View VC-2R8A26-2143_1334172.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

FUJITSU MEDIA DEVICE DATA SHEET
DS04-21714-1E
ASSP for Mobile Telephone
VCO (800 to 2000 MHz) VC-26 Series
s DESCRIPTION
With excellent C/N characteristics and low current consumption, this VCO series is suitable for use with AMPS, CDMA and PCS and is ideal to miniaturize, dual-band mode products. The VC-26 series can be used in any frequency band in the 800MHz to 2000MHz range. The device utilizes FUJITSU MEDIA DEVICE's high-frequency design technology, high-density mounting technology, and frequency adjustment technology to provide a high level of reliability in addition to high performance and small size.
s FEATURES
Superior noise characteristics (C/N, S/N) Frequency switching type with an internal switching transistor High level of stability in response to ambient temperature and load variations FUJITSU MEDIA DEVICE's proprietary fabrication process provides the uniformity of the central frequency distribution * Small size, light-weight, slim-package : 9.3 x 7.3 x 2.0 mm (Max.) * SMD-type taping specifications suitable for automatic mounting and reflow soldering * * * *
s PACKAGE
VC-26 Series
s PIN ASSIGNMENT
(TOP VIEW)
6
5
4
7
8
1
2
3
s PIN DESCRIPTION
Pin No. 1 2 3 4 5 6 7 8 Symbol Vt GND VCC OUT GND VSW GND GND GND Power supply voltage Output GND Band select GND GND Description Control voltage
s PRODUCT LINEUP (STANDARD MODELS)
System AMPS*CDMA/PCS Center Frequency (MHz) 1065 2143 Band Width (MHz) 13 30.5 Power Supply Voltage (V) 2.8 0.1 Part Number VC-2R8A26-1065/2143
2
VC-26 Series
s ELECTRICAL CHARACTERISTICS
* Absolute Maximum Ratings Parameter Input DC voltage Control voltage SW voltage Operating temperature Storage temperature Storage humidity Symbol VCC Vt VSW Ta Tstg Hstg Rating Min. -0.6 -0.6 -0.6 -30 -30 5 Max. + 6.0 + 6.0 + 6.0 +85 +85 95 Unit V V V C C %
WARNING: VCO can be permanently damaged by application of stress (voltage, temperature, humidity, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
* Band Selection Mode Band Width CDMA PCS Selection Mode Band1 Band2 VSW (V) Min. 0.0 2.65 Max. 0.15 2.8 Center Frequency (MHz) 1065 2143 Current Consumption (A) Typ. -45.0 0.0
3
VC-26 Series
* Electrical Characteristics Band1 Value Min. 1078.0 20.0 -4.5 Typ. 45.0 0.0 Max. 15.0 100.0 1052.0 30.0 3.0 -119.0 -117.0 -123.0 -131.0 -137.0 -140.0 -141.0 -160.0 -10.0 -80.0 1000 700 3000 dBc dBc kHz kHz kHz dBc/Hz
(Ta = -30C to +85C) Conditions VCC = 2.8 V, Vt = 1.425 V VCC = 2.8 V, Vt = 1.425 V, VSW = 0 V VCC = 2.8 V, Vt = 0.5 V VCC = 2.8 V, Vt = 2.35 V (fmax - fmin) / 1.85 VCC = 2.8 V, Vt = 1.425 V, Ta = 25C VCC = 2.8 V, Vt = 1.425 V Offset = 60 kHz, BW = 1 Hz, Ta = 25C Offset = 60 kHz, BW = 1 Hz Offset = 120 kHz, BW = 1 Hz Offset = 330 kHz, BW = 1 Hz Offset = 660 kHz, BW = 1 Hz Offset = 900 kHz, BW = 1 Hz Offset = 1700 kHz, BW = 1 Hz Offset 45 MHz, BW = 1 Hz VCC = 2.8 V, Vt = 1.425 V, Up to 3rd VCC = 2.8 V, Vt = 1.425 V VCC = 2.8 V 0.1 V, Vt = 1.425 V VCC = 2.8 V, Vt = 1.425 V, VSWR = 2, All phase Ta = +25 (+60/-55) C Unit mA A MHz MHz MHz/V
Parameter Current consumption SW current Frequency Frequency Control voltage sensitivity Oscillator output
Symbol ICC ISW fmin fmax Svt
PO
dBm
C/N
C/N
Higher harmonics Spurious Power supply variation Load variation Temperature drift
Hs Sp Push Pull Td
4
VC-26 Series
Band2 Value Min. 2174.0 40.0 -4.5 Typ. 0.0 Max. 15.0 2113.0 60.0 3.0 -117.0 -139.0 -137.0 -140.0 -160.0 -10.0 -80.0 1000 700 6000 dBc dBc kHz kHz kHz dBc/Hz (Ta = -30C to +85C) Symbol ICC fmin fmax Svt Conditions VCC = 2.8 V, Vt = 1.425 V VCC = 2.8 V, Vt = 0.5 V VCC = 2.8 V, Vt = 2.35 V (fmax - fmin) / 1.85 VCC = 2.8 V, Vt = 1.425 V, Ta = +25C VCC = 2.8 V, Vt = 1.425 V Offset = 120 kHz, BW = 1 Hz Offset = 1250 kHz, BW = 1 Hz, Ta = +25C C/N C/N Offset = 1250 kHz, BW = 1 Hz Offset = 2050 kHz, BW = 1 Hz Offset 80 MHz, BW = 1 Hz Higher harmonics Spurious Power supply variation Load variation Temperature drift Hs Sp Push Pull Td VCC = 2.8 V, Vt = 1.425 V, Up to 3rd VCC = 2.8 V, Vt = 1.425 V VCC = 2.8 V 0.1 V VCC = 2.8 V, Vt = 1.425 V, VSWR = 2, All phase Ta = +25 (+60/-55) C Unit mA MHz MHz MHz/V
Parameter Current consumption Frequency Frequency Control voltage sensitivity Oscillator output
PO
dBm
5
VC-26 Series
s MARKING
6
5
4
Part symbol Lot number
7 8
Logo Index
1 2 3
s PART NUMBER DESIGNATION
VC - 2R8 A 26 - 1065/2143 Center Frequency Series Name Outer Sheath Type Power Supply Voltage Product Category
Band 2
: SMD
Band 1 : 1065 MHz : 2143 MHz : VC-26 Series : 2.8 V : VCO
6
VC-26 Series
s PACKAGE DIMENSION
9.0 -0.2
+0.3
1.0
2.8
1 7.0 0.3 7 6
2
3 8 2.8 5.0
5
4
1.0
2.0 Max.
5.8
Dimensions in mm
s RECOMMENDED PATTERN FOR SOLDERING
5.8 1.0 2.8 5.2 1.0 2.8
8.0 10.6
7.6
Dimensions in mm Dimension tolerance : 0.1 mm
7
VC-26 Series
s TAPING AND PACKAGING
(1) Carrier Tape and Packaging
2.0 0.1
4.0 0.1
7.5 0.1 1.75 0.1
1.5
+0.1 -0
2.8 0.1
9.8 0.1
1.5 -0 12.0 0.1 7.4 0.1
+0.1
16.0 0.3
0.3 0.05
Dimensions in mm
(2) Taping Layout
Feeder
150 mm 360 mm
Direction of pulling Reel side Rulling side
Empty 50 mm or more
Marking of pin 1
Empty 400 mm or more
1000 packages
8
VC-26 Series
(3) Reel Shape and Dimensions
25.4 Max.
330.0 2.0
80.0 1.5
21.0 0.5
Label
3.0 0.5 16.4 -0
+2.0
Note : The label specifies the part number, quantity, and lot number.
Volume : 1000 pcs/reel Type : (L) 340 x (W) 340 x (t) 30 (mm)
13.0 0.3
Dimensions in mm
9
VC-26 Series
s REFLOW MOUNTING CONDITIONS (RECOMMENDED)
* Perform mounting using the temperature profile shown below. To prevent thermal stress to the VCO, ensure gentle temperature gradients and use preheating whenever possible. (Recommended preheating: 140C to 160C for 60 s 20 s) * Always consult FUJITSU MEDIA DEVICE beforehand if mounting more than once. * Never remove a VCO that has already been mounted and attempt to reuse. * For mounting, use a general-purpose flux suitable for mounting electronic components.
250 230 10 200
7 s Max.
2 1 20 s 30 s
Temperature (C)
160 150 140 60 s 20 s
100
50
Warm-up
0
Pre-heating Time (s)
Heating
Cooling 1 : 10 C/s or less 2 : 8 C/s or less
s WASHING CONDITIONS
* Washing solution: Use isopropyl alcohol. * Washing procedure: Immersion or steam cleaning is recommended. * Washing time: For immersion: Less than 5 minutes at 40C or less. For steam: Less than 2 minutes at 90C or less is recommended.
10
VC-26 Series
FUJITSU MEDIA DEVICES LIMITED
For further information please contact: Japan FUJITSU MEDIA DEVICE LIMITED International Sales & Marketing DEPT. Shin-Yokohama Square Bldg.,14F, Shin-yokohama 2-3-12, Kohoku-ku, Yokohama, Kanagawa 222-0033, Japan Tel: +81-45-471-0061 Fax: +81-45-471-0076
http://www.fujitsu.co.jp/hypertext/fmd/English/index.html
All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with FUJITSU sales representatives before ordering. The information and circuit diagrams in this document are presented as examples of semiconductor device applications, and are not intended to be incorporated in devices for actual use. Also, FUJITSU is unable to assume responsibility for infringement of any patent rights or other rights of third parties arising from the use of this information or circuit diagrams. The contents of this document may not be reproduced or copied without the permission of FUJITSU LIMITED. FUJITSU semiconductor devices are intended for use in standard applications (computers, office automation and other office equipments, industrial, communications, and measurement equipments, personal or household devices, etc.). CAUTION: Customers considering the use of our products in special applications where failure or abnormal operation may directly affect human lives or cause physical injury or property damage, or where extremely high levels of reliability are demanded (such as aerospace systems, atomic energy controls, sea floor repeaters, vehicle operating controls, medical devices for life support, etc.) are requested to consult with FUJITSU sales representatives before such use. The company will not be responsible for damages arising from such use without prior approval. Any semiconductor devices have inherently a certain rate of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Control Law of Japan, the prior authorization by Japanese government should be required for export of those products from Japan.
North and South America FUJITSU MICROELECTRONICS, INC. 3545 North First Street, San Jose, CA 95134-1804, U.S.A. Tel: +1-408-922-9000 Fax: +1-408-922-9179 Customer Response Center Mon. - Fri.: 7 am - 5 pm (PST) Tel: +1-800-866-8608 Fax: +1-408-922-9179 http://www.fujitsumicro.com/ Europe FUJITSU MICROELECTRONICS EUROPE GmbH Am Siebenstein 6-10, D-63303 Dreieich-Buchschlag, Germany Tel: +49-6103-690-0 Fax: +49-6103-690-122 http://www.fujitsu-fme.com/ Asia Pacific FUJITSU MICROELECTRONICS ASIA PTE. LTD. #05-08, 151 Lorong Chuan, New Tech Park, Singapore 556741 Tel: +65-281-0770 Fax: +65-281-0220 http://www.fmap.com.sg/
F0101 (c) FUJITSU LIMITED Printed in Japan

▲Up To Search▲

Price & Availability of VC-2R8A26-2143

	To Download VC-2R8A26-2143 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .