View BS05N1NFAA_1220427.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. !Note *Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
*This catalog has only typical specifications. Therefore,thereareno space for detailed specifications. Therefore, please approve our productsheet for product specifications before ordering. product specifications before ordering. This catalog has only typical specifications because you is requested to approve our product specifications or to transact the approval specifications or transact the approval sheet for
S31E4.pdf 04.8.30
Magnetic Pattern Recognition Sensors
Standard Compact Type
BS05C/N Series
Metal cap 8.80.2 Marking 0.8 4
1
1. High sensitivity and excellent gap characteristics 2. Output voltage is independent of scanning speed. 3. Compact size and light weight make them ideal for downsizing. 4. Longer product life is given to BS05C series with a specially hard metal cover. 5. BS05C1HGCA has superior noise immunity against induced noise originating from motors and transformers.
2.50.2 2.50.2 2.50.2 2.50.2
s Features (BS05C Series)
Sensing direction
3-o0.6
3 1 2
11.10.2 8.10.2
12.50.2 62
4.750.2
3.40.2
MR1
MR2
Magnet
BS05C Series
0.2
2
1
3
4 F. G : Frame GND (in mm)
Vin Vout GND F. G
s Applications
1. Bank note validator 2. Magnetic ink document reader 3. Magnetic card reader 4. Magnetic gear detector
s Features (BS05N Series)
1. High sensitivity and excellent gap characteristics 2. Output voltage is independent of scanning speed. 3. Compact size and light weight make them ideal for downsizing. 4. High reliability by sealing structure 5. BS05N1HGAA has superior noise immunity against induced noise originating from motors and transformers. 6. BS05N1NFAA has wider detection width of 6mm.
Sensing direction Marking 0.8 8.80.2
3-o0.6
4
3 1 2
11.150.2 8.10.2
12.50.2 62
5.30.2
3.40.2
MR1
MR2
Magnet
BS05N Series
0.2
2
1
3
4 F. G : Frame GND (in mm)
Vin Vout GND F. G
s Applications
1. Bank note validator 2. Magnetic ink document reader 3. Magnetic card reader 4. Magnetic gear detector
Supply Voltage (V) 5 5 5 5 5 Total Resistance (k ohm) 0.5 to 4 0.5 to 4 0.5 to 4 0.5 to 4 0.6 to 6 Output Voltage (mVrms) 400 min. 235 to 405 400 min. 235 to 405 330 min. Detection Width (mm) 3 3 3 3 6 Resolution (mm) 0.75 0.75 0.75 0.75 0.87 Operating Temperature Range (C) -20 to 60 -20 to 60 -20 to 60 -20 to 60 -20 to 60
Part Number BS05C1HFAA BS05C1HGCA BS05N1HFAA BS05N1HGAA BS05N1NFAA
Test Method Test Method A Test Method A Test Method A Test Method A Test Method B
Cat.No.S31E-41
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. !Note *Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
*This catalog has only typical specifications. Therefore,thereareno space for detailed specifications. Therefore, please approve our productsheet for product specifications before ordering. product specifications before ordering. This catalog has only typical specifications because you is requested to approve our product specifications or to transact the approval specifications or transact the approval sheet for
S31E4.pdf 04.8.30
1
BS05T Series
Sensing direction 0.7 7.0 -0.2 1.2 3-o0.6 r 2.5 e w q 0.1 MR1 MR2 rF*G wVin MR1 qVout MR2 eGND 0.75 MR element Metal Cover
s Features
1. High sensitivity and excellent gap characteristics 2. Output voltage is independent of scanning speed. 3. Compact size and light weight make them ideal for downsizing. 4. Higher in cost performance 5. Superior noise immunity against induced noise originating from motors and transformers.
BS05T Series
+0
A
+0 11.0 -0.2
7.5
45
7.30.3 10.00.1
3
s Applications
1. Bank note validator 2. Magnetic ink document reader
Supply Voltage (V) 5 Total Resistance (k ohm) 1 to 6 Output Voltage (mVrms) 200 to 400
3.0
4.40.5
NOTES : Space between pins is specified on plane A. General tolerance : 0.2 (in mm)
Part Number BS05T1HGNA
Test Method Test Method B
Detection Width (mm) 3
Resolution (mm) 0.75
Operating Temperature Range (C) -20 to 60
s Test Method A
1. Amplifier's gain is set to 1,100 at the frequency of 60 Hz. Fig. 1 shows the detail of amplifier. 2. DUT is set in the test fixture as shown in Fig. 2. 3. AC current of 100mArms is applied to the copper wire. 4. Amplifier's output voltage is read with DMM while DUT is slowly moved along the guide rail.
10F DUT 2 + 7805 + 0.1F 1 10F 1k +22pF + 0.1F GND 4 GAIN=1,100 -15V5% OUTPUT V ~ 1.5M 47F +15V5%
3
Fig. 1 Amplifier for Output Voltage Measurement
1 2 3
100mArms 60Hz 4 DUT Guide Rail DUT Mylar Film 25mm thick Acrylic Board Copper Wire #2UEW 0.1mm dia.
Fig. 2 Test Fixture for Output Voltage Measurement
Continued on the following page.
2
2.5
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. !Note *Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
*This catalog has only typical specifications. Therefore,thereareno space for detailed specifications. Therefore, please approve our productsheet for product specifications before ordering. product specifications before ordering. This catalog has only typical specifications because you is requested to approve our product specifications or to transact the approval specifications or transact the approval sheet for
S31E4.pdf 04.8.30
Continued from the preceding page.
s Test Method B
1. Amplifier's gain is set to 1,100 at the frequency of 60 Hz. Fig. 1 shows the detail of amplifier. 2. DUT is set in the test fixture as shown in Fig. 2. 3. AC current of 100mArms is applied to the copper wire. 4. Amplifier's output voltage is read with DMM while DUT is slowly moved along the guide rail.
10F DUT 2 + 7805 47F + 0.1F 1 + 10F 3 + - 1k + 0.1F GND 4 GAIN=1,100 -15V5% 22pF OUTPUT V ~ 1.5M +15V5%
1
Fig. 1 Amplifier for Output Voltage Measurement
1 2 3
100mArms 60Hz 4 DUT Guide Rail DUT Mylar Film 25mm thick Copper Wire #2UEW 0.1mm dia. Acrylic Board
Fig. 2 Test Fixture for Output Voltage Measurement
3
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. !Note *Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
*This catalog has only typical specifications. Therefore,thereareno space for detailed specifications. Therefore, please approve our productsheet for product specifications before ordering. product specifications before ordering. This catalog has only typical specifications because you is requested to approve our product specifications or to transact the approval specifications or transact the approval sheet for
S31E4.pdf 04.8.30
Magnetic Pattern Recognition Sensors
Wide Sensing Element Type
5.6 Marking 4-o0.6 2.5 150.2 62 Sensing direction Metal Cover (10.8) GND 62 10.10.5 Vin Vout F*G Vin MR1 Vout MR2 GND 5.2
2
s Features
1. Wide MR element covering extensive area allows increased tolerance for scanning and can accept a variety of bank notes. 2. Long product life achieved by an extremely hard metal cover is ideal for use in high speed ATM and bank note counters. 3. High sensitivity and excellent gap characteristics 4. Output voltage is independent of scanning speed. 5. BS05W1KFAB is ideal for use in high-speed process machines such as ATM and bank note counters because an extremely hard metal cover is used.
15
BS05W Series
4 2.5 110.2
112
F*G
Metal Cover F. G : Frame GND General tolerance : 0.3
(in mm)
s Applications
1. Bank note validator 2. Magnetic ink document reader
Supply Voltage (V) 5 5 Total Resistance (k ohm) 1 to 15 1 to 15 Output Voltage (mVp-p) 0.3 to 0.8 0.3 to 0.8 Detection Width (mm) 10 10 Resolution (mm) 0.75 0.75 Operating Temperature Range (C) -20 to 60 -20 to 60
Part Number BS05W1KFAA BS05W1KFAB
Test Method Test Method C Test Method C
s Test Method C
1. Output voltage is measured by using the magnetic pattern card. The magnetic pattern card has the same magnetic density of 1000 letters on 1000 yen bank notes. 2. Drive the magnetic pattern card and record output voltage Vp-p with X-Y recorder.
X-Y recorder Vin Magnetic ink Vout GND DC voltage supply
X axis : 2mm/s 5Vdc0.1V Y axis : 0.1mV/cm (Input filter : ON) DUT Driving speed : 2mm/s
Card Rubber roller Pressure about 98mN P P Vp-p P=15mm
1mm
4
2.5
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. !Note *Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
*This catalog has only typical specifications. Therefore,thereareno space for detailed specifications. Therefore, please approve our productsheet for product specifications before ordering. product specifications before ordering. This catalog has only typical specifications because you is requested to approve our product specifications or to transact the approval specifications or transact the approval sheet for
S31E4.pdf 04.8.30
Magnetic Pattern Recognition Sensors
Multi-channel Type
Sensing direction PPPPPPPP 0.75 2 3 Channelx8, Pitch P=5, Total Pitch Tolerance0.6 0.5 1.5 45 44 30 1 3 M Rna M Rnb Elements 15 (10) 7.5 7.5 Ground Wire 3.5 15 24-o0.6Terminals 1 20.5 8-2.5
s Features
1. High sensitivity and excellent gap characteristics 2. Output voltage is independent of scanning speed. 3. Compact size and light weight make them ideal for downsizing. 4. Simple and quick mounting is possible due to one single holder for multiple MR elements. 5. BS05M1KFCA, BS05M1KGCA have detection width of 60mm, without non-detection area. 6. BS05M1KFBA, BS05M1KFBB have detection width of 130mm, without non-detection area. 7. BS05M1KGCA has superior noise immunity against induced noise originating from motors and transformers.
Ch1Ch2Ch3Ch4Ch5Ch6Ch7Ch8
3232323232323232
General Tolerance : 0.3 (in mm)
1 2 3
3
BS05M1HFAL
1 1 1 1 1 1 1 1
: GND (0V) : V out (n) : V in (+5)
Table for Wiring
CH02
CH12
1. Bank note validator 2. Magnetic ink document reader 3. Magnetic card reader
4.0
s Applications
5.0
CH01
CH03
CH11
CH13
14.0 4~8 0.15 +0.1 18.0 -0.05
0.10
3.5 -0
10 10 13-2.5
13-2.5
FG 10.1 ewq
+1
100.5
CH01 CH02
25.0
90.0 20.0
qew 39-o0.6 4-4.5
8-C2.5 8-C1
BS05M1KFBA
q : Vout (n) Case Material : PPS w : Vin (+5V) Metal Cover : Stainless Steel e : GND (0V) Tolerance 0.3 FG : Frame GND (in mm)
12.5
140.0 p p p=10.0 0.15 Pitch Total Tolerance 0.3
CH02 CH04 CH06 CH08 CH10 CH12
12.5 14.0 4~8 0.15 +0.10 18.0 -0.05 5.0
66.0 CH02 CH04 CH06 8.0 10.0 10.0 10.0 10.0 10.0 (10.0) 15.0
5.0
CH01
CH03
CH05
CH07
CH09
CH11
CH13
MR element 0.10
2-305 1.5
65.0 7.5 30 3.5
3.5 -0.0
10 10
FG 1.00.1 ewq
+0.1
10.00.5 20.0 6-2.5 ewq 6-2.5 1 2.00.5
0.15
CH01
CH03
CH05
FG 2.5
13-2.5
39-o0.6 q e w 13-2.5 q : Vout (n) Case Material : PPS w : Vin (+5V) Metal Cover : Stainless Steel e : GND (0V) Tolerance 0.3 FG : Frame GND (in mm)
BS05M1KFBB
BS05M1KFCA/BS05M1KGCA
w e 18- o0.6Terminals q
Cover : Stainless steel Case : PPS General tolerance : 0.3 (in mm)
Part Number BS05M1HFAL BS05M1KFBA BS05M1KFBB BS05M1KFCA BS05M1KGCA
Supply Voltage (V) 5 5 5 5 5
Total Resistance (k ohm) 0.5 to 6 1 to 5 1 to 5 1 to 6 0.5 to 6
Output Voltage (mVrms) 150 min. 350 min. 350 min. 300 min. 150 min.
Test Method Test Method D Test Method E Test Method E Test Method E Test Method E
Detection Width (mm) 3 x 8ch 10 x 13ch 10 x 13ch 10 x 6ch 10 x 6ch
Resolution (mm) 0.75 0.75 0.75 0.75 0.75
Operating Temperature Range (C) 0 to 50 0 to 50 0 to 50 0 to 50 0 to 50
18.0 27.5 38.0
q : Vout (n) w : Vin (+5V) e : GND (0V) FG : Frame GND n : Channel No.
12.5 7.3 12.5
140.0 p p p=10.0 0.15 Pitch Total Tolerance 0.3
305
5
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. !Note *Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
*This catalog has only typical specifications. Therefore,thereareno space for detailed specifications. Therefore, please approve our productsheet for product specifications before ordering. product specifications before ordering. This catalog has only typical specifications because you is requested to approve our product specifications or to transact the approval specifications or transact the approval sheet for
S31E4.pdf 04.8.30
s Test Method D
1. Amplifier's gain is set to 70dB at the frequency of 500Hz. Fig. 1 shows details of amplifier. 2. DUT is set in the test fixture as shown in Fig. 2. 3. AC current of 100mArms is applied to the copper wire. 4. Amplifier's output voltage is read with DMM while DUT is slowly moved along the guide rail.
Vin=1.5V PC317 OUT IN adj 1000p 330pF 100k 2 0.47F 1 FG GAIN=70dB 1k 10k 10k 4820 + 10k 0.47F 1k 100 100 10k Vn(-8V) 4820 + Vout 560k Vp(+8V) Vin(+5V)
DUT
3
Fig. 1 Amplifier for Output Voltage Measurement
3
AC100mArms 500Hz 2 3 1 DUT Guide Rail DUT Spacer 0.2mm thick Acrylic Board Copper Wire #2UEW 0.1mm dia.
Fig. 2 Test Fixture for Output Voltage Measurement
s Test Method E
1. Amplifier's gain is set to 1,100 at the frequency of 60 Hz. Fig. 1 shows details of amplifier. 2. DUT is set in the test fixture as shown in Fig. 2. 3. AC current of 100mA (rms) is applied to the copper wire. 4. Amplifier's output voltage is read with DMM while DUT is slowly moved along the guide rail.
10 F DUT + - w - q + e +- 10 F
7805
47 F + - 0.1 F
+15V 5%
1.5 M 22pF
1 k - +
OUTPUT V 0.1 F GND
FG GAIN=1100 -15V 5%
Fig. 1 Amplifier for Output Voltage Measurement
AC100mA (rms) 50/60Hz DUT Guide Rail DUT Mylar Film 25m thick Acrylic Board Copper Wire #2UEW 0.1mm dia.
Fig. 2 Test Fixture for Output Voltage Measurement
6
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. !Note *Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
*This catalog has only typical specifications. Therefore,thereareno space for detailed specifications. Therefore, please approve our productsheet for product specifications before ordering. product specifications before ordering. This catalog has only typical specifications because you is requested to approve our product specifications or to transact the approval specifications or transact the approval sheet for
S31E4.pdf 04.8.30
!Caution/Notice
s !Caution (Handling)
1. This sensor generates very strong suction because this product contains a permanent magnet. Be careful not to apply mechanical shock when handling the sensor. 2. Do not place this product near magnetic recording media such as magnetic tapes or floppy disks. Magnetic recording could be damaged. 3. Do not place this product near a person who has an electronic medical device. It is very dangerous and may cause malfunction of an electronic medical device.
3
s Notice (Storage and Operating Condition)
1. Please avoid water, chemical solvent or oil. 2. Please avoid corrosive gas (Chlorine gas, Hydrogen sulfide gas, Ammonia gas, Nitric oxide gas, etc.). 3. Please avoid airborne particles. 4. Please avoid strong vibration or shock. 5. Ambient temperature change should be within 1 deg. C/min.
s Notice (Rating)
1. This product is designed to detect magnetic properties of banknotes. Please contact us when using this product to detect any magnetic properties other than of banknotes. 2. Because this product contains a permanent magnet, magnetic signals in writable magnetic cards, such as train tickets or pre-paid cards could be damaged. Please consult with us before using in such circumstances. 3. BS05M1 series: To avoid unusual wear of the metal cover or jamming of the banknote, around 0.1mm gap between the sensor and the opposite mechanisms such as rollers is recommended to reduce the load on the metal cover. A load of 0N is recommended. 4. BS05N series, BS05C series, BS05W series: Please do not apply excessive force or shock on the sensing side. When adhering the target media on the sensing side, please give the same level of load throughout the sensor surface and the load should be less than 0.49N. When a roller is set over the sensor, it should be cylindrical shape and its diameter greater than the width of the sensor. If the area coming in contact with the sensor is smaller, the surface will be partially worn and lead to trouble. 5. Please mount this product with holder stuck firmly on the PCB in addition to solder terminals.
s Notice (Soldering and Mounting)
1. Excessive force or shock to the product should be avoided, especially to the metal cover. 2. Do not place the product near magnets, moving ferromagnetic materials, parts which generate magnetic fields. 3. Do not place the product near high voltage lines or high current lines. 4. Do not apply excessive force, rotate or bend the terminal. 5. Wiring should be avoided while voltage supply is active. 6. Hand soldering should be applied. Soldering should be done in following conditions: Soldering Temperature: 350+/-10 deg. C less than 3 seconds or 260+/-5 deg. C less than 10 seconds. 7. Flux should be rosin with a chlorine content of no more than 0.2wt%. 8. Flux cleaning should be done by hand brushing. 9. Prevent the flux cleaning solvent from splashing on the product.
7
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. !Note *Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
*This catalog has only typical specifications. Therefore,thereareno space for detailed specifications. Therefore, please approve our productsheet for product specifications before ordering. product specifications before ordering. This catalog has only typical specifications because you is requested to approve our product specifications or to transact the approval specifications or transact the approval sheet for
S31E4.pdf 04.8.30
Reference Data
s Construction
Magnetic pattern recognition sensor consists of a pair of magnetoresistive (MR) elements and a magnet.
Sensing direction MR1 MR2
Magnet
1 Vin
2 Vout
3 GND
4 F-G
3
s Magnetoresistive Effect
A change in the resistance of a ferromagnetic or semiconductive material when it is subjected to magnetic flux is illustrated in the diagram. Murata's sensor uses InSb, which exhibits a very high magnetoresistive effect.
R() 1,000
500
0.3
0.2 S
0.1
0 B(KG)
0.1 N
0.2
0.3
s Principle of Operation
When a material printed with magnetic ink is scanned over the sensor, the magnetic flux applied to MR1 and MR2 changes. Thus, the sensor generates signals as indicated below.
Magnet MR1 MR2 Flux Scanning Magnetic pattern 1 Output voltage [Vout] 3 2 1/2 Vcc MR2 1 GND MR1 Output 2 3 Vcc
s Typical Application
7805 + 10F - Sensor Vin Vout - + GND +- 10F 1k - + 0.1F GND OUTPUT 22pF 1.5M + - 47F 0.1F +15V5%
F. G
-15V5% GAIN = 1,100
8
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. !Note *Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
*This catalog has only typical specifications. Therefore,thereareno space for detailed specifications. Therefore, please approve our productsheet for product specifications before ordering. product specifications before ordering. This catalog has only typical specifications because you is requested to approve our product specifications or to transact the approval specifications or transact the approval sheet for
S31E4.pdf 04.8.30
ISO 9000 Certifications/Part Numbering
Manufacturer's of the products in this catalog have obtained the ISO 9000 quality system certificate.
Plant Kanazawa Murata Mfg. Co., Ltd. Includes Nishikanazawa factory Certified Date Nov. 25,1992 Organization Reliability Center for Electronic Components of Japan Registration No. RCJ-92M-10
o Part Numbering
Magnetic Pattern Recognition Sensors
(Part Number) qProduct ID wType eCharacteristics rIndividual Specification Code
* "(Part Number)" shows only an example which might be different from actual part number. * Any other definitions than "qProduct ID" might have different digit number from actual part number.
BS q
05W w
1KFAB e r
3
9
!Note Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
S31E4.pdf 04.8.30
Note:
1. Export Control For customers outside Japan No muRata products should be used or sold, through any channels, for use in the design, development, production, utilization, maintenance or operation of, or otherwise contribution to (1) any weapons (Weapons of Mass Destruction (nuclear, chemical or biological weapons or missiles) or conventional weapons) or (2) goods or systems specially designed or intended for military end-use or utilization by military end-users. For customers in Japan For products which are controlled items subject to the "Foreign Exchange and Foreign Trade Law" of Japan, the export license specified by the law is required for export.
< <
>
>
2. Please contact our sales representatives or product engineers before using the products in this catalog for the applications listed below, which require especially high reliability for the prevention of defects which might directly damage a third party's life, body or property, or when one of our products is intended for use in applications other than those specified in this catalog. q Aircraft equipment w Aerospace equipment e Undersea equipment r Power plant equipment t Medical equipment y Transportation equipment (vehicles, trains, ships, etc.) u Traffic signal equipment i Disaster prevention / crime prevention equipment o Data-processing equipment !0 Application of similar complexity and/or reliability requirements to the applications listed above 3. Product specifications in this catalog are as of July 2004. They are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. If there are any questions, please contact our sales representatives or product engineers. 4. Please read rating and CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. 5. This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 6. Please note that unless otherwise specified, we shall assume no responsibility whatsoever for any conflict or dispute that may occur in connection with the effect of our and/or a third party's intellectual property rights and other related rights in consideration of your use of our products and/or information described or contained in our catalogs. In this connection, no representation shall be made to the effect that any third parties are authorized to use the rights mentioned above under licenses without our consent. 7. No ozone depleting substances (ODS) under the Montreal Protocol are used in our manufacturing process.
http://www.murata.com/
Head Office 1-10-1, Higashi Kotari, Nagaokakyo-shi, Kyoto 617-8555, Japan Phone: 81-75-951-9111 International Division 3-29-12, Shibuya, Shibuya-ku, Tokyo 150-0002, Japan Phone: 81-3-5469-6123 Fax: 81-3-5469-6155 E-mail: intl@murata.co.jp

▲Up To Search▲

Price & Availability of BS05N1NFAA

	To Download BS05N1NFAA Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .