5 VID 6 VDDL 7 GND1 8
16 15
VISO GNDISO VOA
ADUM6400
14
13 VOB TOP VIEW (Not to Scale) 12 VOC 11 10 9
VOD GNDISO
08141-008
VSEL
Figure 8. ADUM6400 Pin Configuration
Table 21. ADUM6400 Pin Function Descriptions
Pin No. Mnemonic Description 1 VDD1 Primary Supply Voltage, 3.0 V to 5.5 V. Pin 1 and Pin 7 must be connected to the same external voltage source. 2, 8 GND1 Ground 1. Ground reference for isolator primary. Pin 2 and Pin 8 are internally connected, and it is recommended that both pins be connected to a common ground. 3 VIA Logic Input A. 4 VIB Logic Input B. 5 VIC Logic Input C. 6 VID Logic Input D. 7 VDDL Data Channel Supply Voltage, 3.0 V to 5.5 V. Pin 1 and Pin 7 must be connected to the same external voltage source. 9, 15 GNDISO Ground Reference for Isolator Side 2. Pin 9 and Pin 15 are internally connected, and it is recommended that both pins be connected to a common ground. 10 VSEL Output Voltage Selection. When VSEL = VISO, the VISO setpoint is 5.0 V. When VSEL = GNDISO, the VISO setpoint is 3.3 V. 11 VOD Logic Output D. 12 VOC Logic Output C. 13 VOB Logic Output B. 14 VOA Logic Output A. 16 VISO Secondary Supply Voltage Output for External Loads, 3.3 V (VSEL Low) or 5.0 V (VSEL High).
Rev. 0 | Page 11 of 24
ADUM6400/ADuM6401/ADuM6402/ADuM6403/ADuM6404
VDD1 1 GND1 2 VIA 3 VIB 4 VIC 5 VOD 6 VDDL 7 GND1 8
16 15
VISO GNDISO VOA
ADuM6401
14
13 VOB TOP VIEW (Not to Scale) 12 VOC 11 10 9
VID GNDISO
08141-009
VSEL
Figure 9. ADuM6401 Pin Configuration
Table 22. ADuM6401 Pin Function Descriptions
Pin No. Mnemonic Description 1 VDD1 Primary Supply Voltage, 3.0 V to 5.5 V. Pin 1 and Pin 7 must be connected to the same external voltage source. 2, 8 GND1 Ground 1. Ground reference for isolator primary. Pin 2 and Pin 8 are internally connected, and it is recommended that both pins be connected to a common ground. 3 VIA Logic Input A. 4 VIB Logic Input B. 5 VIC Logic Input C. 6 VOD Logic Output D. 7 VDDL Data Channel Supply Voltage, 3.0 V to 5.5 V. Pin 1 and Pin 7 must be connected to the same external voltage source. 9, 15 GNDISO Ground Reference for Isolator Side 2. Pin 9 and Pin 15 are internally connected, and it is recommended that both pins be connected to a common ground. 10 VSEL Output Voltage Selection. When VSEL = VISO, the VISO setpoint is 5.0 V. When VSEL = GNDISO, the VISO setpoint is 3.3 V. 11 VID Logic Input D. 12 VOC Logic Output C. 13 VOB Logic Output B. 14 VOA Logic Output A. 16 VISO Secondary Supply Voltage Output for External Loads, 3.3 V (VSEL Low) or 5.0 V (VSEL High).
Rev. 0 | Page 12 of 24
ADUM6400/ADuM6401/ADuM6402/ADuM6403/ADuM6404
VDD1 1 GND1 2 VIA 3 VIB 4 VOC 5 VOD 6 VDDL 7 GND1 8
16 15
VISO GNDISO VOA
ADuM6402
14
13 VOB TOP VIEW (Not to Scale) 12 VIC 11 10 9
VID GNDISO
08141-010
VSEL
Figure 10. ADuM6402 Pin Configuration
Table 23. ADuM6402 Pin Function Descriptions
Pin No. Mnemonic Description 1 VDD1 Primary Supply Voltage, 3.0 V to 5.5 V. Pin 1 and Pin 7 must be connected to the same external voltage source. 2, 8 GND1 Ground 1. Ground reference for isolator primary. Pin 2 and Pin 8 are internally connected, and it is recommended that both pins be connected to a common ground. 3 VIA Logic Input A. 4 VIB Logic Input B. 5 VOC Logic Output C. 6 VOD Logic Output D. 7 VDDL Data Channel Supply Voltage, 3.0 V to 5.5 V. Pin 1 and Pin 7 must be connected to the same external voltage source. 9, 15 GNDISO Ground Reference for Isolator Side 2. Pin 9 and Pin 15 are internally connected, and it is recommended that both pins be connected to a common ground. 10 VSEL Output Voltage Selection. When VSEL = VISO, the VISO setpoint is 5.0 V. When VSEL = GNDISO, the VISO setpoint is 3.3 V. 11 VID Logic Input D. 12 VIC Logic Input C. 13 VOB Logic Output B. 14 VOA Logic Output A. 16 VISO Secondary Supply Voltage Output for External Loads, 3.3 V (VSEL Low) or 5.0 V (VSEL High).
Rev. 0 | Page 13 of 24
ADUM6400/ADuM6401/ADuM6402/ADuM6403/ADuM6404
VDD1 1 GND1 2 VIA 3 VOB 4 VOC 5 VOD 6 VDDL 7 GND1 8
16 15
VISO GNDISO VOA
ADuM6403
14
13 VIB TOP VIEW (Not to Scale) 12 VIC 11 10 9
VID GNDISO
08141-011
VSEL
Figure 11. ADuM6403 Pin Configuration
Table 24. ADuM6403 Pin Function Descriptions
Pin No. Mnemonic Description 1 VDD1 Primary Supply Voltage, 3.0 V to 5.5 V. Pin 1 and Pin 7 must be connected to the same external voltage source. 2, 8 GND1 Ground 1. Ground reference for isolator primary. Pin 2 and Pin 8 are internally connected, and it is recommended that both pins be connected to a common ground. 3 VIA Logic Input A. 4 VOB Logic Output B. 5 VOC Logic Output C. 6 VOD Logic Output D. 7 VDDL Data Channel Supply Voltage, 3.0 V to 5.5 V. Pin 1 and Pin 7 must be connected to the same external voltage source. 9, 15 GNDISO Ground Reference for Isolator Side 2. Pin 9 and Pin 15 are internally connected, and it is recommended that both pins be connected to a common ground. 10 VSEL Output Voltage Selection. When VSEL = VISO, the VISO setpoint is 5.0 V. When VSEL = GNDISO, the VISO setpoint is 3.3 V. 11 VID Logic Input D. 12 VIC Logic Input C. 13 VIB Logic Input B. 14 VOA Logic Output A. 16 VISO Secondary Supply Voltage Output for External Loads, 3.3 V (VSEL Low) or 5.0 V (VSEL High).
Rev. 0 | Page 14 of 24
ADUM6400/ADuM6401/ADuM6402/ADuM6403/ADuM6404
VDD1 1 GND1 2 VOA 3 VOB 4 VOC 5 VOD 6 VDDL 7 GND1 8
16 15
VISO GNDISO VIA
ADuM6404
14
13 VIB TOP VIEW (Not to Scale) 12 VIC 11 10 9
VID GNDISO
08141-012
VSEL
Figure 12. ADuM6404 Pin Configuration
Table 25. ADuM6404 Pin Function Descriptions
Pin No. Mnemonic Description 1 VDD1 Primary Supply Voltage, 3.0 V to 5.5 V. Pin 1 and Pin 7 must be connected to the same external voltage source. 2, 8 GND1 Ground 1. Ground reference for isolator primary. Pin 2 and Pin 8 are internally connected, and it is recommended that both pins be connected to a common ground. 3 VOA Logic Output A. 4 VOB Logic Output B. 5 VOC Logic Output C. 6 VOD Logic Output D. 7 VDDL Data Channel Supply Voltage, 3.0 V to 5.5 V. Pin 1 and Pin 7 must be connected to the same external voltage source. 9, 15 GNDISO Ground Reference for Isolator Side 2. Pin 9 and Pin 15 are internally connected, and it is recommended that both pins be connected to a common ground. 10 VSEL Output Voltage Selection. When VSEL = VISO, the VISO setpoint is 5.0 V. When VSEL = GNDISO, the VISO setpoint is 3.3 V. 11 VID Logic Input D. 12 VIC Logic Input C. 13 VIB Logic Input B. 14 VIA Logic Input A. 16 VISO Secondary Supply Voltage Output for External Loads, 3.3 V (VSEL Low) or 5.0 V (VSEL High).
TRUTH TABLE
Table 26. Truth Table (Positive Logic)
VIx Input 1 High Low High Low High Low High Low
1
VSEL Input High High Low Low Low Low High High
VDD1 State Powered Powered Powered Powered Powered Powered Powered Powered
VDD1 Input (V) 5.0 5.0 3.3 3.3 5.0 5.0 3.3 3.3
VISO State Powered Powered Powered Powered Powered Powered Powered Powered
VISO Output (V) 5.0 5.0 3.3 3.3 3.3 3.3 5.0 5.0
VOx Output1 High Low High Low High Low High Low
Notes Normal operation, data is high Normal operation, data is low Normal operation, data is high Normal operation, data is low Normal operation, data is high Normal operation, data is low Configuration not recommended Configuration not recommended
VIx and VOx refer to the input and output signals of a given channel (A, B, C, or D).
Rev. 0 | Page 15 of 24
ADUM6400/ADuM6401/ADuM6402/ADuM6403/ADuM6404 TYPICAL PERFORMANCE CHARACTERISTICS
0.40 0.35 0.30
INPUT CURRENT (A)
4.0 3.5 3.0 2.5 2.0 1.5 1.0 IDD1
3.3V INPUT/3.3V OUTPUT 5V INPUT/3.3V OUTPUT 5V INPUT/5V OUTPUT
08141-033
4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 6.5
POWER
EFFICIENCY (%)
0.20 0.15 0.10 0.05 0
0.5 0 3.0
POWER (W)
08141-036
0.25
0
0.02
0.04 0.06 0.08 OUTPUT CURRENT (A)
0.10
0.12
3.5
4.0
4.5
5.0
5.5
6.0
INPUT SUPPLY VOLTAGE (V)
Figure 13. Typical Power Supply Efficiency at 5 V/5 V, 5 V/3.3 V, and 3.3 V/3.3 V
1.0 0.9 0.8
POWER DISSIPATION (W)
Figure 16. Typical Short-Circuit Input Current and Power vs. VDD1 Supply Voltage
0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 0 0.02 0.04 0.06 0.08 0.10 0.12 VDD1 = 5V, VISO = 5V VDD1 = 5V, VISO = 3V VDD1 = 3.3V, VISO = 3.3V
08141-034
OUTPUT VOLTAGE (500mV/DIV)
10% LOAD
90% LOAD
DYNAMIC LOAD
(100s/DIV)
IISO (A)
Figure 14. Typical Total Power Dissipation vs. IISO with Data Channels Idle
0.12
Figure 17. Typical VISO Transient Load Response, 5 V Output, 10% to 90% Load Step
OUTPUT VOLTAGE (500mV/DIV)
0.10
OUTPUT CURRENT (A)
0.08
0.06
DYNAMIC LOAD
0.04
10% LOAD
90% LOAD
08141-035
0
0
0.05
0.10
0.15
0.20
0.25
0.30
0.35
(100s/DIV)
INPUT CURRENT (A)
Figure 15. Typical Isolated Output Supply Current, IISO, as a Function of External Load, No Dynamic Current Draw at 5 V/5 V, 5 V/3.3 V, and 3.3 V/3.3 V
Figure 18. Typical Transient Load Response, 3 V Output, 10% to 90% Load Step
Rev. 0 | Page 16 of 24
08141-038
0.02
3.3V INPUT/3.3V OUTPUT 5V INPUT/3.3V OUTPUT 5V INPUT/5V OUTPUT
08141-037
ADUM6400/ADuM6401/ADuM6402/ADuM6403/ADuM6404
20
5V INPUT/5V OUTPUT 3.3V INPUT/3.3V OUTPUT 5V INPUT/3.3V OUTPUT
5V OUTPUT RIPPLE (10mV/DIV)
16
SUPPLY CURRENT (mA)
08141-039
12
8
4
BW = 20MHz (400ns/DIV)
0
5
10 15 DATA RATE (Mbps)
20
25
Figure 19. Typical VISO = 5 V Output Voltage Ripple at 90% Load
Figure 22. Typical ICHn Supply Current per Reverse Data Channel (15 pF Output Load)
5
3.3V OUTPUT RIPPLE (10mV/DIV)
4
SUPPLY CURRENT (mA)
3
5V
2
3.3V
1
08141-040
0
5
BW = 20MHz (400ns/DIV)
10 15 DATA RATE (Mbps)
20
25
Figure 20. Typical VISO = 3.3 V Output Voltage Ripple at 90% Load
Figure 23. Typical IISO (D) Dynamic Supply Current per Input
20
5V INPUT/5V OUTPUT 3.3V INPUT/3.3V OUTPUT 5V INPUT/3.3V OUTPUT
3.0
16
2.5
SUPPLY CURRENT (mA)
SUPPLY CURRENT (mA)
2.0
12
1.5
5V
8
1.0
3.3V
4
0.5
08141-041
0
5
10 15 DATA RATE (Mbps)
20
25
0
5
10 15 DATA RATE (Mbps)
20
25
Figure 21. Typical ICHn Supply Current per Forward Data Channel (15 pF Output Load)
Figure 24. Typical IISO (D) Dynamic Supply Current per Output (15 pF Output Load)
Rev. 0 | Page 17 of 24
08141-044
0
0
08141-043
0
08141-042
0
ADUM6400/ADuM6401/ADuM6402/ADuM6403/ADuM6404 TERMINOLOGY
IDD1 (Q) IDD1(Q) is the minimum operating current drawn at the VDD1 pin when there is no external load at VISO and the I/O pins are operating below 2 Mbps, requiring no additional dynamic supply current. IDD1(Q) reflects the minimum current operating condition. IDD1 (D) IDD1 (D) is the typical input supply current with all channels simultaneously driven at a maximum data rate of 25 Mbps with full capacitive load representing the maximum dynamic load conditions. Resistive loads on the outputs should be treated separately from the dynamic load. IDD1 (MAX) IDD1 (MAX) is the input current under full dynamic and VISO load conditions. tPHL Propagation Delay tPHL propagation delay is measured from the 50% level of the falling edge of the VIx signal to the 50% level of the falling edge of the VOx signal. tPLH Propagation Delay tPLH propagation delay is measured from the 50% level of the rising edge of the VIx signal to the 50% level of the rising edge of the VOx signal. tPSK Propagation Delay Skew tPSK is the magnitude of the worst-case difference in tPHL and/or tPLH that is measured between units at the same operating temperature, supply voltages, and output load within the recommended operating conditions. tPSKCD/tPSKOD Channel-to-Channel Matching Channel-to-channel matching is the absolute value of the difference in propagation delays between the two channels when operated with identical loads. Minimum Pulse Width The minimum pulse width is the shortest pulse width at which the specified pulse width distortion is guaranteed. Maximum Data Rate The maximum data rate is the fastest data rate at which the specified pulse width distortion is guaranteed.
Rev. 0 | Page 18 of 24
ADUM6400/ADuM6401/ADuM6402/ADuM6403/ADuM6404 APPLICATIONS INFORMATION
THEORY OF OPERATION
The dc-to-dc converter section of the ADuM640x works on principles that are common to most modern power supplies. It is a secondary side controller architecture with isolated pulsewidth modulation (PWM) feedback. VDD1 power is supplied to an oscillating circuit that switches current into a chip-scale air core transformer. Power transferred to the secondary side is rectified and regulated to either 3.3 V or 5 V. The secondary (VISO) side controller regulates the output by creating a PWM control signal that is sent to the primary (VDD1) side by a dedicated iCoupler data channel. The PWM modulates the oscillator circuit to control the power being sent to the secondary side. Feedback allows for significantly higher power and efficiency. The ADuM640x implement undervoltage lockout (UVLO) with hysteresis on the VDD1 power input. This feature ensures that the converter does not go into oscillation due to noisy input power or slow power-on ramp rates. A minimum load current of 10 mA is recommended to ensure optimum load regulation. Smaller loads can generate excess noise on chip due to short or erratic PWM pulses. Excess noise generated this way can cause data corruption, in some circumstances.
BYPASS < 2mm VDD1 GND1 VIA/VOA VIB/VOB VIC/VOC VID/VOD VDDL GND1 VISO GNDISO VIA/VOA VIB/VOB VIC/VOC VID/VOD GNDISO
08141-025
VSEL
Figure 25. Recommended Printed Circuit Board Layout
In applications involving high common-mode transients, ensure that board coupling across the isolation barrier is minimized. Furthermore, design the board layout such that any coupling that does occur equally affects all pins on a given component side. Failure to ensure this can cause voltage differentials between pins, exceeding the absolute maximum ratings specified in Table 19, thereby leading to latch-up and/or permanent damage. The ADuM640x are power devices that dissipate about 1 W of power when fully loaded and running at maximum speed. Because it is not possible to apply a heat sink to an isolation device, the devices primarily depend on heat dissipation into the PCB through the GND pins. If the devices are used at high ambient temperatures, provide a thermal path from the GND pins to the PCB ground plane. The board layout in Figure 25 shows enlarged pads for Pin 8 and Pin 9. Large diameter vias should be implemented from the pad to the ground, and power planes should be used to reduce inductance. Multiple vias in the thermal pads can significantly reduce temperatures inside the chip. The dimensions of the expanded pads are left to the discretion of the designer and the available board space.
PRINTED CIRCUIT BOARD (PCB) LAYOUT
The ADuM640x digital isolators with 0.5 W isoPower integrated dc-to-dc converters require no external interface circuitry for the logic interfaces. Power supply bypassing is required at the input and output supply pins (see Figure 25). Note that a low ESR bypass capacitor is required between Pin 1 and Pin 2, as close to the chip pads as possible. The power supply section of the ADuM640x uses a 180 MHz oscillator frequency to efficiently pass power through its chip scale transformers. In addition, normal operation of the data section of the iCoupler introduces switching transients on the power supply pins. Bypass capacitors are required for several operating frequencies. Noise suppression requires a low inductance, high frequency capacitor; ripple suppression and proper regulation require a large value capacitor. These are most conveniently connected between Pin 1 and Pin 2 for VDD1 and between Pin 15 and Pin 16 for VISO. To suppress noise and reduce ripple, a parallel combination of at least two capacitors is required. The recommended capacitor values are 0.1 F and 10 F for VDD1. The smaller capacitor must have a low ESR; for example, use of a ceramic capacitor is advised. Note that the total lead length between the ends of the low ESR capacitor and the input power supply pin must not exceed 2 mm. Installing the bypass capacitor with traces more than 2 mm in length may result in data corruption. A bypass between Pin 1 and Pin 8 and between Pin 9 and Pin 16 should also be considered unless both common ground pins are connected together close to the package.
THERMAL ANALYSIS
The ADuM640x parts consist of four internal die attached to a split lead frame with two die attach paddles. For the purposes of thermal analysis, the die is treated as a thermal unit, with the highest junction temperature reflected in the JA from Table 14. The value of JA is based on measurements taken with the parts mounted on a JEDEC standard, 4-layer board with fine width traces and still air. Under normal operating conditions, the ADuM640x devices operate at full load across the full temperature range without derating the output current. However, following the recommendations in the Printed Circuit Board (PCB) Layout section decreases thermal resistance to the PCB, allowing increased thermal margins in high ambient temperatures.
Rev. 0 | Page 19 of 24
ADUM6400/ADuM6401/ADuM6402/ADuM6403/ADuM6404
PROPAGATION DELAY-RELATED PARAMETERS
Propagation delay is a parameter that describes the time it takes a logic signal to propagate through a component (see Figure 26). The propagation delay to a logic low output may differ from the propagation delay to a logic high.
INPUT (VIx) 50%
The limitation on the ADuM640x magnetic field immunity is set by the condition in which induced voltage in the transformer receiving coil is sufficiently large to either falsely set or reset the decoder. The following analysis defines the conditions under which this can occur. The 3.3 V operating condition of the ADuM640x is examined because it represents the most susceptible mode of operation. The pulses at the transformer output have an amplitude of >1.0 V. The decoder has a sensing threshold of about 0.5 V, thus establishing a 0.5 V margin in which induced voltages can be tolerated. The voltage induced across the receiving coil is given by V = (-d/dt)rn2; n = 1, 2, ... , N where: is the magnetic flux density (gauss). N is the number of turns in the receiving coil. rn is the radius of the nth turn in the receiving coil (cm). Given the geometry of the receiving coil in the ADuM640x, and an imposed requirement that the induced voltage be, at most, 50% of the 0.5 V margin at the decoder, a maximum allowable magnetic field is calculated as shown in Figure 27.
100 MAXIMUM ALLOWABLE MAGNETIC FLUX DENSITY (kgauss)
tPLH
OUTPUT (VOx)
tPHL
50%
08141-026
Figure 26. Propagation Delay Parameters
Pulse width distortion is the maximum difference between these two propagation delay values and is an indication of how accurately the input signal timing is preserved. Channel-to-channel matching refers to the maximum amount the propagation delay differs between channels within a single ADuM640x component. Propagation delay skew refers to the maximum amount the propagation delay differs between multiple ADuM640x components operating under the same conditions.
EMI CONSIDERATIONS
The dc-to-dc converter section of the ADuM640x components must, of necessity, operate at a very high frequency to allow efficient power transfer through the small transformers. This creates high frequency currents that can propagate in circuit board ground and power planes, causing edge and dipole radiation. Grounded enclosures are recommended for applications that use these devices. If grounded enclosures are not possible, follow good RF design practices in layout of the PCB. See www.analog.com for the most current PCB layout recommendations specifically for the ADuM640x.
10
1
0.1
0.01
Positive and negative logic transitions at the isolator input cause narrow (~1 ns) pulses to be sent to the decoder via the transformer. The decoder is bistable and is, therefore, either set or reset by the pulses, indicating input logic transitions. In the absence of logic transitions at the input for more than 1 s, periodic sets of refresh pulses indicative of the correct input state are sent to ensure dc correctness at the output. If the decoder receives no internal pulses of more than approximately 5 s, the input side is assumed to be unpowered or nonfunctional, in which case, the isolator output is forced to a default high state by the watchdog timer circuit. This situation should only occur in the ADuM640x devices during power-up and power-down operations.
10k 100k 1M 10M MAGNETIC FIELD FREQUENCY (Hz)
100M
Figure 27. Maximum Allowable External Magnetic Flux Density
For example, at a magnetic field frequency of 1 MHz, the maximum allowable magnetic field of 0.2 kgauss induces a voltage of 0.25 V at the receiving coil. This is about 50% of the sensing threshold and does not cause a faulty output transition. Similarly, if such an event occurs during a transmitted pulse (and is of the worst-case polarity), it reduces the received pulse from >1.0 V to 0.75 V, which is still well above the 0.5 V sensing threshold of the decoder.
Rev. 0 | Page 20 of 24
08141-027
DC CORRECTNESS AND MAGNETIC FIELD IMMUNITY
0.001 1k
ADUM6400/ADuM6401/ADuM6402/ADuM6403/ADuM6404
The preceding magnetic flux density values correspond to specific current magnitudes at given distances from the ADuM640x transformers. Figure 28 expresses these allowable current magnitudes as a function of frequency for selected distances. As shown in Figure 28, the ADuM640x are extremely immune and can be affected only by extremely large currents operated at high frequency very close to the component. For the 1 MHz example, a 0.5 kA current placed 5 mm away from the ADuM640x is required to affect component operation.
1k
MAXIMUM ALLOWABLE CURRENT (kA)
Dynamic I/O current is consumed only when operating a channel at speeds higher than the refresh rate of fr. The dynamic current of each channel is determined by its data rate. Figure 21 shows the current for a channel in the forward direction, meaning that the input is on the VDD1 side of the part. Figure 22 shows the current for a channel in the reverse direction, meaning that the input is on the VISO side of the part. Both figures assume a typical 15 pF load. The following relationship allows the total IDD1 current to be calculated: IDD1 = (IISO x VISO)/(E x VDD1) + ICHn; n = 1 to 4 (1) where: IDD1 is the total supply input current. ICHn is the current drawn by a single channel determined from Figure 21 or Figure 22, depending on channel direction. IISO is the current drawn by the secondary side external load. E is the power supply efficiency at 100 mA load from Figure 13 at the VISO and VDD1 condition of interest. The maximum external load can be calculated by subtracting the dynamic output load from the maximum allowable load. IISO (LOAD) = IISO (MAX) - IISO (D)n; n = 1 to 4 (2)
DISTANCE = 1m 100
10 DISTANCE = 100mm 1 DISTANCE = 5mm 0.1
1k
10k
100k
1M
10M
100M
08141-028
0.01 MAGNETIC FIELD FREQUENCY (Hz)
Figure 28. Maximum Allowable Current for Various Current-to-ADuM640x Spacings
Note that, in combinations of strong magnetic field and high frequency, any loops formed by PCB traces can induce error voltages sufficiently large to trigger the thresholds of succeeding circuitry. Exercise care in the layout of such traces to avoid this possibility.
where: IISO (LOAD) is the current available to supply an external secondary side load. IISO (MAX) is the maximum external secondary side load current available at VISO. IISO (D)n is the dynamic load current drawn from VISO by an input or output channel, as shown in Figure 23 and Figure 24. The preceding analysis assumes a 15 pF capacitive load on each data output. If the capacitive load is larger than 15 pF, the additional current must be included in the analysis of IDD1 and IISO (LOAD).
POWER CONSUMPTION
The VDD1 power supply input provides power to the iCoupler data channels, as well as to the power converter. For this reason, the quiescent currents drawn by the data converter and the primary and secondary I/O channels cannot be determined separately. All of these quiescent power demands have been combined into the IDD1 (Q) current, as shown in Figure 29. The total IDD1 supply current is equal to the sum of the quiescent operating current; the dynamic current, IDD1 (D), demanded by the I/O channels; and any external IISO load.
IDD1(Q) IDD1(D) CONVERTER PRIMARY E CONVERTER SECONDARY IISO
POWER CONSIDERATIONS
The ADuM640x power input, data input channels on the primary side, and data channels on the secondary side are all protected from premature operation by UVLO circuitry. Below the minimum operating voltage, the power converter holds its oscillator inactive and all input channel drivers and refresh circuits are idle. Outputs remain in a high impedance state to prevent transmission of undefined states during power-up and power-down operations. During application of power to VDD1, the primary side circuitry is held idle until the UVLO preset voltage is reached. At that time, the data channels initialize to their default low output state until they receive data pulses from the secondary side.
IDDP(D)
IISO(D)
PRIMARY DATA INPUT/OUTPUT 4-CHANNEL
SECONDARY DATA INPUT/OUTPUT 4-CHANNEL
08141-029
Figure 29. Power Consumption Within the ADuM640x
Rev. 0 | Page 21 of 24
ADUM6400/ADuM6401/ADuM6402/ADuM6403/ADuM6404
When the primary side is above the UVLO threshold, the data input channels sample their inputs and begin sending encoded pulses to the inactive secondary output channels. The outputs on the primary side remain in their default low state because no data comes from the secondary side inputs until secondary power is established. The primary side oscillator also begins to operate, transferring power to the secondary power circuits. The secondary VISO voltage is below its UVLO limit at this point; the regulation control signal from the secondary is not being generated. The primary side power oscillator is allowed to free run in this circumstance, supplying the maximum amount of power to the secondary, until the secondary voltage rises to its regulation setpoint. This creates a large inrush current transient at VDD1. When the regulation point is reached, the regulation control circuit produces the regulation control signal that modulates the oscillator on the primary side. The VDD1 current is reduced and is then proportional to the load current. The inrush current is less than the short-circuit current shown in Figure 16. The duration of the inrush depends on the VISO loading conditions and the current available at the VDD1 pin. As the secondary side converter begins to accept power from the primary, the VISO voltage starts to rise. When the secondary side UVLO is reached, the secondary side outputs are initialized to their default low state until data is received from the corresponding primary side input. It can take up to 1 s after the secondary side is initialized for the state of the output to correlate with the primary side input. Secondary side inputs sample their state and transmit it to the primary side. Outputs are valid about 1 s after the secondary side becomes active. Because the rate of charge of the secondary side power supply is dependent on loading conditions, the input voltage, and the output voltage level selected, take care with the design to allow the converter sufficient time to stabilize before valid data is required. When power is removed from VDD1, the primary side converter and coupler shut down when the UVLO level is reached. The secondary side stops receiving power and starts to discharge. The outputs on the secondary side hold the last state that they received from the primary side. Either the UVLO level is reached and the outputs are placed in their high impedance state, or the outputs detect a lack of activity from the primary side inputs and the outputs are set to their default low value before the secondary power reaches UVLO. Accelerated life testing is performed using voltage levels higher than the rated continuous working voltage. Acceleration factors for several operating conditions are determined, allowing calculation of the time to failure at the working voltage of interest. The values shown in Table 20 summarize the peak voltages for 50 years of service life in several operating conditions. In many cases, the working voltage approved by agency testing is higher than the 50-year service life voltage. Operation at working voltages higher than the service life voltage listed leads to premature insulation failure. The insulation lifetime of the ADuM640x depends on the voltage waveform type imposed across the isolation barrier. The iCoupler insulation structure degrades at different rates, depending on whether the waveform is bipolar ac, unipolar ac, or dc. Figure 30, Figure 31, and Figure 32 illustrate these different isolation voltage waveforms. Bipolar ac voltage is the most stringent environment. A 50-year operating lifetime under the bipolar ac condition determines the Analog Devices recommended maximum working voltage. In the case of unipolar ac or dc voltage, the stress on the insulation is significantly lower. This allows operation at higher working voltages while still achieving a 50-year service life. The working voltages listed in Table 20 can be applied while maintaining the 50-year minimum lifetime, provided the voltage conforms to either the unipolar ac or dc voltage cases. Any cross-insulation voltage waveform that does not conform to Figure 31 or Figure 32 should be treated as a bipolar ac waveform, and its peak voltage should be limited to the 50-year lifetime voltage value listed in Table 20.
RATED PEAK VOLTAGE 0V
08141-030
Figure 30. Bipolar AC Waveform
RATED PEAK VOLTAGE
08141-031
0V
Figure 31. DC Waveform
RATED PEAK VOLTAGE
INSULATION LIFETIME
All insulation structures eventually break down when subjected to voltage stress over a sufficiently long period. The rate of insulation degradation is dependent on the characteristics of the voltage waveform applied across the insulation. Analog Devices conducts an extensive set of evaluations to determine the lifetime of the insulation structure within the ADuM640x.
0V
Figure 32. Unipolar AC Waveform
Rev. 0 | Page 22 of 24
08141-032
NOTES 1. THE VOLTAGE IS SHOWN AS SINUSOIDAL FOR ILLUSTRATION PURPOSES ONLY. IT IS MEANT TO REPRESENT ANY VOLTAGE WAVEFORM VARYING BETWEEN 0 AND SOME LIMITING VALUE. THE LIMITING VALUE CAN BE POSITIVE OR NEGATIVE, BUT THE VOLTAGE CANNOT CROSS 0V.
ADUM6400/ADuM6401/ADuM6402/ADuM6403/ADuM6404 OUTLINE DIMENSIONS
10.50 (0.4134) 10.10 (0.3976)
16
9
7.60 (0.2992) 7.40 (0.2913)
1 8
10.65 (0.4193) 10.00 (0.3937)
1.27 (0.0500) BSC 0.30 (0.0118) 0.10 (0.0039) COPLANARITY 0.10 0.51 (0.0201) 0.31 (0.0122)
2.65 (0.1043) 2.35 (0.0925)
0.75 (0.0295) 0.25 (0.0098)
8 0 0.33 (0.0130) 0.20 (0.0079)
45
SEATING PLANE
1.27 (0.0500) 0.40 (0.0157)
COMPLIANT TO JEDEC STANDARDS MS-013- AA CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 33. 16-Lead Standard Small Outline Package [SOIC_W] Wide Body (RW-16) Dimensions shown in millimeters and (inches)
ORDERING GUIDE
Model ADUM6400ARWZ1, 2 ADUM6400CRWZ1, 2 ADuM6401ARWZ1, 2 ADuM6401CRWZ1, 2 ADuM6402ARWZ1, 2 ADuM6402CRWZ1, 2 ADuM6403ARWZ1, 2 ADuM6403CRWZ1, 2 ADuM6404ARWZ1, 2 ADuM6404CRWZ1, 2
1 2
Number of Inputs, VDD1 Side 4 4 3 3 2 2 1 1 0 0
Number of Inputs, VISO Side 0 0 1 1 2 2 3 3 4 4
Maximum Data Rate (Mbps) 1 25 1 25 1 25 1 25 1 25
Maximum Propagation Delay, 5 V (ns) 100 60 100 60 100 60 100 60 100 60
Maximum Pulse Width Distortion (ns) 40 6 40 6 40 6 40 6 40 6
Temperature Range (C) -40 to +105 -40 to +105 -40 to +105 -40 to +105 -40 to +105 -40 to +105 -40 to +105 -40 to +105 -40 to +105 -40 to +105
032707-B
Package Description 16-Lead SOIC_W 16-Lead SOIC_W 16-Lead SOIC_W 16-Lead SOIC_W 16-Lead SOIC_W 16-Lead SOIC_W 16-Lead SOIC_W 16-Lead SOIC_W 16-Lead SOIC_W 16-Lead SOIC_W
Package Option RW-16 RW-16 RW-16 RW-16 RW-16 RW-16 RW-16 RW-16 RW-16 RW-16
Tape and reel are available. The addition of an RL suffix designates a 13-inch (1,000 units) tape and reel option. Z = RoHS Compliant Part.
Rev. 0 | Page 23 of 24
ADUM6400/ADuM6401/ADuM6402/ADuM6403/ADuM6404 NOTES
(c)2009 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D08141-0-5/09(0)
Rev. 0 | Page 24 of 24

▲Up To Search▲

Price & Availability of ADUM6400

	To Download ADUM6400 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .