Selection of field to be sliced data In the case of the main data slice line, the field to be sliced data is selected by bits 2 and 1 of the data slicer control register 1 (address 00EA16). In the case of the sub-data slice line, the field is selected by bits 2 and 1 of the data slicer control register 3. When bit 2 of the data slicer control register 1 is set to "1," it is possible to slice data of both fields (refer to Figure 26). Specification of line to set slice voltage The reference voltage for slicing (slice voltage) is generated by integrating the amplitude of the clock run-in pulse in the particular line (refer to Table 4). Field determination The field determination flag can be read out by bit 5 of the data slicer control register 1. This flag charge at the falling edge of Vsep.
Line Line specified by bits 4 to 0 of CP (Main data slice line) Line specified by bits 7 to 3 of DSC3 (Sub-data slice line)
DSC1 : Data slice control register 1 DSC3 : Data slice control register 3 CP : Caption position register
Video signal
Vertical blanking interval
Composite video signal Vsep
Line 21
Hsep Count value to be set in the caption position register ("11 16" in this case)
Magnified drawing
Hsep Clock run-in Start bit + 16-bit data
Composite video signal
min. max. Time to be set in the start bit position register
Start bit
Fig. 30. Signals in Vertical Blanking Interval
37
P
. e. tion ang ifica t to ch pec c al s subje a fin are not its is is ntic lim : Th tice arame No e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
(6) Reference Voltage Generating Circuit and Comparator
The composite video signal clamped by the clamping circuit is input to the reference voltage generating circuit and the comparator. Reference voltage generating circuit This circuit generates a reference voltage (slice voltage) by using the amplitude of the clock run-in pulse in line specified by the data slice line specification circuit. Connect a capacitor between the VHOLD pin and the VSS pin, and make the length of wiring as short as possible so that a leakage current may not be generated. Comparator The comparator compares the voltage of the composite video signal with the voltage (reference voltage) generated in the reference voltage generating circuit, and converts the composite video signal into a digital value.
7 100
0 Caption position register (CP : address 00E016) Specification main data slice line
Fix these bits to "1002"
Fig. 31. Caption Position Register
(7) Start Bit Detecting Circuit
This circuit detects a start bit at line decided in the data slice line specification circuit. For start bit detection, it is possible to select one of the following two types by using bit 1 of clock run-in register 2 (address 00E716). After the lapse of the time corresponding to the set value of the start bit position register (address 00E116), the first rising of the composite video signal is detected as a start bit. The time is set in bits 0 to 6 of the start bit position register (address 00E116) (refer to Figure 32). Set a value fit for the following conditions. Figure 32 shows the structure of the start bit position register.
7 0 Start bit position register (SP : address 00E116)
Start bit generating time Time from a falling of the horizontal synchronizing signal to occurrence of a start bit = 4 set value ("0016" to "7F16") reference clock period DSC1 bit 7 control bit 0 : Generation of 16 pulses 1 : Generation of 16 pulses and detection of clock run-in pulse (4 to 6 pulses)
Fig. 32. Start Bit Position Register
Time from the falling of the horizontal synchronizing signal to the last rising of the clock run-in
<
4 set value of the start bit position register reference clock period
<
Time from the faling of the horizontal synchronous signal to occurrence of the start bit
38
P
. e. tion ang ifica t to ch pec c al s subje a fin are not its is is ntic lim : Th tice arame No e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
After a falling of the clock run-in pulse set in bits 2 to 0 of clock runin detect register 2 (address 00E916) is detected, a start bit is detected by sampling a comparator output. A sampling clock for sampling is obtained by dividing the reference clock generated in the timing signal generating circuit by 13. Figure 34 shows the structure of clock run-in detect register 2. The contents of bits 2 to 0 of clock run-in detect register 2 and bit 1 of clock run-in register 2 are written at a falling of the horizontal synchronous signal. For this reason, even if an instruction for setting is executed, the contents of the register cannot be rewritten until a falling of the horizontal synchronous signal.
7
0 Clock run-in detect register 2 (CRD2 : address 00E916)
7 100111
0 1 Clock run-in register 2 (CR2 : address 00E7 16) Fix this bit to "1" Start bit detecting method selection bit 0 : Method 1 1 : Method 2 Fix these bits to "100111 2"
Clock run-in pulses for sampling b2 b1 b0 0 0 0 : Not available 0 0 1 : 1st pulse 0 1 0 : 2nd pulse 0 1 1 : 3rd pulse 1 0 0 : 4th pulse 1 0 1 : 5th pulse 1 1 0 : 6th pulse 1 1 1 : 7th pulse Data clock generating time Time from detection of a start bit to occurrence of a data clock = (13 + set value) reference clock period
Fig. 33. Clock Run-in Register 2
Fig. 34. Clock Run-in Detect Register 2
(8) Clock run-in determination circuit
This circuit sets a window in the clock run-in portion in the composite video signal, and then determinates clock run-in by counting the number of pulses in this window. Set the time from a falling of the horizontal synchronizing signal to a start of the window by bits 0 to 5 of the window register (address 00E216; refer to Figure 35). The window ends according to the contents of the setting of the start bit position register (refer to Figure 32).
7 00 0 Window register (WN : address 00E216) Window start time Time from a falling of the horizontal synchronizing signal to a start of the window = 4 set value ("0016" to "3F16") reference clock period Fix these bits to "0"
Fig. 35. Window Register
39
P
. e tion ang ifica t to ch pec c al s subje a fin are not its is is ntic lim : Th tice arame No e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
For the main data slice line, the count value of pulses in the window is stored in clock run-in register 1 (address 00E616; refer to Figure 36). For the sub-data slice line, the count value of pulses in the window is stored in clock run-in register 3 (address 020916; refer to Figure 37). When this count value is 4 to 6, it is determined as a clock run-in. Accordingly, set the count value so that the window may start after the first pulse of the clock run-in (refer to Figure 38). The contents to be set in the window register are written at a falling of the horizontal synchronous signal. For this reason, even if an instruction for setting is executed, the contents of the register cannot be rewritten until a falling of the horizontal synchronous signal. For the main data slice line, reference clock is counted in the period from a falling of the clock pulse set in bits 0 to 2 of clock run-in detect register 2 (address 00E916) to the next falling. The count value is stored in bits 3 to 7 of clock run-in detect register 1 (address 00E816) (When the count value exceeds "1F16," "1F16" is held). For the sub-data slice line, the count value is stored in bits 3 to 7 of clock run-in detect register 3 (address 020816). Read out these bits after the occurence of a data slicer interrupt (refer to (11) Interrupt Request Generating Circuit). Figure 39 shows the structure of clock run-in detect registers 1 and 3.
7 0101
0 Clock run-in register 1 (CR1 : address 00E6 16) Clock run-in count value of main-data slice line Fix these bits to "0101 2"
Fig. 36. Clock Run-in Register 1
7 0 Clock run-in register 3 (CR3 : address 0209 16) Clock run-in count value of sub-data slice line
Data latch completion flag for caption data in sub-data slice line i
0: Data is not latched yet 1: Data is latched Data slice line selection bit for interrupt request
0: Main data slice line 1: Sub-data slice line
Interrupt mode selection bit
0: Interrupt occurs at end of data slice line 1: Interrupt occurs at completion of caption data latch a
Fig. 37. Clock Run-in Register 3
Horizontal synchronous signal Composite video signal Window Time to be set in the window register Time to be set in the start bit position register VWhen the count value in the window is 4 to 6, this is determined as a clock run-in.
Clock run-in
Start bit data + 16-bit data
Fig. 38. Window Setting
7 0 Clock run-in detect registers 1, 3 ( CRD1 : address 00E8 16) ( CRD3 : address 0208 16) Test bits : read-only
Number of reference clocks to be counted in one clock run-in pulse period
Fig. 39. Clock Run-in Detect Registers 1 and 3
40
P
. e tion ang ifica t to ch pec c al s subje fin re a ot a is n limits This ntic ice: arame Not e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
(9) Data clock generating circuit
This circuit generates a data clock synchronized with the start bit detected in the start bit detecting circuit. Set the time from detection of the start bit to occurrence of the data clock in bits 3 to 7 of clock run-in detect register 2 (address 00E916). The time to be set is represented by the following expression: Time = (13 + set value) ! reference clock period
For a data clock, 16 pulses are generated. When just 16 pulses have been generated, bit 7 of the data slicer control register is set to "1" (refer to Figure 26). When method 1 is already selected as a start bit detecting method, this bit becomes a logical product (AND) value with a clock run-in determination result by setting bit 7 of the start bit position register to "1." When method 2 is already selected as a start bit detecting method and 16 pulses are generated of a data clock regardless of bit 7 of the start bit position register, this bit is set to "1." The contents of this bit are reset at a falling of the vertical synchronizing signal (Vsep).
Table 5. Setting Conditions for Caption Data Latch Completion Flag Bit 7 of SP 0 1 Conditions for Setting Bit 7 of DSC1 to "1" Data clock of 16 pulses has occured in main data slaice line Data clock of 16 pulses has occured in main data slaice line AND Clock run-in pulse are detected 4 to 6 times Conditions for Setting Bit 4 of DSC3 to "1" Data clock of 16 pulses has occured in sub-data slaice line Data clock of 16 pulses has occured in sub-data slaice line AND Clock run-in pulse are detected 4 to 6 times
(10) 16-bit Shift Register
The caption data converted into a digital value by the comparator is stored into the 16-bit shift register in synchronization with the data clock. For the main data slice line, the contents of the high-order 8 bits of the stored caption data and the contents of the low-order 8 bits of the same data can be obtained by reading out data register 2 (address 00E516) and data register 1 (address 00E416), respectively. For the sub-data slice line, the contents of the high-order 8 bits and the contents of the low-order 8 bits can be obtained by reading out the data register 4 (address 00ED16) and data register 3 (address 00EC16), respectively. These registers are reset to "0" at a falling of Vsep. Read out data registers 1 and 2 after the occurence of a data slicer interrupt (refer to (11) Interrupt Request Generating Circuit). Table 6. Occurence Sources of Interrupt Request CR3 b5 b6 0 0 0 1 1 0 0 1 1 1 1 0 Sub-data slice line CR2 b1 0 1 Main data slice line
(11) Interrupt Request Generating Circuit
The interrupt requests as shown in Table 6 are generated by combination of the following bits; bits 5 and 6 of the clock run-in register 3 (address 020916), bit 1 of the clock run-in register 2 (address 00E716). Read out the contents of data registers 1 to 4 and the contents of bits 3 to 7 of clock run-in detect registers 1 and 3 after the occurence of a data slicer interrupt request.
Occurence Souces of Interrupt Request Slice line At end of data slice line Data clock of 16 pulses has occured AND Clock run-in pulse are detected 4 to 6 times Data clock of 16 pulses has occured At end of data slice line Data clock of 16 pulses has occured AND Clock run-in pulse are detected 4 to 6 times Data clock of 16 pulses has occured Sources
41
P
. e tion ang ifica t to ch pec c al s subje a fin are not its is is ntic lim : Th tice arame No e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
(12) Synchronous Signal Counter
The synchronous signal counter counts the composite sync signal taken out from a video signal in the data slicer circuit or the vertical synchronous signal Vsep as a count source. The count value in a certain time (T time) generated by f(XIN)/213 or f(XIN)/213 is stored into the 5-bit latch. Accordingly, the latch value changes in the cycle of T time. When the count value exceeds "1F16," "1F16" is stored into the latch. The latch value can be obtained by reading out the sync pulse counter register (address 020F16). A count source is selected by bit 5 of the sync pulse counter register. The synchronous signal counter is used when bit 0 of PWM mode register 1 (address 02EA16). Figure 40 shows the structure of the sync pulse counter and Figure 41 shows the synchronous signal counter block diagram.
7 0 Sync pulse counter register (SYC : address 020F16) Count value
Count source 0: HSYNC signal 1: Composite sync signal
Count time
f(XIN)/213 (1024 s, f(XIN) = 8 MHz)
Fig. 40. Sync Pulse Counter Register
f(XIN)/213
Composite sync signal HSYNC signal
Reset 5-bit counter Counter
b5 Selection gate : connected to black colored side when reset.
Latch (5 bits)
Sync pulse counter register
Data bus
Fig. 41. Synchronous Signal Counter Block Diagram
42
MITSUBISHI MICROCOMPUTERS
n. ange. atio h cific ct to c spe je inal re sub t a f its a o is n lim This entic m ice: Not e para Som
PRE
L
A IMIN
RY
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
MULTI-MASTER I2C-BUS INTERFACE
The multi-master interface is a serial communications circuit, conforming to the Philips I 2C-BUS data transfer format. This interface, offering both arbitration lost detection and a synchronous functions, is useful for the multi-master serial communications. Figure 42 shows a block diagram of the multi-master I2C-BUS interface and Table 7 shows multi-master I2C-BUS interface functions. This multi-master I2C-BUS interface consists of the I2C address register, the I2C data shift register, the I2C clock control register, the I2C control register, the I2C status register and other control circuits. I2C-BUS
Table 7. Multi-master I2C-BUS Interface Functions Item Function In conformity with Philips I2C-BUS standard: 10-bit addressing format 7-bit addressing format High-speed clock mode Standard clock mode In conformity with Philips I2C-BUS standard: Master transmission Master reception Slave transmission Slave reception 16.1 kHz to 400 kHz (at = 4 MHz)
Format
Communication mode
SCL clock frequency
: System clock = f(XIN)/2 Note: We are not responsible for any third party's infringement of patent rights or other rights attributable to the use of the control function (bits 6 and 7 of the I2C control register at address 00F916) for connections between the I2C-BUS interface and ports (SCL1, SCL2, SDA1, SDA2).
b7
I2C address register (S0D)
b0
Interrupt generating circuit Interrupt request signal (IICIRQ)
SAD6 SAD5 SAD4 SAD3 SAD2 SAD1 SAD0 RBW
Address comparator Serial data
(SDA)
Noise elimination circuit
Data control circuit
b7
I 2 C data shift register S0
b0 b7
MST TRX BB PIN
b0
AL AAS AD0 LRB
AL circuit
Internal data bus
I 2 C status register (S1)
BB circuit
Serial clock
(SCL)
Noise elimination circuit
Clock control circuit
b7
ACK
b0
ACK FAST CCR4 CCR3 CCR2 CCR1 CCR0 BIT MODE
b7
BSEL1 BSEL0 10BIT SAD ALS
b0
ESO BC2 BC1 BC0
I2 C clock control register (S2) Clock division
I2C clock control register (S1D) System clock (
)
Bit counter
Fig. 42. Block Diagram of Multi-master I2C-BUS Interface
43
MITSUBISHI MICROCOMPUTERS
. ion. hange c icat ecif ject to l sp fina re sub a not its a is is ntic lim : Th tice arame No e p Som
PRE
L
A IMIN
RY
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
(1) I2C Data Shift Register
The I2C data shift register (S0 : address 00F616) is an 8-bit shift register to store receive data and write transmit data. When transmit data is written into this register, it is transferred to the outside from bit 7 in synchronization with the SCL clock, and each time one-bit data is output, the data of this register are shifted one bit to the left. When data is received, it is input to this register from bit 0 in synchronization with the SCL clock, and each time one-bit data is input, the data of this register are shifted one bit to the left. The I2C data shift register is in a write enable status only when the ESO bit of the I2C control register (address 00F916) is "1." The bit counter is reset by a write instruction to the I2C data shift register. When both the ESO bit and the MST bit of the I2C status register (address 00F816) are "1," the SCL is output by a write instruction to the I2C data shift register. Reading data from the I2C data shift register is always enabled regardless of the ESO bit value. Note: To write data into the I 2C data shift register after setting the MST bit to "0" (slave mode), keep an interval of 8 machine cycles or more.
7 0 I2 C address register (S0D: address 00F716) Read/write bit Slave address
SAD6 SAD5 SAD4 SAD3 SAD2 SAD1 SAD0 RBW
Fig. 43. I 2C Address Register
(3) I2C Clock Control Register
The I 2C clock control register (address 00FA16) is used to set ACK control, SCL mode and SCL frequency. s Bits 0 to 4: SCL Frequency Control Bits (CCR0-CCR4) These bits control the SCL frequency. Refer to Table 7. s Bit 5: SCL Mode Specification Bit (FAST MODE) This bit specifies the SCL mode. When this bit is set to "0," the standard clock mode is set. When the bit is set to "1," the high-speed clock mode is set. s Bit 6: ACK Bit (ACK BIT) This bit sets the SDA status when an ACK clockV is generated. When this bit is set to "0," the ACK return mode is set and SDA goes to LOW at the occurrence of an ACK clock. When the bit is set to "1," the ACK non-return mode is set. The SDA is held in the HIGH status at the occurrence of an ACK clock. However, when the slave address matches the address data in the reception of address data at ACK BIT = "0," the SDA is automatically made LOW (ACK is returned). If there is a mismatch between the slave address and the address data, the SDA is automatically made HIGH (ACK is not returned). VACK clock: Clock for acknowledgement s Bit 7: ACK Clock Bit (ACK) This bit specifies a mode of acknowledgment which is an acknowledgment response of data transmission. When this bit is set to "0," the no ACK clock mode is set. In this case, no ACK clock occurs after data transmission. When the bit is set to "1," the ACK clock mode is set and the master generates an ACK clock upon completion of each 1-byte data transmission.The device for transmitting address data and control data releases the SDA at the occurrence of an ACK clock (make SDA HIGH) and receives the ACK bit generated by the data receiving device. Note: Do not write data into the I2C clock control register during transmission. If data is written during transmission, the I2C clock generator is reset, so that data cannot be transmitted normally.
(2) I2C Address Register
The I 2C address register (address 00F716) consists of a 7-bit slave ___ address and a read/write bit. In the addressing mode, the slave address written in this register is compared with the address data to be received immediately after the START condition are detected. ____ s Bit 0: Read/Write Bit (RBW) Not used when comparing addresses, in the 7-bit addressing mode. In the 10-bit addressing mode, the first address data to be received is compared with the contents (SAD6 to SAD0 + RBW) of the I2C address register. The RBW bit is cleared to "0" automatically when the stop condition is detected. s Bits 1 to 7: Slave Address (SAD0-SAD6) These bits store slave addresses. Regardless of the 7-bit addressing mode and the 10-bit addressing mode, the address data transmitted from the master is compared with the contents of these bits.
44
MITSUBISHI MICROCOMPUTERS
e. n. atio chang cific to spe ubject al a fin re s not mits a li is is : Th mentic ice Not e para Som
PRE
L
R INA IM
Y
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
(4) I2C Control Register
7
ACK
0
ACK FAST CCR4 CCR3 CCR2 CCR1 CCR0 BIT MODE
I2C clock control register (S2 : address 00FA16) SCL frequency control bits Refer to Table 8. SCL mode specification bit 0 : Standard clock mode 1 : High-speed clock mode ACK bit 0 : ACK is returned. 1 : ACK is not returned. ACK clock bit 0 : No ACK clock 1 : ACK clock
Fig. 44. I2C Clock Control Register Table 8. Set Values of I2C Clock Control Register and SCL Frequency Setting value of SCL frequency CCR4-CCR0 (at = 4MHz, unit : kHz) Standard clock High-speed clock CCR4 CCR3 CCR2 CCR1 CCR0 mode mode 0 0 0 0 0 0 0 ... 0 0 0 0 0 0 0 ... 0 0 0 0 1 1 1 ... 0 0 1 1 0 0 1 ... 0 1 0 1 0 1 0 ... Setup disabled Setup disabled Setup disabled Setup disabled Setup disabled 100 83.3 500/CCR value 17.2 16.6 16.1 Setup disabled Setup disabled Setup disabled 333 250 400(Note) 166 1000/CCR value 34.5 33.3 32.3
1 1 1
1 1 1
1 1 1
0 1 1
1 0 1
The I2C control register (address 00F916) controls the data communication format. s Bits 0 to 2: Bit Counter (BC0-BC2) These bits decide the number of bits for the next 1-byte data to be transmitted. An interrupt request signal occurs immediately after the number of bits specified with these bits are transmitted. When a START condition is received, these bits become "0002" and the address data is always transmitted and received in 8 bits. s Bit 3: I2C Interface Use Enable Bit (ESO) This bit enables usage of the multimaster I2C BUS interface. When this bit is set to "0," the use disable status is provided, so the SDA and the SCL become high-impedance. When the bit is set to "1," use of the interface is enabled. When ESO = "0," the following is performed. PIN = "1," BB = "0" and AL = "0" are set (they are bits of the I2C status register at address 00F816 ). Writing data to the I 2C data shift register (address 00F616) is disabled. s Bit 4: Data Format Selection Bit (ALS) This bit decides whether or not to recognize slave addresses. When this bit is set to "0," the addressing format is selected, so that address data is recognized. When a match is found between a slave address and address data as a result of comparison or when a general call (refer to "(5) I2C Status Register," bit 1) is received, transmission processing can be performed. When this bit is set to "1," the free data format is selected, so that slave addresses are not recognized. s Bit 5: Addressing Format Selection Bit (10BIT SAD) This bit selects a slave address specification format. When this bit is set to "0," the 7-bit addressing format is selected. In this case, only the high-order 7 bits (slave address) of the I2C address register (address 00F716) are compared with address data. When this bit is set to "1," the 10-bit addressing format is selected, all the bits of the I2C address register are compared with address data. s Bits 6 and 7: Connection Control Bits between I2C-BUS Interface and Ports (BSEL0, BSEL1) These bits controls the connection between SCL and ports or SDA and ports (refer to Figure 46).
* *
Note: At 400 kHz in the high-speed clock mode, the duty is as below. LOW period : HIGH period = 3 : 2 In the other cases, the duty is 50%.
45
MITSUBISHI MICROCOMPUTERS
. ion. hange c icat ecif ject to l sp fina re sub a not its a is is ntic lim : Th tice arame No e p Som
PRE
L
A IMIN
RY
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
"0" "1" BSEL0 SCL1/P11 SCL Multi-master I2C-BUS interface SDA "0" "1" BSEL1 SCL2/P12 "0" "1" BSEL0 SDA1/P13 "0" "1" BSEL1 SDA2/P14
Bit counter (Number of transmit/receive bits) b2 b1 b0 0 0 0:8 0 0 1:7 0 1 0:6 0 1 1:5 1 0 0:4 1 0 1:3 1 1 0:2 1 1 1:1 I2C-BUS interface use enable bit 0 : Disabled 1 : Enabled Data format selection bit 0 : Addressing format 1 : Free data format Addressing format selection bit 0 : 7-bit addressing format 1 : 10-bit addressing format Connection control bits between I2C-BUS interface and ports b7 b6 Connection port 0 0 : None 0 1 : SCL1, SDA1 1 0 : SCL2, SDA2 1 1 : SCL1, SDA1, SCL2, SDA2 7
BSEL1 BSEL0 10 BIT ALS SAD
0
ESO BC2 BC1 BC0 (S1D : address 00F9 16)
I2C control register
Note: When using multi-master I2C-BUS interface, set bits 3 and 4 of the serial I/O mode register (address 021316) to "1." Moreover, set the corresponding direction register to "1" to use the port as multi-master I2C-BUS interface. Fig. 45. Connection Port Control by BSEL0 and BSEL1
(5) I2C Status Register
The I2C status register (address 00F816) controls the I2C-BUS interface status. The low-order 4 bits are read-only bits and the highorder 4 bits can be read out and written to. s Bit 0: Last Receive Bit (LRB) This bit stores the last bit value of received data and can also be used for ACK receive confirmation. If ACK is returned when an ACK clock occurs, the LRB bit is set to "0." If ACK is not returned, this bit is set to "1." Except in the ACK mode, the last bit value of received data is input. The state of this bit is changed from "1" to "0" by executing a write instruction to the I2C data shift register (address 00F616). s Bit 1: General Call Detecting Flag (AD0) This bit is set to "1" when a general callV whose address data is all "0" is received in the slave mode. By a general call of the master device, every slave device receives control data after the general call. The AD0 bit is set to "0" by detecting the STOP condition or START condition. VGeneral call: The master transmits the general call address "0016" to all slaves. s Bit 2: Slave Address Comparison Flag (AAS) This flag indicates a comparison result of address data. In the slave receive mode, when the 7-bit addressing format is selected, this bit is set to "1" in one of the following conditions. The address data immediately after occurrence of a START condition matches the slave address stored in the high-order 7 bits of the I2C address register (address 00F716). A general call is received. In the slave reception mode, when the 10-bit addressing format is selected, this bit is set to "1" with the following condition. When the address data is compared with the I 2C address register (8 bits consists of slave address and RBW), the first bytes match. The state of this bit is changed from "1" to "0" by executing a write instruction to the I2C data shift register (address 00F616). Fig. 46. I2C Control Register
* * *
46
MITSUBISHI MICROCOMPUTERS
n. ange. atio h cific ct to c spe je inal re sub t a f its a o is n lim This entic m ice: Not e para Som
PRE
L
A IMIN
RY
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
_ _
s Bit 3: Arbitration LostV Detecting Flag (AL) In the master transmission mode, when a device other than the microcomputer sets the SDA to "L,", arbitration is judged to have been lost, so that this bit is set to "1." At the same time, the TRX bit is set to "0," so that immediately after transmission of the byte whose arbitration was lost is completed, the MST bit is set to "0." When arbitration is lost during slave address transmission, the TRX bit is set to "0" and the reception mode is set. Consequently, it becomes possible to receive and recognize its own slave address transmitted by another master device. VArbitration lost: The status in which communication as a master is disabled. s Bit 4: I2C-BUS Interface Interrupt Request Bit (PIN) This bit generates an interrupt request signal. Each time 1-byte data is transmitted, the state of the PIN bit changes from "1" to "0." At the same time, an interrupt request signal is sent to the CPU. The PIN bit is set to "0" in synchronization with a falling edge of the last clock (including the ACK clock) of an internal clock and an interrupt request signal occurs in synchronization with a falling edge of the PIN bit. When the PIN bit is "0," the SCL is kept in the "0" state and clock generation is disabled. Figure 40 shows an interrupt request signal generating timing chart. The PIN bit is set to "1" in any one of the following conditions. Executing a write instruction to the I2C data shift register (address 00F616). When the ESO bit is "0" At reset The conditions in which the PIN bit is set to "0" are shown below: Immediately after completion of 1-byte data transmission (including when arbitration lost is detected) Immediately after completion of 1-byte data reception In the slave reception mode, with ALS = "0" and immediately after completion of slave address or general call address reception In the slave reception mode, with ALS = "1" and immediately after completion of address data reception s Bit 5: Bus Busy Flag (BB) This bit indicates the status of use of the bus system. When this bit is set to "0," this bus system is not busy and a START condition can be generated. When this bit is set to "1," this bus system is busy and the occurrence of a START condition is disabled by the START condition duplication prevention function (Note). This flag can be written by software only in the master transmission mode. In the other modes, this bit is set to "1" by detecting a START condition and set to "0" by detecting a STOP condition. When the ESO bit of the I 2C control register (address 00F916) is "0" and at reset, the BB flag is kept in the "0" state. s Bit 6: Communication Mode Specification Bit (transfer direction specification bit: TRX) This bit decides the direction of transfer for data communication. When this bit is "0," the reception mode is selected and the data of a transmitting device is received. When the bit is "1," the transmission mode is selected and address data and control data are output into the SDA in synchronization with the clock generated on the SCL. When the ALS bit of the I2C control register (address 00F916) is "0" in the slave reception mode is selected, the TRX bit is set to "1" __ (transmit) if the least significant bit (R/W bit) of the address data trans-
* * * * * * *
mitted by the master is "1." When the ALS bit is "0" and the R/W bit is "0," the TRX bit is cleared to "0" (receive). The TRX bit is cleared to "0" in one of the following conditions. When arbitration lost is detected. When a STOP condition is detected. When occurence of a START condition is disabled by the START condition duplication prevention function (Note). With MST = "0" and when a START condition is detected. With MST = "0" and when ACK non-return is detected. At reset s Bit 7: Communication Mode Specification Bit (master/slave specification bit: MST) This bit is used for master/slave specification for data communication. When this bit is "0," the slave is specified, so that a START condition and a STOP condition generated by the master are received, and data communication is performed in synchronization with the clock generated by the master. When this bit is "1," the master is specified and a START condition and a STOP condition are generated, and also the clocks required for data communication are generated on the SCL. The MST bit is cleared to "0" in one of the following conditions. Immediately after completion of 1-byte data transmission when arbitration lost is detected When a STOP condition is detected. When occurence of a START condition is disabled by the START condition duplication preventing function (Note). At reset
* * * * * *
* * * *
Note: The START condition duplication prevention function disables the START condition generation, reset of bit counter reset, and SCL output, when the following condition is satisfied: * a START condition is set by another master device.
47
MITSUBISHI MICROCOMPUTERS
. e. tion ang ifica t to ch pec c al s subje fin re a ot a is n limits This ntic ice: arame Not e p Som
P
REL
A IMIN
RY
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
(6) START Condition Generation Method
7 0 I2C status register (S1 : address 00F816) Last receive bit (Note) 0 : Last bit = "0" 1 : Last bit = "1" General call detecting flag (Note) 0 : No general call detected 1 : General call detected Slave address comparison flag (Note) 0 : Address mismatch 1 : Address match Arbitration lost detecting flag (Note) 0 : Not detected 1 : Detected I2C-BUS interface interrupt request bit 0 : Interrupt request issued 1 : No interrupt request issued Bus busy flag 0 : Bus free 1 : Bus busy Communication mode specification bits 00 : Slave receive mode 01 : Slave transmit mode 10 : Master receive mode 11 : Master transmit mode Note: These bit and flags can be read out but cannot be written.
MST TRX BB PIN AL AAS AD0 LRB
When the ESO bit of the I2C control register (address 00F916) is "1," execute a write instruction to the I2C status register (address 00F816) to set the MST, TRX and BB bits to "1." A START condition will then be generated. After that, the bit counter becomes "0002" and an SCL for 1 byte is output. The START condition generation timing and BB bit set timing are different in the standard clock mode and the highspeed clock mode. Refer to Figure 49 for the START condition generation timing diagram, and Table 9 for the START condition/STOP condition generation timing table.
I2C status register write signal SCL SDA BB flag Setup time Setup time Hold time Set time for BB flag
Fig. 49. START Condition Generation Timing Diagram
(7) RESTART Condition Generation Method
To generate the RESTART condition, take the following sequence: Set "2016" to the I2C status register (S1). Write a transmit data to the I2C data shift register. Set "F016" to the I2C status register (S1) again.
Fig. 47. I 2C Status Register
SCL PIN
IICIRQ
Fig. 48. Interrupt Request Signal Generation Timing
48
MITSUBISHI MICROCOMPUTERS
n. ange. atio h cific ct to c spe je inal re sub t a f its a o is n lim This entic m ice: Not e para Som
PRE
L
A IMIN
RY
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
(8) STOP Condition Generation Method
When the ES0 bit of the I2C control register (address 00F916) is "1," execute a write instruction to the I2C status register (address 00F816) for setting the MST bit and the TRX bit to "1" and the BB bit to "0". A STOP condition will then be generated. The STOP condition generation timing and the BB flag reset timing are different in the standard clock mode and the high-speed clock mode. Refer to Figure 50 for the STOP condition generation timing diagram, and Table 9 for the START condition/STOP condition generation timing table.
(9) START/STOP Condition Detect Conditions
The START/STOP condition detect conditions are shown in Figure 51 and Table 10. Only when the 3 conditions of Table 10 are satisfied, a START/STOP condition can be detected. Note: When a STOP condition is detected in the slave mode (MST = 0), an interrupt request signal "IICIRQ" is generated to the CPU.
I2C status register write signal SCL SDA BB flag Setup time Hold time Reset time for BB flag
SCL release time SCL SDA (START condition) SDA (STOP condition) Setup time Setup time Hold time Hold time
Fig. 50. STOP Condition Generation Timing Diagram
Fig. 51. START Condition/STOP Condition Detect Timing Diagram
Table 9. START Condition/STOP Condition Generation Timing Table Standard Clock Mode High-speed Clock Mode Item 5.0 s (20 cycles) Setup time 2.5 s (10 cycles) Hold time 5.0 s (20 cycles) 2.5 s (10 cycles) Set/reset time 3.0 s (12 cycles) 1.5 s (6 cycles) for BB flag Note: Absolute time at = 4 MHz. The value in parentheses denotes the number of cycles.
Table 10. START Condition/STOP Condition Detect Conditions High-speed Clock Mode Standard Clock Mode 1.0 s (4 cycles) < SCL 6.5 s (26 cycles) < SCL release time release time 3.25 s (13 cycles) < Setup time 0.5 s (2 cycles) < Setup time 3.25 s (13 cycles) < Hold time 0.5 s (2 cycles) < Hold time Note: Absolute time at = 4 MHz. The value in parentheses denotes the number of cycles.
49
MITSUBISHI MICROCOMPUTERS
. ion. hange c icat ecif ject to l sp fina re sub a not its a is is ntic lim : Th tice arame No e p Som
PRE
L
A IMIN
RY
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
(10) Address Data Communication
There are two address data communication formats, namely, 7-bit addressing format and 10-bit addressing format. The respective address communication formats is described below. 7-bit addressing format To meet the 7-bit addressing format, set the 10BIT SAD bit of the I2C control register (address 00F916) to "0." The first 7-bit address data transmitted from the master is compared with the high-order 7-bit slave address stored in the I2C address register (address 00F716). At the time of this comparison, address comparison of the RBW bit of the I2C address register (address 00F716) is not made. For the data transmission format when the 7-bit addressing format is selected, refer to Figure 52, (1) and (2). 10-bit addressing format To meet the 10-bit addressing format, set the 10BIT SAD bit of the I2C control register (address 00F916) to "1." An address comparison is made between the first-byte address data transmitted from the master and the 7-bit slave address stored in the I2C address register (address 00F716). At the time of this comparison, an address comparison between the RBW bit of the I2C address regis__ ter (address 00F716) and the R/W bit which is the last bit of the address data transmitted from the master is made. In the 10-bit __ addressing mode, the R/W bit which is the last bit of the address data not only specifies the direction of communication for control data but also is processed as an address data bit. When the first-byte address data matches the slave address, the AAS bit of the I2C status register (address 00F816) is set to "1." After the second-byte address data is stored into the I 2C data shift register (address 00F616), make an address comparison between the second-byte data and the slave address by software. When the address data of the 2nd bytes matches the slave address, set the RBW bit of software. This the I2C address register (address 00F716) to "1" by __ processing can match the 7-bit slave address and R/W data, which are received after a RESTART condition is detected, with the value of the I2C address register (address 00F716). For the data transmission format when the 10-bit addressing format is selected, refer to Figure 52, (3) and (4).
Set transmit data in the I2C data shift register (address 00F616). At this time, an SCL and an ACK clock automatically occurs. When transmitting control data of more than 1 byte, repeat step . Set "D016" in the I2C status register (address 00F816). After this, if ACK is not returned or transmission ends, a STOP condition will be generated.
(12) Example of Slave Reception
An example of slave reception in the high-speed clock mode, at the SCL frequency of 400 kHz, in the ACK non-return mode, using the addressing format, is shown below. Set a slave address in the high-order 7 bits of the I2C address register (address 00F716) and "0" in the RBW bit. Set the no ACK clock mode and SCL = 400 kHz by setting "2516" in the I2C clock control register (address 00FA16). Set "1016" in the I 2C status register (address 00F816) and hold the SCL at the HIGH. Set a communication enable status by setting "4816" in the I 2C control register (address 00F916). When a START condition is received, an address comparison is made. *When all transmitted addresses are "0" (general call) : AD0 of the I2C status register (address 00F816) is set to "1" and an interrupt request signal occurs. *When the transmitted addresses match the address set in : AAS of the I2C status register (address 00F816) is set to "1" and an interrupt request signal occurs. *In the cases other than the above : AD0 and AAS of the I2C status register (address 00F816) are set to "0" and no interrupt request signal occurs. Set dummy data in the I2C data shift register (address 00F616). When receiving control data of more than 1 byte, repeat step . When a STOP condition is detected, the communication ends.
(11) Example of Master Transmission
An example of master transmission in the standard clock mode, at the SCL frequency of 100 kHz and in the ACK return mode is shown below. Set a slave address in the high-order 7 bits of the I2C address register (address 00F716) and "0" in the RBW bit. Set the ACK return mode and SCL = 100 kHz by setting "8516" in the I 2C clock control register (address 00FA16). Set "1016" in the I2C status register (address 00F816) and hold the SCL at the HIGH. Set a communication enable status by setting "4816" in the I2C control register (address 00F916). Set the address data of the destination of transmission in the highorder 7 bits of the I2C data shift register (address 00F616) and set "0" in the least significant bit. Set "F016" in the I2C status register (address 00F816) to generate a START condition. At this time, an SCL for 1 byte and an ACK clock automatically occurs.
50
MITSUBISHI MICROCOMPUTERS
n. ange. atio h cific ct to c spe je inal re sub t a f its a o is n lim This entic m ice: Not e para Som
PRE
L
A IMIN
RY
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
S
Slave address R/W
A
Data
A
Data
A/A
P
7 bits "0" 1 to 8 bits 1 to 8 bits (1) A master-transmitter transmits data to a slave-receiver
S
Slave address R/W
A
Data
A
Data
A
P
7 bits "1" 1 to 8 bits 1 to 8 bits (2) A master-receiver receives data from a slave-transmitter Slave address R/W 1st 7 bits Slave address 2nd byte
S
A
A
Data
A
Data
A/A
P
1 to 8 bits 7 bits "0" 8 bits 1 to 8 bits (3) A master-transmitter transmits data to a slave-receiver with a 10-bit address Slave address R/W 1st 7 bits Slave address 2nd byte Slave address R/W 1st 7 bits
S
A
A
Sr
Data
A
Data 1 to 8 bits
A
P
7 bits "0" 8 bits 7 bits "1" 1 to 8 bits (4) A master-receiver receives data from a slave-transmitter with a 10-bit address S : START condition A : ACK bit Sr : Restart condition P : STOP condition R/W : Read/Write bit From master to slave From slave to master
Fig. 52. Address Data Communication Format
51
P
. e tion ang ifica t to ch pec c al s subje fin re a ot a is n limits This ntic ice: arame Not e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
OSD FUNCTIONS
Table 11 outlines the OSD functions of the M37271MF-XXXSP. The M37274MA-XXXSP incorporates an OSD circuit of 36 characters ! 12 lines. OSD is controlled by the OSD control register. There are 3 display modes and they are selected by a block unit. The display modes are selected by block control register i (i = 1 to 12). The features of each mode are described below.
Note : Note that EPROM version has 40 characters ! 16 lines when programming.
Table 11. Features of Each Display Mode Parameter Number of display characters Character display area Kinds of characters Kinds of character sizes Pre-divide ratio (Note) Dot size Attribute Character font coloring Raster coloring Character background coloring Border coloring Extra font coloring OSD output Function R, G, B, OUT1, OUT2 Auto solid space function Window function Dual layer OSD function (layer 1) Possible R, G, B, OUT1, OUT2 Dual layer OSD function (layer 2) CC Mode (Closed caption mode) 36 characters ! 12 lines Display Mode OSD Mode (On-screen display mode) 36 characters ! 12 lines EXOSD Mode (Extra on-screen display mode) 36 characters ! 12 lines
16 ! 26 dots 16 ! 20 dots 16 ! 26 dots (character dot structure : 20 ! 16 dots) 256 kinds (In EXOSD mode, they can be combined with 16 kinds of extra fonts) 14 kinds 6 kinds 2 kinds ! 1, ! 2 ! 1, ! 2, ! 3 ! 1, ! 2, ! 3 1TC ! 1/2H Smooth italic, under line, flash 1 screen : 7 kinds, Max. 7 kinds (a character unit) 1TC ! 1/2H, 1TC ! 1H, 1.5TC ! 1/2H, 1.5TC ! 1H, 2TC ! 2H, 3TC ! 3H Border 1 screen : 7 kinds, Max. 7 kinds (a character unit) 1TC ! 1/2H, 1TC ! 1H Border, extra font (16 kinds) 1 screen : 5 kinds, Max. 5 kinds (a character unit)
Possible (a screen unit, 1 screen : 7 Possible (a screen unit, 1 screen : Possible (a screen unit, 1 screen : kinds, max. 7 kinds) 7 kinds, max. 7 kinds) 7 kinds, max. 7 kinds) Possible (a character unit, 1 screen Possible (a character unit, 1 screen Possible (a character unit, 1 screen : : 7 kinds, max. 7 kinds) 7 kinds, max. 7 kinds) : 7 kinds, max. 7 kinds) Possible (a screen unit, 1 screen : Possible (a screen unit, 1 screen : 7 kinds, max. 7 kinds) 7 kinds, max. 7 kinds) Possible (a screen unit, 1 screen : 7 kinds, max. 7 kinds) R, G, B, OUT1, OUT2
Display expansion Possible Possible (multiline display) Notes 1: The divide ratio of the frequency divider (the pre-divide circuit) is referred as "pre-divide ratio" hereafter. 2: The character size is specified with dot size and pre-divide ratio (refer to (3) Dote size).
52
P
. ion. hange c icat ecif ject to l sp fina re sub ot a its a is n his entic lim e: T otic param N e Som
REL
A IMIN
RY
MITSUBISHI MICROCOMPUTERS
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
The OSD circuit has an extended display mode. This mode allows multiple lines (16 lines or more) to be displayed on the screen by interrupting the display each time one line is displayed and rewriting data in the block for which display is terminated by software. Figure 53 shows the configuration of OSD character. Figure 54 shows the block diagram of the OSD circuit. Figure 55 shows the structure of the OSD control register. Figure 56 shows the structure of the block control register.
CC mode OSD mode
16 dots 16 dots Blank area*
20 dots
26 dots 20 dots
Underline area* Blank area*
*
16 dots 16 dots
: Displayed only in CCD mode.
EXOSD mode
16 dots
20 dots
26 dots
logical sum (OR)
Character font
Extra font
Fig. 53. Configuration of OSD Character Display Area
26 dots
53
PR
e. n. atio chang cific to spe ubject al a fin re s not mits a li is is : Th mentic ice Not e para Som
IN LIM E
ARY
MITSUBISHI MICROCOMPUTERS
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
Main clock XIN XOUT
Clock for OSD OSC1 OSC2 HSYNC VSYNC
Oscillation circuit
Display oscillation circuit
Data slicer clock
Control registers for OSD OSD Control circuit OSD control register Horizontal position register Block control registers Clock source control register I/O polarity control register Raster color register Extra font color register Border color register Window H/L registers Vertical position registers RAM for OSD
20 bytes !36 characters !12 lines
(address 00CE16) (address 00CF16) (addresses 00D016 to 00DB16) (address 021616) (address 021716) (address 021816) (address 021916) (address 021B16) (addresses 021C16 to 021F16) (addresses 022016 to 023B16)
ROM for OSD
(16 dots ! 20 dots! 256 characters) + 16 dots ! 26 dots! 16 characters)
Shift register 1 16-bit Output circuit Shift register 2 16-bit
R
G
B
OUT1
OUT2
Data bus
Fig. 54. Block Diagram of OSD Circuit
54
P
. e. tion ang ifica t to ch pec c al s subje a fin are not its is is ntic lim : Th tice arame No e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
7
7 0
0 Block control register i (i = 1 to 12) (BCi : addresses 00D016 to 00BF) Display mode selection bits
b1 b0
OSD control register (OC : address 00CE16) OSD control bit (Note 1) 0 : All-blocks display off 1 : All-blocks display on Scan mode selection bit 0 : Normal scan mode 1 : Bi-scan mode Border type selection bit 0 : All bordered 1 : Shadow bordered (Note 2) Flash mode selection bit 0 : Color signal of character background part does not flash 1 : Color signal of character background part flashes Automatic solid space control bit 0 : OFF 1 : ON Window control bit 0 : OFF 1 : ON Layer mixing control bits (Note 3)
b7 b6
0 0 1 1
0 : Display OFF 1 : OSD mode 0 : CC mode 1 : EXOSD mode
Border control bit 0 : Border OFF 1 : Border ON Dot size selection bit Refer to Table 12. Pre-divide ratio * layer selection bits Refer to Table 12. OUT 2 output control bit (Note) 0 : OUT2 output OFF 1 : OUT2 output ON Notes 1: Bit RC 14 of OSD RAM controls OUT1 output when bit 7 is "0." Bit RC 14 of OSD RAM controls OUT2 output when bit 7 is "1." 2: Note that EPROM version the block control registers at addresses 00D0 16 to 00DF16 when programming.
0 0 : Logical sum (OR) of layer 1's color and layer 2's color 0 1 : Layer 1's color has priority 1 0 : Layer 2's color has priority 1 1 : Do not set Notes 1 : Even this bit is switched during display, the display screen remains unchanged until a rising (falling) of the next V SYNC. 2 : Shadow border is output at right and bottom side of the font. 3 : Set "00" during displaying extra fonts.
Fig. 56. Block Control Registers
Table 12. Setting Value of Block Control Registers b6 b5 b4 b3 CS6 Pre-divide Ratio Dot Size 1TC ! 1/2H -- !1 1TC ! 1H 2TC ! 2H 3TC ! 3H 1TC ! 1/2H -- !2 1TC ! 1H 2TC ! 2H 3TC ! 3H 1TC ! 1/2H -- !3 1TC ! 1H 2TC ! 2H 3TC ! 3H 0 !1 1TC ! 1/2H 1TC ! 1H 1TC ! 1/2H 1 !2 1TC ! 1H 1.5TC ! 1/2H 1.5TC ! 1H Layer 2 Layer 1 Display Layer
Fig. 55. OSD Control Register 0 0
0 0 1 1 0 0 1 1 0 0 1 1 -- -- 0 0 1 1
0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
0
1
1
0
1
1
1
1
Notes 1: CS6 : Bit 6 of clock control register (Address 021616) 2: TC : OSD clock cycle divided in the pre-divide circuit 3: H : HSYNC
55
P
. e tion ang ifica t to ch pec c al s subje fin re a ot a is n limits This ntic ice: arame Not e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
(1) Dual Layer OSD
M37274MA-XXXSP has 2 layers; layer 1 and layer 2. These layers display the OSD for controlling TV and the closed caption display at the same time and overlayed on each other. Each block can be assigned to either layer by bits 6 and 5 of the block control register (refer to Figure 56). For example, only when both bits 5 and 6 are "1," the block is assigned to layer 2. Other bit combinations assign the block to layer 1. When a block of layer 1 is overlapped with that of layer 2, a screen is combined (refer to Figure 58) by bits 7 and 6 of the OSD control register (refer to Figure 55). Note: When using the dual layer OSD, note Table 13.
Layer 2 Block 9 Block 10 Block 11 Block 12 Block Block 1 Block 2
Block 7 Block 8 Block Layer 1
...
Fig. 57. Image of Dual Layer OSD
Table 13. Conditions of Dual Layer Block Parameter Display mode OSD Clock source Pre-divide ratio Dot size Horizontal display start position Block in Layer 1 CC mode Data slicer clock or OSC1 or main clock ! 1 or ! 2 (all blocks) 1TC ! 1/2H Arbitrary Block in Layer 2 OSD mode Same as layer 1 Same as layer 1 (Note) Pre-divide ratio = 1 1TC ! 1/2H 1TC ! 1H Pre-divide ratio = 2 1TC ! 1/2H, 1.5TC ! 1/2H 1TC ! 1H, 1.5TC ! 1H
Same position as layer 1
Note: For the pre-divide ratio of the layer 2, select the same as the layer 1's ratio by bit 6 of the clock control register.
Display example of layer 1 = "HELLO," layer 2 = "CH5"
CH5 HELLO
CH5 HELLO
CH5 HELLO
Logical sum (OR) of layer 1's color and layer 2's color Bit 7 = "0," bit 6 = "0"
Layer 1's color has priority Bit 7 = "0", bit 6 = "1"
Layer 2's color has priority Bit 7 = "1," bit 6 = "0"
Fig. 58. Display Example of Dual Layer OSD
56
P
. e tion ang ifica t to ch pec c al s subje a fin are not its is is ntic lim : Th tice arame No e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
(2) Display Position
The display positions of characters are specified by a block. There are 12 blocks, blocks 1 to 12. Up to 36 characters can be displayed in each block (refer to (6) Memory for OSD). The display position of each block can be set in both horizontal and vertical directions by software. The display position in the horizontal direction can be selected for all blocks in common from 256-step display positions in units of 4 TOSC (TOSC = OSD oscillation cycle). The display position in the vertical direction for each block can be selected from 1024-step display positions in units of 1 TH ( TH = HSYNC cycle).
Blocks are displayed in conformance with the following rules: When the display position is overlapped with another block (Figure 59, (b)), a lower block number (1 to 12) is displayed on the front. When another block display position appears while one block is displayed (Figure 59 (c)), the block with a larger set value as the vertical display start position is displayed. However, do not display block with the dot size of 2TC ! 2H or 3TC ! 3H during display period ( V ) of another block. V In the case of OSD mode block: 20 dots in vertical from the vertical display start position. V In the case of CC or EXOSD mode block: 26 dots in vertical from the vertical display start position.
(HR) VP11, VP21 Block 1 VP12, VP22 Block 2 VP13, VP23 Block 3
(a) Example when each block is separated
(HR) VP11, VP12 = VP21, VP22 Block 1 (Block 2 is not displayed) (b) Example when block 2 overlaps with block 1
(HR) VP11, VP21 VP12, VP22 Block 1 Block 2 (c) Example when block 2 overlaps in process of block 1
Note: VP1i or VP2i (i : 1 to 12) indicates the vertical display start position of display block i.
Fig. 59. Display Position
57
P
. e. tion ang ifica t to ch pec c al s subje a fin are not its is is ntic lim : Th tice arame No e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
The display position in the vertical direction is determined by counting the horizontal sync signal (HSYNC). At this time, when VSYNC and HSYNC are positive polarity (negative polarity), it starts to count the rising edge (falling edge) of HSYNC signal from after fixed cycle of rising edge (falling edge) of VSYNC signal. So interval from rising edge (falling edge) of VSYNC signal to rising edge (falling edge) of HSYNC signal needs enough time (2 machine cycles or more) for avoiding jitter. The polarity of HSYNC and VSYNC signals can select with the I/O polarity control register (address 021716).
7
0
Vertical position register 1i (i = 1 to 12) (VP1i : addresses 022016 to 022B16) Control bits of vertical display start positions (Note) Vertical display start positions (low-order 8 bits) TH ! (setting value of low-order 2 bits of VP2i ! 16 2 + setting value of low-order 4 bits of VP1i ! 161 + setting value of low-order 4 bits of VP1i ! 160 )
7 0
8 machine cycles or more VSYNC signal input 0.25 to 0.50 [s] ( at f(XIN) = 8MHz) VSYNC control signal in microcomputer Period of counting HSYNC signal (Note 2) HSYNC signal input 8 machine cycles or more 1 2 3 4 5
Vertical position register 2i (i = 1 to 12) (VP2i : addresses 023016 to 023B16) Control bits of vertical display start positions (Note) Vertical display start positions (high-order 2 bits) TH ! (setting value of low-order 2 bits of VP2i ! 16 2 + setting value of low-order 4 bits of VP1i ! 16 1 + setting value of low-order 4 bits of VP1i ! 16 0 ) Note : Set values except "00 16" and "0116" to VP1i when VP2i is "00 16."
Not count When bits 0 and 1 of the I/O polarity control register (address 021716) are set to "1" (negative polarity) Notes 1 : The vertical position is determined by counting falling edge of HSYNC signal after rising edge of VSYNC control signal in the microcomputer. 2 : Do not generate falling edge of H SYNC signal near rising edge of VSYNC control signal in microcomputer to avoid jitter. 3 : The pulse width of VSYNC and HSYNC needs 8 machine cycles or more.
Fig. 61. Vertical Position Registers
The horizontal position is common to all blocks, and can be set in 256 steps (where 1 step is 4TOSC, TOSC being the oscillating cycle for display) as values "0016" to "FF16" in bits 0 to 7 of the horizontal position register (address 00CF16). The structure of the horizontal position register is shown in Figure 62.
Fig. 60. Supplement Explanation for Display Position
7 0
The vertical position for each block can be set in 1024 steps (where each step is 1TH (TH: HSYNC cycle)) as values "0016" to "FF16" in vertical position register 1i (i = 1 to 12) (addresses 022016 to 022B16) and values "0016" to "0316" in vertical position register 2i (i = 1 to 12) (addresses 023016 to 023B16). The structure of the vertical position registers is shown in Figure 61.
Horizontal position register (HP : address 00CF16)
Control bits of horizontal display start positions Horizontal display start positions 4TOSC ! (setting value of high-order 4 bits ! 161 +setting value of low-order 4 bits ! 160) Note : The setting value synchronizes with the V SYNC.
Fig. 62. Horizontal Position Register
58
P
. e tion ang ifica t to ch pec c al s subje a fin are not its is is ntic lim : Th tice arame No e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
Notes 1 : 1TC (TC : OSD clock cycle divided by prescaler) gap occurs between the horizontal display start position set by the horizontal position register and the most left dot of the 1st block. Accordingly, when 2 blocks have different predivide ratios, their horizontal display start position will not match. Ordinaly, this gap is 1TC regardless of character sizes, however, the gap is 1.5TC only when the character size is 1.5TC.
2 : The horizontal start position is based on the OSD clock source cycle selected for each block. Accordingly, when 2 blocks have different OSD clock source cycles, their horizontal display start position will not match.
HSYNC 1TC
Block 1 (Pre-divide ratio = 1, clock source = data slicer clock)
Note 1
4TOSC ! N
1TC
Block 2 (Pre-divide ratio = 2, clock source = data slicer clock)
1TC
Block 3 (Pre-divide ratio = 3, clock source = data slicer clock)
1.5TC
Block 4 (Pre-divide ratio = 2, character size = 1.5Tc, clock source = data slicer clock)
Note 2
4TOSC' ! N
1TC
Block 5 (Pre-divide ratio = 3, clock source = OSC1) N 1Tc Tosc Tdef : Value of horizontal position register (decimal notation) : OSD clock cycle divided in the pre-divide circuit : OSD oscillation cycle : 62 Tosc
Fig. 63. Notes on Horizontal Display Start Position
59
P
. e tion ang ifica t to ch pec c al s subje fin re a ot a is n limits This ntic ice: arame Not e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
(3) Dot Size
The dot size can be selected by a block unit. The dot size in vertical direction is determined by dividing HSYNC in the vertical dot size control circuit. The dot size in horizontal is determined by dividing the following clock in the horizontal dot size control circuit : the clock gained by dividing the OSD clock source (data slicer clock, OSC1, main clock) in the pre-divide circuit. The clock cycle divided in the pre-divide circuit is defined as 1TC. The dot size of the layer 1 is specified by bits 6 to 3 of the block control register. The dot size of the layer 2 is specified by the following bits : bits 3 and 4 of the block control register, bit 6 of the clock source control register. Refer to Figure 56 (the structure of the block control regis-
ter), refer to Figure 65 (the structure of the clock source control register). The block diagram of dot size control circuit is shown in Figure 64. Notes 1 : The pre-divide ratio = 3 cannot be used in the CC mode. 2 : The pre-divide ratio of the OSD mode block on the layer 2 must be same as that of the CC mode block on the layer 1 by bit 6 of the clock source control register. 3 : In the bi-scan mode, the dot size in the vertical direction is 2 times as compared with the normal mode. Refer to "(13) Scan Mode" about the scan mode.
Main clock OSC1 Data slicer clock (Note)
Synchronous
circuit
Clock cycle = 1TC
Cycle!2 Cycle!3
Horizontal dot size control circuit
Pre-divide circuit HSYNC Vertical dot size control circuit
OSD control circuit Note: To use data slicer clock, set bit 0 of data slicer control register to "0."
Fig. 64. Block Diagram of Dot Size Control Circuit
1 dot
1TC 1/2H 1H
1TC
2TC
3TC Scanning line of F1(F2) Scanning line of F2(F1) 3H
2H
Fig. 65. Definition of Dot Sizes
60
P
. e tion ang ifica t to ch pec c al s subje fin re a ot a is n limits This ntic ice: arame Not e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
(4) Clock for OSD
As a clock for display to be used for OSD, it is possible to select one of the following 4 types. Main clock (8 MHz) Data slicer clock output from the data slicer (approximately 26 MHz) Clock from the LC oscillator supplied from the pins OSC1 and OSC2 Clock from the ceramic resonator or the quartz-crystal oscillator from the pins OSC1 and OSC2 This OSD clock for each block can be selected by the following bits : bit 7 of the port P3 direction register, bits 5 and 4 of the clock source control register (addresses 021616). A variety of character sizes can be obtained by combining dot sizes with OSD clocks. When not using the pins OSC1 and OSC2 for the OSD clock I/O pins, the pins can be used as sub-clock I/O pins or port P6.
7 0
* * * *
Clock source control register (CS : address 021616)
CC mode clock selection bit 0 : Data slicer clock 1 : OSC1 clock OSD mode clock selection bits
b2 b1
0 0 1 1
0 : Data slicer clock 1 : OSC1 clock 0 : Main clock (Note 1) 1 : Do not set
Table 14. Setting for P63/OSC1/XCIN, P64/OSC2/XCOUT Sub-clock Input OSD Clock Function I/O Pin Port I/O Pin Register b7 of port P3 direction register Clock source control register b5 b4 1 0 1 1 0 0 0 1 0 0 1
EXOSD mode clock selection bit 0 : Data slicer clock 1 : OSC1 clock OSD1 oscillating mode selection bits
b5 b4
0 0 1 1
0 : 32 kHZ oscillating mode 1 : Input ports P63, P64 0 : LC oscillating mode 1 : Ceramic * quartz-crystal oscillating mode
Pre-divide ratio of layer 2 selection bit 0:!1 1:!2 Test bit (Note 2) Notes 1: When setting "102," main clock is set as a clock in the CC mode and EXOSD mode regardless of bits 0, 3. 2: Be sure to set bit 7 to "0" for program of the mask and the EPROM versions. For the emulator MCU version (M37274ERSS), be sure to set bit 7 to "1" when using the data slicer clock for software debugging.
Fig. 66. Clock Control Register
Data slicer circuit 32 kHZ
"00"
(Note) Data slicer clock
"0" Except "10" "1" "0"
CS0
"10"
CC mode block CS2, CS1
Except "10"
OSC1 clock LC
Ceramic * quartz-crystal "10"
"1" "0"
CS1 CS2 = "0"
OSD mode block CS2, CS1
Except "10"
CS5, CS4
"11"
"1"
CS3
"10"
EXOSD mode block CS2, CS1
Oscillating mode for OSD Clock oscillation circuit
Main clock
Note : To use data slicer clock, set bit 0 of data slicer control register to "1."
Fig. 67. Block Diagram of OSD Selection Circuit
61
P
. e tion ang ifica t to ch pec c al s subje fin re a ot a is n limits This ntic ice: arame Not e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
(5) Field Determination Display
To display the block with vertical dot size of 1/2H, whether an even field or an odd field is determined through differences in a synchronizing signal waveform of interlacing system. The dot line 0 or 1 (refer to Figure 69) corresponding to the field is displayed alternately. In the following, the field determination standard for the case where both the horizontal sync signal and the vertical sync signal are negative-polarity inputs will be explained. A field determination is determined by detecting the time from a falling edge of the horizontal sync signal until a falling edge of the VSYNC control signal (refer to Figure 60) in the microcomputer and then comparing this time with the time of the previous field. When the time is longer than the comparing time, it is regarded as even field. When the time is shorter, it is regarded as odd field The contents of this field can be read out by the field determination flag (bit 7 of the I/O polarity control register at address 021716). A dot line is specified by bit 6 of the I/O polarity control register (refer to Figure 69). However, the field determination flag read out from the CPU is fixed to "0" at even field or "1" at odd field, regardless of bit 6.
7 0 I/O polarity control register (PC : address 021716) HSYNC input polarity switch bit 0 : Positive polarity input 1 : Negative polarity input
VSYNC input polarity switch bit 0 : Positive polarity input 1 : Negative polarity input R/G/B output polarity switch bit 0 : Positive polarity output 1 : Negative polarity output
OUT1 output polarity switch bit 0 : Positive polarity output 1 : Negative polarity output OUT2 output polarity switch bit 0 : Positive polarity output 1 : Negative polarity output Display dot line selection bit (Note) 0: " " at even field " " at odd field 1: " " at even field " " at odd field Field determination flag 0 : Even field 1 : Odd field
Note : Refer to Figure 69.
Fig. 68. I/O Polarity Control Register
62
P
. ion. hange c icat ecif ject to l sp fina re sub a not its a is is ntic lim : Th tice arame No e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
Both HSYNC signal and VSYNC signal are negative-polarity input Field Display dot line determination selection bit flag(Note)
HSYNC
Field
Display dot line
VSYNC and VSYNC control signal in microcomputer Upper : VSYNC signal Lower : VSYNC control signal in microcomputer
(n - 1) field (Odd-numbered) T1
0.25 to 0.50[s] at f(XIN) = 8 MHz
Odd
0 (n) field (Even-numbered) T2 Even 0 (T2 > T1) 1
Dot line 1 Dot line 0
0 (n + 1) field (Odd-numbered) T3 Odd 1 (T3 < T2) 1
16)
Dot line 0
Dot line 1 to "0."
When using the field determination flag, be sure to set bit 0 of the PWM mode register 1 (address 020A 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 CC mode * EXOSD mode 2345 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 OSD mode 12 345
6 7 8 9 10 11 12 13 14 15 16
When the display dot line selection bit is "0," the " " font is displayed at even field, the " " font is displayed at odd field. Bit 7 of the I/O polarity control register can be read as the field determination flag : "1" is read at odd field, "0" is read at even field.
OSD ROM font configuration diagram
Note : The field determination flag changes at a rising edge of the V SYNC control signal (negative-polarity input) in the microcomputer.
Fig. 69. Relation between Field Determination Flag and Display Font
63
P
. e. tion ang ifica t to ch pec c al s subje a fin are not its is is ntic lim : Th tice arame No e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
(6) Memory for OSD
There are 2 types of memory for OSD : ROM for OSD (addresses 1080016 to 155FF16, 1800016 to 1E41F16) used to store character dot data (masked) and RAM for OSD (addresses 080016 to 0DF316) used to specify the characters and colors to be displayed. The following describes each type of memory. ROM for OSD (addresses 1080016 to 155FF16, 1800016 to 1E43F16) The ROM for OSD contains dot pattern data for characters to be displayed. To actually display the character code and the extra code stored in this ROM, it is necessary to specify them by writing the character code inherent to each character (code determined based on the addresses in the ROM for OSD) into the RAM for OSD.
The OSD ROM of the character font has a capacity of 11072 bytes. Since 40 bytes are required for 1 character data, the ROM can stores up to 256 kinds of characters. The OSD ROM of the extra font has a capacity of 832 bytes. Since 52 bytes are required for 1 character data, the ROM can stores up to 16 kinds of characters. Data of the character font and extra font is specified shown in Figure 70.
OSD ROM address of character font data
OSD ROM address bit AD16 AD15 AD14 AD13 AD12 AD11 AD10 AD9 AD8 AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0 Font bit
Line number/character code/font bit Line number Character code Font bit
1
0
Line number
0
Character code
= "0216" to "1516" = "0016" to "13F16" = 0 : left font 1 : right font
OSD ROM address of extra font data
OSD ROM address bit AD16 AD15 AD14 AD13 AD12 AD11 AD10 AD9 AD8 AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0 Font bit
Line number/extra code /font bit Line number Extra code Font bit Line number
0216 0316 0416 0516 0616 0716 0816 0916 0A16 0B16 0C16 0D16 0E16 0F16 1016 1116 1216 1316 1416 1516
1
1
Line number
0
0
0
0
0
Extra code
= "0016" to "1916" = "0016" to "1F16" = 0 : left font 1 : right font Left font Right font Data in Line OSD number ROM
000016 7FF016 7FF816 601C16 600C16 600C16 600C16 600C16 601C16 7FF816 7FF016 630016 638016 61C016 60E016 607016 603816 601C16 600C16 000016 0016 0116 0216 0316 0416 0516 0616 0716 0816 0916 0A16 0B16 0C16 0D16 0E16 0F16 1016 1116 1216 1316 1416 1516 1616 1716 1816 1916
b7
b7
b0 b7
b0
Left font
b0 b7
Right font
b0
Data in OSD ROM
FFFE16 FFFF16 000316 000316 000316 000316 000316 000316 000316 000316 000316 000316 000316 000316 000316 000316 000316 000316 000316 000316 000316 000316 FFFF16 FFFE16 000016 000016
Character font
Extra font
Fig. 70. OSD Character Data Storing Form
64
P
. e tion ang ifica t to ch pec c al s subje a fin are not its is is ntic lim : Th tice arame No e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
2 RAM for OSD (addresses 080016 to 0DF316) The RAM for OSD is allocated at addresses 080016 to 0DF316, and is divided into a display character code specification part, color code 1 specification part, and color code 2 specification part for each block. Table 15 shows the contents of the RAM for OSD. For example, to display 1 character position (the left edge) in block 1, write the character code in address 080016, write color code 1 at 084016, and write color code 2 at 082816. The structure of the RAM for OSD is shown in Figure 72.
Note: For the OSD mode block with dot size of 1.5TC ! 1/2H and 1.5TC ! 1H, the 3nth (n = 1 to 13) character is skipped as compared with ordinary blockV. Accordingly, maximum 24 characters are only displayed in 1 block. The RAM data for the 3nth character does not effect the display. Any character data can be stored here (refer to Figure 71). Note that EPROM version has maximum 27 characters (The right 1/3 part of the 27th's character area is not displayed.) in 1 block when programming. V Blocks with dot size of 1TC ! 1/2H and 1TC ! 1H, or blocks on the layer 1
Table 15. Contents of OSD RAM Block Display Position (from left) 1st character 2nd character : 24th character 25th character : 35th character 36th character 1st character 2nd character : 24th character 25th character : 35th character 36th character 1st character 2nd character : 24th character 25th character : 35th character 36th character 1st character 2nd character : 24th character 25th character : 35th character 36th character 1st character 2nd character : 24th character 25th character : 35th character 36th character Character Code Specification 080016 080116 : 081716 081816 : 082216 082316 088016 088116 : 089716 0E9816 : 08A216 08A316 090016 090116 : 091716 091816 : 092216 092316 098016 098116 : 099716 099816 : 09A216 09A316 0A0016 0A0116 : 0A1716 0A1816 : 0A2216 0A2316 Color Code 1 Specification 084016 084116 : 085716 085816 : 086216 086316 08C016 08C116 : 08D716 08D816 : 08E216 08E316 094016 094116 : 095716 095816 : 096216 096316 09C016 09C116 : 09D716 08D816 : 09E216 09E316 0A4016 0A4116 : 0A5716 0A5816 : 0A6216 0A6316 Color Code 2 Specification 082816 082916 : 083F16 086816 : 087216 087316 08A816 08A916 : 08BF16 08E816 : 08F216 08F316 092816 092916 : 093F16 096816 : 097216 097316 09A816 09A916 : 09BF16 09E816 : 09F216 09F316 0A2816 0A2916 : 0A3F16 0A6816 : 0A7216 0A7316
Block 1
Block 2
Block 3
Block 4
Block 5
65
P
. e tion ang ifica t to ch pec c al s subje fin re a ot a is n limits This ntic ice: arame Not e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
Table 15. Contents of OSD RAM (continued) Block Display Position (from left) 1st character 2nd character : 24th character 25th character : 35th character 36th character 1st character 2nd character : 24th character 25th character : 35th character 36th character 1st character 2nd character : 24th character 25th character : 35th character 36th character 1st character 2nd character : 24th character 25th character : 35th character 36th character 1st character 2nd character : 24th character 25th character : 35th character 36th character 1st character 2nd character : 24th character 25th character : 35th character 36th character 1st character 2nd character : 24th character 25th character : 35th character 36th character Character Code Specification 0A8016 0A8116 : 0A9716 0A9816 : 0AA216 0AA316 0B0016 0B0116 : 0B1716 0B1816 : 0B2216 0B2316 0B8016 0B8116 : 0B9716 0B9816 : 0BA216 0BA316 0C0016 0C0116 : 0C1716 0C1816 : 0C2216 0C2316 0C8016 0C8116 : 0C9716 0C9816 : 0CA216 0CA316 0D0016 0D0116 : 0D1716 0D1816 : 0D2216 0D2316 0D8016 0D8116 : 0D9716 0D9816 : 0DA216 0DA316 Color Code 1 Specification 0AC016 0AC116 : 0AD716 0AD816 : 0AE216 0AE316 0B4016 0B4116 : 0B5716 0B5816 : 0B6216 0B6316 0BC016 0BC116 : 0BD716 0BD816 : 0BE216 0BE316 0C4016 0C4116 : 0C5716 0C5816 : 0C6216 0C6316 0CC016 0CC116 : 0CD716 0CD816 : 0CE216 0CE316 0D4016 0D4116 : 0D5716 0D5816 : 0D6216 0D6316 0DC016 0DC116 : 0DD716 0DD816 : 0DE216 0DE316 Color Code 2 Specification 0AA816 0AA916 : 0ABF16 0AE816 : 0AF216 0AF316 0B2816 0B2916 : 0B3F16 0B6816 : 0B7216 0B7316 0BA816 0BA916 : 0BBF16 0BE816 : 0BF216 0BF316 0C2816 0C2916 : 0C3F16 0C6816 : 0C7216 0C7316 0CA816 0CA916 : 0CBF16 0CE816 : 0CF216 0CF316 0D2816 0D2916 : 0D3F16 0D6816 : 0D7216 0D7316 0DA816 0DA916 : 0DBF16 0DE816 : 0DF216 0DF316
Block 6
Block 7
Block 8
Block 9
Block 10
Block 11
Block 12
66
P
. e tion ang ifica t to ch pec c al s subje fin re a ot a is n limits This ntic ice: arame Not e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
Display sequence RAM address order Display sequence RAM address order
1 1
2 2
3 4
4 5
5 7
6 8
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
1.5Tc size block
10 11 13 14 16 17 19 20 22 23 25 26 28 29 31 32 34 35
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 2425 26 27 28 29 30 31 32 33 34 35 36
1Tc size block
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 2122 23 24 25 26 27 28 29 30 31 32 33 34 35 36
Fig. 71. RAM Data for 3nth Character
Note: Do not read from and write to addresses shown in Table 16.
Table 16. List of Access Disable Addresses 087816 08F816 097816 09F816 0A7816 0AF816 0B7816 0BF816 0C7816 0CF816 0D7816 0DF816 0E7816 0EF816 0F7816 0FF816 087916 08F916 097916 09F916 0A7916 0AF916 0B7916 0BF916 0C7916 0CF916 0D7916 0DF916 0E7916 0EF916 0F7916 0FF916 087A16 08FA16 097A16 09FA16 0A7A16 0AFA16 0B7A16 0BFA16 0C7A16 0CFA16 0D7A16 0DFA16 0E7A16 0EFA16 0F7A16 0FFA16
67
P
. e tion ang ifica t to ch pec c al s subje fin re a ot a is n limits This ntic ice: arame Not e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
Blocks 1 to16 b7 RF7 RF6 RF5 RF4 RF3 RF2 b0 b7 b0 b3 b0
RF1 RF0 RC17 RC16 RC15 RC14 RC13 RC12 RC11 RC10 RC23 RC22 RC21 RC20
Character code
Color code 1
Color code 2
CC mode Bit RF0 RF1 RF2 RF3 RF4 RF5 RF6 RF7 RC10 RC11 RC12 RC13 RC14 RC15 RC16 RC17 RC20 RC21 RC22 RC23 Not used Not used 0 Control of character color R Control of character color G Control of character color B OUT1 control Flash control Underline control Italic control Control of background color R Control of background color G Control of background color B 0: Character output 1: Background output 0: Flash OFF 1: Flash ON 0: Underline OFF 1: Underline ON 0: Italic OFF 1: Italic ON Not used
0: Color signal output OFF 1: Color signal output ON
OSD mode Function Bit name Function
EXOSD mode Bit name Function
Bit name
Character code (Low-order 8 bits)
Specification of character code in OSD ROM
Character code (Low-order 8 bits)
Specification of character code in OSD ROM
Character code (Low-order 8 bits)
Specification of character code in OSD ROM
0 Control of character color R Control of character color G Control of character color B OUT1 control 0: Character output 1: Background output
0: Color signal output OFF 1: Color signal output ON
0 Character color code 0 (CC0) Character color code 1 (CC1) Character color code 2 (CC2) OUT1 control Extra code 0 Extra code 1 (EX1) Extra code 2 (EX2)
0: Color signal output OFF Background color code 0 1: Color signal output ON
Specification of character color
0: Character output 1: Background output Specification of ROM
(EX0) extra code in OSD
0: Color signal output OFF Control of background 1: Color signal output ON
Specification of
color R Control of background color G Control of background color B
(BCC0) background color Background color code 1 (BCC1) Background color code 2 (BCC2) Extra code 3 Specification of ROM (EX3) extra code in OSD
Notes 1: Read value of bits 4 to 7 of the color code 2 is undefined. 2: For "not used" bits, the write value is read. 3: Set "0" to RC10.
Fig. 72. Structure of OSD RAM
68
P
. e tion ang ifica t to ch pec c al s subje fin re a ot a is n limits This ntic ice: arame Not e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
(7) Character color
The color for each character is displayed by the color code 1. The kinds and specification method of character color are different depending on each mode. CC mode .................. 7 kinds Specified by bits 1 (R), 2 (G), and 3 (B) of color code 1 OSD mode ............... 7 kinds Specified by bits 1 (R), 2 (G) and 3 (B)of color code 1 EXOSD mode .......... 5 kinds Specified by bits 1 (CC0), 2 (CC1), and 3 (CC2) of color code 1 The correspondence Table of color code 1 and color signal output in the EXOSD mode is shown in Table 17.
Table 17. Correspondence Table of Color Code 1 and Color Signal Output in EXOSD Mode Color Code 1 Bit 3 CC2 0 0 0 0 1 1 1 1 Bit 2 CC1 0 0 1 1 0 0 1 1 Bit 1 CC0 0 1 0 1 0 1 0 1 0 1 0 1 1 1 0 1 0 0 1 1 1 1 1 1 0 0 0 0 0 1 1 1 R Color Signal Output G B
* * *
(8) Character background color
The character background color can be displayed in the character display area. The character background color for each character is specified by color code 2. The kinds and specification method of character background color are different depending on each mode. CC mode .................. 7 kinds Specified by bits 0 (R), 1 (G), and 2 (B) of color code 2 OSD mode ............... 7 kinds Specified by bits 0 (R), 1 (G), and 2 (B) of color code 2 EXOSD mode .......... 5 kinds Specified by bits 0 (BCC0), 1 (BCC1), and 2 (BCC2) of color code 2 The correspondence table of the color code 2 and color signal output in the EXOSD mode is shown in Table 18.
* * *
Table 18. Correspondence Table of Color Code 2 and Color Signal Output in EXOSD Mode Color Code 2 Bit 2 BCC2 0 0 0 0 1 1 1 1 Bit 1 BCC1 0 0 1 1 0 0 1 1 Bit 0 BCC0 0 1 0 1 0 1 0 1 R 0 1 0 1 1 1 0 1 Color Signal Output G 0 0 1 1 1 1 1 1 B 0 0 0 0 0 1 1 1
Note : The character background color is displayed in the following part : (character display area)-(character font)-(border)-(extra font). Accordingly, the character background color does not mix with these color signal.
69
P
. e tion ang ifica t to ch pec c al s subje fin re a ot a is n limits This ntic ice: arame Not e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
(9) OUT1, OUT2 signals
The OUT1, OUT2 signals are used to control the luminance of the video signal. The output waveform of the OUT1, OUT2 signals is controlled by bit 4 of color code 1 (refer to Figure 72), bits 2 and 7 of
the block control register (refer to Figure 56). The setting values for controlling OUT1, OUT2 and the corresponding output waveform is shown in Figure 73.
Block control register OUT2 output control bit (b7) Border output control bit (b2)
OUT1 control (b4 of color code 1)
Output waveform
0 0 1 0 0 1 1
OUT1 OUT2 OUT1 OUT2 OUT1 OUT2 OUT1 OUT2
0 0 1 1 0 1
OUT1 OUT2 OUT1 OUT2 OUT1 OUT2 OUT1
1
OUT2
Fig. 73. Setting Value for Controlling OUT1, OUT2 and Corresponding Output Waveform
70
P
. e. tion ang ifica t to ch pec al s subjec a fin are not its is is tic lim n : Th tice arame No e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
(10) Attribute
The attributes (flash, underline, italic) are controlled to the character font. The attributes for each character are specified by the color codes 1 and 2 (refer to Figure 71). The attributes to be controlled are different depending on each mode. CC mode ..................... Flash, underline, italic OSD mode .................. Border (all bordered, shadow bordered can be selected) EXOSD mode ............. Border (all bordered, shadow bordered can be selected) , extra font (16 kinds) Under line The underline is output at the 23th and 24th dots in vertical direction only in the CC mode. The underline is controlled by bit 6 of color code 1. The color of underline is the same color as that of the character font. Flash The parts of the character font, the underline, and the character background are flashed only in the CC mode. The color signals (R, G, B, OUT1) of the character font and the underline are controlled by bit 5 of color code 1. All of the color signals for the character font flash. However, the color signal for the character background can be controlled by bit 3 of the OSD control register (refer to Figure 52). The flash cycle bases on the VSYNC count. * VSYNC cycle ! 48 800 ms (at flash ON) * VSYNC cycle ! 16 267 ms (at flash OFF) Italic The italic is made by slanting the font stored in OSD ROM to the right only in the CC mode. The italic is controlled by bit 7 of color code 1. The display example of the italic and underline is shown in Figure 75. In this case, "R" is displayed. Notes 1: When setting both the italic and the flash, the italic character flashes. 2: When the pre-divide ratio = 1, the italic character with slant of 1 dot ! 5 steps is displayed (refer to Figure 74 (c)). When the pre-divide ratio = 2, the italic character with slant of 1/2 dot ! 10 steps is displayed (refer to Figure 74 (d)). 3: The boundary of character color is displayed in italic. However, the boundary of character background color is not affected by the italic (refer to Figure 75). 4: The adjacent character (one side or both side) to an italic character is displayed in italic even when the character is not specified to display in italic (refer to Figure 75). 5: When displaying the italic character in the block with the pre-divide ratio = 1, set the OSD clock frequency to 11 MHz to 14 MHz.
71
P
. e tion ang ifica t to ch pec c al s subje fin re a ot a is n limits This ntic ice: arame Not e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
Color code 1
Color code 1
Bit 6
Bit 7
Bit 6
Bit 7
0
0
1
0
(a) Ordinary
(b) Underline
Color code 1 Bit 6 Bit 7
Color code 1
Bit 6
Bit 7
0
1
0
1
(c) Italic (pre-divide ratio = 1)
(d) Italic (pre-divide ratio = 2)
Fig. 74. Example of Attribute Display (in CC mode)
Italic on one side
Italic on both sides
Bit 7 of color code 1
1
0
0
1
1
0
1
Note : The wavy-lined is the boundary of character color
Fig. 75. Example of Italic Display
72
P
. e. tion ang ifica t to ch pec c al s subje a fin are not its is is ntic lim : Th tice arame No e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
Extra font There are 16 kinds of the extra fonts configured with 16 26 dots in OSD ROM. This 16 kinds fonts can be displayed by ORed with the character font by a character unit (refer to Figure 53). In only the EXOSD mode, the extra font is controlled the following : bits 7 to 5 of the color code 1 and bit 3 of the color code 2. The extra font color for each screen is specified by the extra color register. When the character font overlaps with the extra font, the color of the area becomes the ORed color of both fonts. Notes 1 : When using the extra font, set bits 7 and 6 of the OSD control register to "0" (refer to Figure 55). 2 : Extra fonts are always displayed by ORed with the character font. Accordingly, when displaying only a extra font, set a blank for a character font and OR with it.
7 0 0
0 Extra font color register (EC : address 021916) Extra font color R control bit 0 : No output 1 : Output Extra font color G control bit 0 : No output 1 : Output Extra font color B control bit 0 : No output 1 : Output Fix these bits to "0."
Fig. 76. Extra Font Color Register
16 dots 16 dots
16 dots
20 dots
Blank character font
Fig. 77. Display Example of Only Extra Font
26 dots
Extra font specified by EX0 to EX3
26 dots
+ (OR)
73
P
. e. tion ang ifica t to ch pec c al s subje a fin are not its is is ntic lim : Th tice arame No e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
Border The border is output in the OSD mode and the EXOSD mode. The all bordered (bordering around of character font) and the shadow bordered (bordering right and bottom sides of character font) are selected (refer to Figure 77) by bit 2 of the OSD control register (refer to Figure 55). The border ON/OFF is controlled by bit 2 of the block control register (refer to Figure 56). The OUT1 signal is used for border output. The border color for each screen is specified by the border color register. The horizontal size (x) of border is 1TC (OSD clock cycle divided in the pre-divide circuit) regardless of the character font dot size. However, only when the pre-divide ratio = 2 and character size = 1.5TC, the horizontal size is 1.5TC. The vertical size (y) different depending on the screen scan mode and the vertical dot size of character font.
Notes 1 : There is no border for the extra font. 2 : The border dot area is the shaded area as shown in Figure 79. In the EXOSD mode, top and bottom of character font display area is not bordered. 3 : When the border dot overlaps on the next character font, the character font has priority (refer to Figure 80 A). When the border dot overlaps on the next character back ground, the border has priority (refer to Figure 80 B). 4 : The border is not displayed at right side of the most right dot in the display area of the 36th character (the character located at the most right of the block). However, note that EPROM version can display the border above when programming. (The border for the right edge dots of the 40th's character area is not displayed.)
All bordered
Fig. 78. Example of Border Display
Shadow bordered
y
x
Scan mode Border dot size Vertical dot size of character font Horizontal size (x) Vertical size (y) Normal scan mode Bi-scan mode
1/2H
1H, 2H, 3H
1/2H, 1H, 2H, 3H
1TC (OSD clock cycle divided in pre-divide circuit) 1.5TC when selecting 1.5TC for character size.
1/2H
1H
1H
Fig. 79. Horizontal and Vertical Size of Border
74
P
. e tion ang ifica t to ch pec c al s subje a fin are not its is is ntic lim : Th tice arame No e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
OSD mode
EXOSD mode
16 dots
16 dots
Character font area
20 dots
Character font area
20 dots
1 dot width of border
1 dot width of border 1 dot width of border 1 dot width of border
Fig. 80. Border Area
7 0 0
0 Border color register (FC : address 021B16)
Border color R control bit 0 : No output 1 : Output Border color G control bit 0 : No output 1 : Output Border color B control bit 0 : No output 1 : Output Fix these bits to "0."
Character boundary B
Character boundary A
Character boundary B
Fig. 81. Border Priority
Fig. 82. Border Color Register
75
P
. e tion ang ifica t to ch pec c al s subje fin re a ot a is n limits This ntic ice: arame Not e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
(11) Multiline Display
The M37274MA-XXXSP can ordinarily display 16 lines on the CRT screen by displaying 16 blocks at different vertical positions. In addition, it can display up to 12 lines by using OSD interrupts. An OSD interrupt request occurs at the point at which display of each block has been completed. In other words, when a scanning line reaches the point of the display position (specified by the vertical position registers) of a certain block, the character display of that block starts, and an interrupt occurs at the point at which the scanning line exceeds the block. The mode in which an OSD interrupt occurs is different depending on the setting of the raster color register (refer to Figure 89). * When bit 7 of the raster color register is "0" An OSD interrupt occurs at the end of block display in the OSD and the EXOSD mode. * When bit 7 of the raster color register is "1" An OSD interrupt occurs at the end of block display in the CC mode.
Notes 1: An OSD interrupt does not occur at the end of display when the block is not displayed. In other words, if a block is set to off display by the display control bit of the block control register (addresses 00D016 to 00DB16), an OSD interrupt request does not occur (refer to Figure 83 (A)). 2: When another block display appeares while one block is displayed, an OSD interrupt request occurs only once at the end of the another block display (refer to Figure 83 (B)). 3: On the screen setting window, an OSD interrupt occurs even at the end of the CC mode block (off display) out of window (refer to Figure 83 (C)).
Block 1 (on display) Block 2 (on display) Block 3 (on display) Block 4 (on display)
"OSD interrupt request" "OSD interrupt request" "OSD interrupt request" "OSD interrupt request"
Block 1 (on display) Block 2 (on display) Block 3 (off display) Block 4 (off display)
"OSD interrupt request" "OSD interrupt request" No "OSD interrupt request" No "OSD interrupt request"
On display (OSD interrupt request occurs at the end of block display) (A)
Off display (OSD interrupt request does not occur at the end of block display)
Block 1 "OSD interrupt request" Block 1 Block 2
No "OSD interrupt request" "OSD interrupt request"
Block 2 "OSD interrupt request" Block 3 "OSD interrupt request"
Window In CC mode (B) (C)
Fig. 83. Note on Occurence of OSD Interrupt
76
P
. e tion ang ifica t to ch pec c al s subje fin re a ot a is n limits This ntic ice: arame Not e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
(12) Automatic Solid Space Function
This function generates automatically the solid space (OUT1 or OUT2 blank output) of the character area in the CC mode. The solid space is output in the following area : * the character area except character code "0916 " * the character area on the left and right sides This function is turned on and off by bit 4 of the OSD control register (refer to Figure 55).
Note : When using this function, set "0916" to the character below : * The 1st character * The 34th character and the following character.
Table 19. Setting for Automatic Solid Space Bit 4 of OSD control register Bit 7 of block control register Bit 4 of color code 1 OUT1 output signal 0 Character font part OUT2 output signal OFF 0 1 Character display area OFF Character display area OFF Solid space 0 Character font part 0 1 1 0 Solid space 0 1 0 Character font part 1 1 1
When setting the character code "05 16" as the character A, "06 16" as the character B.
(OSD RAM) Character to be displayed
09 05 09 09 09 06 06
16 16 16 16 16 16 16
***
06 09 09 09
16 16 16 16
(Display screen)
***
1st 2nd 3rd character character character
No blank output
34th 35th 36th character character character
(See note 1)
(See note 1)
Fig. 84. Display Screen Example of Automatic Solid Space
77
P
. e tion ang ifica t to ch pec c al s subje fin re a ot a is n limits This ntic ice: arame Not e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
(13) Scan Mode
M37271MF-XXXSP has the bi-scan mode for corresponding to HSYNC of double speed frequency. In the bi-scan mode, the vertical start display position and the vertical size is two times as compared with the normal scan mode. The scan mode is selected by bit 1 of the OSD control register (refer to Figure 55).
Table 20. Setting for Scan Mode Parameter Bit 1 of OSD control register Vertical display start position Vertical dot size Scan Mode Normal Scan 0 Value of vertical position register ! 1H 1TC ! 1/2H 1TC ! 1H 2TC ! 2H 3TC ! 3H Bi-Scan 1 Value of vertical position register ! 2H 1TC ! 1H 1TC ! 2H 2TC ! 4H 3TC ! 6H
(14) Window Function
This function sets the top and bottom boundary of display limit on a screen. The window function is valid only in the CC mode. The top boundary is set by window H registers 1 and 2. The bottom boundary is set by window L registers 1 and 2. This function is turned on and off by bit 5 of the OSD control register (refer to Figure 55). The structure of window H registers 1 and 2 is shown in Figure 86, the structure of window L registers 1 and 2 is shown in Figure 87.
Notes 1: Set values except "0016" and "0116" to the window H register 1 when the window H register 2 is "0016." 2: Set the register value fit for the following condition : (WH1 + WH2) < (WL1 + WL2)
ABCDE F GH I J
EXOSD mode
Top boundary of window
CC mode CC mode CC mode Window
KL
MNO
PQRST UV WX Y
Screen
OSD mode
Bottom boundary of window
Fig. 85. Example of Window Function
78
P
. e tion ang ifica t to ch pec c al s subje a fin are not its is is ntic lim : Th tice arame No e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
7
0 Window H register 1 (WH1 : address 021C 16) Control bits of window top boundary (Note) Top boundary position (low-order 8bits) TH ! (setting value of low-order 2bits of WH2 ! 16 2 + setting value of high-order 4bits of WH1 ! 161 + setting value of low-order 4bits of WH1 ! 16 0 )
7
0 Window H register 2 (WH2 : address 021E16) Control bits of window top boundary (Note) Top boundary position (high-order 2bits) TH ! (setting value of low-order 2bits of WH2 ! 16 2 + setting value of high-order 4bits of WH1 ! 16 1 + setting value of low-order 4bits of WH1 ! 16 0 )
Note : Set values except "00 16" and "0116" to the WH1 when the WH2 is "0016."
Fig. 86. Window H Registers
7
0
Window L register 1 (WL1 : address 021D16) Control bits of window bottom boundary (Note) Bottom boundary position (low-order 8bits) TH ! (setting value of low-order 2bits of WL2 ! 16 2 + setting value of high-order 4bits of WL1 ! 16 1 + setting value of low-order 4bits of WL1 ! 16 0 )
7
0
Window L register 2 (WL2 : address 021F16) Control bits of window bottom boundary (Note) Bottom boundary position (high-order 2bits) TH ! (setting value of low-order 2bits of WL2 ! 16 2 + setting value of high-order 4bits of WL1 ! 16 1 + setting value of low-order 4bits of WL1 ! 16 0 )
Note : Set values fit for the following condition : (WH1 + WH2) < (WL1 + WL2).
Fig. 87. Window L Registers
79
P
. e tion ang ifica t to ch pec c al s subje fin re a ot a is n limits This ntic ice: arame Not e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
(15) OSD Output Pin Control
The OSD output pins R, G, B, and OUT1 can also function as ports P52, P53, P54 and P55. Set the corresponding bit of the OSD port control register (address 00CB16) to "0" to specify these pins as OSD output pins, or set it to "1" to specify it as a general-purpose port P5 pins. The OUT2 can also function as port P10. Set the corresponding bit of the port P1 direction register (address 00C316) to "1" (output mode). After that, switch between the OSD output function and the port function by the OSD port control register. Set the corresponding bit to "1" to specify the pin as OSD output pin, or set it to "0" to specify as port P1 pin. The input polarity of the HSYNC, VSYNC and output polarity of signals R, G, B, OUT1 and OUT2 can be specified with the I/O polarity control register (address 021716) . Set a bit to "0" to specify positive polarity; set it to "1" to specify negative polarity (refer to Figure 68). The OSD port control register is shown in Figure 88.
7 0 0
0 0 OSD port control register (PF : address 00CB16)
Fix these bits to "0." Port P52 output signal selection bit 0 : R signal output 1 : Port P52 output Port P53 output signal selection bit 0 : G signal output 1 : Port P53 output Port P54 output signal selection bit 0 : B signal output 1 : Port P54 output Port P55 output signal selection bit 0 : OUT1 signal output 1 : Port P55 output Port P10 output signal selection bit 0 : Port P10 output 1 : OUT2 signal output Fix this bit to "0."
Fig. 88. OSD Port Control Register
80
P
. e tion ang ifica t to ch pec c al s subje a fin are not its is is ntic lim : Th tice arame No e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
(16) Raster Coloring Function
An entire screen (raster) can be colored by setting the bits 6 to 0 of the raster color register. Since each of the R, G, B, OUT1, and OUT2 pins can be switched to raster coloring output, 7 raster colors can be obtained. If the OUT1 pin has been set to raster coloring output, a raster coloring signal is always output during 1 horizontal scanning period. This setting is necessary for erasing a background TV image. If the R, G, and B pins have been set to output, a raster coloring signal is output in the part except a no-raster colored character (in Figure 90, a character "1") and the character background output during 1 horizontal scanning period. This ensures that the character color/ the character background color is not mixed with the raster color. The structure of the raster color register is shown in Figure 89, the example of raster coloring is shown in Figure 90.
7
0 Raster color register (RC : address 021816) Raster color R control bit 0 : No output 1 : Output Raster color G control bit 0 : No output 1 : Output Raster color B control bit 0 : No output 1 : Output Raster color I1 control bit 0 : No output 1 : Output
Raster color OUT2 control bit 0 : No output 1 : Output OSD interrupt source selection bit 0 : Interrupt occurs at end of OSD or EXOSD block display 1 : Interrupt occurs at end of CC mode block display
Fig. 89. Raster Color Register
: Character color "RED" (R) : Border color "GREEN" (G) : Background color "MAGENTA" (R and B) : Raster color "BLUE" (B and OUT1)
A
A'
HSYNC OUT1 R G B
Signals across A-A'
Fig. 90. Example of Raster Coloring
81
P
. e tion ang ifica t to ch pec c al s subje fin re a ot a is n limits This ntic ice: arame Not e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
ROM CORRECTION FUNCTION
This can correct program data in ROM. Up to 2 addresses (2 blocks) can be corrected, a program for correction is stored in the ROM correction memory in RAM. The ROM memory for correction is 32 bytes ! 2 blocks. Block 1 : addresses 02C016 to 02DF16 Block 2 : addresses 02E016 to 02FF16 Set the address of the ROM data to be corrected into the ROM correction address register. When the value of the counter matches the ROM data address in the ROM correction address, the main program branches to the correction program stored in the ROM memory for correction. To return from the correction program to the main program, the op code and operand of the JMP instruction (total of 3 bytes) are necessary at the end of the correction program. When the blocks 1 and 2 are used in series, the above instruction is not needed at the end of the block 1. The ROM correction function is controlled by the ROM correction enable register. Notes 1 : Specify the first address (op code address) of each instruction as the ROM correction address. 2 : Use the JMP instruction (total of 3 bytes) to return from the main program to the correction program. 3 : Do not set the same ROM correction address to blocks 1 and 2.
ROM correction address 1 (high-order) ROM correction address 1 (low-order) ROM correction address 2 (high-order) ROM correction address 2 (low-order)
024216 024316 024416 024516
Fig. 91. ROM Correction Address Registers
7 0 0
0
ROM correction enable register (RCR : address 024616) Block 1 enable bit 0 : Disabled 1 : Enabled Block 2 enable bit 0 : Disabled 1 : Enabled
Fix these bits to " 0."
Fig. 92. ROM Correction Enable Register
82
P
. e tion ang ifica t to ch pec c al s subje fin re a ot a is n limits This ntic ice: arame Not e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
RESET CIRCUIT
When the oscillation of a quartz-crystal oscillator or a ceramic resonator is stable and the power source voltage is 5 V 10 %, hold the ______ RESET pin at LOW for 2 s or more, then return is to HIGH. Then, as shown in Figure 94, reset is released and the program starts form the address formed by using the content of address FFFF16 as the high-order address and the content of the address FFFE16 as the low-order address. The internal state of microcomputer at reset are shown in Figures 5 to 9. An example of the reset circuit is shown in Figure 93. The reset input voltage must be kept 0.9 V or less until the power source voltage surpasses 4.5 V.
Poweron 4.5 V Power source voltage 0 V
Reset input voltage 0 V
0.9 V
27 1 5
M51953AL
Vcc
30
RESET
4 3 0.1 F 26
Vss
M37274MA-XXXSP
Fig. 93. Example of Reset Circuit
XIN RESET Internal RESET SYNC Address Data 32768 count of XIN clock cycle (Note 3) ? ? ? ?
01, S
01, S-1 01, S-2
FFFE
FFFF
ADH, ADL
Reset address from the vector table ? ? ? ADL ADH
Notes 1 : f(XIN) and f( ) are in the relation : f(XIN) = 2*f (). 2 : A question mark (?) indicates an undefined state that depends on the previous state. 3 : Immediately after a reset, timer 3 and timer 4 are connected by hardware. At this time, "FF 16" is set in timer 3 and "0716" is set to timer 4. Timer 3 counts down with f(XIN)/16, and reset state is released by the timer 4 overflow signal.
Fig. 94. Reset Sequence
83
P
. e tion ang ifica t to ch pec c al s subje fin re a ot a is n limits This ntic ice: arame Not e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
CLOCK GENERATING CIRCUIT
The M37274MA-XXXSP has 2 built-in oscillation circuits. An oscillation circuit can be formed by connecting a resonator between XIN and XOUT (XCIN and XCOUT). Use the circuit constants in accordance with the resonator manufacturer's recommended values. No external resistor is needed between XIN and XOUT since a feed-back resistor exists on-chip. However, an external feed-back resistor is needed between XCIN and XCOUT. When using XCIN-XCOUT as subclock, clear bits 5 and 4 of the clock source control register to "0." To supply a clock signal externally, input it to the XIN (XCIN) pin and make the XOUT (XCOUT) pin open. When not using XCIN clock, connect the XCIN to VSS and make the XCOUT pin open. After reset has completed, the internal clock is half the frequency of XIN. Immediately after poweron, both the XIN and XCIN clock start oscillating. To set the internal clock to low-speed operation mode, set bit 7 of the CPU mode register (address 00FB16) to "1."
(3) Low-Speed Mode
If the internal clock is generated from the sub-clock (XCIN), a low power consumption operation can be realized by stopping only the main clock XIN. To stop the main clock, set bit 6 (CM6) of the CPU mode register (00FB16) to "1." When the main clock XIN is restarted, the program must allow enough time to for oscillation to stabilize. Note that in low-power-consumption mode the XCIN-XCOUT drivability can be reduced, allowing even lower power consumption. To reduce the XCIN-XCOUT drivability, clear bit 5 (CM5) of the CPU mode register (00FB16) to "0." At reset, this bit is set to "1" and strong drivability is selected to help the oscillation to start. When an STP instruction is executed, set this bit to "1" by software before executing.
Oscillation Control (1) Stop mode
The built-in clock generating circuit is shown in Figure 95. When the STP instruction is executed, the internal clock stops at HIGH. At the same time, timers 3 and 4 are connected by hardware and "FF16" is set in timer 3 and "0716" is set in timer 4. Select f(XIN)/16 or f(XCIN)/ 16 as the timer 3 count source (set both bit 0 of the timer mode register 2 and bit 6 at address 00C716 to "0" before the execution of the STP instruction). Moreover, set the timer 3 and timer 4 interrupt enable bits to disabled ("0") before execution of the STP instruction. The oscillator restarts when external interrupt is accepted. However, the internal clock keeps its "H" level until timer 4 overflows, allowing time for oscillation stabilization when a ceramic resonator or a quartz-crystal oscillator is used.
M37274MA-XXXSP XCIN
Rf
XCOUT
XIN
XOUT
Rd
CCIN
CCOUT
CIN
COUT
Fig. 95. Ceramic Resonator Circuit Example
When the WIT instruction is executed, the internal clock stops in the "H" level but the oscillator continues running. This wait state is released at reset or when an interrupt is accepted (Note). Since the oscillator does not stop, the next instruction can be executed at once. Note: In the wait mode, the following interrupts are invalid. (1) VSYNC interrupt (2) OSD interrupt (3) Timers 1 and 2 interrupts using TIM2 pin input as count source (4) Timer 3 interrupt using TIM3 pin input as count source (5) Data slicer interrupt (6) Multi-master I2C-BUS interface interrupt (7) f(XIN)/4096 interrupt (8) All timer interrupts using f(XIN)/2 or f(XCIN)/2 as count source (9) All timer interrupts using f(XIN)/4096 or f(XCIN)/4096 as count source (10) A-D conversion interrupt
(2) Wait mode
M37274MA-XXXSP XCIN XCOUT XIN Open External oscillation circuit or external pulse Vcc Vss XOUT Open External oscillation circuit Vcc Vss
Fig. 96. External Clock Input Circuit Example
84
P
. e tion ang ifica t to ch pec c al s subje fin re a ot a is n limits This ntic ice: arame Not e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
XCIN
XCOUT
XIN
OSC1 oscillating mode selection bits (Notes 1, 4) XOUT "1" 1/2 "0" Internal system clock selection bit (Notes 1, 3) 1/8 "1" "0"
Timer 3 count stop bit (Notes 1, 2) Timer 3
Timer 4 count stop bit (Notes 1, 2) Timer 4
Timer 3 count source selection bit (Notes 1, 2) Timing (Internal clock)
Main clock (XIN-XOUT) stop bit (Notes 1, 3) Internal system clock selection bit (Notes 1, 3) Q S S Q Q S
Reset STP instruction
R
STP instruction
WIT instruction
R
R
Reset Interrupt disable flag I Interrupt request
Notes 1 : The value at reset is "0." 2 : Refer to the structure of timer mode register 2. 3 : Refer to the structure of CPU mode register (next page). 4 : Refer to the structure of clock source control register.
Fig. 97. Clock Generating Circuit Block Diagram
85
P
. e tion ang ifica t to ch pec c al s subje fin re a ot a is n limits This ntic ice: arame Not e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
Reset
High-speed operation start mode
WIT instruction 8MHz oscillating 32kHz oscillating is stopped (HIGH) Timer operating Interrupt External INT, timer interrupt, or SI/O interrupt 8MHz oscillating 32kHz oscillating f() = 4MHz
STP instruction 8MHz stopped 32kHz stopped is stopped (HIGH) Interrupt (Note 1) External INT CM7 = 0
CM7 = 1
WIT instruction 8MHz oscillating 32kHz oscillating is stopped (HIGH) Timer operating (Note 3) 8MHz oscillating 32kHz oscillating f() = 16kHz Interrupt
STP instruction 8MHz stopped 32kHz stopped is stopped (HIGH) Interrupt (Note 2)
CM6 = 0 The program must allow time for 8MHz oscillation to stabilize
CM6 = 1
8MHz stopped 32kHz oscillating is stopped (HIGH) Timer operating (Note 3)
WIT instruction 8MHz stopped 32kHz oscillating f() = 16kHz Interrupt
STP instruction 8MHz stopped 32kHz stopped = stopped (HIGH ) Interrupt (Note 2)
CPU mode register (Address : 00FB16) CM6 : Main clock (X IN-XOUT) stop bit 0 : Oscillating 1 : Stopped CM7 : Internal system clock selection bit 0 : XIN-XOUT selected (high-speed mode) 1 : XCIN-XCOUT selected (low-speed mode)
The example assumes that 8 MHz is being applied to the X
IN
pin and 32 kHz to the X CIN pin. The indicates the internal clock.
Notes 1: When the STP state is ended, a delay of approximately 8ms is automatically generated by timer 3 and timer 4. 2: The delay after the STP state ends is approximately 2s. 3: When the internal clock divided by 8 is used as the timer count source, the frequency of the count source is 2kHz.
Fig. 98. State Transitions of System Clock
86
P
. e tion ang ifica t to ch pec c al s subje fin re a ot a is n limits This ntic ice: arame Not e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
DISPLAY OSCILLATION CIRCUIT
The OSD oscillation circuit has a built-in clock oscillation circuits, so that a clock for OSD can be obtained simply by connecting an LC, a ceramic resonator, or a quartz-crystal oscillator across the pins OSC1 and OSC2. Which of the sub-clock or the OSD oscillation circuit is selected by setting bits 5 and 4 of the clock source control register (address 021616).
ADDRESSING MODE
The memory access is reinforced with 17 kinds of addressing modes. Refer to SERIES 740
MACHINE INSTRUCTIONS
There are 71 machine instructions. Refer to SERIES 740
PROGRAMMING NOTES
(1) The divide ratio of the timer is 1/(n+1). (2) Even though the BBC and BBS instructions are executed immediately after the interrupt request bits are modified (by the program), those instructions are only valid for the contents before the modification. At least one instruction cycle is needed (such as an NOP) between the modification of the interrupt request bits and the execution of the BBC and BBS instructions. (3) After the ADC and SBC instructions are executed (in the decimal mode), one instruction cycle (such as an NOP) is needed before the SEC, CLC, or CLD instruction is executed. (4) An NOP instruction is needed immediately after the execution of a PLP instruction. (5) In order to avoid noise and latch-up, connect a bypass capacitor ( 0.1 mF) directly between the VCC pin-VSS pin, AVCC pin-VSS pin, and the VCC pin-CNVSS pin, using a thick wire.
OSC1
OSC2
L C1 C2
Fig. 99. Display Oscillation Circuit
AUTO-CLEAR CIRCUIT
When a power source is supplied, the auto-clear function will oper______ ate by connecting the following circuit to the RESET pin.
DATA REQUIRED FOR MASK ORDERS
The following are necessary when ordering a mask ROM production:
Circuit example 1
(1) Mask ROM Order Confirmation Form (2) Mark Specification Form (3) Data to be written to ROM, in EPROM form (32-pin DIP Type 27C101, three identical copies)
Vcc
RESET
Vss
Circuit example 2
RESET
Vcc
Vss
Note : Make the level change from "L" to "H" at the point at which the power source voltage exceeds the specified voltage.
Fig. 100. Auto-clear Circuit Example
87
P
. e tion ang ifica t to ch pec c al s subje fin re a ot a is n limits This ntic ice: arame Not e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
ABSOLUTE MAXIMUM RATINGS
Symbol VCC, AVCC VI VI Input voltage Input voltage Parameter Power source voltageVCC, AVCC CNVSS P00-P07, P10-P17, P20-P27, P30, P31, P40-P46, P64, P63, P70-P72, XIN, HSYNC, VSYNC, ______ RESET P03, P10-P17, P20-P27, P30, P31, P52-P55, SOUT, SCLK, XOUT, OSC2 P00-P02, P04-P07 P52-P55, P10, P03, P15-P17, P20-P27, P30, P31 P52-P55, P10, , P03, P15-P17, P20-P27, SOUT, SCLK P11-P14 P00-P02, P04-P07 P30, P31 Ta = 25 C Conditions All voltages are based on VSS. Output transistors are cut off. Ratings -0.3 to 6 -0.3 to 6 -0.3 to VCC + 0.3 Unit V V V
VO
Output voltage
-0.3 to VCC + 0.3
V
VO IOH IOL1 IOL2 IOL3 IOL4 Pd Topr Tstg
Output voltage Circuit current Circuit current Circuit current Circuit current Circuit current
-0.3 to 13 0 to 1 (Note 1) 0 to 2 (Note 2) 0 to 6 (Note 2) 0 to 1 (Note 2) 0 to 10 (Note 3) 550 -10 to 70 -40 to 125
V mA mA mA mA mA mW C C
Power dissipation Operating temperature Storage temperature
RECOMMENDED OPERATING CONDITIONS (Ta = -10 C to 70 C, VCC = 5 V 10 %, unless otherwise noted)
Symbol VCC, AVCC VCC, AVCC VSS VIH1 Parameter Power source voltage (Note 4), During CPU, OSD, data slicer operation RAM hold voltage (when clock is stopped) Power source voltage HIGH input voltage P00-P07, P10-P17, P20-P27, P30, P31, P40-P46, P64, P70-P72, HSYNC, VSYNC, ______ RESET, XIN, P63 HIGH input voltage SCL1, SCL2, SDA1, SDA2 LOW input voltage P00-P07, P10-P17, P20-P27, P30, P31, P40-P46, P63, P64, P70-P72 LOW input voltage SCL1, SCL2, SDA1, SDA2 ______ LOW input voltage (Note 6) RESET, XIN, OSC1, HSYNC, VSYNC, INT1, INT2, INT3, TIM2, TIM3, SCLK, SIN HIGH average output current (Note 1) P52-P55, P10, P03, P15-P17, P20-P27, P30, P31 LOW average output current (Note 2) P52-P55, P10, P03, P15-P17, P20-P27, SOUT, SCLK LOW average output current (Note 2) P11-P14 LOW average output current (Note 2) P00-P02, P04-P07 LOW average output current (Note 3) P30, P31 Oscillation frequency (for CPU operation) (Note 5) Oscillation frequency (for sub-clock operation) Oscillation frequency (for OSD) Input frequency Input frequency Input frequency Input frequency Input amplitude video signal OSC1 XIN XCIN 7.9 29 11.0 26.5 8.0 32 27.0 Min. 4.5 2.0 0 0.8VCC Limits Typ. 5.0 0 Max. 5.5 5.5 0 VCC Unit V V V V
VIH2 VIL1 VIL2 VIL3 IOH IOL1 IOL2 IOL3 IOL4 f(XIN) f(XCIN) fOSC fhs1 fhs2 fhs3 fhs4 VI
0.7VCC 0 0 0
VCC 0.4 VCC 0.3 VCC 0.2 VCC 1 2 6 1 10 8.1 35 27.0 27.5 100 1 400 16.206 2.5
V V V V mA mA mA mA mA MHz kHz MHz kHz MHz kHz kHz V
LC oscillating mode Ceramic oscillating mode TIM2, TIM3, INT1, INT2, INT3 SCLK SCL1, SCL2 Horizontal sync. signal of video signal CVIN
15.262 1.5
15.734 2.0
88
P
. e tion ang ifica t to ch pec c al s subje fin re a ot a is n limits This ntic ice: arame Not e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
ELECTRIC CHARACTERISTICS (VCC = 5 V 10 %, VSS = 0 V, f(XIN) = 8 MHz, Ta = -10 C to 70 C, unless otherwise noted)
Symbol ICC Parameter Power source current System operation Test conditions VCC = 5.5 V, CRT OFF f(XIN) = 8 MHz Data slicer OFF CRT ON Data slicer ON VCC = 5.5 V, f(XIN) = 0, f(XCIN) = 32kHz, OSD OFF, Data slicer OFF, Low-power dissipation mode set (CM5 = "0", CM6 = "1") Wait mode VCC = 5.5 V, f(XIN) = 8 MHz VCC = 5.5 V, f(XIN) = 0, f(XCIN) = 32kHz, Low-power dissipation mode set (CM5 = "0", CM6 = "1") Stop mode VOH VOL HIGH output voltage P52-P55, P10, P03, P15-P17, P20-P27, P30, P31 LOW output voltage P52-P55, P10, SOUT, SCLK, P00-P07, P15-P17, P20-P27 LOW output voltage P30, P31 LOW output voltage P11-P14 VT+-VT-
______
Limits Min. Typ. 15 30 60 Max. 30
Unit
mA 50 200
A
2 25
4 100
mA
A
1 2.4 0.4 3.0 V 0.4 0.6 0.5 1.3 V 10 V
VCC = 5.5 V, f(XIN) = 0, f(XCIN) = 0 VCC = 4.5 V IOH = -0.5 mA VCC = 4.5 V IOL = 0.5 mA VCC = 4.5 V IOL = 10.0 mA IOL = 3 mA VCC = 4.5 V IOL = 6 mA VCC = 5.0 V
Hysteresis (Note 6)
RESET, HSYNC, VSYNC, INT1, INT2, INT3, TIM2, TIM3, SIN, SCLK, SCL1, SCL2, SDA1, SDA2 ______
IIZH
HIGH input leak current
RESET, P03, P10-P17, P20-P27, VCC = 5.5 V P30, P31, P40-P46, P63, P64, VI = 5.5 V P70-P72, HSYNC, VSYNC P00-P02, P04-P07
______
5 10 5 130
A
HIGH input leak current IIZL LOW input leak current
VCC = 5.5 V VI = 12 V
RESET, P00-P07, P10-P17, P20- VCC = 5.5 V P27, P30, P31, P40-P46, P63, VI = 0 V P64, P70-P72, HSYNC, VSYNC VCC = 4.5 V
A
RBS
I2C-BUS*BUS switch connection resistor (between SCL1 and SCL2, SDA1 and SDA2)
Notes 1: 2: 3: 4:
5: 6:
7: 8:
The total current that flows out of the IC must be 20 or less. The total input current to IC (IOL1 + IOL2 + IOL3) must be 20 mA or less. The total average input current for ports P30, P31 to IC must be 10 mA or less. Connect 0.1 F or more capacitor externally between the power source pins VCC-VSS and AVCC-VSS so as to reduce power source noise. Also connect 0.1 F or more capacitor externally between the pins VCC-CNVSS. Use a quartz-crystal oscillator or a ceramic resonator for the CPU oscillation circuit. When using the data slicer, use 8 MHz. P16, P41-P44 have the hysteresis when these pins are used as interrupt input pins or timer input pins. P11-P14 have the hysteresis when these pins are used as multi-master I2C-BUS interface ports. P17 and P46 have the hysteresis when these pins are used as serial I/O pins. When using the sub-clock, set fCLK < fCPU/3. Pin names in each parameter is described as below. (1) Dedicated pins: dedicated pin names. (2) Duble-/triple-function ports * When the same limits: I/O port name. * When the limits of functins except ports are different from I/O port limits: function pin name.
89
P
. e tion ang ifica t to ch pec c al s subje fin re a ot a is n limits This ntic ice: arame Not e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
A-D CONVERTER CHARACTERISTICS
Symbol -- -- -- VOT VFST TCONV VREF RLADDER VIA Resolution Non-linearity error Differential non-linearity error Zero transition error Full-scale transition error Conversion time Reference voltage Ladder resistor Analog input current Parameter
(VCC = 5 V 10 %, VSS = 0 V, f(XIN) = 8 MHz, Ta = -10 C to 70 C, unless otherwise noted) Test conditions Limits Min. 0 0 VCC = 5.12V IOL (SUM) = 0mA VCC = 5.12V 0 0 12.25 Typ. Max. 8 2 0.9 2 4 12.5 VCC 25 0 VREF Unit bits LSB LSB LSB LSB
s
V k V
MULTI-MASTER I2C-BUS BUS LINE CHARACTERISTICS
Symbol tBUF tHD:STA tLOW tR tHD:DAT tHIGH tF tSU:DAT tSU:STA tSU:STO Bus free time Hold time for START condition LOW period of SCL clock Rising time of both SCL and SDA signals Data hold time HIGH period of SCL clock Falling time of both SCL and SDA signals Data set-up time Set-up time for repeated START condition Set-up time for STOP condition 250 4.7 4.0 0 4.0 300 Standard clock mode High-speed clock mode Parameter Min. 4.7 4.0 4.7 1000 Max. Min. 1.3 0.6 1.3 20+0.1Cb 0 0.6 20+0.1Cb 100 0.6 0.6 300 300 0.9 Max. Unit
s s s
ns
s s
ns ns
s s
Note: Cb = total capacitance of 1 bus line
SDA tHD:STA tSU:STO
tBUF tLOW P SCL S
tR
tF Sr P
tHD:STA
tHD:DAT
tHIGH
tSU:DAT
tSU:STA
S : Start condition Sr : Restart condition P : Stop condition
Fig. 101. Definition Diagram of Timing on Multi-master I2C-BUS
90
PR
. nge ion. icat to cha ecif l sp subject fina re a ot a is n limits his ic e: T rament ic Not e pa Som
MIN ELI
ARY
MITSUBISHI MICROCOMPUTERS
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
PACKAGE OUTLINE
91
P
. e tion ang ifica t to ch pec c al s subje fin re a ot a is n limits This ntic ice: arame Not e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
GZZ-SH11-19B < 69A0 > Mask ROM number
740 FAMILY MASK ROM CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M37274MA-XXXSP MITSUBISHI ELECTRIC
Date : Receipt
Section head signature Supervisor signature
Note : Please fill in all items marked g . signature Issuance Company name
g
TEL ( Date : )
Submitted by
Supervisor
Customer Date issued
g 1. Confirmation
Specify the name of the product being ordered and the type of EPROMs submitted. Three EPROMs are required for each pattern. If at least two of the three sets of EPROMs submitted contain identical data, we will produce masks based on this data. We shall assume the responsibility for errors only if the mask ROM data on the products we produce differs from this data. Thus, extreme care must be taken to verify the data in the submitted EPROMs. Checksum code for entire EPROM EPROM type (indicate the type used) (hexadecimal notation)
27C101
EPROM address 0000016 Product name 0000F16 0600016 0FFFF16 1080016
OSD ROM ASCII code : `M37274MA -'
ROM (40 K)
1E41F16 1FFFF16
(1) (2)
Set "FF16" in the shaded area and in the addresses at which OSD ROM data does not present (refer to page 4/4). Write the ASCII codes that indicates the product name of "M37274MA-" to addresses 00000 16 to 0000F16.
EPROM data check item (Refer the EPROM data and check " " in the appropriate box) * Do you set "FF16" in the shaded areaand in the addresses at which OSD ROM data does not present (refer to page 4/4)? Yes Yes * Do you write the ASCII codes that indicates the product name of "M37274MA-" to addresses 00000 16 to 0000F16 ? g 2. Mark specification Mark specification must be submitted using the correct form for the type package being ordered fill out the appropriate mark specification form (52P4B for M37274MA-XXXSP) and attach to the mask ROM confirmation form.
(1/4)
92
P
. e tion ang ifica t to ch pec c al s subje fin re a ot a is n limits This ntic ice: arame Not e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
GZZ-SH11-19B < 69A0 >
740 FAMILY MASK ROM CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M37274MA-XXXSP MITSUBISHI ELECTRIC
Writing the product name and character ROM data onto EPROMs
Addresses 00000 16 to 0000F16 store the product name, and addresses 10800 16 to 1FFFF16 store the character pattern. If the name of the product contained in the EPROMs does not match the name on the mask ROM confirmation form, the ROM processing is disabled. Write the data correctly.
1. Inputting the name of the product with the ASCII code ASCII codes `M37274MA-' are listed on the right. The addresses and data are in hexadecimal notation.
Address 000016 000116 000216 000316 000416 000516 000616 000716
`M' = `3' = `7' = `2' = `7' = `4' = `M' = `A' =
4 D 16 3 3 16 3 7 16 3 2 16 3 7 16 3 4 16 4 D 16 4 1 16
Address 000816 000916 000A16 000B16 000C16 000D16 000E16 000F16
`-' = 2 D 16 F F 16 F F 16 F F 16 F F 16 F F 16 F F 16 F F 16
2. Inputting the character ROM Input the character ROM data to character ROM. For the character ROM data, see the next page and on.
(2/4)
93
P
. e tion ang ifica t to ch pec c al s subje fin re a ot a is n limits This ntic ice: arame Not e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
GZZ-SH11-19B < 69A0> Mask ROM number
SERIES MELPS 740 MASK ROM CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M37274MA-XXXSP MITSUBISHI ELECTRIC
Font data must be stored in the proper OSD ROM address according to the following table. (1)OSD ROM address of character font data
OSD ROM address bit Line number / Character code / Font bit
AD16 AD15 AD14 AD13 AD12 AD11 AD10 AD9 AD8 AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0
1
0
Line number
0
Character code
Font bit
Line number = 02 16 to 1516 Character code = 00 16 to FF16 Font bit = 0 : Left font 1 : Right font Example) The font data "60" (shaded area ) of the character code "AA
2 16"
is stored in address
10010100101010100
=1295416.
(2)OSD ROM address of extra font data
OSD ROM address bit Line number / Extra code / Font bit
AD16 AD15 AD14 AD13 AD12 AD11 AD10 AD9 AD8 AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0
1
1
Line number
0
0
0
0
Extra code
Font bit
Line number = 00 16 to 1916 Extra code = 00 16 to 0F16 Font bit = 0 : Left font 1 : Right font Example) The font data "03" (shaded area ) of the extra code "0A
2 16"
is stored in address
11101010000010101
=1D41516.
Left font Right font
DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
Left font Line number 0216 0316 0416 0516 0616 0716 0816 0916 0A16 0B16 0C16 0D16 0E16 0F16 1016 1116 1216 1316 1416 1516
Right font
DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
(1) Character code "AA 16"
Line number 0016 0116 0216 0316 0416 0516 0616 0716 0816 0916 0A16 0B16 0C16 0D16 0E16 0F16 1016 1116 1216 1316 1416 1516 1616 1716 1816 1916
(2) Extra code "0A 16"
(3/4)
94
P
. e tion ang ifica t to ch pec c al s subje fin re a ot a is n limits This ntic ice: arame Not e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
GZZ-SH11-19B < 69A0 >
740 FAMILY MASK ROM CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M37274MA-XXXSP MITSUBISHI ELECTRIC
The following OSD ROM addresses must be set "FF." There are no font data in these addresses. 10A0016 to 10BFF16 10E0016 to 10FFF16 1120016 to 113FF16 1160016 to 117FF16 11A0016 to 11BFF16 11E0016 to 11FFF16 1220016 to 123FF16 1260016 to 127FF16 12A0016 to 12BFF16 12E0016 to 12FFF16 1320016 to 133FF16 1360016 to 137FF16 13A0016 to 13BFF16 13E0016 to 13FFF16 1420016 to 143FF16 1460016 to 147FF16 14A0016 to 14BFF16 14E0016 to 14FFF16 1520016 to 153FF16 1560016 to 17FFF16 1802016 to 183FF16 1842016 to 187FF16 1882016 to 18BFF16 18C2016 to 18FFF16 1902016 to 193FF16 1942016 to 197FF16 1982016 to 19BFF16 19C2016 to 19FFF16 1A02016 to 1A3FF16 1A42016 to 1A7FF16 1A82016 to 1ABFF16 1AC2016 to 1AFFF16 1B02016 to 1B3FF16 1B42016 to 1B7FF16 1B82016 to 1BBFF16 1BC2016 to 1BFFF16 1C02016 to 1C3FF16 1C42016 to 1C7FF16 1C82016 to 1CBFF16 1CC2016 to 1CFFF16 1D02016 to 1D3FF16 1D42016 to 1D7FF16 1D82016 to 1DBFF16 1DC2016 to 1DFFF16 1E02016 to 1E3FF16
(4/4)
95
P
. e tion an g ifica t to ch pe c c al s subje fin re a ot a is n limits This ntic ice: arame Not e p Som
IM REL
IN
ARY
MITSUBISHI MICROCOMPUTERS
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
96
MITSUBISHI MICROCOMPUTERS
. e. tion ang ifica t to ch pec c al s subje fin re a ot a is n limits his ic e: T rament ic Not e pa Som
PRE
L
A IMIN
RY
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
APPENDIX Pin Configuration (TOP VIEW)
HSYNC VSYNC P40/AD4 P41/INT2 P42/TIM2 P43/TIM3 P24/AD3 P25/AD2 P26/AD1 P27/AD5 P00/PWM4 P01/PWM5 P02/PWM6 P17/SIN P44/INT1 P45/SOUT P46/SCLK AVCC HLF/AD6 P72/RVCO P71/VHOLD P70/CVIN CNVSS XIN XOUT VSS
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
52 51 50 49 48 47 46 45 44
P52/R P53/G P54/B P55/OUT1 P04/PWM0 P05/PWM1 P06/PWM2 P07/PWM3 P20 P21 P22 P23 P10/OUT2 P11/SCL1 P12/SCL2 P13/SDA1 P14/SDA2 P15 P16/INT3 P03/DA P30 P31 RESET P64/OSC2/XCOUT P63/OSC1/XCIN VCC
Outline 52P4B
M37274MA-XXXSP
43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27
97
MITSUBISHI MICROCOMPUTERS
ion. hange c icat ecif ject to l sp fina re sub a not mits a is li This entic m ice: Not e para Som
PR
IN LIM E
ARY
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
Memory Map
000016 1000016 00C016 00FF16 RAM (768 bytes) 020016 024816 02C016 02FF16 030016 043F16 Not used RAM for OSD (Note) (1296 bytes) 080016 0DF316 Not used 600016 ROM for OSD (11072 bytes) SFR2 area Not used ROM correction memory Block 1 : addresses 02C0 16 to 02DF16 Block 2 : addresses 02E0 16 to 02FF16 155FF16 Not used 1800016 Zero page SFR1 area 1080016 Not used
ROM (40 K bytes)
FF0016 FFDE16 FFFF16
Interrupt vector area
1E41F16 Special page 1FFFF16
Note : Refer to Table 15. Contents of OSD RAM.
Not used
98
MITSUBISHI MICROCOMPUTERS
. e. tion ang ifica t to ch pec c al s subje fin re a ot a is n limits his ic e: T rament ic Not e pa Som
PRE
L
A IMIN
RY
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
Memory Map of Special Function Register (SFR)
s SFR1 area (addresses C016 to DF16)
< Bit allocation > < State immediately after reset >
:
Name
Function bit
0 : "0" immediately after reset 1 : "1" immediately after reset ? : Indeterminate immediately after reset
: : No function bit
0 : Fix to this bit to "0" (do not write to "1") 1 : Fix to this bit to "1" (do not write to "0") Address C016 C116 C216 C316 C416 C516 C616 C716 C816 C916 CA16 CB16 CC16 CD16 CE16 CF16 D016 D116 D216 D316 D416 D516 D616 D716 D816 D916 DA16 DB16 DC16 DD16 DE16 DF16 Register
b7
Bit allocation
b0 b7
State immediately after reset ? 0016 ? 0016 ? 0016 ? 0016 ? 0016 ? 0016 ? 00 0016 0016 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?
b0
Port P0 (P0) Port P0 direction register (D0) Port P1 (P1) Port P1 direction register (D1) Port P2 (P2) Port P2 direction register (D2) Port P3 (P3) Port P3 direction register (D3) Port P4 (P4) Port P4 direction register (D4) Port P5 (P5) OSD port control register (PF) Port P6 (P6) Port P7 (P7) OSD control register (OC) Horizontal position register (HP) Block control register 1 (BC1) Block control register 2 (BC2) Block control register 3 (BC3) Block control register 4 (BC4) Block control register 5 (BC5) Block control register 6 (BC6) Block control register 7 (BC7) Block control register 8 (BC8) Block control register 9 (BC9) Block control register 10 (BC10) Block control register 11 (BC11) Block control register 12 (BC12)
T3SC
0 0
OUT2 OUT1
B
G
R
0
0 0 0 0
?
?
?
OC7 OC6 OC5 OC4 OC3 OC2 OC1 OC0 HP7 HP6 HP5 HP4 HP3 HP2 HP1 HP0 BC18 BC 17 BC 16 BC15 BC 14 BC13 BC12 BC11 BC28 BC 27 BC 26 BC25 BC 24 BC23 BC22 BC21 BC38 BC 37 BC 36 BC35 BC 34 BC33 BC32 BC31 BC48 BC 47 BC 46 BC45 BC 44 BC43 BC42 BC41 BC58 BC 57 BC 56 BC55 BC 54 BC53 BC52 BC51 BC68 BC 67 BC 66 BC65 BC 64 BC63 BC62 BC61 BC78 BC 77 BC 76 BC75 BC 74 BC73 BC72 BC71 BC88 BC 87 BC 86 BC85 BC 84 BC83 BC82 BC81 BC98 BC 97 BC 96 BC95 BC 94 BC93 BC92 BC91
BC108 BC107 BC106 BC105 BC104 BC103 BC102 BC101 BC118 BC117 BC116 BC115 BC114 BC113 BC112 BC111 BC128 BC127 BC126 BC125 BC124 BC123 BC122 BC121
99
MITSUBISHI MICROCOMPUTERS
ion. hange c icat ecif ject to l sp fina re sub a not mits a is li This entic m ice: Not e para Som
PR
IN LIM E
ARY
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
SFR1 area (addresses E016 to FF16)
< Bit allocation > < State immediately after reset >
:
Name
Function bit
0 : "0" immediately after reset 1 : "1" immediately after reset ? : Indeterminate immediately after reset
: : No function bit
0 : Fix to this bit to "0" (do not write to "1") 1 : Fix to this bit to "1" (do not write to "0") Address E016 E116 E216 E316 E416 E516 E616 E716 E816 E916 EA16 EB16 EC16 ED16 EE16 EF16 F016 F116 F216 F316 F416 F516 F616 F716 F816 F916 FA16 FB16 FC16 FD16 FE16 FF16 Register
b7
Bit allocation 0
Caption position register (CP) Start bit position register (SP) Window register (WN) Sync slice register (SSL) Data register 1 (CD1) Data register 2 (CD2) Clock run-in register 1 (CR1) Clock run-in register 2 (CR2)
Clock run-in detect register 1 (CRD1) Clock run-in detect register 2 (CRD2) Data slicer control register 1 (DSC1) Data slicer control register 2 (DSC2)
1
b0 b7 0 CP4 CP3 CP2 CP1 CP0
State immediately after reset 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 00 00 0016 0016 ? 01 FF16 0716 FF16 0716 0016 0016 ? 0016 10 0016 0016 11 0016 0016 0016 0016
b0
SP7 SP6 SP5 SP4 SP3 SP2 SP1 SP0 0 0 WN5 WN4 WN3 WN2 WN1 WN0
SSL7
0
0
0
0
1
0
1
0 1
1 0
0 0
1 1
CR13 CR12 CR11 CR10
1
1
CR21
1
CRD17 CRD15 CRD15 CRD15 CRD15 CRD27 CRD25 CRD25 CRD25 CRD25 CRD22 CRD21 CRD20 DSC17 DSC27
0 0
DSC15 DSC25
0 0
0 0
DSC12 DSC11 DSC10 DSC22 DSC21 DSC20
? ?
0 0
? ?
0 ?
0 0
0 0
Data register 3 (CD3) Data register 4 (CD4) A-D conversion register (AD) A-D control register (ADCON) Timer 1 (TM1) Timer 2 (TM2) Timer 3 (TM3) Timer 4 (TM4) Timer mode register 1 (TM1) Timer mode register 2 (TM2) I2C data shift register (S0) I2C address register (S0D) I2C status register (S1) I2C control register (S1D) I2C clock control register (S2) CPU mode register (CPUM) Interrupt request register 1 (IREQ1) Interrupt request register 2 (IREQ2) Interrupt control register 1 (ICON1) Interrupt control register 2 (ICON2)
0
ADVREF ADSTR
ADIN2 ADIN1 ADIN0
0
?
0
0
0
0
TM17 TM16 TM15 TM14 TM13 TM12 TM11 TM10 TM27 TM26 TM25 TM24 TM23 TM22 TM21 TM20
SAD6 SAD5 SAD4 SAD3 SAD2 SAD1 SAD0 RBW MST TRX BB PIN AL AAS AD0 LRB
0
0
0
0
0
?
BSEL1 BSEL0 10 BIT ALS ES0 BC2 BC1 BC0 SAD ACK FAST ACK BIT CCR4 CCR3 CCR2 CCR1 CCR0 MODE
CM7 CM6 CM5
1
1
CM2
0
0
0
0
1
1
0
0
ADR VSCR CRTR TM4R TM3R TM2R TM1R
0
T56R IICR INT2R 1MSR SIOR DSR INT1R CK0 ADE VSCE CRTE TM4E TM3E TM2E TM1E
T56S T56E IICE INT2E 1MSE SIOE DSE INT1E
100
MITSUBISHI MICROCOMPUTERS
. e. tion ang ifica t to ch pec c al s subje fin re a ot a is n limits his ic e: T rament ic Not e pa Som
PRE
L
A IMIN
RY
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
s SFR2 area (addresses 20016 to 21F16)
< Bit allocation > < State immediately after reset >
:
Name
Function bit
0 : "0" immediately after reset 1 : "1" immediately after reset ? : Indeterminate immediately after reset
: : No function bit
0 : Fix to this bit to "0" (do not write to "1") 1 : Fix to this bit to "1" (do not write to "0") Address 20016 20116 20216 20316 20416 20516 20616 20716 20816 20916 20A16 20B16 20C16 20D16 20E16 20F16 21016 21116 21216 21316 21416 21516 21616 21716 21816 21916 21A16 21B16 21C16 21D16 21E16 21F16 Register
b7 PWM0 register (PWM0) PWM1 register (PWM1) PWM2 register (PWM2) PWM3 register (PWM3) PWM4 register (PWM4) PWM5 register (PWM5) PWM6 register (PWM6) Clock run-in detect register 3 (CRD3) Clock run-in register (CR3) PWM mode register 1 (PN) PWM mode register 2 (PW) Timer 5 (TM5) Timer 6 (TM6)
CRD35 CRD34 CRD33 CRD32 CRD31 CR36 CR35 CR34 CR33 CR32 CR31 CR30
Bit allocation
b0 b7
State immediately after reset
b0
PN3 PN2 PN1 PN0
?
?
?
0 PW6 PW5 PW4 PW3 PW2 PW1 PW0
0016
Sync pulse counter register (SYC) Data slicer control register 3 (DSC3) Interrupt input polarity register (IP) Serial I/O mode register (SM) Serial I/O register (SIO) Clock source control register (CS) I/O polarity control register (PC) Raster color register (RC) Extra font color register (EC) Border color register (FC) Window H register 1 (WH1) Window L register 1 (WH1) Window H register 2 (WH2) Window L register 2 (WH2)
AD/INT3 SEL AD/INT3 PC7 SEL AD/INT3 RC7 SEL AD/INT3 SEL
SYC5 SYC4 SYC3 SYC2 SYC1 SYC0
DSC37 DSC36 DSC35 DSC34 DSC33 DSC32 DSC31 DSC30
AD/INT3 SEL AD/INT3 SEL
0 0 0
INT3 RE5 POL POL RE2 RE1 0 0 INT2 INT1 0 0 POL INT3 RE5 SM3 SM2 SM1 0 SM5 SM4 RE3 RE2 RE1 SM0 POL
CS6 RE5 CS4 RE3 RE2 RE1 CS0 CS3 CS2 CS1 POL CS5 PC6 RE5 PC4 RE3 RE2 RE1 PC0 PC5 PC2 PC1 POL RC6 RE5 POL RC5
INT3 POL INT3 INT3
INT3
1
0
0
RE3 RE2 RE1 RC0 RC2 RC1
RE5
0 0 0
RE3 RE2 RE1 EC0 0 EC2 EC1
0 0
0
0
0
FC2 FC1 FC0
WH17 WH16 WH15 WH14 WH13 WH12 WH11 WH10 WL17 WL16 WL15 WL14 WL13 WL12 WL11 WL10 WH21 WH20 WL21 WL20
? ? ? ? ? ? ? ? 0016 ? ?0 0016 0716 FF16 0016 0016 0016 ? 0016 0016 ? ? 0016 00 0016 0016 0016 0016 ? ? ? ?
0
0
0
0
0
0
101
MITSUBISHI MICROCOMPUTERS
ion. hange c icat ecif ject to l sp fina re sub a not mits a is li This entic m ice: Not e para Som
PR
IN LIM E
ARY
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
s SFR2 area (addresses 22016 to 24816)
< Bit allocation > < State immediately after reset >
:
Name
Function bit
0 : "0" immediately after reset 1 : "1" immediately after reset ? : Indeterminate immediately after reset
: : No function bit
0 : Fix to this bit to "0" (do not write to "1") 1 : Fix to this bit to "1" (do not write to "0") Address 22016 22116 22216 22316 22416 22516 22616 22716 22816 22916 22A16 22B16 22C16 22D16 22E16 22F16 23016 23116 23216 23316 23416 23516 23616 23716 23816 23916 23A16 23B16 23C16 23D16 23E16 23F16 24016 24116 24216 24316 24416 24516 24616 24716 24816 Register
b7
Bit allocation
b0 b7
State immediately after reset ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?
b0
Vertical position register 11 (VP11) Vertical position register 12 (VP12) Vertical position register 13 (VP13) Vertical position register 14 (VP14) Vertical position register 15 (VP15) Vertical position register 16 (VP16) Vertical position register 17 (VP17) Vertical position register 18 (VP18) Vertical position register 19 (VP19) Vertical position register 110 (VP110) Vertical position register 111 (VP111) Vertical position register 112 (VP112)
VP1 18 VP117 VP116 VP115 VP114 VP1 13 VP1 12 VP1 11 VP1 28 VP127 VP126 VP125 VP124 VP1 23 VP1 22 VP1 21 VP1 38 VP137 VP136 VP135 VP134 VP1 33 VP1 32 VP1 31 VP1 48 VP147 VP146 VP145 VP144 VP1 43 VP1 42 VP1 41 VP1 58 VP157 VP156 VP155 VP154 VP1 53 VP1 52 VP1 51 VP1 68 VP167 VP166 VP165 VP164 VP1 63 VP1 62 VP1 61 VP1 78 VP177 VP176 VP175 VP174 VP1 73 VP1 72 VP1 71 VP1 88 VP187 VP186 VP185 VP184 VP1 83 VP1 82 VP1 81 VP1 98 VP197 VP196 VP195 VP194 VP1 93 VP1 92 VP1 91
VP1108 VP1 107 VP1106 VP1105 VP1104 VP1103 VP1102 VP1101 VP1118 VP1 117 VP1116 VP1115 VP1114 VP1113 VP1112 VP1111 VP1128 VP1 127 VP1126 VP1125 VP1124 VP1123 VP1122 VP1121
Vertical position register 21 (VP21) Vertical position register 22 (VP22) Vertical position register 23 (VP23) Vertical position register 24 (VP24) Vertical position register 25 (VP25) Vertical position register 26 (VP26) Vertical position register 27 (VP27) Vertical position register 28 (VP28) Vertical position register 29 (VP29) Vertical position register 210 (VP210) Vertical position register 211 (VP211) Vertical position register 212 (VP212)
VP2 12 VP2 11 VP2 22 VP2 21 VP2 32 VP2 31 VP2 42 VP2 41 VP2 52 VP2 51 VP2 62 VP2 61 VP2 72 VP2 71 VP2 82 VP2 81 VP2 92 VP2 91
VP2102 VP2101 VP2112 VP2111 VP2122 VP2121
DA-H register (DA-H) DA-L register (DA-L) ROM correction address 1 (high-order) ROM correction address 1 (low-order) ROM correction address 2 (high-order) ROM correction address 2 (low-order) ROM correction enable register (RCR)
0
0
?
0 0016
0 0
RCR1 RCR0
0
0
?? 0016 0016 0016 0016 0016 0016 0016
?
?
?
102
MITSUBISHI MICROCOMPUTERS
. e. tion ang ifica t to ch pec c al s subje fin re a ot a is n limits his ic e: T rament ic Not e pa Som
PRE
L
A IMIN
RY
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
Internal State of Processor Status Register and Program Counter at Reset
< Bit allocation >
< State immediately after reset >
:
Name
Function bit
0 : "0" immediately after reset 1 : "1" immediately after reset ? : Indeterminate immediately after reset
: : No function bit
0 : Fix to this bit to "0" (do not write to "1") 1 : Fix to this bit to "1" (do not write to "0") Register
b7 Processor status register (PS) Program counter (PCH) Program counter (PCL)
Bit allocation
b0 b7
State immediately after reset
b0
N
V
T
B
D
I
Z
C
?
????1?? Contents of address FFFF16 Contents of address FFFE16
103
MITSUBISHI MICROCOMPUTERS
ion. hange c icat ecif ject to l sp fina re sub a not mits a is li This entic m ice: Not e para m So
PR
IN LIM E
ARY
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
Structure of Register
The figure of each register structure describes its functions, contents at reset, and attributes as follows: Note : The following registers are the mask version's registers.
CPU Mode Register
b7 b6 b5 b4 b3 b2 b1 b0 11 00
Bit attributes (Note 2) Bits Values immediately after reset release (Note 1)
CPU mode register (CPUM) (CM) [Address FB 16] B Name 0, 1 Processor mode bits (CM0, CM1) Functions
b1 b0
After reset R W 0 RW
0 0 1 1
0: Single-chip mode 1: 0: Not available 1: 0 1 1 0 RW RW RW RW
2
Stack page selection bit (Note) (CM2)
0: 0 page 1: 1 page
3, 4 Fix these bits to "1." Nothing is assigned. This bit is write disable bit. When this bit is read out, the value is "0." b7 b6 6, 7 Clock switch bits (CM6, CM7) 0 0: f(XIN) = 8 MHz 0 1: f(XIN) = 12 MHz 1 0: f(XIN) = 16 MHz 1 1: Do not set : Bit in which nothing is assigned Notes 1: Values immediately after reset release 0******"0" after reset release 1******"1" after reset release ?******Indeterminate after reset release 5
2: Bit attributes******The attributes of control register bits are classified into 3 types : read-only, write-only and read and write. In the figure, these attributes are represented as follows : W******Write R******Read ******Write enabled ******Read enabled ! ******Write disabled ! ******Read disabled V ******"0" can be set by software, but "1" cannot be set.
104
MITSUBISHI MICROCOMPUTERS
. e. tion ang ifica t to ch pec c al s subje a fin are not its is is ntic lim : Th tice arame No e p Som
PRE
L
A IMIN
RY
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
Port Pi Direction Register
b7 b6 b5 b4 b3 b2 b1 b0 Port Pi direction register (Di) (i=0,1,2) [Addresses 00C1 16, 00C316, 00C516]
B 0 1 2 3 4 5 6 7
Name Port Pi direction register
Functions 0 : Port Pi0 input mode 1 : Port Pi0 output mode 0 : Port Pi1 input mode 1 : Port Pi1 output mode 0 : Port Pi2 input mode 1 : Port Pi2 output mode 0 : Port Pi3 input mode 1 : Port Pi3 output mode 0 : Port Pi4 input mode 1 : Port Pi4 output mode 0 : Port Pi5 input mode 1 : Port Pi5 output mode 0 : Port Pi6 input mode 1 : Port Pi6 output mode 0 : Port Pi7 input mode 1 : Port Pi7 output mode
After reset R W 0 0 0 0 0 0 0 0 RW RW RW RW RW RW RW RW
Port Pi Direction Register
Addresses 00C116, 00C316, 00C516
Port P3 Direction Register
b7 b6 b5 b4 b3 b2 b1 b0 Port P3 direction register (D3) [Address 00C7 16]
B 0 1 2 to 5 6 7
Name Port P3 direction register
Functions 0 : Port P30 input mode 1 : Port P30 output mode 0 : Port P31 input mode 1 : Port P31 output mode
After reset R W 0 0 0 RW RW R--
Nothing is assigned. These bits are write disable bits. When these bits are read out, the values are "0." Timer 3 count source selection bit (T3SC) Ports P63, P64 selection bit Refer to Timer mode register 2 (address 00F516). Refer to clock source control register (address 021616).
0 0
RW RW
Port P3 Direction Register
Address 00C716
105
MITSUBISHI MICROCOMPUTERS
ion. hange c icat ecif ject to l sp fina re sub a not mits a is li This entic m ice: Not e para Som
PR
IN LIM E
ARY
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
Port P4 Direction Register
b7 b6 b5 b4 b3 b2 b1 b0
0
Port P4 direction register (D4) [Address 00C9 16]
B 0
Name Fix this bit to "0."
Functions
After reset R W 0 RW
1 to 4, Nothing is assigned. These bits are write disable bits. 7 When these bits are read out, the values are "0." 5 6 Port P45 selection bit Port P46 selection bit 0: SOUT pin 1: Input port P45 0: SCLK pin 1: Input port P46
0 0 0
R-- RW RW
Port P4 Direction Register
Address 00C916
OSD Port Control Register
b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 OSD port control register (PF) [Address 00CB 16]
B
Name
Functions
After reset R W 0 RW RW RW RW RW RW
0, 1, Fix these bits to "0." 7 2 3 4 5 6 Port P52 output signal selection bit (R) Port P53 output signal selection bit (G) Port P54 output signal selection bit (B) Port P55 output signal selection bit (OUT1) Port P10 output signal selection bit (OUT2) 0 : R signal output 1 : Port P52 output 0 : G signal output 1 : Port P53 output 0 : B signal output 1 : Port P54 output 0 : OUT1 signal output 1 : Port P55 output 0 : Port P10 output 1 : OUT2 signal output
0 0 0 0 0
OSD Port Control Register
Address 00CB16
106
MITSUBISHI MICROCOMPUTERS
n. ange. atio h cific ct to c spe je inal re sub f ot a its a is n lim This entic m ice: Not e para Som
PRE
L
A IMIN
RY
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
OSD Control Register
b7 b6 b5 b4 b3 b2 b1 b0 OSD control register (OC) [Address 00CE 16] B 0 1 2 3 Name OSD control bit (OC0) (See note 1) Scan mode selection bit (OC1) Border type selection bit (OC2) Functions 0 : All-blocks display off 1 : All-blocks display on 0 : Normal scnan mode 1 : Bi-scan mode 0 : All bordered 1 : Shadow bordered (See note 2) After reset R W 0 0 0 0 RW RW RW RW
Flash mode selection 0 : Color signal of character background bit (OC3) part does not flash 1 : Color signal of character background part flashes 0 : OFF 1 : ON 0 : OFF 1 : ON
b7 b6
4 Automatic solid space control bit (OC4) 5 Window control bit (OC5) 6, 7 Layer mixing control bits (OC6, OC7) (See note 3)
0 0
RW RW
0 0: Logic sum (OR) of layer 1's color and layer 2's color 0 1: Layer 1's color has priority 1 0: Layer 2's color has priority 1 1: Do not set.
0
RW
Notes 1 : Even this bit is switched during display, the display screen remains unchanged until a rising (falling) of the next V SYNC. 2 : Shadow border is output at right and bottom side of the font. 3 : Set "00" during displaying extra fonts.
OSD Control Register
Address 00CE16
Horizontal Position Register
b7 b6 b5 b4 b3 b2 b1 b0 Horizontal position register (HP) [Address 00CF 16] B Name Functions Horizontal display start positions
4TOSC ! (setting value of high-order 4 bits ! 161 + setting value of low-order 4 bits ! 160 )
After reset R W 0 RW
0 Control bits of horizontal to display start positions 7 (HP0 to HP7)
Note: The setting value synchronizes with the V SYNC.
Horizontal Position Register
Address 00CF16
107
MITSUBISHI MICROCOMPUTERS
. ion. hange c icat ecif ject to l sp fina re sub ot a its a is n his entic lim e: T otic param N e Som
PRE
L
A IMIN
RY
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
Block Control register i
b7 b6 b5 b4 b3 b2 b1 b0 Block control register i (BCi) (i=1 to 12) [Addresses 00D0 B Name
b1 b0 16
to 00BF16](See note 1) After reset RW
Functions 0 0 1 1 0: Display OFF 1: OSD mode 0: CC mode 1: EXOSD mode
0, 1 Display mode selection bits (BCi0, BCi1) (See note) 2 Border control bit (BCi2)
Indeterminate R W
0: Border OFF 1: Border ON
b6 b5 b4 0 0 1 1 0 0 1 1 0 0 1 1 -- -- 0 0 1 1 b3 CS6 Pre-divide ratio 0 0 1-- 1 1 0 1 2 0-- 1 0 1 3 0-- 1 1 0 10 0 1 0 1 1 2 Dot size Display Iayer
Indeterminate R W Indeterminate R W
3, 4 Dot size selection bits (BCi3, BCi4)
0
0
0
1
5, 6 Pre-divide ratio * layer selection bit (BCi5, BCi6)
1
0
1
1
1
1
1Tc 1/2H 1Tc 1H 2Tc 2H 3Tc 3H 1Tc 1/2H 1Tc 1H 2Tc 2H Layer1 3Tc 3H 1Tc 1/2H 1Tc 1H 2Tc 2H 3Tc 3H 1Tc 1/2H 1Tc 1H 1Tc 1/2H Layer2 1Tc 1H 1.5Tc 1/2H 1.5Tc 1H
Indeterminate R W
7
OUT2 output control bit (BCi7) (See not 2)
BC17: Window top boundary BC27: Window bottom boundary
Indeterminate R W
Notes 1: Note that EPROM version the block control registers at addresses 00D0 when programming. 2: Bit 4 of the color code 1 controls OUT1 output when bit 7 is "0." Bit 4 of the color code 1 controls OUT2 output when bit 7 is "1."
16
to 00DF16
Block Control Register i
Addresses 00D016 to 00DB16
108
MITSUBISHI MICROCOMPUTERS
. e. tion ang ifica t to ch pec c al s subje fin re a ot a is n limits his ic e: T rament ic Not e pa Som
PRE
L
A IMIN
RY
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
Caption Position Register
b7 b6 b5 b4 b3 b2 b1 b0 1 0 0 Caption Position Register (CPS) [Address 00E0 16]
B
Name
Functions
After reset 0
RW RW
0 Specification main data to slice line (CP0 to CP4) 4 5, 6 Fix these bits to "0."
0
RW
7
Fix this bit to "0."
0
RW
Caption Position Register
Address 00E016
Start Bit Position Register
b7 b6 b5 b4 b3 b2 b1 b0 Start bit position register (SP) [Address 00E1 16]
B 0 to 6
Name
Functions
After reset 0
RW RW
Start bit generating time Time from a falling of the horizontal (SP0 to SP6) synchronous signal to occurrence of a start bit = 4 ! set value ("0016" to "7F16") ! reference clock period DSC1 bit 7 control bit (SP7) 0 : Generation of 16 pulses 1 : Generation of 16 pulses and detection of clock run-in pulse (4 to 6 pulses)
7
0
RW
Start Bit Position Register
Address 00E116
Window Register
b7 b6 b5 b4 b3 b2 b1 b0 0 0 Window register (WN) [Address 00E2 16]
B 0 to 5
Name Window start time (WN0 to WN5)
Functions Time from a falling of the horizontal synchronous signal to start of the window = 4 ! set value ("0016" to "3F16") ! reference clock period
After reset 0
RW RW
6, 7 Fix these bits to "0."
0
RW
Window Register
Address 00E216
109
MITSUBISHI MICROCOMPUTERS
ion. hange c icat ecif ject to l sp fina re sub a not mits a is li This entic m ice: Not e para Som
PR
IN LIM E
ARY
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
Sync Slice Register
b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 1 0 1 Sync slice register (SSL) [Address 00E3 16]
B 0, 2
Name Fix these bits to "1."
Functions
After reset 0
RW RW
1, Fix these bits to "0." 3 to 6 7 Vertical synchronous signal (Vsep) generating method selection bit (SSL7) 0: Method 1 1: Method 2
0
RW
0
RW
Sync Slice Register
Address 00E316
Clock Run-in Register 1
b7 b6 b5 b4 b3 b2 b1 b0 0 1 0 1 Clock run-in register 1 (CR1) [Address 00E6 16]
B 0 to 3 4, 6
Name Clock run-in count value of main-data slice line (CR10 to CR13) Fix these bits to "1."
Functions
After reset 0
RW RW
0
RW
5, 7
Fix these bits to "0."
0
RW
Clock Run-in Register 1
Address 00E616
Clock Run-in Register 2
b7 b6 b5 b4 b3 b2 b1 b0 1 0 0 1 1 1 1 Clock run-in register 2 (CR2) [Address 00E7 16]
B
Name
Functions
After reset 0
RW RW
0, Fix these bits to "1." 2 to 4, 7 1 Start bit detecting method selection bit (CR21) Fix these bits to "0." 0: Method 1 1: Method 2
0
RW
5, 6
0
RW
Clock Run-in Register 2
Address 00E716
110
MITSUBISHI MICROCOMPUTERS
. e. tion ang ifica t to ch pec c al s subje fin re a ot a is n limits his ic e: T rament ic Not e pa Som
PRE
L
A IMIN
RY
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
Clock Run-in Detect Register i
b7 b6 b5 b4 b3 b2 b1 b0 Clock run-in detect register i (CRDi) (i=1, 3) [Addresses 00E8 16, 020816]
B 0 to 2 3 to 7
Name Test bits Read-only
Functions
After reset 0
RW RW
Clock run-in detection bits (CRDi3 to CRDi7)
Number of reference clock s to be counted one clock runin pulse period
0
R--
Clock Run-in detect Register i
Addresses 00E816, 020816
Clock Run-in Detect Register 2
b7 b6 b5 b4 b3 b2 b1 b0 Clock run-in detect register 2 (CRD2) [Address 00E9 16]
B 0 to 2
Name Clock run-in pulses for sampling (CRD20 to CRD22) b2 0 0 0 0 1 1 1 1 b1 0 0 1 1 0 0 1 1
Functions b0 0 : Not available 1 : 1st pulse 0 : 2nd pulse 1 : 3rd pulse 0 : 4th pulse 1 : 5th pulse 0 : 6th pulse 1 : 7th pulse
After reset 0
RW RW
3 to 7
Data clock generating time (CRD23 to CRD27)
Time from detection of a start bit to occurrence of a data clock = (13 + set value) ! reference clock period
0
RW
Clock Run-in detect Register 2
Address 00E916
111
MITSUBISHI MICROCOMPUTERS
ion. hange c icat ecif ject to l sp fina re sub a not mits a is li This entic m ice: Not e para Som
PR
IN LIM E
ARY
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
Data Slicer Control Register 1
b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 Data slicer control register 1(DSC1) [Address 00EA 16]
B 0
Bit Data slicer control bit (DSC10)
Functions 0: Data slicer stopped 1: Data slicer operating b2 0 0 1 1 Field of main b1 data slice line 0 F2 1 F1 0 F1 and F2 1 F1 and F2 Field for setting refernce voltage F2 F1 F2 F1
After reset 0 0
RW RW RW
1, 2 Field to be sliced data selection bit (DSC11, DSC12)
3, 4, Fix these bits to "0." 6 5 Field determination flag (DSC15) 0 : Hsep Vsep
0
RW
Indeterminate R --
1 : Hsep Vsep 7 Data latch completion flag for caption data in main data slice line (DSC17) 0: Data is not yet latched 1: Data is latched
Indeterminate R W
Definition of fields 1 (F1) and 2 (F2) F1 : Hsep VSYNC Vsep
F2 : Hsep VSYNC Vsep
Data Slicer Control Register 1
Address 00EA16
112
MITSUBISHI MICROCOMPUTERS
. e. tion ang ifica t to ch pec c al s subje fin re a ot a is n limits his ic e: T rament ic Not e pa Som
PRE
L
A IMIN
RY
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
Data slicer Control Register 2
b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 Data slicer Control register 2 (DSC2) [Address 00EB 16]
B 0
Name Timing signal generating circuit control bit (DSC20) Reference clock source selection bit (DSC21)
Functions 0: Stopped 1: Operating 0: Video signal 1: HSYNC signal Read-only
After reset 0
RW RW
1
0
RW
2, 7 Test bit 3, 4, Fix these bits to "0." 6 5
Indeterminate R -- 0 RW
V-pulse shape determination 0: Match flag (DSC25) 1: Mis match
Indeterminate R --
Data Slicer Control Register 2
Address 00EB16
A-D Control Register
b7 b6 b5 b4 b3 b2 b1 b0
0
0
A-D control register (ADCON) [Address 00EF 16]
B
0 to 2
Name
Analog input pin selection bits (ADIN0 to ADIN2) b2 0 0 0 0 1 1 1 1 b1 0 0 1 1 0 0 1 1
Functions
b0 0 : AD1 1 : AD2 0 : AD3 1 : AD4 0 : AD5 1 : AD6 0: Do not set. 1:
After reset R W
0
RW
3 4 6
A-D conversion completion bit (ADSTR) VCC connection selection bit (ADVREF)
0: Conversion in progress 1: Convertion completed 0: OFF 1: ON
Indeterminate Indeterminate Indeterminate
RW RW R-- R--
Nothing is assigned. This bit is a write disable bit. When this bit is read out, the value is indeterminate.
5, 7 Fix these bits to "0."
0
A-D Control Register
Address 00EF16
113
MITSUBISHI MICROCOMPUTERS
ion. hange c icat ecif ject to l sp fina re sub a not mits a is li This entic m ice: Not e para Som
PR
IN LIM E
ARY
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
Timer Mode Register 1
b7 b6 b5 b4 b3 b2 b1 b0 Timer mode register 1 (TM1) [Address 00F4 16] B Name 0 Timer 1 count source selection bit 1 (TM10) 1 Timer 2 count source selection bit 1 (TM11) Timer 1 count stop bit (TM12) Timer 2 count stop bit (TM13) Timer 2 count source selection bit 2 (TM14) Timer 1 count source selection bit 2 (TM15) Timer 5 count source selection bit 2 (TM16) Timer 6 internal count source selection bit (TM17) Functions After reset R W 0: f(XIN)/16 or f(XCIN)/16 (Note) 0 RW 1: Count source selected by bit 5 of TM1 0: Count source selected by bit 4 of TM1 1: External clock from TIM2 pin 0: Count start 1: Count stop 0: Count start 1: Count stop 0: f(XIN)/16 or f(XCIN)/16 (See note) 1: Timer 1 overflow 0: f(XIN)/4096 or f(XCIN)/4096 (See note) 1: External clock from TIM2 pin 0: Timer 2 overflow 1: Timer 4 overflow 0: f(XIN)/16 or f(XCIN)/16 (See note) 1: Timer 5 overflow 0 RW
2 3 4
0 0 0
RW RW RW
5
0
RW
6 7
0 0
RW RW
Timer Mode Register 1
Address 00F416
114
MITSUBISHI MICROCOMPUTERS
. e. tion ang ifica t to ch pec c al s subje fin re a ot a is n limits his ic e: T rament ic Not e pa Som
PRE
L
A IMIN
RY
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
Timer Mode Register 2
b7 b6 b5 b4 b3 b2 b1 b0 Timer mode register 2 (TM2) [Address 00F5 16] B Name 0 Timer 3 count source selection bit (TM20) Functions (b6 at address 00C716) b0 0 0 : f(XIN)/16 or f(XCIN)/16 (See note) 0 1 : f(XCIN) 1 0: External clock from TIM3 pin 1 1: b4 0 0 1 1 b1 0 : Timer 3 overflow signal 1 : f(XIN)/16 or f(XCIN)/16 (See note) 0 : f(XIN)/2 or f(XCIN)/2 (See note) 1 : f(XCIN) After reset R W 0 RW
1, 4 Timer 4 count source selection bits (TM21, TM24)
0
RW
2 3 5 6 7
Timer 3 count stop bit (TM22) Timer 4 count stop bit (TM23) Timer 5 count stop bit (TM25) Timer 6 count stop bit (TM26) Timer 5 count source selection bit 1 (TM27)
0: Count start 1: Count stop 0: Count start 1: Count stop 0: Count start 1: Count stop 0: Count start 1: Count stop 0: f(XIN)/16 or f(XCIN)/16 (See note) 1: Count source selected by bit 6 of TM1
0 0 0 0 0
RW RW RW RW RW
Note: Either f(XIN) or f(XCIN) is selected by bit 7 of the CPU mode register.
Timer Mode Register 2
Address 00F516
I2C Data Shift Register
b7 b6 b5 b4 b3 b2 b1 b0 I C data shift register1(S0) [Address 00F616]
2
B 0 to 7
Name D0 to D7
Functions This is an 8-bit shift register to store receive data and write transmit data.
After reset
RW
Indeterminate R W
Note: To write data into the I2C data shift register after setting the MST bit to "0" (slave mode), keep an interval of 8 machine cycles or more.
I2C Data Shift Register
Address 00F616
115
MITSUBISHI MICROCOMPUTERS
ion. hange c icat ecif ject to l sp fina re sub a not mits a is li This entic m ice: Not e para Som
PR
IN LIM E
ARY
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
I2C Address Register
b7 b6 b5 b4 b3 b2 b1 b0
I2C address register (S0D) [Address 00F7 16] B
0 1 to 7
Name
Read/write bit (RBW) Slave address (SAD0 to SAD6) 0: Read 1: Write
Functions
After reset R W
0 0
R-- RW
The address data transmitted from the master is compared with the contents of these bits.
I2C Address Register
Address 00F716
I2C Status Register
b7 b6 b5 b4 b3 b2 b1 b0
I2C status register (S1) [Address 00F8 16] B
0 1 2 3 4 5
Name
Last receive bit (LRB) (See note) General call detecting flag (AD0) (See note) Slave address comparison flag (AAS) (See note) Arbitration lost detecting flag (AL) (See note) I2C-BUS interface interrupt request bit (PIN) Bus busy flag (BB)
Functions
0 : Last bit = "0 " 1 : Last bit = "1 " 0 : No general call detected 1 : General call detected 0 : Address mismatch 1 : Address match 0 : Not detected 1 : Detected 0 : Interrupt request issued 1 : No interrupt request issued 0 : Bus free 1 : Bus busy b7 0 0 1 1 b6 0 : Slave recieve mode 1 : Slave transmit mode 0 : Master recieve mode 1 : Master transmit mode
After reset R W
Indeterminate 0 0 0 0 0 0
R-- R-- R-- R-- R-- RW RW
6, 7 Communication mode specification bits (TRX, MST)
Note : These bits and flags can be read out, but cannnot be written.
I2C Status Register
Address 00F816
116
MITSUBISHI MICROCOMPUTERS
. e tion ang ifica t to ch pec c al s subje fin re a ot a is n limits This ntic ice: arame Not e p Som
PRE
L
A IMIN
RY
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
I2C Control Register
b7 b6 b5 b4 b3 b2 b1 b0 I2C control register (S1D : address 00F9 16)
B
0 to 2
Name
Bit counter (Number of transmit/recieve bits) (BC0 to BC2) b2 0 0 0 0 1 1 1 1 b1 0 0 1 1 0 0 1 1 b0 0: 1: 0: 1: 0: 1: 0: 1:
Functions
8 7 6 5 4 3 2 1
After reset R W
0
RW
3 4 5
I2 C-BUS interface use enable bit (ESO) Data format selection bit (ALS) Addressing format selection bit (10BIT SAD)
0 : Disabled 1 : Enabled 0 : Addressing mode 1 : Free data format 0 : 7-bit addressing format 1 : 10-bit addressing format b7 b6 Connection port (See note) 0 0 : None 0 1 : SCL1, SDA1 1 0 : SCL2, SDA2 1 1 : SCL1, SDA1 SCL2, SDA2
0 0 0 0
RW RW RW RW
6, 7 Connection control bits between I2C-BUS interface and ports
Note: When using ports P11-P14 as I2C-BUS interface, the output structure changes automatically from CMOS output to N-channel open-drain output.
I2C Control Register
Address 00F916
I2C Clock Control Register
b7 b6 b5 b4 b3 b2 b1 b0 I2 C clock control register (S2 : address 00FA 16)
B
0 to 4
Name
Functions
High speed clock mode
After reset R W
0
SCL frequency control bits Setup value of Standard clock (CCR0 to CCR4) CCR4-CCR0 mode 00 to 02 03 04 05 06 1D 1E 1F
RW
Setup disabled Setup disabled Setup disabled Setup disabled 100 83.3
500/CCR value
333 250 400 (See note) 166
1000/CCR value
...
17.2 16.6 16.1
34.5 33.3 32.3 0
(at = 4 MHz, unit : kHz) 5 SCL mode specification bit (FAST MODE) ACK bit (ACK BIT) ACK clock bit (ACK) 0 : Standard clock mode 1 : High-speed clock mode 0 : ACK is returned. 1 : ACK is not returned. 0 : No ACK clock 1 : ACK clock
RW RW RW
6 7
0 0
Note: At 4000kHz in the high-speed clock mode, the duty is as below . "0" period : "1" period = 3 : 2 In the other cases, the duty is as below. "0" period : "1" period = 1 : 1
I2C Clock Control Register
Address 00FA16
117
MITSUBISHI MICROCOMPUTERS
ion. hange c icat ecif ject to l sp fina re sub a not mits a is li This entic m ice: Not e para Som
PR
IN LIM E
ARY
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
CPU Mode Register
b7 b6 b5 b4 b3 b2 b1 b0 11 00 CPU mode register (CPUM) (CM) [Address FB 16] B Name 0, 1 Processor mode bits (CM0, CM1) Functions
b1 b0
After reset R W 0 RW
0 0 1 1
0: Single-chip mode 1: 0: Not available 1: 1 1 RW RW RW RW
2
Stack page selection bit (CM2) (See note)
0: 0 page 1: 1 page
3, 4 Fix these bits to "1." 5 XCOUT drivability selection bit (CM5) 6 Main Clock (X IN-XOUT) stop bit (CM6) 7 Internal system clock selection bit (CM7) 0: LOW drive 1: HIGH drive 0: Oscillating 1: Stopped 0: XIN-XOUT selected (high-speed mode) 1: XCIN-XCOUT selected (high-speed mode)
1 0
0
RW
Note: This bit is set to "1" after the reset release.
CPU Mode Register
Address 00FB16
Interrupt Request Register 1
b7 b6 b5 b4 b3 b2 b1 b0 Interrupt request register 1 (IREQ1) [Address 00FC 16] B 0 1 2 3 4 5 6 7 Name Functions After reset R W 0 0 0 0 0 0 0 0 RV RV RV RV RV RV RV R--
0 : No interrupt request issued Timer 1 interrupt 1 : Interrupt request issued request bit (TM1R) Timer 2 interrupt 0 : No interrupt request issued request bit (TM2R) 1 : Interrupt request issued 0 : No interrupt request issued Timer 3 interrupt 1 : Interrupt request issued request bit (TM3R) 0 : No interrupt request issued Timer 4 interrupt 1 : Interrupt request issued request bit (TM4R) OSD interrupt request 0 : No interrupt request issued 1 : Interrupt request issued bit (CRTR) 0 : No interrupt request issued VSYNC interrupt 1 : Interrupt request issued request bit (VSCR) A-D conversion * INT3 0 : No interrupt request issued interrupt request bit (ADR) 1 : Interrupt request issued Nothing is assigned. This bit is a write disable bit. When this bit is read out, the value is "0."
V: "0" can be set by software, but "1" cannot be set.
Interrupt Request Register 1
Address 00FC16
118
MITSUBISHI MICROCOMPUTERS
. e. tion ang ifica t to ch pec c al s subje fin re a ot a is n limits his ic e: T rament ic Not e pa Som
PRE
L
A IMIN
RY
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
Interrupt Request Register 2
b7 b6 b5 b4 b3 b2 b1 b0 0 Interrupt request register 2 (IREQ2) [Address 00FD 16] B 0 Name Functions 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued 0 : No interrupt request issued 1 : Interrupt request issued After reset R W 0 0 0 0 0 0 0 0 RV RV RV RV RV RV RV RW
INT1 interrupt request bit (INT1R) 1 Data slicer interrupt request bit (DSR) 2 Serial I/O interrupt request bit (SIOR) 3 f(XIN)/4096 interrupt request bit (1MSR) 4 INT2 interrupt request bit (INT2R) 5 Multi-master I 2C-BUS interrupt request bit (IICR) 6 7 Timer 5 * 6 interrupt request bit (T56R) Fix this bit to "0."
V: "0" can be set by software, but "1" cannot be set.
Interrupt Request Register 2
Address 00FD16
Interrupt Control Register 1
b7 b6 b5 b4 b3 b2 b1 b0 Interrupt control register 1 (ICON1) [Address 00FE B 0 1 2 3 4 5 6 7 Name Timer 1 interrupt enable bit (TM1E) Timer 2 interrupt enable bit (TM2E) Timer 3 interrupt enable bit (TM3E) Timer 4 interrupt enable bit (TM4E) OSD interrupt enable bit (CRTE) VSYNC interrupt enable bit (VSCR) A-D conversion * INT3 interrupt enable bit (ADE) Functions 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled
16]
After reset R W 0 0 0 0 0 0 0 0 RW RW RW RW RW RW RW R--
Nothing is assigned. This bit is a write disable bit. When this bit is read out, the value is "0."
Interrupt Control Register 1
Address 00FE16
119
MITSUBISHI MICROCOMPUTERS
ion. hange c icat ecif ject to l sp fina re sub a not mits a is li This entic m ice: Not e para Som
PR
IN LIM E
ARY
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
Interrupt Control Register 2
b7 b6 b5 b4 b3 b2 b1 b0 Interrupt control register 2 (ICON2) [Address 00FF 16] B 0 1 2 3 4 5 6 7 Name INT1 interrupt enable bit (INT1E) Data slicer interrupt enable bit (DSR) Serial I/O interrupt enable bit (SIOE) f(XIN)/4096 interrupt enable bit (1MSE) INT2 interrupt enable bit (INT2E) Functions 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled 0 : Interrupt disabled 1 : Interrupt enabled After reset R W 0 0 0 0 0 0 0 0 RW RW RW RW RW RW RW RW
Multi-master I 2C-BUS interface 0 : Interrupt disabled interrupt enable bit (IICE) 1 : Interrupt enabled Timer 5 * 6 interrupt enable bit (T56E) Timer 5 * 6 interrupt switch bit (TM56S) 0 : Interrupt disabled 1 : Interrupt enabled 0 : Timer 5 1 : Timer 6
Interrupt Control Register 2
Address 00FF16
Clock Run-in Register 3
b7 b6 b5 b4 b3 b2 b1 b0 Clock run-in register 3 (CR3) [Address 0209 16]
B 0 to 3 4
Name Clock run-in count value of sub-data slice line (CR30 to CR33) Data latch completion flag for caption data in subdata slice line (CR34)
Functions
After reset 0
RW RW
0: Data is not latched yet 1: Data is latched
Indeterminate R W
5
Data slice line selection bit for interrupt request (CR35) Interrupt mode selection bit (CR36)
0: Main data slice line 1: Sub- data slice line 0: Interrupt occurs at end of data slice line 1: Interrupt occurs at completion of caption data latch
Indeterminate R W
6
Indeterminate R W
7
Nothing is assigned. This bit is a write disable bit. When this bit is read out, the value is "0."
Indeterminate R --
Clock Run-in Register 3
Address 020916
120
MITSUBISHI MICROCOMPUTERS
. e. tion ang ifica t to ch pec c al s subje fin re a ot a is n limits his ic e: T rament ic Not e pa Som
PRE
L
A IMIN
RY
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
PWM Mode Register 1
b7 b6 b5 b4 b3 b2 b1 b0 PWM mode register 1 (PN) [Address 020A 16] B 0 1 2 3 4 to 7 Name PWM counts source selection bit (PN0) DA/P03 output selection bit (PN1) DA output polarity selection bit (PN2) PWM output polarity selection bit (PN3) Functions 0 : Count source supply 1 : Count source stop 0 : P03 output 1 : DA output 0 : Positive polarity 1 : Negative polarity 0 : Positive polarity 1 : Negative polarity After reset 0 0 0 0 RW RW RW RW RW
Nothing is assigned. These bits are write disable bits. Indeterminate R -- When these bits are read out, the values are "0."
PWM Mode Register 1
Address 020A16
PWM Mode Register 2
b7 b6 b5 b4 b3 b2 b1 b0 0 PWM mode register 2 (PW) [Address 020B 16] B Name 0 P04/PWM0 output selection bit (PW0) 1 2 3 4 5 6 7 P05/PWM1 output selection bit (PW1) P06/PWM2 output selection bit (PW2) P07/PWM3 output selection bit (PW3) P00/PWM4 output selection bit (PW4) P01/PWM5 output selection bit (PW5) P02/PWM6 output selection bit (PW6) Fix this bit to "0." Functions 0 : P04 output 1 : PWM0 output 0 : P05 output 1 : PWM1 output 0 : P06 output 1 : PWM2 output 0 : P07 output 1 : PWM3 output 0 : P00 output 1 : PWM4 output 0: P01 output 1: PWM5 output 0: P02 output 1: PWM6 output After reset R W 0 RW 0 0 0 0 0 0 0 RW RW RW RW RW RW RW
PWM Mode Register 2
Address 020B16
121
MITSUBISHI MICROCOMPUTERS
. e. tion ang ifica t to ch pec c al s subje fin re a ot a is n limits his ic e: T rament ic Not e pa Som
P
REL
A IMIN
RY
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
Sync Pulse Counter Register
b7 b6 b5 b4 b3 b2 b1 b0 Sync pulse counter register (SYC) [Address 020F 16]
B 0 to 4 5
Name Count value (SYC0 to SYC4) Count source (SYC5)
Functions
After reset 0
RW R--
0: HSYNC signal 1: Composite sync signal
0
RW
6, 7 Nothing is assigned. These bits are write disable bits. When these bits are read out, the values are "0."
0
R--
Sync Pulse Counter Register
Address 020F16
Data Slicer Control Register 3
b7 b6 b5 b4 b3 b2 b1 b0 Data slicer control register 3 (DSC3) [Address 0210 16]
B 0
Bit Line selection bit for slice voltage (DSC30)
Functions 0: Main data slice line 1: Sub-data slice line b2 0 0 1 1 Field of subb1 data slice line 0 F2 1 F1 0 F1 and F2 1 F1 and F2 Field for setting refernce voltage F2 F1 F2 F1
After reset 0 0
RW RW RW
1, 2 Field to be sliced data selection bit (DSC31, DSC32)
3 to 7
Setting bit of sub-data slice line (DSC33 to DSC37)
0
RW
Definition of fields 1 (F1) and 2 (F2) F1 : Hsep VSYNC Vsep
F2 : Hsep VSYNC Vsep
Data Slicer Control Register 3
Address 021016
122
MITSUBISHI MICROCOMPUTERS
. e. tion ang ifica t to ch pec c al s subje fin re a ot a is n limits his ic e: T rament ic Not e pa Som
PRE
L
A IMIN
RY
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
Interrupt Input Polarity Register
b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 Interrupt input polarity register (IP) [Address 0212 16]
B
Name
Functions
After reset 0
RW RW RW RW RW
0 to 2, Fix these bits to "0." 5 3 4 6 INT1 polarity switch bit (INT1POL) INT2 polarity switch bit ( INT2POL) INT3 polarity switch bit ( INT3POL) A-D conversion * INT3 interrupt source selection bit (RE7) 0 : Positive polarity 1 : Negative polarity 0 : Positive polarity 1 : Negative polarity 0 : Positive polarity 1 : Negative polarity 0 : Positive polarity 1 : Negative polarity
0 0 0
7
0
RW
Interrupt Input Polarity Register
Address 021216
Serial I/O Mode Register
b7 b6 b5 b4 b3 b2 b1 b0 00 Serial I/O mode register (SM) [Address 0213 16] B Name b1 0 0 1 1 Functions b0 0: f(XIN)/4 or f(XCIN)/4 1: f(XIN)/16 or f(XCIN)/16 0: f(XIN)/32 or f(XCIN)/32 1: f(XIN)/64 or f(XCIN)/64 After reset R W 0 RW
0, 1 Internal synchronous clock selection bits (SM0, SM1)
2 3
Synchronous clock selection bit (SM2) Port function selection bit (SM3) Port function selection bit (SM4) Transfer direction selection bit (SM5)
0: External clock 1: Internal clock 0: P11, P13 1: SCL1, SDA1 0: P12, P14 1: SCL2, SDA2 0: LSB first 1: MSB first
0
RW
0
RW
4 5
0 0 0
RW RW RW
6, 7 Fix these bits to "0."
Serial I/O Mode Register
Address 021316
123
MITSUBISHI MICROCOMPUTERS
ion. hange c icat ecif ject to l sp fina re sub a not mits a is li This entic m ice: Not e para Som
PR
IN LIM E
ARY
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
Clock Source Control Register
b7 b6 b5 b4 b3 b2 b1 b0 Clock source control register (CS) [Address 021616]
B 0
Name CC mode clock selection bit (CS0)
Functions 0: Data slicer clock 1: OSC1 clock
b2 b1
After reset R W 0 0 RW RW
1, 2 OSD mode clock selection bits (CS1, CS2)
0 0 1 1
0: Data slicer clock 1: OSC1 clock 0: Main clock (See note 1) 1: Do not set 0 0 RW RW
3
EXOSD mode clock selection bit (CS3)
0: Data slicer clock 1: OSC1 clock
b5 b4
4, 5 OSD oscillating mode selection bits (CS4, CS5)
0 0 1 1
0: 32 kHz oscillating mode 1: Input ports P63, P64 (See note 2) 0: LC oscillating mode 1: Ceramic * quartz-crystal oscillating mode 0 0
6 7
Pre-divide ratio of layer 2 selection bit (CS6) Test bit (See note 3)
0: ! 1 1: ! 2
RW RW
Notes 1: When setting "102," main clock is set as a clock in the CC mode and EXOSD mode regardless of bits 0, 3. 2: When selecting input ports P63 and P64, set bit 7 at address 00C716 to "1." 3: Be sure to set bit 7 to "0" for program of the mask and the EPROM versions. For the emulator MCU version (M37274ERSS), be sure to set bit 7 to "1" when using the data slicer clock for software debugging.
Clock Source Control Register
Address 021616
124
MITSUBISHI MICROCOMPUTERS
. e. tion ang ifica t to ch pec c al s subje fin re a ot a is n limits his ic e: T rament ic Not e pa Som
PRE
L
A IMIN
RY
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
I/O Polarity Control Register
b7 b6 b5 b4 b3 b2 b1 b0 I/O polarity control register (PC) [Address 0217 16]
B 0 1 2 3 4 5 6
Name HSYNC input polarity switch bit (PC0) VSYNC input polarity switch bit (PC1) R, G, B output polarity switch bit (PC2)
Functions 0 : Positive polarity input 1 : Negative polarity input 0 : Positive polarity input 1 : Negative polarity input 0 : Positive polarity output 1 : Negative polarity output
After reset R W 0 0 0 0 0 0 0 RW RW RW R-- RW RW RW
Nothing is assigned. Ths bit is a write disable bit. When this bit is read out, the value is "0." OUT1 output polarity switch bit (PC4) OUT2 output polarity switch bit (PC5) Display dot line selection bit (PC6) (See note) 0 : Positive polarity output 1 : Negative polarity output 0 : Positive polarity output 1 : Negative polarity output 0:" " 1:" " " at even field " at odd field " at even field " at odd field
7
Field determination flag (PC7)
0 : Even field 1 : Odd field
1
R--
Note: Refer to the corresponding figure (P62).
I/O Polarity Control Register
Address 021716
Raster Color Register
b7 b6 b5 b4 b3 b2 b1 b0 00 Raster color register (RC) [Address 0218 16] B 0 1 2 Name Raster color R control bit (RC0) Raster color G control bit (RC1) Raster color B control bit (RC2) Functions 0 : No output 1 : Output 0 : No output 1 : Output 0 : No output 1 : Output After reset R W 0 0 0 0 0 0 0 RW RW RW R-- RW RW RW
3, 4 Nothing is assigned. These bits are write disable bits.
When these bits are read out, the values are "0."
5
Raster color OUT1 control bit (RC5)
0 : No output 1 : Output 0 : No output 1 : Output 0 : Interrupt occurs at end of OSD or EXOSD block display 1 : Interrupt occurs at end of CC mode block display
6 Raster color OUT2 control bit (RC6) 7 OSD interrupt source selection bit (RC7)
Raster Color Register
Address 021816
125
MITSUBISHI MICROCOMPUTERS
ion. hange c icat ecif ject to l sp fina re sub a not mits a is li This entic m ice: Not e para Som
PR
IN LIM E
ARY
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
Extra Font Color Register
b7 b6 b5 b4 b3 b2 b1 b0 00 Extra font color register (EC) [Address 0219 16] B 0 1 2 Name Extra font color R control bit (EC0) Extra font color G control bit (EC1) Extra font color B control bit (EC2) Functions 0 : No output 1 : Output 0 : No output 1 : Output 0 : No output 1 : Output After reset 0 0 0 0 0 RW RW RW RW RW R--
3, 4 Fix these bits to "0." Nothing is assigned. These bits are write disable bits. When these bits are read out, the values are "0."
5 to 7
Extra Font Color Register
Address 021916
Border Color Register
b7 b6 b5 b4 b3 b2 b1 b0 00 Border color register (FC) [Address 021B 16] B 0 1 2 Name Border color R control bit (FC0) Border color G control bit (FC1) Border color B control bit (FC2) Functions 0 : No output 1 : Output 0 : No output 1 : Output 0 : No output 1 : Output After reset 0 0 0 0 0 RW RW RW RW RW R--
3, 4 Fix these bits to "0." Nothing is assigned. These bits are write disable bits. When these bits are read out, the values are "0."
5 to 7
Border Color Register
Address 021B16
126
MITSUBISHI MICROCOMPUTERS
. e. tion ang ifica t to ch pec c al s subje fin re a ot a is n limits his ic e: T rament ic Not e pa Som
PRE
L
A IMIN
RY
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
Window H Register 1
b7 b6 b5 b4 b3 b2 b1 b0 Window H register 1 (WH1) [Address 021C 16] B Name Functions After reset RW
0 Control bits of window to top boundary 7 (WN10 to WN17) (See note 1)
Top boundary position (low-order 8 bits) Indeterminate R W TH ! (setting value of low-order 2 bits of WH2 ! 162 + setting value of high-order 4 bits of WH1 ! 161 + setting value of low-order 4 bits of WH1 ! 160)
Notes 1: Set values except "00 16" to the WH1 when WH2 is "00 16." 2: TH is cycle of HSYNC.
Window H Register 1
Address 021C16
Window L Register 1
b7 b6 b5 b4 b3 b2 b1 b0 Window L register 1 (WL1) [Address 021D 16] B Name Functions After reset RW
0 Control bits of window to top boundary 7 (WL10 to WL17) (See note 1)
Top boundary position (low-order 8 bits) Indeterminate R W TH ! (setting value of low-order 2 bits of WL2 ! 162 + setting value of high-order 4 bits of WL1 ! 161 + setting value of low-order 4 bits of WL1 ! 160)
Notes 1: Set values fit for the following condition: (WH1+WH2)<(WL1+WL2) 2: TH is cycle of HSYNC.
Window L Register 1
Address 021D16
Window H Register 2
b7 b6 b5 b4 b3 b2 b1 b0 Window H register 2 (WH2) [Address 021E 16] B Name Functions After reset RW
0, 1 Control bits of window top boundary (WN20 to WN27) (See note 1)
Top boundary position (high-order 2 bits) Indeterminate R W TH ! (setting value of low-order 2 bits of WH2 ! 162 + setting value of high-order 4 bits of WH1 ! 161 + setting value of low-order 4 bits of WH1 ! 160)
2 Nothing is assigned. These bits are write disable bits. Indeterminate R -- to When these bits are read out, the values are indeterminate. 7 Notes 1: Set values except "00 16" to the WH1 when WH2 is "00 16." 2: TH is cycle of HSYNC.
Window H Register 2
Address 021E16
127
MITSUBISHI MICROCOMPUTERS
ion. hange c icat ecif ject to l sp fina re sub a not mits a is li This entic m ice: Not e para Som
PR
IN LIM E
ARY
.
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
Window L Register 2
b7 b6 b5 b4 b3 b2 b1 b0 Window L register 2 (WL2) [Address 021F 16] B Name Functions After reset RW
0, 1 Control bits of window top boundary (WL20 to WL27) (See note 1)
Top boundary position (high-order 2 bits) Indeterminate R W TH ! (setting value of low-order 2 bits of WL2 ! 162 + setting value of high-order 4 bits of WL1 ! 161 + setting value of low-order 4 bits of WL1 ! 160)
2 Nothing is assigned. These bits are write disable bits. Indeterminate R -- to When these bits are read out, the values are indeterminate. 7 Notes 1: Set values fit for the following condition: (WH1+WH2)<(WL1+WL2) 2: TH is cycle of HSYNC.
Window L Register 2
Address 021F16
Vertical Position Register 1i
b7 b6 b5 b4 b3 b2 b1 b0 Vertical position register 1i (VP1i) (i = 1 to 12) [Addresses 0220
16
to 022B16]
B Name Functions After reset R W 0 Control bits of vertical Vertical display start positions Indeterminate R W to display start positions (low-order 8 bits) 7 (VP1i0 to VP1i7) TH ! (See note 1) (setting value of low-order 2 bits of VP2i ! 162 + setting value of low-order 4 bits of VP1i ! 161 + setting value of low-order 4 bits of VP1i ! 160) Notes 1: Set values except "00 16" "0116" to VP1i when VP2i is "00 16." 2: TH is cycle of HSYNC.
Vertical Position Register 1i
Addresses 022016 to 022B16
Vertical Position Register 2i
b7 b6 b5 b4 b3 b2 b1 b0 Vertical position register 2i (VP2i) (i = 1 to 12) [Addresses 0230
16
to 023B16]
B Name Functions After reset R W 0, 1 Control bits of vertical Vertical display start positions Indeterminate R W display start positions (high-order 2 bits) TH ! (VP1i0 to VP1i7) (See note 1) (setting value of low-order 2 bits of VP2i ! 162 + setting value of low-order 4 bits of VP1i ! 161 + setting value of low-order 4 bits of VP1i ! 160) 2 Nothing is assigned. These bits are write disable bits. to When these bits are read out, the values are indeterminate. 7 Indeterminate R --
Notes 1: Set values except "00 16" "0116" to VP1i when VP2i is "00 16." 2: TH is cycle of HSYNC.
Vertical Position Register 2i
Addresses 023016 to 023B16
128
MITSUBISHI MICROCOMPUTERS
. e. tion ang ifica t to ch pec c al s subje fin re a ot a is n limits his ic e: T rament ic Not e pa Som
PRE
L
A IMIN
RY
M37274MA-XXXSP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
ROM Correction Enable Register
b7 b6 b5 b4 b3 b2 b1 b0 0 0
ROM correction enable register (RCR) [Address 0246 B
0 1
16]
Name
Block 1 enable bit (RC0) Block 2 enable bit (RC1)
Functions
0: Disabled 1: Enabled 0: Disabled 1: Enabled
After reset R W
0 0
RW RW RW R--
2, 3 Fix these bits to "0."
0
4 to 7
Nothing is assigned. These bits are write disable bits. When these bits are read out, the values are "0."
0
ROM Correction Enable Register
Address 024616
129
Keep safety first in your circuit designs!
* Mitsubishi Electric Corporation puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of non-flammable material or (iii) prevention against any malfunction or mishap.
Notes regarding these materials
* * * These materials are intended as a reference to assist our customers in the selection of the Mitsubishi semiconductor product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Mitsubishi Electric Corporation or a third party. Mitsubishi Electric Corporation assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data, diagrams, charts or circuit application examples contained in these materials. All information contained in these materials, including product data, diagrams and charts, represent information on products at the time of publication of these materials, and are subject to change by Mitsubishi Electric Corporation without notice due to product improvements or other reasons. It is therefore recommended that customers contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor for the latest product information before purchasing a product listed herein. Mitsubishi Electric Corporation semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. The prior written approval of Mitsubishi Electric Corporation is necessary to reprint or reproduce in whole or in part these materials. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. Please contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor for further details on these materials or the products contained therein.
*
* *
*
(c) 1997 MITSUBISHI ELECTRIC CORP. New publication, effective Nov. 1997. Specifications subject to change without notice.
REVISION DESCRIPTION LIST
Rev. No. 1.0 2.0 First Edition
M37274MA-XXXSP DATA SHEET
Revision Description Rev. date 9706 971130
Information about copywright note, revision number, release date added (last page).
(1/1)