View MF0_4220423.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Approval Sheet
for
Metal Film Resistors
MF0 series
1%
YAGEO CORPORATION
Headquarters: 3F, No.233-1, Pao Chiao Rd., Hsin Tien, Taipei, Taiwan, R.O.C. Tel: 886-2-2917-7555 Fax: 886-2-2917-0100 URL: www.yageo.com
Page-1
1.
PRODUCT:
METAL FILM RESISTORS
2.
PART NUMBER:
Part number of the metal film resistor is identified by the name, power, tolerance, packing, temperature coefficient, special type and resistance value. Example
MF0
207
F
T
E
52-
100R
(1) (2) (3) (4) (5) (6) (7) Series Power Resistance Packing Temperature Special Resistance Coefficient Type Value Name Rating Tolerance Style of Resistance (1) Style: MFR SERIES (2) Power Rating 204 = 0.4W207 = 0.6W (3) Tolerance B=0.1% (4) Packaging Type: C=0.25% D=0.5% F=1%
RPaper Taping Reel TTape on Box Packing BBulk Packing D= 25PPM E = 50PPM
(5) Temperature CoefficientC= 15PPM (6) Special Type
26- = 26mm 52- = 52.4mm M = M-Type Forming for Bulk MT = M-Type Forming for Taping ( Rated 0204 size only ) FT = F-Type Forming for Taping ( Rated 0207 size only ) PN = PANAsert ( Rated 0207 size only ) AV = Avlsert ( Rated 0207 size only )
(7) Resistance ValueE24 & E96 Series ( for1% ) Example1R10R100R10K100K330K1M......
Page-2
3.
BAND-CODE:
COLOR BLACK BROWN RED ORANGE YELLOW GREEN BLUE VIOLET GREY WHITE GOLD SILVER
1ST BAND 0 1 2 3 4 5 6 7 8 9
2ND BAND 0 1 2 3 4 5 6 7 8 9
3ND BAND 0 1 2 3 4 5 6 7 8 9
MULTIPLIER 1 10 100 1K 10K 100K 1M 10M
TOLERANCE 1(F)
0.5 ( D ) 0.25 ( C ) 0.1 ( B )
0.1 0.01
4.
ELECTRICAL CHARACTERISTICS
STYLE MF0204 0.4W 200V 400V 300V - 55 to + 155 1 0 ~ 1 M for E24 & R96 series value 1 50 ppm / 0.2 MF0207 0.6W 300V 600V 500V
Power Rating at 70 Maximum Working Voltage Maximum Overload Voltage Dielectric Withstanding Voltage Operating Temp. Range Standard Value Range Minimum Value Range Temperature Coefficient
Standard resistance is 10~ 1M, below or over this resistance on request.
5.
DERATING CURVE
Rated Load (%)
100 80 60 40 20 20 40 60 80 100 120 140 155 180 70
Ambient Temperature ()
Page-3
6.
DIMENSIONS
d
H
L
D
Unitmm STYLE MF0204 MF0207 L 3.40.3 6.30.5 D 1.90.2 2.40.2 H 282.0 282.0 d 0.50.05 0.60.05
7.
ENVIRONMENTAL CHARACTERISTICS
(1) Short Time Over Load Test At 2.5 times of the rated voltage. ( If the voltage exceeds the maximum load voltage, the maximum load voltage will be used as the rated voltage ) applied for 5 seconds, the resistor should be free from defects after the resistor is released from load for about 30 minutes Short Time Overload Voltage =
2.5 * Power Rating x Resistance Value
The change of the resistance value should be within 0.25 % + 0.05 (2) Dielectric Withstanding Voltage The resistor is placed on the metal V Block. Apply a Table I dielectric withstanding between the terminals connected together with the block for about 60 seconds. The resistor shall be able to withstand without breakdown or flashover. (3) Temperature Coefficient Test Test of resistors above room temperature 100C 2C ( Testing Temperature 115C to 130C ) at the constant temperature silicon plate for over 5 minutes. Then measure the resistance value. The Temperature Coefficient is calculated by the following equation and its value should be within the range of requested.
Re sistor Temperatur e Coefficient =
R R0 t to
R - R0 1 x x 10 6 R0 t - t0
Resistance value under the testing temperature Resistance value at the room temperature The testing temperature Room temperature
(4) Insulation Resistance Apply test terminal on lead and resistor body. The test resistance should be high than 10,000M ohm.
Page-4
(5) Solderability Immerse the specimen into the solder pot at 235 5 C for 5 0.5 seconds. At least 95% solder coverage on the termination. (6) Resistance to Solvent The specimen into the appropriate solvent of IPA condition of ultrasonic machine for 1 minutes. The specimen is no deterioration of coatings and color code. (7) Terminal Strength Direct Load - Resistors shall be held by one terminal and the load shall be gradually applied in the direction of the longitudinal axis of the resistor unit the applied load reacheds 5 pounds The load shall be held for 10 seconds. The load of weight shall be 2.5 kg ( 24.5N ). (8) Pulse Overload Apply 4 times of rated voltage to the specimen at the 1 second on and 25 seconds off cycle, subjected to voltage application cycles specified in 10,000 time The change of the resistance value shall be within 1.0% + 0.05 (9) Load Life in Humidity Place the specimen in a test chamber at 40 2 C and 90 ~ 95 % relative humidity. Apply the rated voltage to the specimen at the 1.5 hours on and 0.5 hour off cycle. The total length of test is 1,000 hours The change of the resistance value shall be within 1.5 % + 0.05 (10) Load Life Test Placed in the constant temperature chamber of 70 3 C the resistor shall be connected to the lead wire at the point of 25mm. Length with each terminal, the resistors shall be arranged not much effected mutually by the temperature of the resistors and the excessive ventilation shall not be performed, for 90 minutes on and 30 minutes off under this condition the rated D.C. voltage is applied continuously for 1000+48/-0 hours then left at no-load for 1hour, measured at this time the resistance value The change of the resistance value shall be within 1.5 % + 0.05 . There shall be no remarkable change in the appearance and the color code shall be legible after the test. (11) Temperature Cycling Test The temperature cycle shown in the following table shall be repeated 5 times consecutively. The measurement of the resistance value is done before the first cycle and after ending the fifth cycle, leaving in the room temperature for about 1 hour Temperature Cycling Conditions: Step 1 2 3 4 Temperature(C) -55 3 25 3 155 3 25 3 Time (minute) 30 2~3 30 2~3
The change of the resistance value shall be within 0.75 % + 0.05 After the test the resistor shall be free from the electrical or mechanical damage. (12) Resistance to Soldering Heat The terminal lead shall be dipped into the solder pot at 350 10 C for 3 0.5 seconds up to 2 ~ 2.5 mm. The change of the resistance value shall be within 0.25 % + 0.05
Page-5
8.
PACKING METHODS
Bandolier for Axial leads
Unit:mm STYLE MF0204 MF0207 a 6 0.5 6 0.5 A 52.4 1.0 26.0 1.0 52.4 1.0 26.0 1.0 B1-B2 1.0 1.0 1.0 1.0 S (spacing) 5 5 T (max. deviation of spacing) 0.5 mm per 5 spacing 1 mm per 10 spacing
9.
TAPE ON REEL PACKING
STYLE MF0204 MF0207
ACROSS FLANGE ( A ) 72 72
Qty per reel 5,000 5,000
10. TAPE ON BOX PACKING
STYLE MF0204 MF0207
Standard Lead Length W(A) 81 81 H(B) 70 104 L(C) 260 260 48 48
Short Lead Length W(A) H(B) 102 102 L(C) 255 255
Qty per box 5,000 5,000
Page-6
11. SPECIAL TYPE ( FORMING DIMENSIONS )
M TYPE Forming for Bulk
UNITmm
STYLE MF0204 MF0207
L 3.4 0.3 6.3 0.5
D 1.9 0.2 2.4 0.2
d 0.5 0.05 0.6 0.05
P 6.0 1 10.0 1
H 10.0 1 10.0 1
MT Type Forming for Taping
( Rated 0204 size only )
FT Type Forming for Taping
( Rated 0207 size only )
Page-7
PN Type Forming for Taping
( Rated 0207 size only )
AV Type Forming for Taping
( Rated 0207 size only )
12. Plant Address
A. Taiwan Hsin Tien Plant 1F, No.5, Lane 560, Chung Cheng Road, Hsin Tien Taipei, Taiwan, ROC ( 560 5 1 ) Tel. 886-2-2218-2139 Fax. 886-2-2218-2138 China Dongguan Plant 7-1, Gaoli Road, Gaoli Industrial Zone Tangxia Zhen, Dongguan, Guangdong, China ( 7-1 ) Tel. 86-769-772 0275 Fax. 86-769-772 0295 China MuDu Plant No.158, Fengjiang Road, No.1 Building of NanBangIND.Zone, Mu Du New District, Suzhou, China ( 158 1 ) Tel. 86-512-66518889 Fax. 86-512-66519889
B.
C.
Page-8

▲Up To Search▲

Price & Availability of MF0

	To Download MF0 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .