|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
May 2007 HYB18T512400B[C/F] HYB18T512800B[C/F] HYB18T512160B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM DDR2 SDRAM RoHS Compliant Products Internet Data Sheet Rev. 1.1 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM HYB18T512400B[C/F], HYB18T512160B[C/F], HYB18T512800B[C/F] Revision History: 2007-05, Rev. 1.1 Page All All All Subjects (major changes since last revision) Adapted internet edition Added more product types Qimonda template update Previous Revision: 2007-01, Rev. 1.05 Previous Revision: 2006-02, Rev. 1.04 We Listen to Your Comments Any information within this document that you feel is wrong, unclear or missing at all? Your feedback will help us to continuously improve the quality of this document. Please send your proposal (including a reference to this document) to: techdoc@qimonda.com qag_techdoc_rev400 / 3.2 QAG / 2006-07-21 03292006-YBYM-WG0Z 2 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM 1 Overview This chapter gives an overview of the 512-Mbit Double-Data-Rate-Two SDRAM product family and describes its main characteristics. 1.1 Features The 512-Mbit Double-Data-Rate-Two SDRAM offers the following key features: * Off-Chip-Driver impedance adjustment (OCD) and On* 1.8 V 0.1 V Power Supply 1.8 V 0.1 V (SSTL_18) compatible I/O Die-Termination (ODT) for better signal quality * DRAM organizations with 4 and 8 data in/outputs * Auto-Precharge operation for read and write bursts * Double-Data-Rate-Two architecture: two data transfers * Auto-Refresh, Self-Refresh and power saving Powerper clock cycle four internal banks for concurrent operation Down modes * Programmable CAS Latency: 3, 4, 5 and 6 * Average Refresh Period 7.8 s at a TCASE lower than * Programmable Burst Length: 4 and 8 85 C, 3.9 s between 85 C and 95 C * Differential clock inputs (CK and CK) * Programmable self refresh rate via EMRS2 setting * Programmable partial array refresh via EMRS2 settings * Bi-directional, differential data strobes (DQS and DQS) are transmitted / received with data. Edge aligned with read * DCC enabling via EMRS2 setting * Full and reduced Strength Data-Output Drivers data and center-aligned with write data. * 1kB page size for x4 & x8, 2kB page size for x16 * DLL aligns DQ and DQS transitions with clock * Package: P(G)-TFBGA-60 and P(G)-TFBGA-84 * DQS can be disabled for single-ended data strobe operation * RoHS Compliant Products1) * Commands entered on each positive clock edge, data and * All Speed grades faster than DDR2-400 comply with data mask are referenced to both edges of DQS DDR2-400 timing specifications when run at a clock rate * Data masks (DM) for write data of 200 MHz. * Posted CAS by programmable additive latency for better command and data bus efficiency TABLE 1 Performance Table for -25F and -2.5 Product Type Speed Code Speed Grade Max. Clock Frequency @CL6 @CL5 @CL4 @CL3 Min. RAS-CAS-Delay Min. Row Precharge Time Min. Row Active Time Min. Row Cycle Time -25F DDR2-800D 5-5-5 -2.5 DDR2-800E 6-6-6 400 333 266 200 15 15 45 60 Unit -- MHz MHz MHz MHz ns ns ns ns fCK6 fCK5 fCK4 fCK3 tRCD tRP tRAS tRC 400 400 266 200 12.5 12.5 45 57.5 1) RoHS Compliant Product: Restriction of the use of certain hazardous substances (RoHS) in electrical and electronic equipment as defined in the directive 2002/95/EC issued by the European Parliament and of the Council of 27 January 2003. These substances include mercury, lead, cadmium, hexavalent chromium, polybrominated biphenyls and polybrominated biphenyl ethers. Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 3 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM TABLE 2 Performance table for -3(S) Product Type Speed Code Speed Grade Max. Clock Frequency @CL5 @CL4 @CL3 Min. RAS-CAS-Delay Min. Row Precharge Time Min. Row Active Time Min. Row Cycle Time -3 DDR2-667C 4-4-4 -3S DDR2-667D 5-5-5 333 266 200 15 15 45 60 Unit -- MHz MHz MHz ns ns ns ns fCK5 fCK4 fCK3 tRCD tRP tRAS tRC 333 333 200 12 12 45 57 TABLE 3 Performance Table for -3.7(F) Product Type Speed Code Speed Grade Max. Clock Frequency @CL5 @CL4 @CL3 Min. RAS-CAS-Delay Min. Row Precharge Time Min. Row Active Time Min. Row Cycle Time -37F DDR2-533B 3-3-3 -3.7 DDR2-533C 4-4-4 266 266 200 15 15 45 60 Unit -- MHz MHz MHz ns ns ns ns fCK5 fCK4 fCK3 tRCD tRP tRAS tRC 266 266 266 11.25 11.25 45 56.25 TABLE 4 Performance Table for -5 Product Type Speed Code Speed Grade Max. Clock Frequency @CL5 @CL4 @CL3 Min. RAS-CAS-Delay Min. Row Precharge Time Min. Row Active Time Min. Row Cycle Time -5 DDR2-400B 3-3-3 Units -- MHz MHz MHz ns ns ns ns fCK5 fCK4 fCK3 tRCD tRP tRAS tRC 200 200 200 15 15 40 55 Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 4 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM 1.2 Description latched at the cross point of differential clocks (CK rising and CK falling). All I/Os are synchronized with a single ended DQS or differential DQS-DQS pair in a source synchronous fashion. A 16-bit address bus for x4 and x8 organized components and a 15-bit address bus for x16 components is used to convey row, column and bank address information in a RASCAS multiplexing style. The DDR2 device operates with a 1.8 V 0.1 V power supply. An Auto-Refresh and Self-Refresh mode is provided along with various power-saving power-down modes. The functionality described and the timing specifications included in this data sheet are for the DLL Enabled mode of operation. The DDR2 SDRAM is available in FBGA package. The 512-Mb DDR2 DRAM is a high-speed Double-DataRate-Two CMOS DRAM device containing 536,870,912 bits and is internally configured as an quad-bank DRAM. The 512-Mb device is organized as either 32 Mbit x 4 I/O x4 banks, 16 Mbit x8 I/O x 4 banks or 8 Mbit x16 I/O x4 banks chip. These devices achieve high speed transfer rates starting at 400 Mb/sec/pin for general applications. See Table 1 for performance figures. The device is designed to comply with all DDR2 DRAM key features: 1. Posted CAS with additive latency 2. Write latency = read latency - 1 3. Normal and weak strength data-output driver 4. Off-Chip Driver (OCD) impedance adjustment 5. On-Die Termination (ODT) function All of the control and address inputs are synchronized with a pair of externally supplied differential clocks. Inputs are Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 5 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM TABLE 5 Ordering Information for Lead-Free Products (RoHS Compliant) Product Type HYB18T512400BF-2.5 HYB18T512800BF-2.5 HYB18T512160BF-2.5 Org. Speed x4 x8 x16 CAS-RCD-RP Latencies1)2)3) Clock (MHz) Package 400 400 400 400 400 400 333 333 333 333 333 333 266 266 266 200 200 200 PG-TFBGA60 PG-TFBGA60 PG-TFBGA84 PG-TFBGA60 PG-TFBGA60 PG-TFBGA84 PG-TFBGA60 PG-TFBGA60 PG-TFBGA84 PG-TFBGA60 PG-TFBGA60 PG-TFBGA84 PG-TFBGA60 PG-TFBGA60 PG-TFBGA84 PG-TFBGA60 PG-TFBGA60 PG-TFBGA84 Note 4) DDR2-800E 6-6-6 DDR2-800E 6-6-6 DDR2-800E 6-6-6 DDR2800D DDR2800D DDR2800D DDR2667D DDR2667D DDR2667D DDR2667C DDR2667C DDR2667C DDR2533C DDR2533C DDR2533C 5-5-5 5-5-5 5-5-5 5-5-5 5-5-5 5-5-5 4-4-4 4-4-4 4-4-4 4-4-4 4-4-4 4-4-4 HYB18T512400BF-25F x4 HYB18T512800BF-25F x8 HYB18T512160BF-25F x16 HYB18T512400BF-3S HYB18T512800BF-3S HYB18T512160BF-3S HYB18T512400BF-3 HYB18T512800BF-3 HYB18T512160BF-3 HYB18T512400BF-3.7 HYB18T512800BF-3.7 HYB18T512160BF-3.7 HYB18T512400BF-5 HYB18T512800BF-5 HYB18T512160BF-5 1) 2) 3) 4) x4 x8 x16 x4 x8 x16 x4 x8 x16 x4 x8 x16 DDR2-400B 3-3-3 DDR2-400B 3-3-3 DDR2-400B 3-3-3 CAS: Column Address Strobe RCD: Row Column Delay RP: Row Precharge RoHS Compliant Product: Restriction of the use of certain hazardous substances (RoHS) in electrical and electronic equipment as defined in the directive 2002/95/EC issued by the European Parliament and of the Council of 27 January 2003. These substances include mercury, lead, cadmium, hexavalent chromium, polybrominated biphenyls and polybrominated biphenyl ethers. Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 6 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM TABLE 6 Ordering Information for Lead-Containing Products Product Type HYB18T512800BC-3S HYB18T512160BC-3S HYB18T512800BC-3.7 HYB18T512160BC-3.7 Org. x8 x16 x8 x16 Speed DDR2-667D DDR2-667D DDR2-533C DDR2-533C CAS-RCD-RP Latencies1)2)3) 5-5-5 5-5-5 4-4-4 4-4-4 Clock (MHz) 333 333 266 266 Package P-TFBGA-60 P-TFBGA-84 P-TFBGA-60 P-TFBGA-84 1) CAS: Column Address Strobe 2) RCD: Row Column Delay 3) RP: Row Precharge Note: For product nomenclature see Chapter 9 of this data sheet Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 7 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM 2 2.1 Chip Configuration Chip Configuration This chapter contains the chip configuration and addressing. The chip configuration of a DDR2 SDRAM is listed by function in Table 7. The abbreviations used in the Ball# and Buffer Type columns are explained in Table 8 and Table 9 respectively. The ball numbering for the FBGA package is depicted in Figure 1 for x4, Figure 2 for x8 and Figure 3 for x16. TABLE 7 Chip Configuration of DDR2 SDRAM Ball# Name Ball Type I I I I I I Buffer Type SSTL SSTL SSTL SSTL SSTL SSTL Clock Enable Clock Signal CK, Complementary Clock Signal CK Note: See functional description in x4/x8 organization Clock Enable Note: See functional description in x4/x8 organization Row Address Strobe (RAS), Column Address Strobe (CAS), Write Enable (WE) Chip Select Row Address Strobe (RAS), Column Address Strobe (CAS), Write Enable (WE) Chip Select Bank Address Bus 1:0 Function Clock Signals x4/x8 organization E8 F8 F2 J8 K8 K2 CK CK CKE CK CK CKE Clock Signal CK, Complementary Clock Signal CK Clock Signals x16 organization Control Signals x4/x8 organizations F7 G7 F3 G8 K7 L7 K3 L8 G2 G3 RAS CAS WE CS RAS CAS WE CS BA0 BA1 I I I I I I I I I I SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL Control Signals x16 organization Address Signals x4/x8 organizations Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 8 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM Ball# H8 H3 H7 J2 J8 J3 J7 K2 K8 K3 H2 K7 L2 L8 Name A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 AP A11 A12 A13 NC Ball Type I I I I I I I I I I I I I I I -- I I -- I I I I I I I I I I I I I I I/O I/O I/O I/O Buffer Type SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL -- SSTL SSTL -- SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL Function Address Signal 12:0, Address Signal 10/Autoprecharge Address Signal 13 Note: x4/x8 512 Mbit components Note: and x16 512 Mbit components Bank Address Bus 1:0 Address Signals x16 organization L2 L3 L1 M8 M3 M7 N2 N8 N3 N7 P2 P8 P3 M2 P7 R2 C8 C2 D7 D3 BA0 BA1 NC A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 AP A11 A12 DQ0 DQ1 DQ2 DQ3 Address Signal 12:0, Address Signal 10/Autoprecharge Data Signals x4/x8 organization Data Signal 3:0 Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 9 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM Ball# D1 D9 B1 B9 G8 G2 H7 H3 H1 H9 F1 F9 C8 C2 D7 D3 D1 D9 B1 B9 B7 A8 B3 A2 B7 A8 F7 E8 B3 B3 F3 Name DQ4 DQ5 DQ6 DQ7 DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8 DQ9 DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 DQS DQS RDQS RDQS UDQS UDQS LDQS LDQS DM UDM LDM Ball Type I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O O O I/O I/O I/O I/O I I I PWR Buffer Type SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL SSTL -- Function Data Signal 7:4 Data Signals x16 organization Data Signal 15:0 Data Strobe x4/x8 organizations Data Strobe Data Strobe x8 organisation Read Data Strobe Data Strobe x16 organization Data Strobe Upper Byte Data Strobe Lower Byte Data Mask x4/x8 organizations Data Mask Data Mask Upper/Lower Byte Data Mask x16 organization Power Supplies x4x8x16 organization A9, C1, C3, C7, VDDQ C9 I/O Driver Power Supply Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 10 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM Ball# A1 Name Ball Type PWR PWR PWR AI PWR PWR PWR PWR AI PWR PWR PWR PWR PWR PWR Buffer Type -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Function Power Supply I/O Driver Power Supply Power Supply I/O Reference Voltage Power Supply Power Supply Power Supply Power Supply I/O Reference Voltage I/O Driver Power Supply Power Supply Power Supply I/O Driver Power Supply Power Supply Power Supply VDD A7, B2, B8, D2, VSSQ D8 A3, E3 E2 E1 E9, H9, L1 E7 J1, K9 J2 VSS VREF VDDL VDD VSSDL VSS Power Supplies x4/x8 organizations Power Supplies x16 organization VREF E9, G1, G3, G7, VDDQ G9 J1 VDDL E1, J9, M9, R1 VDD E7, F2, F8, H2, VSSQ H8 J7 VSSDL A3, E3, J3, N1, VSS P9 Not Connected x4/x8 organization G1, L3,L7, L8 NC NC NC -- -- Not Connected Not Connected Not Connected x4 organization A2, B1, B9, D1, NC D9 A2, E2, L1, R3, NC R7, R8 F9 K9 ODT ODT Not Connected x16 organization NC -- Not Connected Other Balls x4/x8 organizations I I SSTL SSTL On-Die Termination Control On-Die Termination Control Other Balls x16 organization Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 11 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM TABLE 8 Abbreviations for Ball Type Abbreviation I O I/O AI PWR GND NC Description Standard input-only ball. Digital levels. Output. Digital levels. I/O is a bidirectional input/output signal. Input. Analog levels. Power Ground Not Connected TABLE 9 Abbreviations for Buffer Type Abbreviation SSTL LV-CMOS CMOS OD Description Serial Stub Terminated Logic (SSTL_18) Low Voltage CMOS CMOS Levels Open Drain. The corresponding ball has 2 operational states, active low and tristate, and allows multiple devices to share as a wire-OR. Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 12 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM Chip Configuration for x4 components, PG-TFBGA-60 (top view) FIGURE 1 Notes 1. VDDL and VSSDL are power and ground for the DLL. VDDL is connected to VDD on the device. VDD, VDDQ, VSSDL, VSS, and VSSQ are isolated on the device. 2. Ball position L8 is A13 for 512-Mbit and is Not Connected on 256-Mbit Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 13 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM Chip Configuration for x8 components, PG-TFBGA-60 (top view) FIGURE 2 Notes 1. RDQS / RDQS are enabled by EMRS(1) command. 2. If RDQS / RDQS is enabled, the DM function is disabled 3. When enabled, RDQS & RDQS are used as strobe signals during reads. 4. VDDL and VSSDL are power and ground for the DLL. VDDL is connected to VDD on the device. VDD, VDDQ, VSSDL, VSS, and VSSQ are isolated on the device. 5. Ball position L8 is A13 for 512-Mbit and is Not Connected on 256-Mbit. Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 14 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM Chip Configuration for x16 components, PG-TFBGA-84 (top view) FIGURE 3 Notes 1. UDQS/UDQS is data strobe for DQ[15:8], LDQS/LDQS is data strobe for DQ[7:0] 2. LDM is the data mask signal for DQ[7:0], UDM is the data mask signal for DQ[15:8] 3. VDDL and VSSDL are power and ground for the DLL. VDDL is connected to VDD on the device. VDD, VDDQ, VSSDL, VSS, and VSSQ are isolated on the device. Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 15 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM 2.2 Addressing TABLE 10 DDR2 Addressing for x4 Organization This chapter describes the addressing. Configuration Bank Address Number of Banks Auto-Precharge Row Address Column Address Number of Column Address Bits Number of I/Os Page Size [Bytes] 1) Referred to as 'org' 2) Referred to as 'colbits' 3) PageSize = 2colbits x org/8 [Bytes] x128Mb x 4 BA[1:0] 4 A10 / AP A[13:0] A11, A[9:0] 11 4 1024 (1K) 1) Note 2) 3) TABLE 11 DDR2 Addressing for x8 Organization Configuration Bank Address Number of Banks Auto-Precharge Row Address Column Address Number of Column Address Bits Number of I/Os Page Size [Bytes] 1) Referred to as 'org' 2) Referred to as 'colbits' 3) PageSize = 2colbits x org/8 [Bytes] x64Mb x 8 BA[1:0] 4 A10 / AP A[13:0] A[9:0] 10 8 1024 (1K) 1) Note 2) 3) Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 16 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM TABLE 12 DDR2 Addressing for x16 Organization Configuration Bank Address Number of Banks Auto-Precharge Row Address Column Address Number of Column Address Bits Number of I/Os Page Size [Bytes] 1) Referred to as 'org' 2) Referred to as 'colbits' 3) PageSize = 2colbits x org/8 [Bytes] x32Mb x 161) BA[1:0] 4 A10 / AP A[12:0] A[9:0] 10 16 2048 (2K) Note 2) 3) Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 17 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM 3 Functional Description This chapter contains the functional description. TABLE 13 Mode Register Definition (BA[2:0] = 000B) Field BA2 Bits 16 Type1) reg. addr. Description Bank Address [2] Note: BA2 not available on 256 Mbit and 512 Mbit components 0B BA1 BA0 A13 15 14 13 BA2 Bank Address Bank Address [1] BA1 Bank Address 0B Bank Address [0] 0B BA0 Bank Address Address Bus[13] Note: A13 is not available for 256 Mbit and x16 512 Mbit configuration 0B PD 12 w A13 Address bit 13 Active Power-Down Mode Select 0B PD Fast exit 1B PD Slow exit Write Recovery2) Note: All other bit combinations are illegal. 001B 010B 011B 100B 101B DLL 8 w WR 2 WR 3 WR 4 WR 5 WR 6 WR [11:9] w DLL Reset 0B DLL No 1B DLL Yes Test Mode 0B TM Normal Mode 1B TM Vendor specific test mode TM 7 w Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 18 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM Field CL Bits [6:4] Type1) w Description CAS Latency Note: All other bit combinations are illegal. 011B 100B 101B 110B 111B CL 3 CL 4 CL 5 CL 6 CL 7 BT 3 w Burst Type 0B BT Sequential BT Interleaved 1B Burst Length Note: All other bit combinations are illegal. 010B BL 4 011B BL 8 BL [2:0] w 1) w = write only register bits 2) Number of clock cycles for write recovery during auto-precharge. WR in clock cycles is calculated by dividing tWR (in ns) by tCK (in ns) and rounding up to the next integer: WR [cycles] tWR (ns) / tCK (ns). The mode register must be programmed to fulfill the minimum requirement for the analogue tWR timing WRMIN is determined by tCK.MAX and WRMAX is determined by tCK.MIN. TABLE 14 Extended Mode Register Definition (BA[2:0] = 001B) Field BA2 Bits 16 Type1) reg. addr. Description Bank Address [2] Note: BA2 not available on 256 Mbit and 512 Mbit components 0B BA1 BA0 A13 15 14 13 w BA2 Bank Address Bank Address [1] BA1 Bank Address 0B Bank Address [0] 1B BA0 Bank Address Address Bus [13] Note: A13 is not available for 256 Mbit and x16 512 Mbit configuration 0B Qoff 12 w A13 Address bit 13 Output Disable 0B QOff Output buffers enabled 1B QOff Output buffers disabled Read Data Strobe Output (RDQS, RDQS) RDQS Disable 0B 1B RDQS Enable RDQS 11 w Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 19 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM Field DQS Bits 10 Type1) w Description Complement Data Strobe (DQS Output) 0B DQS Enable DQS Disable 1B Off-Chip Driver Calibration Program 000B OCD OCD calibration mode exit, maintain setting 001B OCD Drive (1) 010B OCD Drive (0) 100B OCD Adjust mode 111B OCD OCD calibration default Additive Latency Note: All other bit combinations are illegal. 000B 001B 010B 011B 100B 101B AL 0 AL 1 AL 2 AL 3 AL 4 AL 5 OCD [9:7] Program w AL [5:3] w RTT 6,2 w Nominal Termination Resistance of ODT Note: See Table 25 "ODT DC Electrical Characteristics" on Page 28 00B 01B 10B 11B RTT (ODT disabled) RTT 75 Ohm RTT 150 Ohm RTT 50 Ohm DIC 1 w Off-chip Driver Impedance Control DIC Full (Driver Size = 100%) 0B 1B DIC Reduced DLL Enable 0B DLL Enable 1B DLL Disable DLL 0 w 1) w = write only register bits Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 20 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM TABLE 15 EMRS(2) Programming Extended Mode Register Definition (BA[2:0]=010B) Field BA Bits [15:14] Type1) w Description Bank Adress 00B BA MRS 01B BA EMRS(1) 10B BA EMRS(2) 11B BA EMRS(3): Reserved Address Bus, High Temperature Self Refresh Rate for TCASE > 85C 0B A7 disable 1B A7 enable 2) Address Bus 000B A Address bits Address Bus, Duty Cycle Correction (DCC) A3 DCC disabled 0B 1B A3 DCC enabled Address Bus, Partial Array Self Refresh for 4 Banks3) Note: Only for 256 Mbit and 512 Mbit components 000B 001B 010B 011B 100B 101B 110B 111B Partial Self Refresh for 8 banks PASR [2:0] w Address Bus, Partial Array Self Refresh for 8 Banks3) Note: Only for 1G and 2G components 000B 001B 010B 011B 100B 101B 110B 111B PASR0 Full Array PASR1 Half Array (BA[2:0]=000, 001, 010 & 011) PASR2 Quarter Array (BA[2:0]=000, 001) PASR3 1/8 array (BA[2:0] = 000) PASR4 3/4 array (BA[2:0]= 010, 011, 100, 101, 110 & 111) PASR5 Half array (BA[2:0]=100, 101, 110 & 111) PASR6 Quarter array (BA[2:0]= 110 & 111) PASR7 1/8 array(BA[2:0]=111) PASR0 Full Array PASR1 Half Array (BA[1:0]=00, 01) PASR2 Quarter Array (BA[1:0]=00) PASR3 Not defined PASR4 3/4 array (BA[1:0]=01, 10, 11) PASR5 Half array (BA[1:0]=10, 11) PASR6 Quarter array (BA[1:0]=11) PASR7 Not defined SRF 7 w A DCC [6:4] 3 w w Partial Self Refresh for 4 banks PASR [2:0] w 1) w = write only 2) When DRAM is operated at 85C TCase 95C the extended self refresh rate must be enabled by setting bit A7 to "1" before the self refresh mode can be entered. 3) If PASR (Partial Array Self Refresh) is enabled, data located in areas of the array beyond the specified location will be lost if self refresh is entered. Data integrity will be maintained if tREF conditions are met and no Self Refresh command is issued Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 21 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM TABLE 16 EMR(3) Programming Extended Mode Register Definition(BA[2:0]=011B) Field BA2 Bits 16 Type1) reg.addr Description Bank Address[2] Note: BA2 is not available on 256 Mbit and 512 Mbit components 0B BA1 BA0 A 15 14 [13:0] w BA2 Bank Address Bank Adress[1] 1B BA1 Bank Address Bank Adress[0] BA0 Bank Address 1B Address Bus[13:0] Note: A13 is not available for 256 Mbit and x16 512 Mbit configuration 00000000000000BA[13:0] Address bits 1) w = write only Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 22 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM TABLE 17 ODT Truth Table Input Pin x4 Components DQ[3:0] DQS DQS DM x8 Components DQ[7:0] DQS DQS RDQS RDQS DM x16 Components DQ[7:0] DQ[15:8] LDQS LDQS UDQS UDQS LDM UDM X X X 0 X 0 X X X X X X 0 X 0 X X 1 1 0 X X 0 X X EMRS(1) Address Bit A10 EMRS(1) Address Bit A11 Note: X = don't care; 0 = bit set to low; 1 = bit set to high Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 23 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM TABLE 18 Burst Length and Sequence Burst Length 4 Starting Address (A2 A1 A0) x00 x01 x1 0 x1 1 8 000 001 010 011 100 101 110 111 Sequential Addressing (decimal) 0, 1, 2, 3 1, 2, 3, 0 2, 3, 0, 1 3, 0, 1, 2 0, 1, 2, 3, 4, 5, 6, 7 1, 2, 3, 0, 5, 6, 7, 4 2, 3, 0, 1, 6, 7, 4, 5 3, 0, 1, 2, 7, 4, 5, 6 4, 5, 6, 7, 0, 1, 2, 3 5, 6, 7, 4, 1, 2, 3, 0 6, 7, 4, 5, 2, 3, 0, 1 7, 4, 5, 6, 3, 0, 1, 2 Interleave Addressing (decimal) 0, 1, 2, 3 1, 0, 3, 2 2, 3, 0, 1 3, 2, 1, 0 0, 1, 2, 3, 4, 5, 6, 7 1, 0, 3, 2, 5, 4, 7, 6 2, 3, 0, 1, 6, 7, 4, 5 3, 2, 1, 0, 7, 6, 5, 4 4, 5, 6, 7, 0, 1, 2, 3 5, 4, 7, 6, 1, 0, 3, 2 6, 7, 4, 5, 2, 3, 0, 1 7, 6, 5, 4, 3, 2, 1, 0 Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 24 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM 4 Truth Tables The truth tables in this chapter summarize the commands and there signal coding to control a standard Double-Data-Rate-Two SDRAM. TABLE 19 Command Truth Table Function CKE Previous Cycle (Extended) Mode Register Set Auto-Refresh Self-Refresh Entry Self-Refresh Exit Single Bank Precharge Precharge all Banks Bank Activate Write Write with AutoPrecharge Read Read with AutoPrecharge No Operation Device Deselect Power Down Entry Power Down Exit H H H L H H H H H H H H H H L Current Cycle H H L H H H H H H H H X X L H L L L H L L L L L L L L L H H L H L L L L X H L L L H H H H H X X H X H CS RAS CAS WE BA0 BA1 A[12:11] A10 A[9:0] Note1)2)3) L L L X H H H H L L L L H X X H X H L H H X H L L H L L H H H X X H X H BA X X X BA X BA BA BA BA BA X X X X OP Code X X X X X Column Column Column Column X X X X X X X L H L H L H X X X X X X X X X Column Column Column Column X X X X 4)5) 4) 4)6) 4)6)7) 4)5) 4) 4)5) 4)5)8) 4)5)8) Row Address 4)5)8) 4)5)8) 4) 4) 4)9) 4)9) 1) The state of ODT does not affect the states described in this table. The ODT function is not available during Self Refresh. 2) "X" means "H or L (but a defined logic level)". 3) Operation that is not specified is illegal and after such an event, in order to guarantee proper operation, the DRAM must be powered down and then restarted through the specified initialization sequence before normal operation can continue. 4) All DDR2 SDRAM commands are defined by states of CS, WE, RAS, CAS, and CKE at the rising edge of the clock. 5) Bank addresses BA[1:0] determine which bank is to be operated upon. For (E)MRS BA[1:0] selects an (Extended) Mode Register. 6) VREF must be maintained during Self Refresh operation. 7) Self Refresh Exit is asynchronous. 8) Burst reads or writes at BL = 4 cannot be terminated. 9) The Power Down Mode does not perform any refresh operations. The duration of Power Down is therefore limited by the refresh requirements. Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 25 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM TABLE 20 Clock Enable (CKE) Truth Table for Synchronous Transitions Current State1) CKE Previous Cycle6) (N-1) Power-Down Self Refresh Bank(s) Active All Banks Idle L L L L H H H Any State other H than listed above 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) Current Cycle6) (N) L H L H L L L H Command (N)2) 3) RAS, CAS, WE Action (N)2) Note4)5) X DESELECT or NOP X DESELECT or NOP DESELECT or NOP DESELECT or NOP AUTOREFRESH Maintain Power-Down Power-Down Exit Maintain Self Refresh Self Refresh Exit Active Power-Down Entry Precharge Power-Down Entry Self Refresh Entry 7)8)11) 7)9)10)11) 8)11)12) 9)11)12)13)14) 7)9)10)11)15) 9)10)11)15) 7)11)14)16) 17) Refer to the Command Truth Table 12) 13) 14) 15) 16) 17) Current state is the state of the DDR2 SDRAM immediately prior to clock edge N. Command (N) is the command registered at clock edge N, and Action (N) is a result of Command (N) The state of ODT does not affect the states described in this table. The ODT function is not available during Self Refresh. CKE must be maintained HIGH while the device is in OCD calibration mode. Operation that is not specified is illegal and after such an event, in order to guarantee proper operation, the DRAM must be powered down and then restarted through the specified initialization sequence before normal operation can continue. CKE (N) is the logic state of CKE at clock edge N; CKE (N-1) was the state of CKE at the previous clock edge. The Power-Down Mode does not perform any refresh operations. The duration of Power-Down Mode is therefor limited by the refresh requirements "X" means "don't care (including floating around VREF)" in Self Refresh and Power Down. However ODT must be driven HIGH or LOW in Power Down if the ODT function is enabled (Bit A2 or A6 set to "1" in EMRS(1)). All states and sequences not shown are illegal or reserved unless explicitly described elsewhere in this document. Valid commands for Power-Down Entry and Exit are NOP and DESELECT only. tCKE.MIN of 3 clocks means CKE must be registered on three consecutive positive clock edges. CKE must remain at the valid input level the entire time it takes to achieve the 3 clocks of registration. Thus, after any CKE transition, CKE may not transition from its valid level during the time period of tIS + 2 x tCK + tIH. VREF must be maintained during Self Refresh operation. On Self Refresh Exit DESELECT or NOP commands must be issued on every clock edge occurring during the tXSNR period. Read commands may be issued only after tXSRD (200 clocks) is satisfied. Valid commands for Self Refresh Exit are NOP and DESELCT only. Power-Down and Self Refresh can not be entered while Read or Write operations, (Extended) mode Register operations, Precharge or Refresh operations are in progress. Self Refresh mode can only be entered from the All Banks Idle state. Must be a legal command as defined in the Command Truth Table. TABLE 21 Data Mask (DM) Truth Table Name (Function) Write Enable Write Inhibit 1) Used to mask write data; provided coincident with the corresponding data. DM L H DQs Valid X Note 1) 1) Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 26 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM 5 5.1 Electrical Characteristics Absolute Maximum Ratings TABLE 22 Absolute Maximum Ratings This chapter describes the electrical characteristics. Caution is needed not to exceed absolute maximum ratings of the DRAM device listed in Table 22 at any time. Symbol Parameter Rating Min. Max. +2.3 +2.3 +2.3 +2.3 Unit Note Storage Temperature -55 +100 1) When VDD and VDDQ and VDDL are less than 500 mV; VREF may be equal to or less than 300 mV. 2) Storage Temperature is the case surface temperature on the center/top side of the DRAM. VDD VDDQ VDDL VIN, VOUT TSTG Voltage on VDD pin relative to VSS Voltage on VDDQ pin relative to VSS Voltage on VDDL pin relative to VSS Voltage on any pin relative to VSS -1.0 -0.5 -0.5 -0.5 V V V V C 1) 1)2) 1)2) 1) 1)2) Attention: Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. TABLE 23 DRAM Component Operating Temperature Range Symbol Parameter Rating Min. Max. 95 C 1)2)3)4) Unit Note TOPER Operating Temperature 0 1) Operating Temperature is the case surface temperature on the center / top side of the DRAM. 2) The operating temperature range are the temperatures where all DRAM specification will be supported. During operation, the DRAM case temperature must be maintained between 0 - 95 C under all other specification parameters. 3) Above 85 C the Auto-Refresh command interval has to be reduced to tREFI= 3.9 s 4) When operating this product in the 85 C to 95 C TCASE temperature range, the High Temperature Self Refresh has to be enabled by setting EMR(2) bit A7 to "1". When the High Temperature Self Refresh is enabled there is an increase of IDD6 by approximately 50 % Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 27 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM 5.2 DC Characteristics TABLE 24 Recommended DC Operating Conditions (SSTL_18) Symbol Parameter Rating Min. Typ. 1.8 1.8 1.8 0.5 x VDDQ Max. 1.9 1.9 1.9 0.51 x VDDQ Unit Note VDD VDDDL VDDQ VREF VTT 1) 2) 3) 4) Supply Voltage Supply Voltage for DLL Supply Voltage for Output Input Reference Voltage 1.7 1.7 1.7 0.49 x VDDQ V V V V 1) 1) 1) 2)3) 4) Termination Voltage VREF - 0.04 VREF VREF + 0.04 V VDDQ tracks with VDD, VDDDL tracks with VDD. AC parameters are measured with VDD, VDDQ and VDDDL tied together. The value of VREF may be selected by the user to provide optimum noise margin in the system. Typically the value of VREF is expected to be about 0.5 x VDDQ of the transmitting device and VREF is expected to track variations in VDDQ. Peak to peak ac noise on VREF may not exceed 2 % VREF (dc) VTT is not applied directly to the device. VTT is a system supply for signal termination resistors, is expected to be set equal to VREF, and must track variations in die dc level of VREF. TABLE 25 ODT DC Electrical Characteristics Parameter / Condition Termination resistor impedance value for EMRS(1)[A6,A2] = [0,1]; 75 Ohm Termination resistor impedance value for EMRS(1)[A6,A2] =[1,0]; 150 Ohm Termination resistor impedance value for EMRS(1)(A6,A2)=[1,1]; 50 Ohm Deviation of VM with respect to VDDQ / 2 1) Symbol Rtt1(eff) Rtt2(eff) Rtt3(eff) delta VM Min. 60 120 40 -6.00 Nom. 75 150 50 -- Max. 90 180 60 + 6.00 Unit % Note 1) 1) 1) 2) Measurement Definition for Rtt(eff): Apply VIH(ac) and VIL(ac) to test pin separately, then measure current I(VIHac) and I(VILac) respectively. Rtt(eff) = (VIH(ac) - VIL(ac)) /(I(VIHac) - I(VILac)). 2) Measurement Definition for VM: Turn ODT on and measure voltage (VM) at test pin (midpoint) with no load: delta VM = ((2 x VM / VDDQ) - 1) x 100 % TABLE 26 Input and Output Leakage Currents Symbol Parameter / Condition Input Leakage Current; any input 0 V < VIN < VDD Output Leakage Current; 0 V < VOUT < VDDQ Min. -2 -5 Max. +2 +5 Unit A A Note 1) 2) IIL IOL 1) All other pins not under test = 0 V 2) DQ's, LDQS, LDQS, UDQS, UDQS, DQS, DQS, RDQS, RDQS are disabled and ODT is turned off. Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 28 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM 5.3 DC & AC Characteristics In differential mode, these timing relationships are measured relative to the crosspoint of DQS and its complement, DQS. This distinction in timing methods is verified by design and characterization but not subject to production test. In single ended mode, the DQS (and RDQS) signals are internally disabled and don't care. DDR2 SDRAM pin timing are specified for either single ended or differential mode depending on the setting of the EMRS(1) "Enable DQS" mode bit; timing advantages of differential mode are realized in system design. The method by which the DDR2 SDRAM pin timing are measured is mode dependent. In single ended mode, timing relationships are measured relative to the rising or falling edges of DQS crossing at VREF. TABLE 27 DC & AC Logic Input Levels for DDR2-667 and DDR2-800 Symbol Parameter DDR2-667, DDR2-800 Min. Max. Units VIH(dc) VIL(dc) VIH(ac) VIL(ac) DC input logic high DC input low AC input logic high AC input low VREF + 0.125 -0.3 VDDQ + 0.3 VREF - 0.125 -- V V V V VREF + 0.200 -- VREF - 0.200 TABLE 28 DC & AC Logic Input Levels for DDR2-533 and DDR2-400 Symbol Parameter DDR2-533, DDR2-400 Min. Max. Units VIH(dc) VIL(dc) VIH(ac) VIL(ac) DC input logic high DC input low AC input logic high AC input low VREF + 0.125 -0.3 VDDQ + 0.3 VREF - 0.125 -- V V V V VREF + 0.250 -- VREF - 0.250 TABLE 29 Single-ended AC Input Test Conditions Symbol Condition Input reference voltage Input signal maximum peak to peak swing Input signal minimum Slew Rate Value 0.5 x VDDQ 1.0 1.0 Unit V V V / ns Note 1) 1) 2)3) VREF VSWING.MAX SLEW 1) Input waveform timing is referenced to the input signal crossing through the VREF level applied to the device under test. 2) The input signal minimum Slew Rate is to be maintained over the range from VIH(ac).MIN to VREF for rising edges and the range from VREF to VIL(ac).MAX for falling edges as shown in Figure 4 3) AC timings are referenced with input waveforms switching from VIL(ac) to VIH(ac) on the positive transitions and VIH(ac) to VIL(ac) on the negative transitions. Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 29 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM FIGURE 4 Single-ended AC Input Test Conditions Diagram TABLE 30 Differential DC and AC Input and Output Logic Levels Symbol Parameter DC input signal voltage DC differential input voltage AC differential input voltage AC differential cross point input voltage AC differential cross point output voltage Min. -0.3 0.25 0.5 0.5 x VDDQ - 0.175 0.5 x VDDQ - 0.125 Max. Unit -- -- V V V Note 1) 2) 3) 4) 5) VIN(dc) VID(dc) VID(ac) VIX(ac) VOX(ac) 1) 2) 3) 4) VDDQ + 0.3 VDDQ + 0.6 VDDQ + 0.6 0.5 x VDDQ + 0.175 0.5 x VDDQ + 0.125 indicates the voltage at which differential input signals must cross. 5) The value of VOX(ac) is expected to equal 0.5 x VDDQ of the transmitting device and VOX(ac) is expected to track variations in VDDQ. VOX(ac) indicates the voltage at which differential input signals must cross. VIN(dc) specifies the allowable DC execution of each input of differential pair such as CK, CK, DQS, DQS etc. VID(dc) specifies the input differential voltage VTR- VCP required for switching. The minimum value is equal to VIH(dc) - VIL(dc). VID(ac) specifies the input differential voltage VTR - VCP required for switching. The minimum value is equal to VIH(ac) - VIL(ac). The value of VIX(ac) is expected to equal 0.5 x VDDQ of the transmitting device and VIX(ac) is expected to track variations in VDDQ. VIX(ac) Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 30 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM FIGURE 5 Differential DC and AC Input and Output Logic Levels Diagram 5.4 Output Buffer Characteristics TABLE 31 SSTL_18 Output DC Current Drive This chapter describes the Output Buffer Characteristics. Symbol Parameter Output Minimum Source DC Current SSTL_18 -13.4 Unit mA Note 1)2) 2)3) Output Minimum Sink DC Current 13.4 mA 1) VDDQ = 1.7 V; VOUT = 1.42 V. (VOUT-VDDQ) / IOH must be less than 21 Ohm for values of VOUT between VDDQ and VDDQ - 280 mV. 2) The values of IOH(dc) and IOL(dc) are based on the conditions given in 1) and 3). They are used to test drive current capability to ensure VIH.MIN. plus a noise margin and VIL.MAX minus a noise margin are delivered to an SSTL_18 receiver. The actual current values are derived by IOH IOL shifting the desired driver operating points along 21 Ohm load line to define a convenient current for measurement. 3) VDDQ = 1.7 V; VOUT = 280 mV. VOUT / IOL must be less than 21 Ohm for values of VOUT between 0 V and 280 mV. TABLE 32 SSTL_18 Output AC Test Conditions Symbol Parameter Minimum Required Output Pull-up Maximum Required Output Pull-down SSTL_18 Unit V V Note 1) 1) Output Timing Measurement Reference Level V 1) SSTL_18 test load for VOH and VOL is different from the referenced load. The SSTL_18 test load has a 20 Ohm series resistor additionally to the 25 Ohm termination resistor into VTT. The SSTL_18 definition assumes that 335 mV must be developed across the effectively 25 Ohm termination resistor (13.4 mA x 25 Ohm = 335 mV). With an additional series resistor of 20 Ohm this translates into a minimum requirement of 603 mV swing relative to VTT, at the ouput device (13.4 mA x 45 Ohm = 603 mV). VOH VOL VOTR VTT + 0.603 VTT - 0.603 0.5 x VDDQ Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 31 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM TABLE 33 OCD Default Characteristics Symbol -- -- -- Description Output Impedance Pull-up / Pull down mismatch Output Impedance step size for OCD calibration Min. -- 0 0 1.5 -- -- -- 4 1.5 5.0 Nominal Max. Unit V / ns Note 1)2) 1)2)3) 4) Output Slew Rate 1) VDDQ = 1.8 V 0.1 V; VDD = 1.8 V 0.1 V SOUT 1)5)6)7) 2) Impedance measurement condition for output source dc current: VDDQ = 1.7 V, VOUT = 1420 mV; (VOUT-VDDQ) / IOH must be less than 23.4 Ohms for values of VOUT between VDDQ and VDDQ - 280 mV. Impedance measurement condition for output sink dc current: VDDQ = 1.7 V; VOUT = -280 mV; VOUT / IOL must be less than 23.4 Ohms for values of VOUT between 0 V and 280 mV. 3) Mismatch is absolute value between pull-up and pull-down, both measured at same temperature and voltage. 4) This represents the step size when the OCD is near 18 Ohms at nominal conditions across all process parameters and represents only the DRAM uncertainty. A 0 Ohm value (no calibration) can only be achieved if the OCD impedance is 18 0.75 Ohms under nominal conditions. 5) The absolute value of the Slew Rate as measured from DC to DC is equal to or greater than the Slew Rate as measured from AC to AC. This is verified by design and characterization but not subject to production test. 6) Timing skew due to DRAM output Slew Rate mis-match between DQS / DQS and associated DQ's is included in tDQSQ and tQHS specification. 7) DRAM output Slew Rate specification applies to 400, 533 and 667 MT/s speed bins. Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 32 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM 5.5 Input / Output Capacitance TABLE 34 Input / Output Capacitance for DDR2-800 This chapter contains the input / output capacitance. Symbol Parameter DDR2-800 Min. Max. 2.0 0.25 1.75 0.25 3.5 0.5 Unit pF pF pF pF pF pF CCK CDCK CI CDI CIO CDIO Input capacitance, CK and CK Input capacitance delta, CK and CK Input capacitance, all other input-only pins Input capacitance delta, all other input-only pins Input/output capacitance, DQ, DM, DQS, DQS, RDQS, RDQS Input/output capacitance delta, DQ, DM, DQS, DQS, RDQS, RDQS 1.0 -- 1.0 -- 2.5 -- TABLE 35 Input / Output Capacitance for DDR2-667 Symbol Parameter DDR2-667 Min. CCK CDCK CI CDI CIO CDIO Input capacitance, CK and CK Input capacitance delta, CK and CK Input capacitance, all other input-only pins Input capacitance delta, all other input-only pins Input/output capacitance, DQ, DM, DQS, DQS, RDQS, RDQS Input/output capacitance delta, DQ, DM, DQS, DQS, RDQS, RDQS 1.0 -- 1.0 -- 2.5 -- Max. 2.0 0.25 2.0 0.25 3.5 0.5 Unit pF pF pF pF pF pF Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 33 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM TABLE 36 Input / Output Capacitance for DDR2-533 Symbol Parameter DDR2-533 Min. CCK CDCK CI CDI CIO CDIO Input capacitance, CK and CK Input capacitance delta, CK and CK Input capacitance, all other input-only pins Input capacitance delta, all other input-only pins Input/output capacitance, DQ, DM, DQS, DQS, RDQS, RDQS Input/output capacitance delta, DQ, DM, DQS, DQS, RDQS, RDQS 1.0 -- 1.0 -- 2.5 -- Max. 2.0 0.25 2.0 0.25 4.0 0.5 Unit pF pF pF pF pF pF TABLE 37 Input / Output Capacitance for DDR2-400 Symbol Parameter DDR2-400 Min. CCK CDCK CI CDI CIO CDIO Input capacitance, CK and CK Input capacitance delta, CK and CK Input capacitance, all other input-only pins Input capacitance delta, all other input-only pins Input/output capacitance, DQ, DM, DQS, DQS, RDQS, RDQS Input/output capacitance delta, DQ, DM, DQS, DQS, RDQS, RDQS 1.0 -- 1.0 -- 2.5 -- Max. 2.0 0.25 2.0 0.25 4.0 0.5 Unit pF pF pF pF pF pF Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 34 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM 5.6 Overshoot and Undershoot Specification TABLE 38 AC Overshoot / Undershoot Specification for Address and Control Pins This chapter contains overshoot and undershoot specification. Parameter Maximum peak amplitude allowed for overshoot area Maximum peak amplitude allowed for undershoot area Maximum overshoot area above VDD Maximum undershoot area below VSS DDR2-400 0.9 0.9 1.33 1.33 DDR2-533 0.9 0.9 1.00 1.00 DDR2-667 0.9 0.9 0.80 0.80 DDR2-800 0.9 0.9 0.66 0.66 Unit V V V.ns V.ns FIGURE 6 AC Overshoot / Undershoot Diagram for Address and Control Pins TABLE 39 AC Overshoot / Undershoot Spec. for Clock, Data, Strobe and Mask Pins Parameter Maximum peak amplitude allowed for overshoot area Maximum peak amplitude allowed for undershoot area Maximum overshoot area above VDDQ Maximum undershoot area below VSSQ DDR2-400 0.9 0.9 0.38 0.38 DDR2-533 0.9 0.9 0.28 0.28 DDR2-667 0.9 0.9 0.23 0.23 DDR2-800 0.9 0.9 0.23 0.23 Unit V V V.ns V.ns Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 35 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM FIGURE 7 AC Overshoot / Undershoot Diagram for Clock, Data, Strobe and Mask Pins Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 36 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM 6 Currents Measurement Conditions TABLE 40 IDD Measurement Conditions This chapter describes the current measurement specifications and conditions. Parameter Operating Current - One bank Active - Precharge tCK = tCK(IDD), tRC = tRC(IDD), tRAS = tRAS.MIN(IDD), CKE is HIGH, CS is HIGH between valid commands. Address and control inputs are switching; Databus inputs are switching. Symbol Note IDD0 1)2)3)4)5) Operating Current - One bank Active - Read - Precharge IDD1 IOUT = 0 mA, BL = 4, tCK = tCK(IDD), tRC = tRC(IDD), tRAS = tRAS.MIN(IDD), tRCD = tRCD(IDD), AL = 0, CL = CL(IDD); CKE is HIGH, CS is HIGH between valid commands. Address and control inputs are switching; Databus inputs are switching. Precharge Power-Down Current IDD2P All banks idle; CKE is LOW; tCK = tCK(IDD);Other control and address inputs are stable; Data bus inputs are floating. Precharge Standby Current All banks idle; CS is HIGH; CKE is HIGH; tCK = tCK(IDD); Other control and address inputs are switching, Data bus inputs are switching. 1)2)3)4)5) 1)2)3)4)5) IDD2N 1)2)3)4)5) Precharge Quiet Standby Current IDD2Q All banks idle; CS is HIGH; CKE is HIGH; tCK = tCK(IDD); Other control and address inputs are stable, Data bus inputs are floating. Active Power-Down Current IDD3P(0) All banks open; tCK = tCK(IDD), CKE is LOW; Other control and address inputs are stable; Data bus inputs are floating. MRS A12 bit is set to "0" (Fast Power-down Exit). Active Power-Down Current IDD3P(1) All banks open; tCK = tCK(IDD), CKE is LOW; Other control and address inputs are stable, Data bus inputs are floating. MRS A12 bit is set to 1 (Slow Power-down Exit); Active Standby Current All banks open; tCK = tCK(IDD); tRAS = tRAS.MAX(IDD), tRP = tRP(IDD); CKE is HIGH, CS is HIGH between valid commands. Address inputs are switching; Data Bus inputs are switching; Operating Current Burst Read: All banks open; Continuous burst reads; BL = 4; AL = 0, CL = CL(IDD); tCK = tCK(IDD); tRAS = tRAS.MAX.(IDD), tRP = tRP(IDD); CKE is HIGH, CS is HIGH between valid commands. Address inputs are switching; Data Bus inputs are switching; IOUT = 0 mA. Operating Current Burst Write: All banks open; Continuous burst writes; BL = 4; AL = 0, CL = CL(IDD); tCK = tCK(IDD); tRAS = tRAS.MAX(IDD), tRP = tRP(IDD); CKE is HIGH, CS is HIGH between valid commands. Address inputs are switching; Data Bus inputs are switching; Burst Refresh Current tCK = tCK(IDD), Refresh command every tRFC = tRFC(IDD) interval, CKE is HIGH, CS is HIGH between valid commands, Other control and address inputs are switching, Data bus inputs are switching. 1)2)3)4)5) 1)2)3)4)5) 1)2)3)4)5) IDD3N 1)2)3)4)5) IDD4R 1)2)3)4)5) IDD4W 1)2)3)4)5) IDD5B 1)2)3)4)5) Distributed Refresh Current IDD5D tCK = tCK(IDD), Refresh command every tREFI = 7.8 s interval, CKE is LOW and CS is HIGH between valid commands, Other control and address inputs are switching, Data bus inputs are switching. 1)2)3)4)5) Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 37 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM Parameter Self-Refresh Current CKE 0.2 V; external clock off, CK and CK at 0 V; Other control and address inputs are floating, Data bus inputs are floating. Symbol Note IDD6 1)2)3)4)5) Operating Bank Interleave Read Current IDD7 1. All banks interleaving reads, IOUT = 0 mA; BL = 4, CL = CL(IDD), AL = tRCD(IDD) -1 x tCK(IDD); tCK = tCK(IDD), tRC = tRC(IDD), tRRD = tRRD(IDD); CKE is HIGH, CS is HIGH between valid commands. Address bus inputs are stable during deselects; Data bus is switching. 2. Timing pattern: DDR2-400-333: A0 RA0 A1 RA1 A2 RA2 A3 RA3 D D D (11 clocks) 1)2)3)4)5)6) DDR2-667-444: A0 RA0 D D A1 RA1 D D A2 RA2 D D A3 RA3 D D D D D (19 clocks) DDR2-667-555: A0 RA0 D D A1 RA1 D D A2 RA2 D D A3 RA3 D D D D D D (20 clocks) DDR2-800-555: A0 RA0 D D D A1 RA1 D D D A2 RA2 D D D A3 RA3 D D D D D(22 clocks) DDR2-800-666: A0 RA0 D D D A1 RA1 D D D A2 RA2 D D D A3 RA3 D D D D D D(23 clocks) 1) VDDQ = 1.8 V 0.1 V; VDD = 1.8 V 0.1 V 2) IDD specifications are tested after the device is properly initialized. 3) IDD parameter are specified with ODT disabled. 4) Data Bus consists of DQ, DM, DQS, DQS, RDQS, RDQS, LDQS, LDQS, UDQS and UDQS. 5) Definitions for IDD: see Table 41 6) A = Activate, RA = Read with Auto-Precharge, D=DESELECT TABLE 41 Definition for IDD Parameter LOW HIGH STABLE FLOATING SWITCHING Description defined as VIN VIL(ac).MAX defined as VIN VIH(ac).MIN defined as inputs are stable at a HIGH or LOW level defined as inputs are VREF = VDDQ / 2 defined as: Inputs are changing between high and low every other clock (once per two clocks) for address and control signals, and inputs changing between high and low every other clock (once per clock) for DQ signals not including mask or strobes Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 38 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM TABLE 42 IDDSpecification -25F DDR2-800D Symbol IDD0 IDD1 IDD2P IDD2N IDD2Q IDD3P IDD3N IDD4R IDD4W IDD5B IDD5D IDD6 IDD7 Max. 84 105 100 120 7 51 45 39 9 60 155 180 155 200 145 9 7 170 265 1) MRS(12)=0 2) MRS(12)=1 3) 0 TCASE 85C. -2.5 DDR2-800E Max. 80 100 95 115 7 51 45 39 9 60 155 180 155 200 145 9 7 160 255 -3 DDR2-667C Max. 75 95 90 105 7 45 40 33 9 50 130 155 130 170 140 9 7 160 252 -3S DDR2-667D Max. 71 90 85 100 7 45 40 33 9 50 130 155 130 170 140 9 7 152 240 -3.7 DDR2-533C Max. 65 80 75 90 7 38 35 28 9 43 110 130 110 145 130 9 7 145 230 -5 DDR2-400B Max. 61 75 70 83 7 34 32 24 9 39 95 115 95 130 125 9 7 141 220 Unit Note mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA x4/x8 x16 x4/x8 x16 1) 2) x4/x8 x16 x4/x8 x16 3) 3) x4/x8 x16 Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 39 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM 7 7.1 Timing Characteristics Speed Grade Definitions TABLE 43 Speed Grade Definition Speed Bins for DDR2-800 This chapter contains speed grade definition, AC timing parameter and ODT tables. All Speed grades faster than DDR2-400B comply with DDR2-400B timing specifications (tCK = 5ns with tRAS = 40ns). Speed Grade QAG Sort Name CAS-RCD-RP latencies Parameter Clock Frequency @ CL = 3 @ CL = 4 @ CL = 5 @ CL = 6 Row Active Time Row Cycle Time RAS-CAS-Delay Row Precharge Time Symbol DDR2-800D -25F 5-5-5 Min. 5 3.75 2.5 2.5 45 57.5 12.5 12.5 Max. 8 8 8 8 70000 -- -- -- DDR2-800E -2.5 6-6-6 Min. 5 3.75 3 2.5 45 60 15 15 Max. 8 8 8 8 70000 -- -- -- Unit Note tCK -- ns ns ns ns ns ns ns ns 1)2)3)4) 1)2)3)4) 1)2)3)4) 1)2)3)4) 1)2)3)4)5) 1)2)3)4) 1)2)3)4) 1)2)3)4) tCK tCK tCK tCK tRAS tRC tRCD tRP 1) Timings are guaranteed with CK/CK differential Slew Rate of 2.0 V/ns. For DQS signals timings are guaranteed with a differential Slew Rate of 2.0 V/ns in differential strobe mode and a Slew Rate of 1 V/ns in single ended mode. Timings are further guaranteed for normal OCD drive strength (EMRS(1) A1 = 0) under the "Reference Load for Timing Measurements". 2) The CK/CK input reference level (for timing reference to CK/CK) is the point at which CK and CK cross. The DQS / DQS, RDQS / RDQS, input reference level is the crosspoint when in differential strobe mode; The input reference level for signals other than CK/CK, DQS / DQS, RDQS / RDQS is defined . 3) Inputs are not recognized as valid until VREF stabilizes. During the period before VREF stabilizes, CKE = 0.2 x VDDQ is recognized as low. 4) The output timing reference voltage level is VTT. 5) tRAS.MAX is calculated from the maximum amount of time a DDR2 device can operate without a refresh command which is equal to 9 x tREFI. Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 40 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM TABLE 44 Speed Grade Definition Speed Bins for DDR2-667 Speed Grade QAG Sort Name CAS-RCD-RP latencies Parameter Clock Frequency @ CL = 3 @ CL = 4 @ CL = 5 Row Active Time Row Cycle Time RAS-CAS-Delay Row Precharge Time Symbol DDR2-667C -3 4-4-4 Min. 5 3 3 45 57 12 12 Max. 8 8 8 70000 -- -- -- DDR2-667D -3S 5-5-5 Min. 5 3.75 3 45 60 15 15 Max. 8 8 8 70000 -- -- -- Unit Note tCK -- ns ns ns ns ns ns ns 1)2)3)4) 1)2)3)4) 1)2)3)4) 1)2)3)4)5) 1)2)3)4) 1)2)3)4) 1)2)3)4) tCK tCK tCK tRAS tRC tRCD tRP 1) imings are guaranteed with CK/CK differential Slew Rate of 2.0 V/ns. For DQS signals timings are guaranteed with a differential Slew Rate of 2.0 V/ns in differential strobe mode and a Slew Rate of 1 V/ns in single ended mode. Timings are further guaranteed for normal OCD drive strength (EMRS(1) A1 = 0) under the "Reference Load for Timing Measurements". 2) The CK/CK input reference level (for timing reference to CK/CK) is the point at which CK and CK cross. The DQS / DQS, RDQS / RDQS, input reference level is the crosspoint when in differential strobe mode; The input reference level for signals other than CK/CK, DQS / DQS, RDQS / RDQS is defined. 3) Inputs are not recognized as valid until VREF stabilizes. During the period before VREF stabilizes, CKE = 0.2 x VDDQ is recognized as low. 4) The output timing reference voltage level is VTT. 5) tRAS.MAX is calculated from the maximum amount of time a DDR2 device can operate without a refresh command which is equal to 9 x tREFI. TABLE 45 Speed Grade Definition Speed Bins for DDR2-533 Speed Grade QAG Sort Name CAS-RCD-RP latencies Parameter Clock Frequency @ CL = 3 @ CL = 4 @ CL = 5 Row Active Time Row Cycle Time RAS-CAS-Delay Row Precharge Time Symbol DDR2-533C -3.7 4-4-4 Min. 5 3.75 3.75 45 60 15 15 Max. 8 8 8 70000 -- -- -- DDR2-533B -37F 3-3-3 Min. 3.75 3.75 3.75 45 56.25 11.25 11.25 Max. 8 8 8 70000 -- -- -- Unit Note tCK -- ns ns ns ns ns ns ns 1)2)3)4) 1)2)3)4) 1)2)3)4) 1)2)3)4)5) 1)2)3)4) 1)2)3)4) 1)2)3)4) tCK tCK tCK tRAS tRC tRCD tRP 1) Timings are guaranteed with CK/CK differential Slew Rate of 2.0 V/ns. For DQS signals timings are guaranteed with a differential Slew Rate of 2.0 V/ns in differential strobe mode and a Slew Rate of 1 V/ns in single ended mode. Timings are further guaranteed for normal OCD drive strength (EMRS(1) A1 = 0) under the "Reference Load for Timing Measurements". 2) The CK/CK input reference level (for timing reference to CK/CK) is the point at which CK and CK cross. The DQS / DQS, RDQS / RDQS, input reference level is the crosspoint when in differential strobe mode; The input reference level for signals other than CK/CK, DQS / DQS, RDQS / RDQS is defined. Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 41 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM 3) Inputs are not recognized as valid until VREF stabilizes. During the period before VREF stabilizes, CKE = 0.2 x VDDQ is recognized as low. 4) The output timing reference voltage level is VTT. 5) tRAS.MAX is calculated from the maximum amount of time a DDR2 device can operate without a refresh command which is equal to 9 x tREFI. TABLE 46 Speed Grade Definition Speed Bins for DDR2-400B Speed Grade QAG Sort Name CAS-RCD-RP latencies Parameter Clock Frequency @ CL = 3 @ CL = 4 @ CL = 5 Row Active Time Row Cycle Time RAS-CAS-Delay Row Precharge Time Symbol DDR2-400B -5 3-3-3 Min. 5 5 5 40 55 15 15 Max. 8 8 8 70000 -- -- -- Unit Note tCK -- ns ns ns ns ns ns ns 1)2)3)4) 1)2)3)4) 1)2)3)4) 1)2)3)4)5) 1)2)3)4) 1)2)3)4) 1)2)3)4) tCK tCK tCK tRAS tRC tRCD tRP 1) Timings are guaranteed with CK/CK differential Slew Rate of 2.0 V/ns. For DQS signals timings are guaranteed with a differential Slew Rate of 2.0 V/ns in differential strobe mode and a Slew Rate of 1 V/ns in single ended mode. Timings are further guaranteed for normal OCD drive strength (EMRS(1) A1 = 0). 2) The CK/CK input reference level (for timing reference to CK/CK) is the point at which CK and CK cross. The DQS / DQS, RDQS / RDQS, input reference level is the crosspoint when in differential strobe mode. 3) Inputs are not recognized as valid until VREF stabilizes. During the period before VREF stabilizes, CKE = 0.2 x VDDQ is recognized as low. 4) The output timing reference voltage level is VTT. See section 8 for the reference load for timing measurements. 5) tRAS.MAX is calculated from the maximum amount of time a DDR2 device can operate without a refresh command which is equal to 9 x tREFI. Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 42 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM 7.2 Component AC Timing Parameters TABLE 47 DRAM Component Timing Parameter by Speed Grade - DDR2-800 List of Timing Parameters Tables. Parameter Symbol DDR2-800 Min. Max. +400 -- 0.52 8000 -- 0.52 -- -- -- -- +350 -- -- 200 +0.25 -- -- -- -- Unit Note 1)2)3)4)5)6)7) DQ output access time from CK / CK CAS to CAS command delay Average clock high pulse width Average clock period CKE minimum pulse width ( high and low pulse width) Average clock low pulse width tAC tCCD tCH.AVG tCK.AVG tCKE -400 2 0.48 2500 3 0.48 WR + tnRP ps 8) nCK tCK.AVG ps 9)10) 9)10) 11) nCK tCK.AVG nCK ns ps tCL.AVG Auto-Precharge write recovery + precharge time tDAL Minimum time clocks remain ON after CKE tDELAY asynchronously drops LOW DQ and DM input hold time 9)10) 12)13) tIS + tCK .AVG + tIH 125 0.35 -350 0.35 0.35 -- -0.25 50 0.2 0.2 Min(tCH.ABS, tCL.ABS) -- 250 0.6 175 2 x tAC.MIN tDH.BASE DQ and DM input pulse width for each input tDIPW DQS output access time from CK / CK tDQSCK DQS input high pulse width tDQSH DQS input low pulse width tDQSL DQS-DQ skew for DQS & associated DQ signals tDQSQ DQS latching rising transition to associated clock tDQSS edges DQ and DM input setup time DQS falling edge hold time from CK DQS falling edge to CK setup time CK half pulse width Data-out high-impedance time from CK / CK 18)19)14) tCK.AVG ps 8) tCK.AVG tCK.AVG ps 15) 16) tCK.AVG ps tDS.BASE tDSH tDSS tHP 17)18)19) 16) 16) 20) tCK.AVG tCK.AVG ps ps ps tHZ Address and control input hold time tIH.BASE Control & address input pulse width for each input tIPW Address and control input setup time tIS.BASE DQ low impedance time from CK/CK tLZ.DQ DQS/DQS low-impedance time from CK / CK tLZ.DQS MRS command to ODT update delay tMOD Mode register set command cycle time tMRD OCD drive mode output delay tOIT DQ/DQS output hold time from DQS tQH DQ hold skew factor tQHS tAC.MAX -- -- -- tAC.MAX 8)21) 22)24) tCK.AVG ps ps ps ns 23)24) 8)21) 8)21) 34) tAC.MIN 0 2 0 tAC.MAX 12 -- 12 -- 300 nCK ns ps ps 34) 25) 26) tHP - tQHS -- Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 43 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM Parameter Symbol DDR2-800 Min. Max. 7.8 3.9 -- -- -- 1.1 0.6 -- -- 0.6 -- -- -- -- -- -- -- Unit Note 1)2)3)4)5)6)7) Average periodic refresh Interval Auto-Refresh to Active/Auto-Refresh command period Precharge-All (4 banks) command period Precharge-All (8 banks) command period Read preamble Read postamble Internal Read to Precharge command delay Write preamble Write postamble Write recovery time Internal write to read command delay Exit power down to read command Exit active power-down mode to read command (slow exit, lower power) Exit precharge power-down to any valid command (other than NOP or Deselect) Exit self-refresh to a non-read command Exit self-refresh to read command Write command to DQS associated clock edges 1) VDDQ = 1.8 V 0.1V; VDD = 1.8 V 0.1 V. tREFI tRFC tRP tRP tRPRE tRPST tRTP tWPRE tWPST tWR tWTR tXARD tXARDS tXP tXSNR tXSRD WL -- -- 105 s s ns ns ns 27)28) 28)29) 30) tRP tRP + 1 x tCK 0.9 0.4 7.5 0.35 0.4 15 7.5 2 8 - AL 2 tCK.AVG tCK.AVG ns 31)32) 31)33) 34) tCK.AVG tCK.AVG ns ns 34) 34)35) nCK nCK nCK ns 34) tRFC +10 200 RL - 1 nCK nCK 2) Timing that is not specified is illegal and after such an event, in order to guarantee proper operation, the DRAM must be powered down and then restarted through the specified initialization sequence before normal operation can continue. 3) Timings are guaranteed with CK/CK differential Slew Rate of 2.0 V/ns. For DQS signals timings are guaranteed with a differential Slew Rate of 2.0 V/ns in differential strobe mode and a Slew Rate of 1 V/ns in single ended mode. 4) The CK / CK input reference level (for timing reference to CK / CK) is the point at which CK and CK cross. The DQS / DQS, RDQS / RDQS, input reference level is the crosspoint when in differential strobe mode. 5) Inputs are not recognized as valid until VREF stabilizes. During the period before VREF stabilizes, CKE = 0.2 x VDDQ is recognized as low. 6) The output timing reference voltage level is VTT. 7) New units, `tCK.AVG` and `nCK`, are introduced in DDR2-667 and DDR2-800. Unit `tCK.AVG` represents the actual tCK.AVG of the input clock under operation. Unit `nCK` represents one clock cycle of the input clock, counting the actual clock edges. Note that in DDR2-400 and DDR2-533, `tCK` is used for both concepts. Example: tXP = 2 [nCK] means; if Power Down exit is registered at Tm, an Active command may be registered at Tm + 2, even if (Tm + 2 - Tm) is 2 x tCK.AVG + tERR.2PER(Min). 8) When the device is operated with input clock jitter, this parameter needs to be derated by the actual tERR(6-10per) of the input clock. (output deratings are relative to the SDRAM input clock.) For example, if the measured jitter into a DDR2-667 SDRAM has tERR(6-10PER).MIN = - 272 ps and tERR(6- 10PER).MAX = + 293 ps, then tDQSCK.MIN(DERATED) = tDQSCK.MIN - tERR(6-10PER).MAX = - 400 ps - 293 ps = - 693 ps and tDQSCK.MAX(DERATED) = tDQSCK.MAX - tERR(6-10PER).MIN = 400 ps + 272 ps = + 672 ps. Similarly, tLZ.DQ for DDR2-667 derates to tLZ.DQ.MIN(DERATED) = - 900 ps - 293 ps = - 1193 ps and tLZ.DQ.MAX(DERATED) = 450 ps + 272 ps = + 722 ps. (Caution on the MIN/MAX usage!) 9) Input clock jitter spec parameter. These parameters and the ones in Chapter 7.3 are referred to as 'input clock jitter spec parameters' and these parameters apply to DDR2-667 and DDR2-800 only. The jitter specified is a random jitter meeting a Gaussian distribution. 10) These parameters are specified per their average values, however it is understood that the relationship as defined in Chapter 7.3 between the average timing and the absolute instantaneous timing holds all the times (min. and max of SPEC values are to be used for calculations of Chapter 7.3). 11) tCKE.MIN of 3 clocks means CKE must be registered on three consecutive positive clock edges. CKE must remain at the valid input level the entire time it takes to achieve the 3 clocks of registration. Thus, after any CKE transition, CKE may not transition from its valid level during the time period of tIS + 2 x tCK + tIH. Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 44 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM 12) DAL = WR + RU{tRP(ns) / tCK(ns)}, where RU stands for round up. WR refers to the tWR parameter stored in the MRS. For tRP, if the result of the division is not already an integer, round up to the next highest integer. tCK refers to the application clock period. Example: For DDR2-533 at tCK = 3.75 ns with tWR programmed to 4 clocks. tDAL = 4 + (15 ns / 3.75 ns) clocks = 4 + (4) clocks = 8 clocks. 13) tDAL.nCK = WR [nCK] + tnRP.nCK = WR + RU{tRP [ps] / tCK.AVG[ps] }, where WR is the value programmed in the EMR. 14) Input waveform timing tDH with differential data strobe enabled MR[bit10] = 0, is referenced from the differential data strobe crosspoint to the input signal crossing at the VIH.DC level for a falling signal and from the differential data strobe crosspoint to the input signal crossing at the VIL.DC level for a rising signal applied to the device under test. DQS, DQS signals must be monotonic between VIL.DC.MAX and VIH.DC.MIN. See Figure 9. 15) tDQSQ: Consists of data pin skew and output pattern effects, and p-channel to n-channel variation of the output drivers as well as output slew rate mismatch between DQS / DQS and associated DQ in any given cycle. 16) These parameters are measured from a data strobe signal ((L/U/R)DQS / DQS) crossing to its respective clock signal (CK / CK) crossing. The spec values are not affected by the amount of clock jitter applied (i.e. tJIT.PER, tJIT.CC, etc.), as these are relative to the clock signal crossing. That is, these parameters should be met whether clock jitter is present or not. 17) Input waveform timing tDS with differential data strobe enabled MR[bit10] = 0, is referenced from the input signal crossing at the VIH.AC level to the differential data strobe crosspoint for a rising signal, and from the input signal crossing at the VIL.AC level to the differential data strobe crosspoint for a falling signal applied to the device under test. DQS, DQS signals must be monotonic between Vil(DC)MAX and Vih(DC)MIN. See Figure 9. 18) If tDS or tDH is violated, data corruption may occur and the data must be re-written with valid data before a valid READ can be executed. 19) These parameters are measured from a data signal ((L/U)DM, (L/U)DQ0, (L/U)DQ1, etc.) transition edge to its respective data strobe signal ((L/U/R)DQS / DQS) crossing. 20) tHP is the minimum of the absolute half period of the actual input clock. tHP is an input parameter but not an input specification parameter. It is used in conjunction with tQHS to derive the DRAM output timing tQH. The value to be used for tQH calculation is determined by the following equation; tHP = MIN (tCH.ABS, tCL.ABS), where, tCH.ABS is the minimum of the actual instantaneous clock high time; tCL.ABS is the minimum of the actual instantaneous clock low time. 21) tHZ and tLZ transitions occur in the same access time as valid data transitions. These parameters are referenced to a specific voltage level which specifies when the device output is no longer driving (tHZ), or begins driving (tLZ) . 22) Input waveform timing is referenced from the input signal crossing at the VIL.DC level for a rising signal and VIH.DC for a falling signal applied to the device under test. See Figure 10. 23) Input waveform timing is referenced from the input signal crossing at the VIH.AC level for a rising signal and VIL.AC for a falling signal applied to the device under test. See Figure 10. 24) These parameters are measured from a command/address signal (CKE, CS, RAS, CAS, WE, ODT, BA0, A0, A1, etc.) transition edge to its respective clock signal (CK / CK) crossing. The spec values are not affected by the amount of clock jitter applied (i.e. tJIT.PER, tJIT.CC, etc.), as the setup and hold are relative to the clock signal crossing that latches the command/address. That is, these parameters should be met whether clock jitter is present or not. 25) tQH = tHP - tQHS, where: tHP is the minimum of the absolute half period of the actual input clock; and tQHS is the specification value under the max column. {The less half-pulse width distortion present, the larger the tQH value is; and the larger the valid data eye will be.} Examples: 1) If the system provides tHP of 1315 ps into a DDR2-667 SDRAM, the DRAM provides tQH of 975 ps minimum. 2) If the system provides tHP of 1420 ps into a DDR2-667 SDRAM, the DRAM provides tQH of 1080 ps minimum. 26) tQHS accounts for: 1) The pulse duration distortion of on-chip clock circuits, which represents how well the actual tHP at the input is transferred to the output; and 2) The worst case push-out of DQS on one transition followed by the worst case pull-in of DQ on the next transition, both of which are independent of each other, due to data pin skew, output pattern effects, and pchannel to n-channel variation of the output drivers. 27) The Auto-Refresh command interval has be reduced to 3.9 s when operating the DDR2 DRAM in a temperature range between 85 C and 95 C. 28) 0 C TCASE 85 C 29) 85 C < TCASE 95 C 30) A maximum of eight Auto-Refresh commands can be posted to any given DDR2 SDRAM device. 31) tRPST end point and tRPRE begin point are not referenced to a specific voltage level but specify when the device output is no longer driving (tRPST), or begins driving (tRPRE). Figure 8 shows a method to calculate these points when the device is no longer driving (tRPST), or begins driving (tRPRE) by measuring the signal at two different voltages. The actual voltage measurement points are not critical as long as the calculation is consistent. 32) When the device is operated with input clock jitter, this parameter needs to be derated by the actual tJIT.PER of the input clock. (output deratings are relative to the SDRAM input clock.) For example, if the measured jitter into a DDR2-667 SDRAM has tJIT.PER.MIN = - 72 ps and tJIT.PER.MAX = + 93 ps, then tRPRE.MIN(DERATED) = tRPRE.MIN + tJIT.PER.MIN = 0.9 x tCK.AVG - 72 ps = + 2178 ps and tRPRE.MAX(DERATED) = tRPRE.MAX + tJIT.PER.MAX = 1.1 x tCK.AVG + 93 ps = + 2843 ps. (Caution on the MIN/MAX usage!). Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 45 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM 33) When the device is operated with input clock jitter, this parameter needs to be derated by the actual tJIT.DUTY of the input clock. (output deratings are relative to the SDRAM input clock.) For example, if the measured jitter into a DDR2-667 SDRAM has tJIT.DUTY.MIN = - 72 ps and tJIT.DUTY.MAX = + 93 ps, then tRPST.MIN(DERATED) = tRPST.MIN + tJIT.DUTY.MIN = 0.4 x tCK.AVG - 72 ps = + 928 ps and tRPST.MAX(DERATED) = tRPST.MAX + tJIT.DUTY.MAX = 0.6 x tCK.AVG + 93 ps = + 1592 ps. (Caution on the MIN/MAX usage!). 34) For these parameters, the DDR2 SDRAM device is characterized and verified to support tnPARAM = RU{tPARAM / tCK.AVG}, which is in clock cycles, assuming all input clock jitter specifications are satisfied. For example, the device will support tnRP = RU{tRP / tCK.AVG}, which is in clock cycles, if all input clock jitter specifications are met. This means: For DDR2-667 5-5-5, of which tRP = 15 ns, the device will support tnRP = RU{tRP / tCK.AVG} = 5, i.e. as long as the input clock jitter specifications are met, Precharge command at Tm and Active command at Tm + 5 is valid even if (Tm + 5 - Tm) is less than 15 ns due to input clock jitter. 35) tWTR is at lease two clocks (2 x tCK) independent of operation frequency. TABLE 48 DRAM Component Timing Parameter by Speed Grade - DDR2-667 Parameter Symbol DDR2-667 Min. DQ output access time from CK / CK CAS to CAS command delay Average clock high pulse width Average clock period CKE minimum pulse width ( high and low pulse width) Average clock low pulse width Max. +450 -- 0.52 8000 -- 0.52 -- -- -- -- +400 -- -- 240 +0.25 -- -- -- -- ps 8) Unit Note 1)2)3)4)5)6)7) tAC tCCD tCH.AVG tCK.AVG tCKE -450 2 0.48 3000 3 0.48 WR + tnRP nCK tCK.AVG ps 9)10) nCK tCK.AVG nCK ns ps 11) tCL.AVG Auto-Precharge write recovery + precharge time tDAL Minimum time clocks remain ON after CKE tDELAY asynchronously drops LOW DQ and DM input hold time 9)10) 12)13) tIS + tCK .AVG + tIH 175 0.35 -400 0.35 0.35 -- -0.25 100 0.2 0.2 Min(tCH.ABS, tCL.ABS) -- 275 0.6 200 2 x tAC.MIN tDH.BASE DQ and DM input pulse width for each input tDIPW DQS output access time from CK / CK tDQSCK DQS input high pulse width tDQSH DQS input low pulse width tDQSL DQS-DQ skew for DQS & associated DQ signals tDQSQ DQS latching rising transition to associated clock tDQSS edges DQ and DM input setup time DQS falling edge hold time from CK DQS falling edge to CK setup time CK half pulse width Data-out high-impedance time from CK / CK 18)19)14) tCK.AVG ps 8) tCK.AVG tCK.AVG ps 15) 16) tCK.AVG ps tDS.BASE tDSH tDSS tHP 17)18)19) 16) 16) 20) tCK.AVG tCK.AVG ps ps ps tHZ Address and control input hold time tIH.BASE Control & address input pulse width for each input tIPW Address and control input setup time tIS.BASE DQ low impedance time from CK/CK tLZ.DQ DQS/DQS low-impedance time from CK / CK tLZ.DQS MRS command to ODT update delay tMOD tAC.MAX -- -- -- 8)21) 24)22) tCK.AVG ps ps ps ns 23)24) 8)21) 8)21) 34) tAC.MIN 0 tAC.MAX tAC.MAX 12 Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 46 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM Parameter Symbol DDR2-667 Min. Max. -- 12 -- 340 7.8 3.9 -- -- 1.1 0.6 -- -- 0.6 -- -- -- -- -- -- -- Unit Note 1)2)3)4)5)6)7) Mode register set command cycle time OCD drive mode output delay DQ/DQS output hold time from DQS DQ hold skew factor Average periodic refresh Interval Auto-Refresh to Active/Auto-Refresh command period Precharge-All (4 banks) command period Read preamble Read postamble Internal Read to Precharge command delay Write preamble Write postamble Write recovery time Internal write to read command delay Exit power down to read command Exit active power-down mode to read command (slow exit, lower power) Exit precharge power-down to any valid command (other than NOP or Deselect) Exit self-refresh to a non-read command Exit self-refresh to read command Write command to DQS associated clock edges 1) VDDQ = 1.8 V 0.1V; VDD = 1.8 V 0.1 V. tMRD tOIT tQH tQHS tREFI tRFC tRP tRPRE tRPST tRTP tWPRE tWPST tWR tWTR tXARD tXARDS tXP tXSNR tXSRD WL 2 0 nCK ns ps ps s s ns ns 34) 25) 26) 27)28) 28)29) 30) tHP - tQHS -- -- -- 105 tRP 0.9 0.4 7.5 0.35 0.4 15 7.5 2 7 - AL 2 tCK.AVG tCK.AVG ns 31)32) 31)33) 34) tCK.AVG tCK.AVG ns ns 34) 34)35) nCK nCK nCK ns 34) tRFC +10 200 RL-1 nCK nCK 2) Timing that is not specified is illegal and after such an event, in order to guarantee proper operation, the DRAM must be powered down and then restarted through the specified initialization sequence before normal operation can continue. 3) Timings are guaranteed with CK/CK differential Slew Rate of 2.0 V/ns. For DQS signals timings are guaranteed with a differential Slew Rate of 2.0 V/ns in differential strobe mode and a Slew Rate of 1 V/ns in single ended mode. 4) The CK / CK input reference level (for timing reference to CK / CK) is the point at which CK and CK cross. The DQS / DQS, RDQS / RDQS, input reference level is the crosspoint when in differential strobe mode. 5) Inputs are not recognized as valid until VREF stabilizes. During the period before VREF stabilizes, CKE = 0.2 x VDDQ is recognized as low. 6) The output timing reference voltage level is VTT. 7) New units, `tCK.AVG` and `nCK`, are introduced in DDR2-667 and DDR2-800. Unit `tCK.AVG` represents the actual tCK.AVG of the input clock under operation. Unit `nCK` represents one clock cycle of the input clock, counting the actual clock edges. Note that in DDR2-400 and DDR2-533, `tCK` is used for both concepts. Example: tXP = 2 [nCK] means; if Power Down exit is registered at Tm, an Active command may be registered at Tm + 2, even if (Tm + 2 - Tm) is 2 x tCK.AVG + tERR.2PER(Min). 8) When the device is operated with input clock jitter, this parameter needs to be derated by the actual tERR(6-10per) of the input clock. (output deratings are relative to the SDRAM input clock.) For example, if the measured jitter into a DDR2-667 SDRAM has tERR(6-10PER).MIN = - 272 ps and tERR(6- 10PER).MAX = + 293 ps, then tDQSCK.MIN(DERATED) = tDQSCK.MIN - tERR(6-10PER).MAX = - 400 ps - 293 ps = - 693 ps and tDQSCK.MAX(DERATED) = tDQSCK.MAX - tERR(6-10PER).MIN = 400 ps + 272 ps = + 672 ps. Similarly, tLZ.DQ for DDR2-667 derates to tLZ.DQ.MIN(DERATED) = - 900 ps - 293 ps = - 1193 ps and tLZ.DQ.MAX(DERATED) = 450 ps + 272 ps = + 722 ps. (Caution on the MIN/MAX usage!) 9) Input clock jitter spec parameter. These parameters and the ones in Chapter 7.3 are referred to as 'input clock jitter spec parameters' and these parameters apply to DDR2-667 and DDR2-800 only. The jitter specified is a random jitter meeting a Gaussian distribution. Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 47 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM 10) These parameters are specified per their average values, however it is understood that the relationship as defined in Chapter 7.3 between the average timing and the absolute instantaneous timing holds all the times (min. and max of SPEC values are to be used for calculations of Chapter 7.3). 11) tCKE.MIN of 3 clocks means CKE must be registered on three consecutive positive clock edges. CKE must remain at the valid input level the entire time it takes to achieve the 3 clocks of registration. Thus, after any CKE transition, CKE may not transition from its valid level during the time period of tIS + 2 x tCK + tIH. 12) DAL = WR + RU{tRP(ns) / tCK(ns)}, where RU stands for round up. WR refers to the tWR parameter stored in the MRS. For tRP, if the result of the division is not already an integer, round up to the next highest integer. tCK refers to the application clock period. Example: For DDR2-533 at tCK = 3.75 ns with tWR programmed to 4 clocks. tDAL = 4 + (15 ns / 3.75 ns) clocks = 4 + (4) clocks = 8 clocks. 13) tDAL.nCK = WR [nCK] + tnRP.nCK = WR + RU{tRP [ps] / tCK.AVG[ps] }, where WR is the value programmed in the EMR. 14) Input waveform timing tDH with differential data strobe enabled MR[bit10] = 0, is referenced from the differential data strobe crosspoint to the input signal crossing at the VIH.DC level for a falling signal and from the differential data strobe crosspoint to the input signal crossing at the VIL.DC level for a rising signal applied to the device under test. DQS, DQS signals must be monotonic between VIL.DC.MAX and VIH.DC.MIN. See Figure 9. 15) tDQSQ: Consists of data pin skew and output pattern effects, and p-channel to n-channel variation of the output drivers as well as output slew rate mismatch between DQS / DQS and associated DQ in any given cycle. 16) These parameters are measured from a data strobe signal ((L/U/R)DQS / DQS) crossing to its respective clock signal (CK / CK) crossing. The spec values are not affected by the amount of clock jitter applied (i.e. tJIT.PER, tJIT.CC, etc.), as these are relative to the clock signal crossing. That is, these parameters should be met whether clock jitter is present or not. 17) Input waveform timing tDS with differential data strobe enabled MR[bit10] = 0, is referenced from the input signal crossing at the VIH.AC level to the differential data strobe crosspoint for a rising signal, and from the input signal crossing at the VIL.AC level to the differential data strobe crosspoint for a falling signal applied to the device under test. DQS, DQS signals must be monotonic between Vil(DC)MAX and Vih(DC)MIN. See Figure 9. 18) If tDS or tDH is violated, data corruption may occur and the data must be re-written with valid data before a valid READ can be executed. 19) These parameters are measured from a data signal ((L/U)DM, (L/U)DQ0, (L/U)DQ1, etc.) transition edge to its respective data strobe signal ((L/U/R)DQS / DQS) crossing. 20) tHP is the minimum of the absolute half period of the actual input clock. tHP is an input parameter but not an input specification parameter. It is used in conjunction with tQHS to derive the DRAM output timing tQH. The value to be used for tQH calculation is determined by the following equation; tHP = MIN (tCH.ABS, tCL.ABS), where, tCH.ABS is the minimum of the actual instantaneous clock high time; tCL.ABS is the minimum of the actual instantaneous clock low time. 21) tHZ and tLZ transitions occur in the same access time as valid data transitions. These parameters are referenced to a specific voltage level which specifies when the device output is no longer driving (tHZ), or begins driving (tLZ) . 22) Input waveform timing is referenced from the input signal crossing at the VIL.DC level for a rising signal and VIH.DC for a falling signal applied to the device under test. See Figure 10. 23) Input waveform timing is referenced from the input signal crossing at the VIH.AC level for a rising signal and VIL.AC for a falling signal applied to the device under test. See Figure 10. 24) These parameters are measured from a command/address signal (CKE, CS, RAS, CAS, WE, ODT, BA0, A0, A1, etc.) transition edge to its respective clock signal (CK / CK) crossing. The spec values are not affected by the amount of clock jitter applied (i.e. tJIT.PER, tJIT.CC, etc.), as the setup and hold are relative to the clock signal crossing that latches the command/address. That is, these parameters should be met whether clock jitter is present or not. 25) tQH = tHP - tQHS, where: tHP is the minimum of the absolute half period of the actual input clock; and tQHS is the specification value under the max column. {The less half-pulse width distortion present, the larger the tQH value is; and the larger the valid data eye will be.} Examples: 1) If the system provides tHP of 1315 ps into a DDR2-667 SDRAM, the DRAM provides tQH of 975 ps minimum. 2) If the system provides tHP of 1420 ps into a DDR2-667 SDRAM, the DRAM provides tQH of 1080 ps minimum. 26) tQHS accounts for: 1) The pulse duration distortion of on-chip clock circuits, which represents how well the actual tHP at the input is transferred to the output; and 2) The worst case push-out of DQS on one transition followed by the worst case pull-in of DQ on the next transition, both of which are independent of each other, due to data pin skew, output pattern effects, and pchannel to n-channel variation of the output drivers. 27) The Auto-Refresh command interval has be reduced to 3.9 s when operating the DDR2 DRAM in a temperature range between 85 C and 95 C. 28) 0 C TCASE 85 C 29) 85 C < TCASE 95 C 30) A maximum of eight Auto-Refresh commands can be posted to any given DDR2 SDRAM device. 31) tRPST end point and tRPRE begin point are not referenced to a specific voltage level but specify when the device output is no longer driving (tRPST), or begins driving (tRPRE). Figure 8 shows a method to calculate these points when the device is no longer driving (tRPST), or begins driving (tRPRE) by measuring the signal at two different voltages. The actual voltage measurement points are not critical as long as the calculation is consistent. Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 48 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM 32) When the device is operated with input clock jitter, this parameter needs to be derated by the actual tJIT.PER of the input clock. (output deratings are relative to the SDRAM input clock.) For example, if the measured jitter into a DDR2-667 SDRAM has tJIT.PER.MIN = - 72 ps and tJIT.PER.MAX = + 93 ps, then tRPRE.MIN(DERATED) = tRPRE.MIN + tJIT.PER.MIN = 0.9 x tCK.AVG - 72 ps = + 2178 ps and tRPRE.MAX(DERATED) = tRPRE.MAX + tJIT.PER.MAX = 1.1 x tCK.AVG + 93 ps = + 2843 ps. (Caution on the MIN/MAX usage!). 33) When the device is operated with input clock jitter, this parameter needs to be derated by the actual tJIT.DUTY of the input clock. (output deratings are relative to the SDRAM input clock.) For example, if the measured jitter into a DDR2-667 SDRAM has tJIT.DUTY.MIN = - 72 ps and tJIT.DUTY.MAX = + 93 ps, then tRPST.MIN(DERATED) = tRPST.MIN + tJIT.DUTY.MIN = 0.4 x tCK.AVG - 72 ps = + 928 ps and tRPST.MAX(DERATED) = tRPST.MAX + tJIT.DUTY.MAX = 0.6 x tCK.AVG + 93 ps = + 1592 ps. (Caution on the MIN/MAX usage!). 34) For these parameters, the DDR2 SDRAM device is characterized and verified to support tnPARAM = RU{tPARAM / tCK.AVG}, which is in clock cycles, assuming all input clock jitter specifications are satisfied. For example, the device will support tnRP = RU{tRP / tCK.AVG}, which is in clock cycles, if all input clock jitter specifications are met. This means: For DDR2-667 5-5-5, of which tRP = 15 ns, the device will support tnRP = RU{tRP / tCK.AVG} = 5, i.e. as long as the input clock jitter specifications are met, Precharge command at Tm and Active command at Tm + 5 is valid even if (Tm + 5 - Tm) is less than 15 ns due to input clock jitter. 35) tWTR is at lease two clocks (2 x tCK) independent of operation frequency. Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 49 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM FIGURE 8 Method for calculating transitions and endpoint FIGURE 9 Differential input waveform timing - tDS and tDS FIGURE 10 Differential input waveform timing - tlS and tlH Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 50 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM TABLE 49 DRAM Component Timing Parameter by Speed Grade - DDR2-533 Parameter Symbol DDR2-533 Min. DQ output access time from CK / CK CAS A to CAS B command period CK, CK high-level width CKE minimum high and low pulse width CK, CK low-level width Auto-Precharge write recovery + precharge time Minimum time clocks remain ON after CKE asynchronously drops LOW DQ and DM input hold time (differential data strobe) Max. +500 -- 0.55 -- 0.55 -- -- -- -- -- +450 -- 300 +0.25 -- -- -- -- ps Unit Note 1)2)3)4)5)6) tAC tCCD tCH tCKE tCL tDAL tDELAY tDH(base) -500 2 0.45 3 0.45 WR + tRP tCK tCK tCK tCK tCK ns ps ps 7)17) tIS + tCK + tIH 225 -25 0.35 -450 0.35 -- -0.25 100 -25 0.2 0.2 MIN. (tCL, tCH) -- 375 0.6 250 2 x tAC.MIN 8) 9) DQ and DM input hold time (single ended data tDH1(base) strobe) DQ and DM input pulse width (each input) DQS output access time from CK / CK DQS input low (high) pulse width (write cycle) DQS-DQ skew (for DQS & associated DQ signals) Write command to 1st DQS latching transition DQ and DM input setup time (differential data strobe) 10) tDIPW tDQSCK tDQSL,H tDQSQ tDQSS tDS(base) tCK ps tCK ps 10) tCK ps ps 10) DQ and DM input setup time (single ended data tDS1(base) strobe) DQS falling edge hold time from CK (write cycle) Clock half period Data-out high-impedance time from CK / CK Address and control input hold time Address and control input pulse width (each input) Address and control input setup time DQ low-impedance time from CK / CK DQS low-impedance from CK / CK Mode register set command cycle time OCD drive mode output delay Data output hold time from DQS Data hold skew factor Average periodic refresh Interval 10) tDSH tCK tCK -- 11) 12) 10) DQS falling edge to CK setup time (write cycle) tDSS tHP tHZ tIH(base) tIPW tIS(base) tLZ(DQ) tLZ(DQS) tMRD tOIT tQH tQHS tREFI tAC.MAX -- -- -- ps ps tCK ps ps ps 10) 13) 13) tAC.MIN 2 0 tAC.MAX tAC.MAX -- 12 -- 400 7.8 tCK ns -- ps s 13)14) tHP - tQHS -- -- Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 51 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM Parameter Symbol DDR2-533 Min. Max. 3.9 -- -- 1.1 0.60 -- -- -- -- 0.60 -- -- -- -- -- -- -- -- Unit Note 1)2)3)4)5)6) Average periodic refresh Interval Auto-Refresh to Active/Auto-Refresh command period Precharge-All (4 banks) command period Read preamble Read postamble Active bank A to Active bank B command period Active bank A to Active bank B command period Internal Read to Precharge command delay Write preamble Write postamble Write recovery time for write without AutoPrecharge Internal Write to Read command delay Exit power down to any valid command (other than NOP or Deselect) Exit active power-down mode to Read command (slow exit, lower power) Exit precharge power-down to any valid command (other than NOP or Deselect) Exit Self-Refresh to non-Read command Exit Self-Refresh to Read command Write recovery time for write with AutoPrecharge 1) VDDQ = 1.8 V 0.1 V; VDD = 1.8 V 0.1 V. tREFI tRFC tRP tRPRE tRPST tRRD tRRD tRTP tWPRE tWPST tWR tWTR tXARD tXARDS tXP tXSNR tXSRD WR -- 105 s ns ns 15)17) 16) tRP 0.9 0.40 7.5 10 7.5 0.25 0.40 15 7.5 2 6 - AL 2 tCK tCK ns ns ns 13) 13) 13)17) 15)21) tCK tCK ns ns 18) 19) 20) tCK tCK tCK ns 20) tRFC +10 200 tWR/tCK tCK tCK 21) 2) Timing that is not specified is illegal and after such an event, in order to guarantee proper operation, the DRAM must be powered down and then restarted through the specified initialization sequence before normal operation can continue. 3) Timings are guaranteed with CK/CK differential Slew Rate of 2.0 V/ns. For DQS signals timings are guaranteed with a differential Slew Rate of 2.0 V/ns in differential strobe mode and a Slew Rate of 1 V/ns in single ended mode. 4) The CK / CK input reference level (for timing reference to CK / CK) is the point at which CK and CK cross. The DQS / DQS, RDQS / RDQS, input reference level is the crosspoint when in differential strobe mode. 5) Inputs are not recognized as valid until VREF stabilizes. During the period before VREF stabilizes, CKE = 0.2 x VDDQ is recognized as low. 6) The output timing reference voltage level is VTT. 7) For each of the terms, if not already an integer, round to the next highest integer. tCK refers to the application clock period. WR refers to the WR parameter stored in the MR. 8) The clock frequency is allowed to change during self-refresh mode or precharge power-down mode. 9) For timing definition, refer to the Component data sheet. 10) Consists of data pin skew and output pattern effects, and p-channel to n-channel variation of the output drivers as well as output Slew Rate mis-match between DQS / DQS and associated DQ in any given cycle. 11) MIN (tCL, tCH) refers to the smaller of the actual clock low time and the actual clock high time as provided to the device (i.e. this value can be greater than the minimum specification limits for tCL and tCH). 12) The tHZ, tRPST and tLZ, tRPRE parameters are referenced to a specific voltage level, which specify when the device output is no longer driving (tHZ, tRPST), or begins driving (tLZ, tRPRE). tHZ and tLZ transitions occur in the same access time windows as valid data transitions.These parameters are verified by design and characterization, but not subject to production test. Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 52 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM 13) The Auto-Refresh command interval has be reduced to 3.9 s when operating the DDR2 DRAM in a temperature range between 85 C and 95 C. 14) 0 C TCASE 85 C 15) 85 C < TCASE 95 C 16) A maximum of eight Auto-Refresh commands can be posted to any given DDR2 SDRAM device. 17) The tRRD timing parameter depends on the page size of the DRAM organization. See Table 5 "Ordering Information for Lead-Free Products (RoHS Compliant)" on Page 6. 18) The maximum limit for the tWPST parameter is not a device limit. The device operates with a greater value for this parameter, but system performance (bus turnaround) degrades accordingly. 19) Minimum tWTR is two clocks when operating the DDR2-SDRAM at frequencies 200 z. 20) User can choose two different active power-down modes for additional power saving via MRS address bit A12. In "standard active powerdown mode" (MR, A12 = "0") a fast power-down exit timing tXARD can be used. In "low active power-down mode" (MR, A12 ="1") a slow power-down exit timing tXARDS has to be satisfied. 21) WR must be programmed to fulfill the minimum requirement for the tWR timing parameter, where WRMIN[cycles] = tWR(ns)/tCK(ns) rounded up to the next integer value. tDAL = WR + (tRP/tCK). For each of the terms, if not already an integer, round to the next highest integer. tCK refers to the application clock period. WR refers to the WR parameter stored in the MRS. TABLE 50 DRAM Component Timing Parameter by Speed Grade - DDR2-400 Parameter Symbol DDR2-400 Min. DQ output access time from CK / CK CAS A to CAS B command period CK, CK high-level width CKE minimum high and low pulse width CK, CK low-level width Auto-Precharge write recovery + precharge time Minimum time clocks remain ON after CKE asynchronously drops LOW DQ and DM input hold time (differential data strobe) Max. +600 -- 0.55 -- 0.55 -- -- -- -- -- +500 -- 350 +0.25 -- -- -- -- ps Unit Note 1)2)3)4)5)6) tAC tCCD tCH tCKE tCL tDAL tDELAY tDH(base) -600 2 0.45 3 0.45 WR + tRP tCK tCK tCK tCK tCK ns ps ps 7)20) tIS + tCK + tIH 275 -25 0.35 -500 0.35 -- -0.25 150 -25 0.2 0.2 8) 9) DQ and DM input hold time (single ended data tDH1(base) strobe) DQ and DM input pulse width (each input) DQS output access time from CK / CK DQS input low (high) pulse width (write cycle) DQS-DQ skew (for DQS & associated DQ signals) DQ and DM input setup time (differential data strobe) DQ and DM input setup time (single ended data strobe) DQS falling edge hold time from CK (write cycle) 10) tDIPW tDQSCK tDQSL,H tDQSQ tCK ps tCK ps 10) Write command to 1st DQS latching transition tDQSS tCK ps ps 10) tDS(base) tDS1(base) tDSH 10) tCK tCK DQS falling edge to CK setup time (write cycle) tDSS Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 53 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM Parameter Symbol DDR2-400 Min. Max. Unit Note 1)2)3)4)5)6) Clock half period Data-out high-impedance time from CK / CK Address and control input hold time Address and control input pulse width (each input) Address and control input setup time DQ low-impedance time from CK / CK DQS low-impedance from CK / CK Mode register set command cycle time OCD drive mode output delay Data output hold time from DQS Data hold skew factor Average periodic refresh Interval Average periodic refresh Interval Auto-Refresh to Active/Auto-Refresh command period Precharge-All (4 banks) command period Read preamble Read postamble Active bank A to Active bank B command period Active bank A to Active bank B command period Internal Read to Precharge command delay Write preamble Write postamble Write recovery time for write without AutoPrecharge Internal Write to Read command delay Exit power down to any valid command (other than NOP or Deselect) Exit active power-down mode to Read command (slow exit, lower power) Exit precharge power-down to any valid command (other than NOP or Deselect) Exit Self-Refresh to non-Read command Exit Self-Refresh to Read command Write recovery time for write with AutoPrecharge 1) VDDQ = 1.8 V 0.1 V; VDD = 1.8 V 0.1 V. tHP tHZ tIH(base) tIPW tIS(base) tLZ(DQ) tLZ(DQS) tMRD tOIT tQH tQHS tREFI tREFI -- MIN. (tCL, tCH) -- 475 0.6 350 2 x tAC.MIN -- 11) 12) 10) tAC.MAX -- -- -- ps ps tCK ps ps ps 10) 13) 13) tAC.MIN 2 0 tAC.MAX tAC.MAX -- 12 -- 450 7.8 3.9 -- -- 1.1 0.60 -- -- -- -- 0.60 -- -- -- -- -- -- -- -- tCK ns -- ps s s ns ns 13)14) 15)17) 16) tHP -tQHS -- -- -- 105 tRP tRPRE tRPST tRRD tRRD tRTP tWPRE tWPST tWR tWTR tXARD tXARDS tXP tXSNR tXSRD WR tRP 0.9 0.40 7.5 10 7.5 0.25 0.40 15 10 2 6 - AL 2 tCK tCK ns ns ns 13) 13) 13)17) 15)21) tCK tCK ns ns 18) 19) 20) tCK tCK tCK ns 20) tRFC +10 200 tWR/tCK tCK tCK 21) 2) Timing that is not specified is illegal and after such an event, in order to guarantee proper operation, the DRAM must be powered down and then restarted through the specified initialization sequence before normal operation can continue. Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 54 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM 3) Timings are guaranteed with CK/CK differential Slew Rate of 2.0 V/ns. For DQS signals timings are guaranteed with a differential Slew Rate of 2.0 V/ns in differential strobe mode and a Slew Rate of 1 V/ns in single ended mode. 4) The CK / CK input reference level (for timing reference to CK / CK) is the point at which CK and CK cross. The DQS / DQS, RDQS / RDQS, input reference level is the crosspoint when in differential strobe mode. 5) Inputs are not recognized as valid until VREF stabilizes. During the period before VREF stabilizes, CKE = 0.2 x VDDQ is recognized as low. 6) The output timing reference voltage level is VTT. 7) For each of the terms, if not already an integer, round to the next highest integer. tCK refers to the application clock period. WR refers to the WR parameter stored in the MR. 8) The clock frequency is allowed to change during self-refresh mode or precharge power-down mode. 9) For timing definition, refer to the Component data sheet. 10) Consists of data pin skew and output pattern effects, and p-channel to n-channel variation of the output drivers as well as output Slew Rate mis-match between DQS / DQS and associated DQ in any given cycle. 11) MIN (tCL, tCH) refers to the smaller of the actual clock low time and the actual clock high time as provided to the device (i.e. this value can be greater than the minimum specification limits for tCL and tCH). 12) The tHZ, tRPST and tLZ, tRPRE parameters are referenced to a specific voltage level, which specify when the device output is no longer driving (tHZ, tRPST), or begins driving (tLZ, tRPRE). tHZ and tLZ transitions occur in the same access time windows as valid data transitions.These parameters are verified by design and characterization, but not subject to production test. 13) The Auto-Refresh command interval has be reduced to 3.9 s when operating the DDR2 DRAM in a temperature range between 85 C and 95 C. 14) 0 C TCASE 85 C 15) 85 C < TCASE 95 C 16) A maximum of eight Auto-Refresh commands can be posted to any given DDR2 SDRAM device. 17) The tRRD timing parameter depends on the page size of the DRAM organization. See Table 5 "Ordering Information for Lead-Free Products (RoHS Compliant)" on Page 6. 18) The maximum limit for the tWPST parameter is not a device limit. The device operates with a greater value for this parameter, but system performance (bus turnaround) degrades accordingly. 19) Minimum tWTR is two clocks when operating the DDR2-SDRAM at frequencies 200 z. 20) User can choose two different active power-down modes for additional power saving via MRS address bit A12. In "standard active powerdown mode" (MR, A12 = "0") a fast power-down exit timing tXARD can be used. In "low active power-down mode" (MR, A12 ="1") a slow power-down exit timing tXARDS has to be satisfied. 21) WR must be programmed to fulfill the minimum requirement for the tWR timing parameter, where WRMIN[cycles] = tWR(ns)/tCK(ns) rounded up to the next integer value. tDAL = WR + (tRP/tCK). For each of the terms, if not already an integer, round to the next highest integer. tCK refers to the application clock period. WR refers to the WR parameter stored in the MRS. Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 55 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM 7.3 Jitter Definition and Clock Jitter Specification Generally, jitter is defined as "the short-term variation of a signal with respect to its ideal position in time". The following table provides an overview of the terminology. TABLE 51 Average Clock and Jitter Symbols and Definition Symbol Parameter Description Units ps tCK.AVG Average clock period tCK.AVG is calculated as the average clock period within any consecutive 200-cycle window: N 1 . tCK.AVG = --- tCK j N j = 1 N = 200 (1) tJIT.PER Clock-period jitter tJIT.PER is defined as the largest deviation of any single tCK from tCK.AVG: tJIT.PER = Min/Max of {tCKi - tCK.AVG} where i = 1 to 200 ps tJIT(PER, LCK) Clock-period jitter during DLL-locking period Cycle-to-cycle clock period jitter tJIT.PER defines the single-period jitter when the DLL is already locked. tJIT.PER is not guaranteed through final production testing. tJIT(PER,LCK) uses the same definition as tJIT.PER, during the DLL-locking ps period only. tJIT.CC tJIT(PER,LCK) is not guaranteed through final production testing. tJIT.CC is defined as the absolute difference in clock period between two consecutive clock cycles: tJIT.CC = Max of ABS{tCKi+1 - tCKi} ps tJIT(CC, LCK) Cycle-to-cycle clock period jitter during DLL-locking period Cumulative error across 2 cycles tJIT.CC defines the cycle- to- cycle jitter when the DLL is already locked. tJIT.CC is not guaranteed through final production testing. tJIT(CC,LCK) uses the same definition as tJIT.CC during the DLL-locking period only. tJIT(CC,LCK) is not guaranteed through final production testing. ps tERR.2PER tERR.2PER is defined as the cumulative error across 2 consecutive cycles from tCK.AVG: ps i + n - 1 tERR ( 2per ) = tCK j - n x tCK ( avg ) j=i n = 2 for tERR(2per) where i = 1 to 200 (2) Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 56 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM Symbol Parameter Cumulative error across n cycles Description Units ps tERR.nPER tERR.2PER is defined as the cumulative error across n consecutive cycles from tCK.AVG: i + n - 1 tERR ( nper ) = tCK j - n x tCK ( avg ) j=i where, i = 1 to 200 and n = 3 for tERR.3PER n = 4 for tERR.4PER n = 5 for tERR.5PER 6 n 10 for tERR.6-10PER 11 n 50 for tERR.11-50PER (3) tCH.AVG Average high-pulse width tCH.AVG is defined as the average high-pulse width, as calculated across any consecutive 200 high pulses: tCK.AVG N 1 . tCH ( avg ) = ---------------------------------------- tCH j ( N x tCK ( avg ) ) j = 1 N = 200 (4) tCL.AVG Average low-pulse width tCL.AVG is defined as the average low-pulse width, as calculated across any tCK.AVG consecutive 200 low pulses: N 1 tCL ( avg ) = --------------------------------------- . tCL j ( N x tCK ( avg ) ) j = 1 N = 200 (5) tJIT.DUTY Duty-cycle jitter tJIT.DUTY = Min/Max of {tJIT.CH , tJIT.CL}, where: tJIT.CH is the largest deviation of any single tCH from tCH.AVG tJIT.CL is the largest deviation of any single tCL from tCL.AVG tJIT.CH = {tCHi - tCH.AVG x tCK.AVG} where i=1 to 200 tJIT.CL = {tCLi - tCL.AVG x tCK.AVG} where i=1 to 200 ps Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 57 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM The following parameters are specified per their average values however, it is understood that the following relationship between the average timing and the absolute instantaneous timing holds all the time. TABLE 52 Absolute Jitter Value Definitions Symbol Parameter Clock period Clock high-pulse width Clock low-pulse width Min. Max. Unit ps ps ps tCK.ABS tCH.ABS tCL.ABS tCK.AVG(Min) + tJIT.PER(Min) tCK.AVG(Max) + tJIT.PER(Max) tCH.AVG(Min) x tCK.AVG(Min) + tJIT.DUTY(Min) tCH.AVG(Max) x tCK.AVG(Max) + tJIT.DUTY(Max) tCL.AVG(Min) x tCK.AVG(Min) + tJIT.DUTY(Min) tCL.AVG(Max) x tCK.AVG(Max) + tJIT.DUTY(Max) Example: for DDR2-667, tCH.ABS(Min) = (0.48 x 3000ps) - 125 ps = 1315 ps = 0.438 x 3000 ps. Table 53 shows clock-jitter specifications. TABLE 53 Clock-Jitter Specifications for -667 and -800 Symbol Parameter DDR2 -667 Min. Max. 8000 +125 +100 +250 +200 +175 +225 +250 +250 +350 +450 0.52 0.52 +125 DDR2 -800 Min. 2500 -100 -80 -200 -160 -150 -175 -200 -200 -300 -450 0.48 0.48 -100 Max. 8000 +100 +80 +200 +160 +150 +175 +200 +200 +300 +450 0.52 0.52 +100 ps ps ps ps ps ps ps ps ps ps ps Unit tCK.AVG tJIT.PER tJIT(PER,LCK) tJIT.CC tJIT(CC,LCK) tERR.2PER tERR.3PER tERR.4PER tERR.5PER tERR(6-10PER) tERR(11-50PER) tCH.AVG tCL.AVG tJIT.DUTY Average clock period nominal w/o jitter Clock-period jitter Clock-period jitter during DLL locking period Cycle-to-cycle clock-period jitter Cycle-to-cycle clock-period jitter during DLLlocking period Cumulative error across 2 cycles Cumulative error across 3 cycles Cumulative error across 4 cycles Cumulative error across 5 cycles Cumulative error across n cycles with n = 6 .. 10, inclusive 3000 -125 -100 -250 -200 -175 -225 -250 -250 -350 Cumulative error across n cycles with n = 11 .. -450 50, inclusive Average high-pulse width Average low-pulse width Duty-cycle jitter 0.48 0.48 -125 tCK.AVG tCK.AVG ps Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 58 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM 7.4 ODT AC Electrical Characteristics TABLE 54 ODT AC Characteristics and Operating Conditions for DDR2-533 and DDR2-400 This chapter describes the ODT AC electrical characteristics. Symbol Parameter / Condition Values Min. Max. 2 Unit Note tAOND tAON tAONPD tAOFD tAOF tAOFPD tANPD tAXPD ODT turn-on delay ODT turn-on ODT turn-on (Power-Down Modes) ODT turn-off delay ODT turn-off ODT turn-off (Power-Down Modes) ODT to Power Down Mode Entry Latency ODT Power Down Exit Latency 2 tCK ns ns 1) tAC.MIN tAC.MIN + 2 ns 2.5 tAC.MAX + 1 ns 2 tCK + tAC.MAX + 1 ns 2.5 tCK ns ns 2) tAC.MIN tAC.MIN + 2 ns 3 8 tAC.MAX + 0.6 ns 2.5 tCK + tAC.MAX + 1 ns -- -- tCK tCK 1) ODT turn on time min. is when the device leaves high impedance and ODT resistance begins to turn on. ODT turn on time max is when the ODT resistance is fully on. Both are measured from tAOND, which is interpreted differently per speed bin. For DDR2-400/533, tAOND is 10 ns (= 2 x 5 ns) after the clock edge that registered a first ODT HIGH if tCK = 5 ns. 2) ODT turn off time min. is when the device starts to turn off ODT resistance. ODT turn off time max is when the bus is in high impedance. Both are measured from tAOFD. Both are measured from tAOFD, which is interpreted differently per speed bin. For DDR2-400/533, tAOFD is 12.5 ns (= 2.5 x 5 ns) after the clock edge that registered a first ODT HIGH if tCK = 5 ns. TABLE 55 ODT AC Characteristics and Operating Conditions for DDR2-667 and DDR2-800 Symbol Parameter / Condition Values Min. Max. 2 Unit Note tAOND tAON tAONPD tAOFD tAOF tAOFPD tANPD tAXPD ODT turn-on delay ODT turn-on ODT turn-on (Power-Down Modes) ODT turn-off delay ODT turn-off ODT turn-off (Power-Down Modes) ODT to Power Down Mode Entry Latency ODT Power Down Exit Latency 2 nCK ns ns 1) 1)2) 1) 1) 1)3) 1) 1) 1) tAC.MIN tAC.MIN + 2 ns 2.5 tAC.MAX + 0.7 ns 2 tCK + tAC.MAX + 1 ns 2.5 nCK ns ns tAC.MIN tAC.MIN + 2 ns 3 8 tAC.MAX + 0.6 ns 2.5 tCK + tAC.MAX + 1 ns -- -- nCK nCK 1) New units, "tCK.AVG" and "nCK", are introduced in DDR2-667 and DDR2-800. Unit "tCK.AVG" represents the actual tCK.AVG of the input clock under operation. Unit "nCK" represents one clock cycle of the input clock, counting the actual clock edges. Note that in DDR2-400 and DDR2-533, "tCK" is used for both concepts. Example: tXP = 2 [nCK] means; if Power Down exit is registered at Tm, an Active command may be registered at Tm + 2, even if (Tm + 2 - Tm) is 2 x tCK.AVG + tERR.2PER(Min). 2) ODT turn on time min is when the device leaves high impedance and ODT resistance begins to turn on. ODT turn on time max is when the ODT resistance is fully on. Both are measured from tAOND, which is interpreted differently per speed bin. For DDR2-667/800, tAOND is 2 clock cycles after the clock edge that registered a first ODT HIGH counting the actual input clock edges. 3) ODT turn off time min is when the device starts to turn off ODT resistance. ODT turn off time max is when the bus is in high impedance. Both are measured from tAOFD, which is interpreted differently per speed bin. For DDR2-667/800, if tCK(avg) = 3 ns is assumed, tAOFD is 1.5 ns (= 0.5 x 3 ns) after the second trailing clock edge counting from the clock edge that registered a first ODT LOW and by counting the actual input clock edges. Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 59 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM 8 Package Dimensions FIGURE 11 Package Outline P(G)-TFBGA-84-51 This chapter describes the package dimensions. Notes 1. Drawing according to ISO 8015 2. Dimensions in mm 3. General tolerances +/- 0.15 Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 60 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM FIGURE 12 Package Outline P-TFBGA-84-1 Notes 1. Drawing according to ISO 8015 2. Dimensions in mm 3. General tolerances +/- 0.15 Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 61 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM FIGURE 13 Package Outline P(G)-TFBGA-60-6 Notes 1. Drawing according to ISO 8015 2. Dimensions in mm 3. General tolerances +/- 0.15 Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 62 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM 9 Product Nomenclature TABLE 56 Examples for Nomenclature Fields For reference the Qimonda SDRAM component nomenclature is enclosed in this chapter. Example for Field Number 1 2 18 18 3 T T 4 512 512 5 4 16 6 7 0 0 8 A B 9 F F 10 -- L 11 -3 -3.7 DDR2 SDRAM DDR2 SDRAM HYB HYB TABLE 57 DDR2 Memory Components Field 1 2 3 4 Description Qimonda Component Prefix Interface Voltage [V] DRAM Technology Component Density [Mbit] Values HYB 18 T 256 512 1G 2G 5+6 Number of I/Os 40 80 16 7 8 Product Variations Die Revision 0 .. 9 A B C 9 10 11 Package, Lead-Free Status Power Speed Grade C F - L -1.9 -25F -2.5 -3 -3S -3.7 -5 Coding Constant SSTL_18 DDR2 256 Mbit 512 Mbit 1 Gbit 2 Gbit x4 x8 x16 look up table First Second Third FBGA, lead-containing FBGA, lead-free Standard power product Low power product DDR2-1066 DDR2-800 5-5-5 DDR2-800 6-6-6 DDR2-667 4-4-4 DDR2-667 5-5-5 DDR2-533 4-4-4 DDR2-400 3-3-3 Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 63 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM List of Figures Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 Figure 6 Figure 7 Figure 8 Figure 9 Figure 10 Figure 11 Figure 12 Figure 13 Chip Configuration for x4 components, PG-TFBGA-60 (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chip Configuration for x8 components, PG-TFBGA-60 (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chip Configuration for x16 components, PG-TFBGA-84 (top view) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Single-ended AC Input Test Conditions Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Differential DC and AC Input and Output Logic Levels Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC Overshoot / Undershoot Diagram for Address and Control Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC Overshoot / Undershoot Diagram for Clock, Data, Strobe and Mask Pins . . . . . . . . . . . . . . . . . . . . . . . . . Method for calculating transitions and endpoint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Differential input waveform timing - tDS and tDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Differential input waveform timing - tlS and tlH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Package Outline P(G)-TFBGA-84-51 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Package Outline P-TFBGA-84-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Package Outline P(G)-TFBGA-60-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 14 15 30 31 35 36 50 50 50 60 61 62 Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 64 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM List of Tables Table 1 Table 2 Table 3 Table 4 Table 5 Table 6 Table 7 Table 8 Table 9 Table 10 Table 11 Table 12 Table 13 Table 14 Table 15 Table 16 Table 17 Table 18 Table 19 Table 20 Table 21 Table 22 Table 23 Table 24 Table 25 Table 26 Table 27 Table 28 Table 29 Table 30 Table 31 Table 32 Table 33 Table 34 Table 35 Table 36 Table 37 Table 38 Table 39 Table 40 Table 41 Table 42 Table 43 Table 44 Table 45 Table 46 Table 47 Table 48 Table 49 Performance Table for -25F and -2.5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Performance table for -3(S) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Performance Table for -3.7(F) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Performance Table for -5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Ordering Information for Lead-Free Products (RoHS Compliant). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Ordering Information for Lead-Containing Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Chip Configuration of DDR2 SDRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Abbreviations for Ball Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Abbreviations for Buffer Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 DDR2 Addressing for x4 Organization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 DDR2 Addressing for x8 Organization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 DDR2 Addressing for x16 Organization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Mode Register Definition (BA[2:0] = 000B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Extended Mode Register Definition (BA[2:0] = 001B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 EMRS(2) Programming Extended Mode Register Definition (BA[2:0]=010B) . . . . . . . . . . . . . . . . . . . . . . . . . . 21 EMR(3) Programming Extended Mode Register Definition(BA[2:0]=011B) . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 ODT Truth Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Burst Length and Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Command Truth Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Clock Enable (CKE) Truth Table for Synchronous Transitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Data Mask (DM) Truth Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 DRAM Component Operating Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Recommended DC Operating Conditions (SSTL_18) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 ODT DC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Input and Output Leakage Currents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 DC & AC Logic Input Levels for DDR2-667 and DDR2-800 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 DC & AC Logic Input Levels for DDR2-533 and DDR2-400 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Single-ended AC Input Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Differential DC and AC Input and Output Logic Levels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 SSTL_18 Output DC Current Drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 SSTL_18 Output AC Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 OCD Default Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Input / Output Capacitance for DDR2-800 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Input / Output Capacitance for DDR2-667 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Input / Output Capacitance for DDR2-533 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Input / Output Capacitance for DDR2-400 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 AC Overshoot / Undershoot Specification for Address and Control Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 AC Overshoot / Undershoot Spec. for Clock, Data, Strobe and Mask Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 IDD Measurement Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Definition for IDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 IDDSpecification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Speed Grade Definition Speed Bins for DDR2-800 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Speed Grade Definition Speed Bins for DDR2-667 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Speed Grade Definition Speed Bins for DDR2-533 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Speed Grade Definition Speed Bins for DDR2-400B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 DRAM Component Timing Parameter by Speed Grade - DDR2-800 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 DRAM Component Timing Parameter by Speed Grade - DDR2-667 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 DRAM Component Timing Parameter by Speed Grade - DDR2-533 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 65 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM Table 50 Table 51 Table 52 Table 53 Table 54 Table 55 Table 56 Table 57 DRAM Component Timing Parameter by Speed Grade - DDR2-400. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Average Clock and Jitter Symbols and Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Absolute Jitter Value Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Clock-Jitter Specifications for -667 and -800 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ODT AC Characteristics and Operating Conditions for DDR2-533 and DDR2-400 . . . . . . . . . . . . . . . . . . . . . ODT AC Characteristics and Operating Conditions for DDR2-667 and DDR2-800 . . . . . . . . . . . . . . . . . . . . . Examples for Nomenclature Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DDR2 Memory Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 56 58 58 59 59 63 63 Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 66 Internet Data Sheet HYB18T512[40/80/16]0B[C/F] 512-Mbit Double-Data-Rate-Two SDRAM Table of Contents 1 1.1 1.2 2 2.1 2.2 3 4 5 5.1 5.2 5.3 5.4 5.5 5.6 6 7 7.1 7.2 7.3 7.4 8 9 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Chip Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Chip Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Truth Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DC & AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Output Buffer Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Input / Output Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Overshoot and Undershoot Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Timing Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Speed Grade Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Component AC Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Jitter Definition and Clock Jitter Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ODT AC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 27 28 29 31 33 35 40 40 43 56 59 Currents Measurement Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Package Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Product Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Rev. 1.1, 2007-05 03292006-YBYM-WG0Z 67 Internet Data Sheet Edition 2007-05 Published by Qimonda AG Gustav-Heinemann-Ring 212 D-81739 Munchen, Germany (c) Qimonda AG 2007. All Rights Reserved. Legal Disclaimer The information given in this Internet Data Sheet shall in no event be regarded as a guarantee of conditions or characteristics ("Beschaffenheitsgarantie"). With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Qimonda hereby disclaims any and all warranties and liabilities of any kind, including without limitation warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices please contact your nearest Qimonda Office. Warnings Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Qimonda Office. Qimonda Components may only be used in life-support devices or systems with the express written approval of Qimonda, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. www.qimonda.com |
Price & Availability of HYB18T512160BF-25 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |