|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
FXL4T245 Low Voltage Dual Supply 4-Bit Signal Translator with Configurable Voltage Supplies and Signal Levels and 3-STATE Outputs April 2004 Revised June 2004 FXL4T245 Low Voltage Dual Supply 4-Bit Signal Translator with Configurable Voltage Supplies and Signal Levels and 3-STATE Outputs General Description The FXL4T245 is a configurable dual-voltage-supply translator designed for bi-directional voltage translation of signals between two voltage levels. The device allows translation between voltages as high as 3.6V to as low as 1.1V. The A Port tracks the VCCA level, and the B Port tracks the VCCB level. Both ports are designed to accept supply voltage levels from 1.1V to 3.6V. This allows for bidirectional voltage translation over a variety of voltage levels: 1.2V, 1.5V, 1.8V, 2.5V, and 3.3V. The device remains in 3-STATE until both VCCs reach active levels allowing either VCC to be powered-up first. The device also contains power down control circuits that place the device in 3-STATE if either VCC is removed. The Transmit/Receive (T/R) input determines the direction of data flow through the device. The OE input, when HIGH, disables both the A and B Ports by placing them in 3-STATE condition. The FXL4T245 is designed so that the control pins (T/R and OE) are supplied by VCCA. Features s Bi-directional interface between any 2 levels from 1.1V to 3.6V s Fully configurable, inputs track VCC level s Non-preferential power-up sequencing; either VCC may be powered-up first s No power-up sequencing required s Outputs remain in 3-STATE until active VCC level is reached s Outputs switch to 3-STATE if either VCC is at GND s Power-off protection s Control inputs (T/R, OE) levels are referenced to VCCA voltage s Packaged in 14-terminal DQFN (2.5mm x 3.0mm) package s ESD protection exceeds: * 4kV HBM ESD (per JESD22-A114 & Mil Std 883e 3015.7) * 8kV HBM I/O to GND ESD (per JESD22-A114 & Mil Std 883e 3015.7) * 1kV CDM ESD (per ESD STM 5.3) * 200V MM ESD (per JESD22-A115 & ESD STM5.2) Ordering Code: Order Number FXL4T245BQX Package Number MLP014A Package Description 14-Terminal Depopulated Quad Very-Thin Flat Pack No Leads (DQFN), JEDEC MO-241, 2.5 x 3.0mm (c) 2004 Fairchild Semiconductor Corporation DS500891 www.fairchildsemi.com FXL4T245 Terminal Descriptions Terminal Names OE T/R An Bn VCCA VCCB GND Description Truth Table Inputs OE T/R L H Bus B Data to Bus A Bus A Data to Bus B Outputs Output Enable Input Transmit/Receive Input Side A Inputs or 3-STATE Outputs Side B Inputs or 3-STATE Outputs Side A Power Supply Side B Power Supply Ground L L H = HIGH Voltage Level L = LOW Voltage Level X = Don't Care Connection Diagram Terminal Assignments for DQFN Terminal Assignment Terminal Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Terminal Name VCCA A0 A1 A2 A3 T/R GND GND OE B3 B2 B1 B0 VCCB (Top View) Power-Up/Power-Down Sequencing FXL translators offer an advantage in that either VCC may be powered up first. This benefit derives from the chip design. When either VCC is at 0 volts, outputs are in a HIGH-Impedance state. The control inputs (T/R and OE) are designed to track the VCCA supply. A pull-up resistor tying OE to VCCA should be used to ensure that bus contention, excessive currents, or oscillations do not occur during power-up/power-down. The size of the pull-up resistor is based upon the current-sinking capability of the OE driver. The recommended power-up sequence is the following: 1. Apply power to either VCC. 2. Apply power to the T/R input (Logic HIGH for A-to-B operation; Logic LOW for B-to-A operation) and to the respective data inputs (A Port or B Port). This may occur at the same time as Step 1. 3. Apply power to other VCC. 4. Drive the OE input LOW to enable the device. The recommended power-down sequence is the following: 1. Drive OE input HIGH to disable the device. 2. Remove power from either VCC. 3. Remove power from other VCC. www.fairchildsemi.com 2 FXL4T245 Absolute Maximum Ratings(Note 1) Supply Voltage VCCA VCCB DC Input Voltage (VI) I/O Port A I/O Port B Control Inputs (T/R, OE) Output Voltage (VO) (Note 2) Outputs 3-STATE Outputs Active (An) Outputs Active (Bn) DC Input Diode Current (IIK) VI < 0V DC Output Diode Current (IOK) VO < 0V VO > VCC DC Output Source/Sink Current (IOH/IOL) DC VCC or Ground Current per Supply Pin (ICC) Storage Temperature Range (TSTG) Recommended Operating Conditions (Note 3) Power Supply Operating (VCCA or VCCB) Input Voltage Port A 0.0V to 3.6V 0.0V to 3.6V 0.0V to VCCA Port B Control Inputs (T/R, OE) Output Current in IOH/IOL VCC 3.0V to 3.6V 2.3V to 2.7V 1.65V to 1.95V 1.4V to 1.65V 1.1V to 1.4V Free Air Operating Temperature (TA) Minimum Input Edge Rate (V/t) VCCA/B = 1.1V to 3.6V 10 ns/V 1.1V to 3.6V -0.5V to +4.6V -0.5V to +4.6V -0.5V to +4.6V -0.5V to +4.6V -0.5V to +4.6V -0.5V to +4.6V -0.5V to VCCA + 0.5V -0.5V to VCCB + 0.5V -50 mA -50 mA +50 mA -50 mA / +50 mA 100 mA -65C to +150C 24 mA 18 mA 6 mA 2 mA 0.5 mA -40C to +85C Note 1: The "Absolute Maximum Ratings" are those values beyond which the safety of the device cannot be guaranteed. The device should not be operated at these limits. The parametric values defined in the Electrical Characteristics tables are not guaranteed at the absolute maximum ratings. The "Recommended Operating Conditions" table will define the conditions for actual device operation. Note 2: IO Absolute Maximum Rating must be observed. Note 3: All unused inputs must be held at VCCI or GND. DC Electrical Characteristics Symbol VIH (Note 4) Parameter High Level Input Voltage Conditions Data Inputs An, Bn VCCI (V) 2.7 - 3.6 2.3 - 2.7 1.65 - 2.3 1.4 - 1.65 1.1 - 1.4 Control Pins/OE, T/R (Referenced to VCCA) 2.7 - 3.6 2.3 - 2.7 1.65 - 2.3 1.4 - 1.65 1.1 - 1.4 VIL (Note 4) Low Level Input Voltage Data Inputs An, Bn 2.7 - 3.6 2.3 - 2.7 1.65 - 2.3 1.4 - 1.65 1.1 - 1.4 Control Pins/OE, T/R (Referenced to VCCA) 2.7 - 3.6 2.3 - 2.7 1.65 - 2.3 1.4 - 1.65 1.1 - 1.4 1.1 - 3.6 1.1 - 3.6 1.1 - 3.6 1.1 - 3.6 VCCO (V) 2.0 1.6 0.65 x VCCI 0.65 x VCCI 0.9 x VCCI 2.0 1.6 0.65 x VCCA 0.65 x VCCA 0.9 x VCCA 0.8 0.7 0.35 x VCCI 0.35 x VCCI 0.1 x VCCI 0.8 0.7 0.35 x VCCA 0.35 x VCCA 0.1 x VCCA V V Min Max Units 3 www.fairchildsemi.com FXL4T245 DC Electrical Characteristics Symbol VOH (Note 5) Parameter High Level Output Voltage (Continued) Conditions VCCA (V) 1.1 - 3.6 2.7 3.0 3.0 2.3 2.3 2.3 1.65 1.4 1.1 1.1 - 3.6 2.7 3.0 3.0 2.3 2.3 1.65 1.4 1.1 1.1 - 3.6 0 3.6 3.6 0 3.6 1.1 - 3.6 1.1 - 3.6 0 1.1 - 3.6 1.1 - 3.6 0 3.6 VCCB (V) 1.1 - 3.6 2.7 3.0 3.0 2.3 2.3 2.3 1.65 1.4 1.1 1.1- 3.6 2.7 3.0 3.0 2.3 2.3 1.65 1.4 1.1 3.6 3.6 0 3.6 3.6 0 1.1 - 3.6 1.1 - 3.6 1.1 - 3.6 0 0 1.1 - 3.6 3.6 VCC0 - 0.2 2.2 2.4 2.2 2.0 1.8 1.7 1.25 1.05 0.75 x VCC0 0.2 0.4 0.4 0.55 0.4 0.6 0.3 0.35 0.3 x VCC0 1.0 10.0 10.0 10.0 +10.0 +10.0 20.0 20.0 -10.0 10.0 -10.0 10.0 500 A A A A A A A A A A V V Min Max Units IOH = -100 A IOH = -12 mA IOH = -18 mA IOH = -24 mA IOH = -6 mA IOH = -12 mA IOH = -18 mA IOH = -6 mA IOH = -2 mA IOH = -0.5 mA VOL (Note 5) Low Level Output Voltage IOL = 100A IOL = 12 mA IOL = 18 mA IOL = 24 mA IOL =12 mA IOL = 18 mA IOL = 6 mA IOL = 2 mA IOL = 0.5 mA II IOFF Input Leakage Current. Control Pins VI = V CCA or GND Power Off Leakage Current An, VI or VO = 0V to 3.6V Bn, VI or VO = 0V to 3.6V OE = VIH OE = Don't Care OE = Don't Care IOZ (Note 6) 3-STATE Output Leakage 0 V O 3.6V VI = VIH or VIL An, Bn Bn, An, ICCA/B (Note 7) Quiescent Supply Current ICCZ (Note 7) ICCA ICCB ICCA/B Quiescent Supply Current Quiescent Supply Current Quiescent Supply Current Increase in ICC per Input; Other Inputs at VCC or GND VI = V CCI or GND; IO = 0 VI = V CCI or GND; IO = 0 VI = V CCA or GND; IO = 0 VI = V CCA or GND; IO = 0 VI = V CCB or GND; IO = 0 VI = V CCB or GND; IO = 0 VIH = 3.0 Note 4: VCCI = the VCC associated with the data input under test. Note 5: VCCO = the VCC associated with the output under test. Note 6: Don't Care = Any valid logic level. Note 7: Reflects current per supply, VCCA or VCCB. www.fairchildsemi.com 4 FXL4T245 AC Electrical Characteristics VCCA = 3.0V to 3.6V TA = -40C to +85C Symbol Parameter VCCB = 3.0V to 3.6V Min tPLH, tPHL Propagation Delay A to B Propagation Delay B to A tPZH, tPZL Output Enable OE to B Output Enable OE to A tPHZ, tPLZ Output Disable OE to B Output Disable OE to A 0.2 0.2 0.5 0.5 0.2 0.2 Max 3.5 3.5 4.0 4.0 3.8 3.7 VCCB = 2.3V to 2.7V Min 0.3 0.2 0.7 0.5 0.2 0.2 Max 3.9 3.8 4.4 4.0 4.0 3.7 VCCB = 1.65V to 1.95V Min 0.5 0.3 1.0 0.5 0.7 0.2 Max 5.4 4.0 5.9 4.0 4.8 3.7 VCCB = 1.4V to 1.6V Min 0.6 0.5 1.0 0.5 1.5 0.2 Max 6.8 4.3 6.4 4.0 6.2 3.7 VCCB = 1.1V to 1.3V Min 1.4 0.8 1.5 0.5 2.0 0.2 Max 22.0 13.0 17.0 ns 4.0 17.0 ns 3.7 ns Units AC Electrical Characteristics VCCA = 2.3V to 2.7V TA = -40C to +85C Symbol Parameter VCCB = 3.0V to 3.6V Min tPLH, tPHL Propagation Delay A to B Propagation Delay B to A tPZH, tPZL Output Enable OE to B Output Enable OE to A tPHZ, tPLZ Output Disable OE to B Output Disable OE to A 0.2 0.3 0.6 0.6 0.2 0.2 Max 3.8 3.9 4.2 4.5 4.1 4.0 VCCB = 2.3V to 2.7V Min 0.4 0.4 0.8 0.6 0.2 0.2 Max 4.2 4.2 4.6 4.5 4.3 4.0 VCCB = 1.65V to 1.95V Min 0.5 0.5 1.0 0.6 0.7 0.2 Max 5.6 4.5 6.0 4.5 4.8 4.0 VCCB = 1.4V to 1.6V Min 0.8 0.5 1.0 0.6 1.5 0.2 Max 6.9 4.8 6.8 4.5 6.7 4.0 VCCB = 1.1V to 1.3V Min 1.4 1.0 1.5 0.6 2.0 0.2 Max 22.0 7.0 17.0 ns 4.5 17.0 ns 4.0 ns Units AC Electrical Characteristics VCCA = 1.65V to 1.95V TA = -40C to +85C Symbol Parameter VCCB = 3.0V to 3.6V Min tPLH, tPHL Propagation Delay A to B Propagation Delay B to A tPZH, tPZL Output Enable OE to B Output Enable OE to A tPHZ, tPLZ Output Disable OE to B Output Disable OE to A 0.3 0.5 0.6 1.0 0.2 0.5 Max 4.0 5.4 5.2 6.7 5.1 5.0 VCCB = 2.3V to 2.7V Min 0.5 0.5 0.8 1.0 0.2 0.5 Max 4.5 5.6 5.4 6.7 5.2 5.0 VCCB = 1.65V to 1.95V Min 0.8 0.8 1.2 1.0 0.8 0.5 Max 5.7 5.7 6.9 6.7 5.2 5.0 VCCB = 1.4V to 1.6V Min 0.9 1.0 1.2 1.0 1.5 0.5 Max 7.1 6.0 7.2 6.7 7.0 5.0 VCCB = 1.1V to 1.3V Min 1.5 1.2 1.5 1.0 2.0 0.5 Max 22.0 8.0 18.0 ns 6.7 17.0 ns 5.0 ns Units AC Electrical Characteristics VCCA = 1.4V to 1.6V TA = -40C to +85C Symbol Parameter VCCB = 3.0V to 3.6V Min tPLH, tPHL Propagation Delay A to B Propagation Delay B to A tPZH, tPZL Output Enable OE to B Output Enable OE to A tPHZ, tPLZ Output Disable OE to B Output Disable OE to A 0.5 0.6 1.1 1.0 0.4 1.0 Max 4.3 6.8 7.5 7.5 6.1 6.0 VCCB = 2.3V to 2.7V Min 0.5 0.8 1.1 1.0 0.4 1.0 Max 4.8 6.9 7.6 7.5 6.2 6.0 VCCB = 1.65V to 1.95V Min 1.0 0.9 1.3 1.0 0.9 1.0 Max 6.0 7.1 7.7 7.5 6.2 6.0 VCCB = 1.4V to 1.6V Min 1.0 1.0 1.4 1.0 1.5 1.0 Max 7.3 7.3 7.9 7.5 7.5 6.0 VCCB = 1.1V to 1.3V Min 1.5 1.3 2.0 1.0 2.0 1.0 Max 22.0 9.5 20.0 ns 7.5 18.0 ns 6.0 ns Units 5 www.fairchildsemi.com FXL4T245 AC Electrical Characteristics VCCA = 1.1V to 1.3V TA = -40C to +85C Symbol Parameter VCCB = 3.0V to 3.6V Min tPLH, tPHL Propagation Delay A to B Propagation Delay B to A tPZH, tPZL Output Enable OE to B Output Enable OE to A tPHZ, tPLZ Output Disable OE to B Output Disable OE to A 0.8 1.4 1.0 2.0 1.0 2.0 Max 13.0 22.0 12.0 22.0 15.0 15.0 VCCB = 2.3V to 2.7V Min 1.0 1.4 1.0 2.0 0.7 2.0 Max 7.0 22.0 9.0 22.0 7.0 12.0 VCCB = 1.65V to 1.95V Min 1.2 1.5 2.0 2.0 1.0 2.0 Max 8.0 22.0 10.0 22.0 8.0 12.0 VCCB = 1.4V to 1.6V Min 1.3 1.5 2.0 2.0 2.0 2.0 Max 9.5 22.0 11.0 22.0 10.0 12.0 VCCB = 1.1V to 1.3V Min 2.0 2.0 2.0 2.0 2.0 2.0 Max 24.0 24.0 24.0 ns 22.0 20.0 ns 12.0 ns Units Capacitance Symbol CIN CI/O CPD Parameter Input Capacitance Control Pins (OE, T/R) Input/Output Capacitance An, Bn Ports Power Dissipation Capacitance Conditions VCCA = VCCB = 3.3V, VI = 0V or VCCA/B VCCA = VCCB = 3.3V, VI = 0V or VCCA/B VCCA = VCCB = 3.3V, VI = 0V or VCC, F = 10 MHz TA = +25C Typical 4.0 5.0 20.0 Units pF pF pF www.fairchildsemi.com 6 FXL4T245 AC Loading and Waveforms TEST tPLH, tPHL tPLZ, tPZL tPHZ, tPZH SWITCH OPEN VCCO x 2 at VCCO = 3.3 0.3V, 2.5V 0.2V, 1.8V 0.15V, 1.5V 0.1V, 1.2V 0.1V GND FIGURE 1. AC Test Circuit AC Load Table VCCO 1.2V 0.1V 1.5V 0.1V 1.8V 0.15V 2.5V 0.2V 3.3V 0.3V CL 15 pF 15 pF 15 pF 15 pF 15 pF RL 2 k 2 k 2 k 2 k 2 k Rtr1 2 k 2 k 2 k 2 k 2 k Note: Input tR = tF = 2.0 ns, 10% to 90% Input tR = tF = 2.5ns, 10% to 90%, @ VI = 3.0V to 3.6V only Note: Input tR = tF = 2.0 ns, 10% to 90% Input tR = tF = 2.5ns, 10% to 90%, @ VI = 3.0V to 3.6V only FIGURE 2. Waveform for Inverting and Non-Inverting Functions FIGURE 3. 3-STATE Output Low Enable and Disable Times for Low Voltage Logic Note: Input tR = tF = 2.0 ns, 10% to 90% Input tR = tF = 2.5ns, 10% to 90%, @ VI = 3.0V to 3.6V only FIGURE 4. 3-STATE Output High Enable and Disable Times for Low Voltage Logic Symbol Vmi Vmo VX VY VCC 3.3V 0.3V VCCI/2 VCCO/2 VOH - 0.3V VOL + 0.3V 2.5V 0.2V VCCI/2 VCCO/2 VOH - 0.15V VOL + 0.15V 1.8V 0.15V VCCI/2 VCCO/2 VOH - 0.15V VOL + 0.15V 1.5V 0.1V VCCI/2 VCCO/2 VOH - 0.1V VOL + 01V 1.2V 0.1V VCCI/2 VCCO/2 VOH - 0.1V VOL + 01V Note: For Vmi: VCCI = VCCA for Control Pins T/R and OE, or VCCA/2 7 www.fairchildsemi.com FXL4T245 Tape and Reel Specification Tape Format for DQFN Package Designator BQX Tape Section Leader (Start End) Carrier Trailer (Hub End) TAPE DIMENSIONS inches (millimeters) Number Cavities 125 (typ) 3000 75 (typ) Cavity Status Empty Filled Empty Cover Tape Status Sealed Sealed Sealed REEL DIMENSIONS inches (millimeters) Tape Size 12 mm A 13.0 (330.0) B 0.059 (1.50) C 0.512 (13.00) D 0.795 (20.20) N 2.165 (55.00) W1 0.488 (12.4) W2 0.724 (18.4) www.fairchildsemi.com 8 FXL4T245 Low Voltage Dual Supply 4-Bit Signal Translator with Configurable Voltage Supplies and Signal Levels and 3-STATE Outputs Physical Dimensions inches (millimeters) unless otherwise noted 14-Terminal Depopulated Quad Very-Thin Flat Pack No Leads (DQFN), JEDEC MO-241, 2.5 x 3.0mm Package Number MLP014A Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications. LIFE SUPPORT POLICY FAIRCHILD'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 9 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.fairchildsemi.com www.fairchildsemi.com |
Price & Availability of FXL4T245BQX |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |