 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Product Specification PE4261 FLIP CHIP SP4T UltraCMOSTM 2.6 V Switch 100 - 3000 MHz Figure 1. Functional Diagram Features * Two pin CMOS logic control inputs * Low TX insertion loss: 0.55 dB at * TX1 RX1 * TX2 RX2 * * * * CMOS Control/Driver and ESD 900 MHz, 0.70 dB at 1900 MHz Isolation of 39 dB at 900 MHz, 31 dB at 1900 MHz Low harmonics 2fo = -82 dBc and 3fo = -74 dBc at 35 dBm input power 1500 V HBM ESD tolerance Built in CMOS decoder/driver RX SAW over voltage protection circuit No blocking capacitors required V1 V2 Product Description The PE4261 SP4T RF UltraCMOSTM Flip Chip Switch is designed specifically to address the needs of the antenna switch module market for GSM Handsets. On-chip CMOS decode logic is used to facilitate two-pin, low voltage CMOS control inputs. High ESD tolerance of 1500 V at all ports, no blocking capacitor requirements and on-chip SAW filter overvoltage protection devices make this the ultimate in integration and ease of use. The PE4261 is manufactured on Peregrine's UltraCMOSTM process, a patented variation of silicon-on-insulator (SOI) technology on a sapphire substrate, offering the performance of GaAs with the economy and integration of conventional CMOS. Figure 2. Die Top View 10 TX1 11 N/C 12 ANT 1 RX1 9 GND 2 GND 8 TX2 GND 7 VDD 6 V2 5 3 RX2 V1 4 Document No. 70-0188-02 www.psemi.com NDA required for full version: Contact sales@psemi.com (c)2005-2006 Peregrine Semiconductor Corp. All rights reserved. Page 1 of 4 PE4261 Product Specification Table 1. PE4261 Electrical Specifications: Temp = 25C, VDD = 2.6 V Parameter Operational Frequency ANT - TX - 850 / 900 MHz ANT - TX - 1800 / 1900 MHz ANT - RX - 850 / 900 MHz ANT - RX - 1800 / 1900 MHz TX - RX - 850 / 900 MHz (TX ON) TX - RX - 1800 / 1900 MHz (TX ON) TX1 - TX2 - 850 / 900 MHz (TX1 ON) TX1 - TX2 - 1800 / 1900 MHz (TX1 ON) 850 / 900 MHz 1800 / 1900 MHz 35 dBm TX Input Power - 850 / 900 MHz 33 dBm TX Input Power - 1800 / 1900 MHz 35 dBm TX Input Power - 850 / 900 MHz 33 dBm TX Input Power - 1800 / 1900 MHz (10-90%) (90-10%) RF 37 29 33 26 18 14 Condition Min 100 Typ Max 3000 Unit MHz dB dB dB dB dB dB dB dB dB dB Insertion Loss 0.55 0.7 0.85 1.05 39 31 35 28 20 16 -82 -89 -74 -68 2 0.65 0.8 1.0 1.2 Isolation Return Loss 2nd Harmonic1,2 3rd Harmonic1,2 Switching time Notes: -78 -82 -69 -65 3 dBc dBc dBc dBc s 1. Measured in Pulsed Wave Mode. 2. Assumes RF input duty cycle of 50% and 4620 s, measured per 3GPP TS 45.005 Table 2. Pin Descriptions Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 Note: Pin Name RX13 GND RX23 V1 V2 VDD GND TX2 3 Figure 3. Pin Configuration (Ball-Side Up) Description N/C TX1 10 11 ANT 12 1 RX1 RF I/O - RX1 Ground RF I/O - RX2 Switch control input, CMOS logic level Switch control input, CMOS logic level Supply Ground RF I/O - TX2 Ground RF I/O - TX1 No Connect - Pin to be connected to an electrically isolated low capacitance pad RF Common - Antenna Input GND 9 PE4261 Die 2 GND TX2 8 3 RX2 GND TX13 N/C ANT3 GND 7 6 VDD 5 V2 4 V1 3. Blocking capacitors needed only when non-zero DC voltage present. (c)2005-2006 Peregrine Semiconductor Corp. All rights reserved. Page 2 of 4 Document No. 70-0188-02 UltraCMOSTM RFIC Solutions NDA required for full version: Contact sales@psemi.com PE4261 Product Specification Table 3. Absolute Maximum Ratings Symbol VDD VI TST TOP PIN RX input power (50 ) TX input power (VSWR = (:1)5,6 824-915 MHz TX input power (VSWR = (:1)5,6 1710-1910 MHz ESD Voltage (HBM, MIL_STD 883 Method 3015.7) ESD Voltage (MM, JEDEC, JESD22-A114-B) ESD Voltage (CDM, JEDEC, JESD22-A114-B) ESD Voltage (IEC 61000-4-2, ANT port) Note: +23 +35 dBm +33 1500 100 1500 2000 V V V V Parameter/Conditions Power supply voltage Voltage on any input Storage temperature range Operating temperature range TX input power (50 ) Min -0.3 -0.3 -65 -40 Max 4.0 VDD+ 0.3 +150 +85 +38 dBm Units V V C C Table 4. DC Electrical Specifications Parameter VDD Power Supply Voltage IDD Power Supply Current (VDD = 2.6 V) Control Voltage High Control Voltage Low 0.7x V DD 0.3x VDD Min 2.4 Typ 2.6 11 Max 2.8 25 Units V A V V Table 5. Truth Table Path ANT - RX1 ANT - RX2 ANT - TX1 ANT - TX2 PIN (:1) V2 0 0 1 1 V1 0 1 0 1 VESD4 Electrostatic Discharge (ESD) Precautions When handling this UltraCMOSTM device, observe the same precautions that you would use with other ESD-sensitive devices. Although this device contains circuitry to protect it from damage due to ESD, precautions should be taken to avoid exceeding the specified rating. 4. ANT port rated higher per Application note, see page 10. 5. Assumes RF input duty cycle of 50% and 4620 s. 6. VDD within operating range specified in Table 4. Absolute Maximum Ratings are those values listed in the above table. Exceeding these values may cause permanent device damage. Functional operation should be restricted to the limits in the DC Electrical Specifications table. Exposure to absolute maximum ratings for extended periods may affect device reliability. Table 6. Ordering Information Order Code PE4261-93 PE4261-96 PE4261-10 Die ID C9804_3 C9804_3 C9804_3 Description PE4261-DIE-D PE4261-DIE-255G PE4261-DIE-1H Latch-Up Avoidance Unlike conventional CMOS devices, UltraCMOSTM devices are immune to latch-up. Package Film Frame Waffle Pack Evaluation Kit Shipping Method Wafer (Gross Die / Wafer Quantity) 255 Dice / Waffle Pack 1 / Box Document No. 70-0188-02 www.psemi.com NDA required for full version: Contact sales@psemi.com (c)2005-2006 Peregrine Semiconductor Corp. All rights reserved. Page 3 of 4 PE4261 Product Specification Sales Offices The Americas Peregrine Semiconductor Corporation 9450 Carroll Park Drive San Diego, CA 92121 Tel: 858-731-9400 Fax: 858-731-9499 North Asia Pacific Peregrine Semiconductor K.K. Teikoku Hotel Tower 10B-6 1-1-1 Uchisaiwai-cho, Chiyoda-ku Tokyo 100-0011 Japan Tel: +81-3-3502-5211 Fax: +81-3-3502-5213 Europe Peregrine Semiconductor Europe Batiment Maine 13-15 rue des Quatre Vents F-92380 Garches, France Tel: +33-1-47-41-91-73 Fax : +33-1-47-41-91-73 Peregrine Semiconductor, Korea #B-2402, Kolon Tripolis, #210 Geumgok-dong, Bundang-gu, Seongnam-si Gyeonggi-do, 463-480 S. Korea Tel: +82-31-728-4300 Fax: +82-31-728-4305 South Asia Pacific Peregrine Semiconductor, China Shanghai, 200040, P.R. China Tel: +86-21-5836-8276 Fax: +86-21-5836-7652 Space and Defense Products Americas: Tel: 858-731-9453 Europe, Asia Pacific: 180 Rue Jean de Guiramand 13852 Aix-En-Provence Cedex 3, France Tel: +33(0) 4 4239 3361 Fax: +33(0) 4 4239 7227 For a list of representatives in your area, please refer to our Web site at: www.psemi.com Data Sheet Identification Advance Information The product is in a formative or design stage. The data sheet contains design target specifications for product development. Specifications and features may change in any manner without notice. The information in this data sheet is believed to be reliable. However, Peregrine assumes no liability for the use of this information. Use shall be entirely at the user's own risk. No patent rights or licenses to any circuits described in this data sheet are implied or granted to any third party. Peregrine's products are not designed or intended for use in devices or systems intended for surgical implant, or in other applications intended to support or sustain life, or in any application in which the failure of the Peregrine product could create a situation in which personal injury or death might occur. Peregrine assumes no liability for damages, including consequential or incidental damages, arising out of the use of its products in such applications. The Peregrine name, logo, and UTSi are registered trademarks and UltraCMOS and HaRP are trademarks of Peregrine Semiconductor Corp. Preliminary Specification The data sheet contains preliminary data. Additional data may be added at a later date. Peregrine reserves the right to change specifications at any time without notice in order to supply the best possible product. Product Specification The data sheet contains final data. In the event Peregrine decides to change the specifications, Peregrine will notify customers of the intended changes by issuing a DCN (Document Change Notice). (c)2005-2006 Peregrine Semiconductor Corp. All rights reserved. Page 4 of 4 Document No. 70-0188-02 UltraCMOSTM RFIC Solutions NDA required for full version: Contact sales@psemi.com |
Price & Availability of PE4261-96
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |