 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| ASAHI KASEI [AK8850] AK8850 NTSC Digital Video Decoder General Description The AK8850 decodes NTSC composite video, S-Video and Component Video signals (525/625) into digital formats. Digital output conforms to ITU-R BT.601 and ITU-R BT.656* YCrCb specifications. The AK8850 outputs a control signal to generate clocks synchronized with either Horizontal Sync or Vertical Sync signals. Its clock rate is 27 MHz. An encoded VBID Closed Caption signal can be extracted from the video signal and sent to an external pin on the AK8850. Features NTSC-M Composite signal and S-Video signal decoder Component Video decoder for 525 / 625 systems ( Betacam,MII,EBU N10 ) On-chip triple 10-Bit ADCs ( 27 MHz operation ) On-chip Programmable Gain Amp ( PGA ), ranging from 0 dB to 12 dB in 0.1 dB / steps Input-synchronized clock is generated by an external VCXO Sub-Carrier generation by Digital Synthesizer ( DFS ) Auto Color Control ( ACC ) Auto Gain Control ( AGC ) Adaptive 3-line Y-C separation ITU-R BT.656 format output ( 4:2:2 8-Bit parallel output with EAV / SAV ) NTSC Closed Caption signal decoding function VBID Program condition decoding function WSS Program condition decoding function Video Aspect Signal decoding function on Line 16 and Line 279 Sleep function 6-channel Analog inputs I2C Control 3.3 V CMOS 100-Pin LQFP package note: * ITU-R BT.656 spec may not be satisfied, as it is dependent upon input signal quality. Rev.0 1 2002/01 ASAHI KASEI 1. Functional Block Diagram IVCXO CLK CLKINV [AK8850] NSTD LLPF LLPFC FLPF FLPFC IRefR1 CLOCK Module 27MHz Phase Error Timing Contorller & NSIG CLK27MOUT HALFCLKOUT DVALID/VLOCK VSYNC HSYNC FIELD FRAME0 FRAME1/CSYNC LumaProcessing & VCO Controller & Sync-Separatio n & Registers AGC Info. EXTCLP & Closed Caption VBID Extraction Y AIN1 AIN2 AIN3 AIN4 AIN5 AIN6 SYNC1 SYNC2 SYNC3 FBCAP1 FBCAP2 FBCAP3 CLPCAP1 CLPCAP2 VREF 13.5MHz Analog Multiplexer Clamp PGA Sync Separator Composite Y Y/C Separation (2D-3Line or 1D-BPF) Image Ctrl (Brightness, Contrast etc.) U 10-bit ADC 10-bit ADC 10-bit ADC C C /U Decimation Filter ChromaProcessing & V U Output Processing (Level Shifter & Rec.656 formatter etc.) with Buffer D[7:0] V ACC DFS (Chroma PLL) & V Image Ctrl (HUE,Saturation) Microprocessor I/F 1-1. SignalAVDD ( Composite Video signal inVREF IRefR2 Path AVSS VRP VCOM VRN put ) SELA SDA SCL /RESET PD DVDD DVSS Rev.0 2 2002/01 ASAHI KASEI IVCXO CLK CLKINV [AK8850] LLPF LLPFC FLPF FLPFC IRefR1 Sync-Separatio n & NSTD Phase Error CLOCK Module 27MHz Timing Contorller & NSIG CLK27MOUT HALFCLKOUT DVALID/VLOCK VSYNC HSYNC FIELD FRAME0 FRAME1/CSYNC LumaProcessing & VCO Controller & Registers AGC Info. EXTCLP & Closed Caption VBID Extraction Composite AIN1 AIN2 AIN3 AIN4 AIN5 AIN6 SYNC1 SYNC2 SYNC3 FBCAP1 FBCAP2 FBCAP3 CLPCAP1 CLPCAP2 AVDD VREF Composite Y/C Separation (2D-3Line or 1D-BPF) Y Image Ctrl (Brightness, Contrast etc.) Y Analog Multiplexer Clamp PGA Sync Separator 10-bit ADC Composite C Decimation Filter Output Processing (Level Shifter & Rec.656 formatter etc.) with Buffer U D[7:0] ChromaProcessing & ACC DFS 13.5MHz (Chroma PLL) & V Image Ctrl (HUE,Saturation) Microprocessor I/F 1-2. Signal Path ( YC signal input ) AVSS VRP VCOM VRN VREF IRefR2 SELA SDA SCL /RESET PD DVDD DVSS Rev.0 3 2002/01 ASAHI KASEI IVCXO CLK CLKINV [AK8850] LLPF LLPFC FLPF FLPFC IRefR1 Sync-Separatio n & NSTD Phase Error CLOCK Module 27MHz Timing Contorller & NSIG CLK27MOUT HALFCLKOUT DVALID/VLOCK VSYNC HSYNC FIELD FRAME0 FRAME1/CSYNC Y VCO Controller & Registers AGC Info. EXTCLP & Closed Caption VBID Extraction LumaProcessing & Y AIN1 AIN2 AIN3 AIN4 AIN5 AIN6 SYNC1 SYNC2 SYNC3 FBCAP1 FBCAP2 FBCAP3 CLPCAP1 CLPCAP2 VREF 13.5MHz C Y Image Ctrl 10-bit ADC 10-bit ADC (Brightness, Contrast etc.) Y Analog Multiplexer Clamp PGA Sync Separator C C Decimation Filter ChromaProcessing & U Output Processing (Level Shifter & Rec.656 formatter etc.) with Buffer D[7:0] ACC DFS (Chroma PLL) & V Image Ctrl (HUE,Saturation) Microprocessor I/F 1-3. Signal Path ( ComponentVRP VCOM ) AVDD AVSS signal input VRN VREF IRefR2 IVCXO CLK SELA SDA SCL /RESET PD DVDD DVSS CLKINV Rev.0 LLPF FLPFC CLOCK Phase Error 4 2002/01 NSTD NSIG CLK27MOUT HALFCLKOUT Timing Contorller ASAHI KASEI [AK8850] Rev.0 5 2002/01 ASAHI KASEI 2. Pin Assignment [AK8850] VREFOUT CLPCAP1 CLPCAP2 EXTCLP FBCAP1 FBCAP2 FBCAP3 IRefR1 IVCXO FLPF LLPFC VCOM FLPFC IRefR2 AVDD AVDD AVSS DVDD AVSS AVSS AIN1 AVSS SYNC1 AVSS AIN2 AVSS SYNC2 AVSS AIN3 AVSS SYNC3 AVSS AVDD AVSS AVSS AIN4 AVSS AIN5 AVSS AIN6 AVSS TEST PD TEST TEST 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 CLK DVSS LLPF VRP VRN /RESET CLKINV UD9 UD8 UD7 UD6 UD5 DVSS DVDD NSTD NSIG CLK27MOUT DVSS DVDD HALFCLKOUT FRAME0 FRAME1 DVSS DVDD DVALID/VLOCK UD4 UD3 UD2 UD1 UD0 100 1 TEST SCL DVSS FIELD SELA VSYNC DVDD SDA D6 DVDD D4 DVDD D2 DVDD HSYNC Rev.0 6 D0 DVDD DVSS DVSS DVSS DVSS D7 D5 D3 D1 2002/01 ASAHI KASEI 3. Pin Functional Description Pin Number 2 3 4 6 7 8 11 12 15 16 19 20 23 24 31 34 35 36 39 40 41 49 50 52 54 58 59 60 61 62 63 64 65 66 67 68 69 Identification SCL SDA SELA FIELD HSYNC VSYNC D7 (MSB) D6 D5 D4 D3 D2 D1 D0 (LSB) DVALID/VLOCK FRAME1/CSYNC FRAME0 HALFCLKOUT CLK27MOUT NSIG NSTD CLKINV /RESET CLK EXTCLP LLPF LLPFC FLPF FLPFC VREFOUT IVCXO IRefR1 IRefR2 VCOM VRN VRP FBCAP3 I/O [AK8850] Description I2C bus Clock I2C bus Data (Open Collector ) I2C bus address selector FIELD Identify Low EVEN High ODD HSYNC Timing output pin VSYNC Timing output pin. (It is possible to output V_Blank Signal (VD) by setting a register) Decoded data output pin (MSB) I I/O I O O O O O O O O O O O O O O O O O O I I I I/O O O O O O O O O O O O O Decoded data output pin Decoded data output pin (LSB) Active Video Timing signal (720 Pixel) It can also output VLOCK status by setting a register. When a standard signal is input, a color frame signal is output. When a non-standard signal input, this pin outputs a timing signal that is toggled every 525/625 lines. FRAME1 pin can output the CYSNC signal by setting a register. When Rec.656 data is output, this signal identifies the signal as Y or C. (This rate is about 13.5MHz) Output Timing of output data (About 27MHz) When No-signal is input this pin goes High. When Non-standard signal is input, this pin goes High. This pin decides the polarization of CLK27MOUT. Reset Signal input pin. (Low Active) After Power up or power down mode, Reset signal should be Low at least 10msec. Input 27MHz Clock. External Clamp timing input pin. Connect Loop Filter for Line Lock clock. Connect Capacitors for Line Lock clock. Connect Loop Filter for Frame Lock clock. Connect Capacitors for Frame Lock clock. Internal Voltage Reference output pin. Terminate with 0.1uF or larger capacitor between AVSS. Control voltage output pin for the external VCXO. Connect via a resistor to AVSS. Terminate with 13k resistor (0.1% accuracy) to AVSS. This Register sets the reference current for the PLL Block. Terminate with 4.7k Register (0.1% accuracy) between AVSS. This Register sets the internal reference current. Internal common voltage for ADC output pin. Terminate with 0.1uF or larger capacitor between AVSS. Internal negative voltage for ADC output pin. Terminate with 0.1uF or larger capacitor between AVSS. Internal positive voltage for ADC output pin. Terminate with 0.1uF or larger capacitor between AVSS. Terminate using a 0.033uF capacitor between AVSS. (for Clamp Level) Rev.0 7 2002/01 ASAHI KASEI [AK8850] 70 71 72 73 76 80 84 91 93 95 78 82 86 98 56,75,88 55,57,74, 77,79,81, 83,85,87, 89,90,92, 94,96,96 9,13,17, 21,25,32, 37,42,53 5,10,14, 18, 2,33, 38,43,51 26,27,28, 29,30,44, 45,46,47, 48 1,44,45, 46,47,48, 97,99, 100 FBCAP2 FBCAP1 CLPCAP2 CLPCAP1 AIN1 AIN2 AIN3 AIN4 AIN5 AIN6 SYNC1 SYNC2 SYNC3 PD AVDD AVSS O O O O I I I I I I I I I I P G Terminate 0.033uF capacitor between AVSS. (for Clamp Level) Terminate 0.033uF capacitor between AVSS. (for Clamp Level) Terminate 0.1uF capacitor between AVSS. (for Clamp) Terminate 0.1uF capacitor between AVSS. (for Clamp) Analog video signal input pin. The signal should be input through a 0.1uF capacitor with -6dB Gain. Analog video signal input pin for the internal clamp pulse generator. This signal should be input through a 0.1uF capacitor with 0dB Gain. Power Down Control Pin. When this pin becomes High, the AK8850 enters a power down state. When returning from power down mode, AK8850 requires reset sequence. Analog power supply (3.3V) pin. Analog Ground pin. DVDD DVSS P G Digital power supply (3.3V) pin. Digital Ground pin. UD[9:0] I/O These pins are for test purpose. These pins should be NC. TEST I These pins are for test purpose. Connect to the DVSS. Rev.0 8 2002/01 ASAHI KASEI 4. Electrical Specifications 4-1. Absolute Maximum Ratings Item Min. Max Supply Voltage VDD 0.3 4.5 DVDD, AVDD Input Pin Voltage (Vin) 0.3 VDD + 0.3 Input Pin Current (Iin) 10 10 Storage Temperature 40 125 note) each ground pin ( DVSS,AVSS) is equal to 0 V (voltage reference ). Unit V V mA [AK8850] 4-2. Recommended Operating Conditions Item Min. Typ. Max. Unit Supply Voltage 3.0 3.3 3.6 V AVDD 3.0 3.3 3.6 V DVDD Operating Temperature 10 85** note) * each ground pin ( DVSS,AVSS) is equal to 0 V (voltage reference ). ** Assumes mounting on a 4-layer PCB >100mm x 100mm x 1.6mm with wiring density greater than 60%. 4-3DC Characteristics ( DVDD=AVDD=3.0 ~ 3.6 V at room temperature ) Item Symbol Min. Typ. Max. Digital Input High Voltage VIH 0.7VDD Digital Input Low Voltage VIL 0.3VDD Digital Input Leak Current IIL 10 Digital Output High Voltage VOH 2.4 Digital Output High Voltage VOL 0.4 I2C Input High Voltage VIHC 0.7VDD I2C (SDA, SCL) I2C Input Low Voltage I2C (SDA, SCL) I2C (SDA) L VILC VOLC Symbol Load Min. 15 Typ. 0.3VDD 0.4 Max. 40 Unit V V uA V V V V V Unit pF IOLC = 3mA Condition Condition IOH = 400uA IOL = 1.2mA 4-4. AC Characteristics Item Digital Maximum Capacitance Rev.0 9 2002/01 ASAHI KASEI 4-5. Analog Characteristics and Power Dissipation Selector and Clamp (AVDD=3.3V, Room Temperature) Item Symbol Min. Maximum Input Range VIMX 1.20 (AIN1 AIN6) Composite, Luminance VYCP Signal Clamp Level C/U/V Signal VCCP Clamp Level Clamp Current CLPI Isolation between ADC PGA (AVDD=3.3V, Room Temperature) Item Symbol Min.Gain GMN Max Gain GMX Gain Step GST Relative Gain accuracy ERP ADC (AVDD=3.3V, Room Temperature) Item Symbol Resolution RES Operating Clock Frequency FS Integral Non Linearity INL Differential Non Linearity DNL S/N S/(N+D) SN SND Typ. 1.28 0.70 1.34 70 -60 Max. Unit VPP V V uA dB Max. Unit dB dB dB LSB Unit bits MHz LSB LSB dB dB 5.5MHz Condition PGA Gain 0dB [AK8850] Min. Typ. 0 12 0.094 1 Typ. 27 2.0 0.8 54 51 Condition Min. Max 10 4.0 2.0 Condition fs=27MHz fs=27MHz fin=1MHz Ain= 1dB fs=27MHz fin=1MHz Ain= 1dB fs=27MHz Condition 3ch operating 25pFLoad, Color bar input Mode 1: Set by Register Power Consumption (DVDD=AVDD=3.3V, Room Temperature) Item Symbol Min. Typ. Compensation Current 216 (Active) 71 Digital + Analog 145 Analog Digital Power Down Current Mode 1 58 Digital + Analog 22 Analog 36 Digital Mode 2 0.01 Digital + Analog 0.01 Analog 0.01 Digital Max 280 Unit mA mA mA 75 mA mA mA mA mA mA Mode 2: Set by PD pin *It requires several second from Mode 2 power down mode to Active mode. 0.2 Rev.0 10 2002/01 ASAHI KASEI 4-6. AC Timing ( DVDD=3.0 ~ 3.6 V at 25 deg. C ) 4-6-1 Clock Input fSYSCLK tCLKL tCLKH VIH 1/2 Level of VHI and VIL VIL [AK8850] item CLK CLK pulse width (High) CLK pulse width (Low) Stability of Clock Symbol fSYSCLK tCLKH tCLKL Min. 15 15 Typ. 27 Max 100 Unit MHz nsec nsec ppm 4-6-2 Output Data Timing ( D7 ~ D0 ) 4-6-2-1 CLKINVpin = L VIH CLK27MOUT VIL VIH HALFCLKOUT tODL1 tOHD1 VIH VIL VIL D7:0] Cb/Cr Y Item Output Data Delay Time Output Data Hold Time Symbol tODL1 tOHD1 Min. 3.0 Typ. Max. 25.0 Unit nsec nsec Note CL 25pF Rev.0 11 2002/01 ASAHI KASEI 4-6-2-2 CLKINVpin = H [AK8850] VIH CLK27MOUT tDHCLK VIL VIH HALFCLKOUT tODL2 tOHD2 VIH VIL VIL D7:0] Cb/Cr Y Item Output Data Delay Time Output Data Hold Time Symbol tODL2 tOHD2 Min. 3.0 Typ. Max. 25.0 Unit nsec nsec Note CL 25pF 4-6-3 Output Data Timing ( DVALID/VSYNC/HSYNC/FIELD/FRAME0/FRAME1 ) 4-6-3-1 CLKINVpin = L Output Control Register DVALID=L VSYNC=L HSYNC =L FIELD=L FRAME=L VIH CLK27MOUT tOHD3 DVALID VSYNC/VD HSYNC FIELD FRAME Output Control Register DVALID=H VSYNC=H HSYNC =H FIELD=H FRAME=H VIH CLK27MOUT tOHD3 DVALID VSYNC/VD HSYNC FIELD FRAME VIH VIL Item Output Data Hold Time Symbol tOHD3 Min. 3.0 Typ. Max. Unit nsec Note CL 25pF Rev.0 12 2002/01 ASAHI KASEI 4-6-3-2 CLKINVpin = H Output Control Register DVALID=L VSYNC=L HSYNC =L FIELD=L FRAME=L [AK8850] CLK27MOUT tOHD4 VIL DVALID VSYNC/VD HSYNC FIELD FRAME VIH Output Control Register DVALID=H VSYNC=H HSYNC =H FIELD=H FRAME=H VIL CLK27MOUT tOHD4 DVALID VSYNC/VD HSYNC FIELD FRAME VIL Item Output Data Hold Time Symbol tOHD4 Min. 3.0 Typ. Max Unit nsec Note CL 25pF Rev.0 13 2002/01 ASAHI KASEI 4-6-4 Output Data Timing ( CLK27MOUT, DVALID signal, D7~D0 relation ) 4-6-4-1 CLKINVpin L and Output Control Register DVALID-bit=L VIH CLK27MOUT tOHD2 tOHD1 VIL [AK8850] VIH DVALID VIH VIL D[7:0] Cb0 Y0 Cr0 Cr359 Y719 4-6-4-3 CLKINV pin H and Output Control Register DVALID-bit=L CLK27MOUT tOHD2 DVALID tOHD1 VIH VIL D[7:0] Cb0 Y0 Cr0 Cr359 Y719 VIH VIL Rev.0 14 2002/01 ASAHI KASEI 4-6-5 Reset Timing ( initialization ) Reset Signal ( Reset Signal should be held Low state for 10msec or longer) [AK8850] /RESET pRES Symbol Min. Typ. Max. Unit Note pRES 10 msec Note System Control Pins (SELA, CLKINV, PD etc.) remain in their states for at least 10 clock cycles before/after a reset signal input. /RESET Pulse width Item 4-6-6 Power-Down / Up Sequence CLK sRES /RESET hRES VIL PD VIL Item RESET pulse width (Setting PD mode) RESE pulse width (Returning from PD mode) Symbol sRES hRES Min. 100 10 Typ. Max. Unit CLK msec Note from CLK Rising edge Note) After PD pin becomes High (power down state), /RESETpin status is irrelevant. Rev.0 15 2002/01 ASAHI KASEI 4-6-7 I2C bus Input & Output Timing ( SCL 400KHz cycle mode ) (1) Timing 1 [AK8850] tBUF SDA tHD:STA tR tF tSU:STO 0.7VDD 0.3VDD tF SCL tLOW tR 0.7VDD 0.3VDD tSU:STA Item Symbol Min. Max. Unit Bus Free Time Hold Time (Start Condition) Clock Pulse Low Time Input Signal Rise Time Input Signal Fall Time Setup Time(Start Condition) Setup Time(Stop Condition) tBUF tHD:STA tLOW tR tF tSU:STA tSU:STO 1.3 0.6 1.3 300 300 0.6 0.6 2 usec usec usec nsec nsec usec usec All the figures shown above are not defined by the AK8850 but are defined by I C Bus standard. 2 Please see the I C Bus standard for further details (2) Timing 2 tHD:DAT SDA tHIGH 0.7VDD SCL tSU:DAT 0.3VDD 0.7VDD 0.3VDD Item Symbol Min. Max. Unit Data Setup Time Data Hold Time Clock Pulse High Time tSU:DAT tHD:DAT tHIGH 100(1) 0.0 0.6 0.9(2 nsec usec usec (1) In case of normal I2C bus mode tSU:DAT 250nsec (2) Using under minimum tLOW, this value must be satisfied. Rev.0 16 2002/01 ASAHI KASEI [AK8850] 5. Output Signal Timing Description 5-1. NTSC Input Vertical Sync timing, Field signal and Frame signal timing relations are shown below. The logic states of HSYNC/VSYNC/FIELD/FRAME can be altered via register settings. Depending on the register setting either VSYNC or VD signal is available. FIELD output and FRAME output signals change states on the rising edge of CSYNC just before the 0.5H delay period that is controlled by the Output Control Register. The 0.5H delay timing is shown on page 18. CSYNC HSYNC VSYNC VD FIELD FRAME CSYNC 26 HSYNC VSYNC VD FIELD FRAME ODD (Low) EVEN 26 26 26 26 26 26 26 26 27 27 27 27 27 ODD 52 52 52 1 2 3 4 5 6 7 8 9 10 11 EVEN CSYNC HSYNC VSYNC VD FIELD FRAME 52 52 52 1 2 3 4 5 6 7 8 9 10 11 EVEN ODD CSYNC 26 HSYNC VSYNC VD FIELD FRAME 26 26 26 26 26 26 26 26 27 27 27 27 27 ODD (High EVEN Note) Frame timing signal output is as shown above when standard signals are input to the AK8850. If a Non-standard signal is input to AK8850, the number of Color frame is not guaranteed. When the input signal changes from non-standard to standard, that the Frame timing signal may not change for 512 lines (max) as the AK8850 synchronizes to the input video signal. Rev.0 17 2002/0 ASAHI KASEI 5-2. FIELD/FRAME Signal Output Timing Diagram with NTSC signal input ( CSYNC & FIELD/FRAME0/FRAME1 relationship ) when [Output Control Register] FFDELAY-bit = 0: CSYNC 52 FIELD FRAME CSYNC 26 FIELD FRAME CSYNC 52 FIELD FRAME CSYNC 26 FIELD FRAME (High 26 ODD 26 26 26 26 26 EVEN 26 26 27 27 27 27 27 52 52 EVEN 1 2 3 4 5 ODD 6 7 8 9 10 11 (Low) 26 26 ODD 26 26 26 26 EVEN 26 26 27 27 27 27 27 52 52 EVEN 1 2 3 4 5 ODD 6 7 8 9 10 11 [AK8850] at [Output Control Register] FFDELAY-bit = 1: CSYNC 52 FIELD FRAME CSYNC FIELD FRAME CSYNC FIELD FRAME CSYNC 26 FIELD FRAME (High 26 ODD 26 26 26 26 26 EVEN 26 26 27 27 27 27 27 (Low) 52 52 EVEN 1 2 3 4 5 ODD 6 7 8 9 10 11 26 26 26 ODD 26 26 26 26 EVEN 26 26 27 27 27 27 27 52 52 52 EVEN 1 2 3 4 5 ODD 6 7 8 9 10 11 Rev.0 18 2002/0 ASAHI KASEI [AK8850] 5-3. Output Signal Timing Diagram ( CCIR625 Component input ) The VERTICAL Sync signal, FIELD signal and FRAME signal timing relationships are shown. The logical state of HSYNC/VSYNC/FIELD/FRAME can be altered by using register settings. Either VSYNC or VD output signals are available on the VSYNC output pin, depending upon the register setting. The FIELD output and the FRAME output signals change state on the rising edge of the CSYNC, prior to the 0.5H delay period that is controlled by the output control register. Field/FRAME output timings are shown on pages 20 and 21. CSYNC HSYNC VSYNC VD FIELD FRAME CSYNC 30 HSYNC VSYNC VD FIELD FRAME ODD (Low) EVEN 30 31 31 31 31 31 31 31 31 31 31 32 32 ODD 62 62 62 62 62 62 1 2 3 4 5 6 7 8 EVEN CSYNC HSYNC VSYNC VD FIELD FRAME 62 62 62 62 62 62 1 2 3 4 5 6 7 8 EVEN ODD CSYNC HSYNC VSYNC VD FIELD FRAME ODD EVEN (High 30 30 31 31 31 31 31 31 31 31 31 31 32 32 Rev.0 19 2002/0 ASAHI KASEI 625 Component Signal Output Timing Diagram ( CSYNC & FIELD/FRAME0/FRAME1 relationship ) at [Output Control Register] FFDELAY-bit=0 CSYNC FIELD FRAME0 FRAME1 CSYNC FIELD FRAME0 FRAME1 CSYNC FIELD FRAME0 FRAME1 CSYNC 308 FIELD FRAME0 FRAME1 CSYNC FIELD FRAME0 FRAME1 CSYNC FIELD FRAME0 FRAME1 CSYNC FIELD FRAME0 FRAME1 CSYNC 308 FIELD FRAME0 FRAME1 (High) (High) 309 310 ODD 311 312 313 314 EVEN 315 316 317 318 319 320 321 (High) 308 (Low) (High) 620 621 622 EVEN (High) 623 624 625 309 310 ODD 311 312 313 314 EVEN 315 316 317 318 319 320 321 (High) (Low) 620 621 622 EVEN 623 624 625 1 2 ODD 3 4 5 6 7 8 309 310 ODD 311 312 313 314 EVEN 315 316 317 318 319 320 321 (Low) (Low) 620 (Low) 621 622 EVEN 623 624 625 1 2 ODD 3 4 5 6 7 8 [AK8850] 308 309 310 ODD 311 312 313 314 EVEN 315 316 317 318 319 320 321 620 621 622 EVEN 623 624 625 1 2 ODD 3 4 5 6 7 8 (Low) 1 2 ODD 3 4 5 6 7 8 5-5 625 Component Signal Output Timing Diagram ( CSYNC & FIELD/FRAME0/FRAME1 relationship ) when [Output Control Register ] FFDELAY-bit =1 Rev.0 20 2002/0 ASAHI KASEI [AK8850] CSYNC FIELD FRAME0 FRAME1 CSYNC FIELD FRAME0 FRAME1 CSYNC FIELD FRAME0 FRAME1 CSYNC 620 (Low) 621 622 EVEN 623 624 625 1 2 ODD 3 4 5 6 7 8 308 (Low) (Low) 309 310 ODD 311 312 313 314 EVEN 315 316 317 318 319 320 321 620 621 622 EVEN 623 624 625 1 2 ODD 3 4 5 6 7 8 (Low) 308 FIELD FRAME0 FRAME1 CSYNC FIELD FRAME0 FRAME1 CSYNC FIELD FRAME0 FRAME1 CSYNC FIELD FRAME0 FRAME1 CSYNC 308 FIELD FRAME0 FRAME1 (High) (High) (High) 308 (Low) (High) 620 621 (High) (Low) 620 621 309 310 ODD 311 312 313 314 EVEN 315 316 317 318 319 320 321 622 EVEN 623 624 625 1 2 ODD 3 4 5 6 7 8 309 310 ODD 311 312 313 314 EVEN 315 316 317 318 319 320 321 622 EVEN 623 624 625 1 2 ODD 3 4 5 6 7 8 (High) 309 310 ODD 311 312 313 314 EVEN 315 316 317 318 319 320 321 Rev.0 21 2002/0 ASAHI KASEI [AK8850] 6. Functional Summary 6-1. Clock 1. Line Locked Clock mode: An operating mode where the device operates using a clock synchronized with the Horizontal Sync signal for each line. 2. Frame Locked Clock mode: The device operates using a clock synchronized with the Vertical Sync signal at each Frame. 3. Fixed Clock mode: An external clock is used. These clock modes are set with the Control 2 register. Since both the Line Locked and Frame Locked modes use an input-signal synchronized clock, ITU-R BT.656* compatible output is available, although input signal quality may prevent full ITU-R BT.656 compatibility. 6-2. Analog Interface The AK8850 decodes NTSC-M compatible Composite video signals, S-video and Component signals. For CCIR625 systems, only the Component signal is used. Registers control setup selection. 6-3. Input Signals The device accepts NTSC-M Composite,S-Video,, Composite ( Betacam,MII ) and 625 Component signals ( EBU N10 ). Required input signal quality is as follows. 6-3-1 Composite ,S video input signal quality Item Input Range Video signal input level 6 Color Burst input level 10 Unit dB dB Condition Video signal should be input with -6dB level (divided be a resistor), and through 0.1uF capacitor. 6-3-2. Supporting signal characteristics for Composite and S-video signals Item Process Lack of HSYNC Running with self timing Lack of VSYNC Running with self-timing. When VSYNC is absent for two consecutive cycles, the AK8850 identifies this as a "no-signal" state and sets the NSIG pin High. B/W Video Signal input Set B/W mode using the register. 6-3-3. Component input signal A Standard signal is applied in Component decode mode. Supported Component signal conditions are listed below. Unit [mV] Input video source BETACAM (w/o Setup) BETACAM (with 7.5% Setup) MII (w/o Setup) MII (with Setup ) 625 system (EBU N10) Sync level 286 286 300 300 300 Luminance (Setup Level) 0 53.6 0 52.5 0 Luminance Level (max) 714 714 700 700 700 Luminance (Range) 714 660.4 700 647.5 700 U/V (Range) 504 350 350 243 350 Note Luminance 100% U/V 100% Level Luminance 100% U/V 75% Level Luminance 100% U/V 100% Level Luminance 100% U/V 75% Level Luminance 100% U/V 100% Level 6-4. Analog Input Signal Processing Input Selector : -60 dB ( inter-channel isolation ) PGA : 0 ~ 12 dB AD converter : operates at 27 MHz Line-lock or Frame-lock PLL clocks are used in normal operation. Rev.0 22 2002/01 ASAHI KASEI [AK8850] 6-5. Y/C Separation Function Adaptive Y/C separation: Adaptive Y/C separation enables adjustment of the Chroma Signal Bandwidth. Adaptive Y/C Separation can also be fixed to either 3-line 2 dimensional Y/C separation or single dimension Y/C separation. 6-6. Output Signal Bandwidth At Composite signal input, Luminance Signal Bandwidth : DC ~ 5.75 MHz + 0.5 /- 1.5 dB Chroma Signal Bandwidth : +/- 500 KHz ~ +/- 1 MHz ( -3 dB ) ( 3 ranges selectable ) At Component signal input, Luminance Signal Bandwidth : DC ~ 5.75 MHz +0.5 / -1.5 dB Chroma Signal Bandwidth : DC ~ 5.75 MHz +0.5 / -1.5 dB 6-7. Video Quality Control Function Contrast, Brightness, HUE and Color Saturation levels are adjustable. No HUE adjustment is possible when a Component video signal is input. 6-8. Output Interface ITU-R BT.601 compatible signal output levels Decoded data is output in ITU-R BT.656 format ( depends on the input signal quality ). Ability to detect signals during Active Video period using HSYNC/VSYNC ( FIELD )/ DVALID signals 8-Bit output at 27 MHz rate 6-9. Other Functions Black level signal is output when no signal is applied ( Y = 16Cb,Cr = 128 ) "Lack of signal" input detection I2C Bus Interface ( 400 KHz ) Power Save Mode Closed Caption, VBID, WSS and Video Aspect ratio decoding Functions. Rev.0 23 2002/01 ASAHI KASEI CLAMP_PULSE_SEL [AK8850] 7. Functional Details 7-1. Analog Signal Processing Block Diagram EXTCLP FBCAP1 FBCAP2 FBCAP3 CLPCAP1 CLPCAP2 SYNC1 SYNC2 SYNC3 AIN1 MUX Sync Separaor (Clamp Pulse Generator) CLK IVCXO LLPF LLPFC FLPFC FLPF Clock Module (27MHz Generator 13.5MHz Generator) CLK Mode Select CLK27M CLK13.5M IRef_R1 Composite Y Selector C/Pb Pr CLAMP1 CLAMP2 CLAMP3 PGA1 0.1dB/step 0-12dB PGA2 0.1dB/step 0-12dB PGA3 0.1dB/step 0-12dB 10-bit ADC1 10-bit ADC2 10-bit ADC3 Y Data[9:0] AIN2 AIN3 AIN4 AIN5 AIN6 C Data[9:0] / Cb Data[9:0] Cr Data[9:0] RESET PGA_GAIN [6:0] x 3 CLAMP1_LEV [1:0] INPUT_SEL VREF From Digital Block To Digital Block AVDD AVSS VRP VCOM VRN VREF IREFR2 Rev.0 24 2002/01 ASAHI KASEI [AK8850] 7-2. Analog Signal Process Functional Specifications 7-2-1. Input Signal Selector Module The AK8850 has six (6) input pins. The input signal selector module selects one of the video sources. The Video sources available are single-pin Composite, 2-pin Y / C and 3-pin Component signals. A Video source to be decoded is selected by the [INPUT SIGNAL SELECT REGISTER]. The type of Video signal to be decoded is set by the [INPUT VIDEO STANDARD REGISTER]. COMPOSITE SIGNAL INPUT: This input is digitized by the CLAMP1, PGA1 and ADC1 in the Analog Signal Processing Block Diagram. When decoding composite video, the ADC2 and ADC3 blocks can be placed in power save mode by programming the [ POWER SAVE REGISTER]. Y/C SIGNAL (S-VIDEO ) INPUT: The Y-signal is digitized by the CLAMP1, PGA1 and ADC1 as in the Composite signal input case. The C Signal is digitized by the CLAMP2, PGA2 and ADC2. The ADC3 block can be placed in Power Save mode by programming the [ POWER SAVE REGISTER ]. COMPONENT SIGNAL INPUT: In this case, the Y signal is digitized by the CLAMP1, PGA1 and ADC1 as in the Composite signal input case. The Pb signal is digitized by the CLAMP2, PGA2 and ADC2, while the Pr signal is digitized by the CLAMP3, PGA3 and ADC3. Description of the input signal-type set register and input signal select control register: The input signal type is set by the [ INPUT VIDEO STANDARD REGISTER ] and input signal path is selected by the [ INPUT SIGNAL SELECT REGISTER ]. [Input Video Standard Register] bit 7 bit 6 bit 5 Reserved NENT B/W 0 0 0 bit 4 bit 3 SETUP VS3 Default Value 0 0 bit 2 VS2 0 bit 1 VS1 0 bit 0 VS0 0 [Input Signal Select Register] bit 7 bit 6 bit 5 Reserved Reserved SYNCIN1 0 0 0 bit 4 bit 3 SYNCIN0 INSEL3 Default Value 1 0 bit 2 INSEL2 0 bit 1 INSEL1 0 bit 0 INSEL0 1 [ VS3 : VS0]-bit and NENT-bit setting are also described. [Input Video Standard Register] [VS3:VS0]-bit setting [VS3:VS0]-bit Input Signal source 0000 NTSC 1111 Component 625 (EBU N10) SETUP-bit : SETUP-bit 0 1 Setup or No-Setup No Setup in With Setup signal in Note Note B/W-bit : for Black and White video signal B/W-bit B/W signal or not 0 Color video signal 1 Black and White video Signal Note YC separation function turns off Rev.0 25 2002/01 ASAHI KASEI [AK8850] NENT-bit : Setting for Component signal input NENT-bit Signal source of Component 0 MII 1 Betacam Note 300mV Sync level 286mV Sync level (Supplement) There are 3 categories of Video signals which are summarized in Table 7-2-1-1 below. Classifying Signal source NTSC Composite NTSC YC No. of Lines 525-lines system MII Component in a Frame Betacam Component 625-lines system 286mV Sync level (40IRE ) 300mV Sync level 625 (EBU-N10) Component NTSC Composite NTSC YC Betacam MII Component 625 (EBU-N10) Component Table 7-2-1-1 Sync Level Rev.0 26 2002/01 ASAHI KASEI [AK8850] The input signal path ( input signal setting) is selected by [ INSEL3 : INSEL0 ]-bits ( BIT-3:BIT0) in the [ INPUT SIGNAL SELECT REGISTER]. The upper 2-bits ( INSEL3 : INSEL2 ) identify Composite /YC and Component signals. Signal Select No Signal is selected. Composite signal is input from AIN1 (Default) Composite signal is input from AIN2 Composite signal is input from AIN3 Y-Signal from AIN2 [0,1,1,0] C-Signal from AIN4 Y-Signal from AIN2 [0,1,1,1] C-Signal from AIN4 Y-Signal from AIN3 U-Signal from AIN5 [1,0,1,1] V-Signal from AIN6 As shown in the above table ,the AK8850 accepts following 4 input signals: Composite signal x 3 ch Composite signal x 2 ch + Y / C input x 1 ch Composite signal x 1 ch + Y / C input x 2 ch Composite signal x 1 ch + Y / C input x 1 ch + Component signal x 1 ch Please refer to item ( 1-6 ) of Section 7-2-2 CLAMP for SYNC 1 / 2 / 3 combinations. Register settings for the various input signal types are summarized in the following Table 7-2-1-2. For Black & White signal input, set [ B / W ]-bit to "1". Input Signal Register bit setting [VS3:VS0]-bit [Setup]-bit [NENT]-bit INSEL[3:2]-bit Composite Setup 0000 1 don't care 00 No Setup 0000 0 don't care 00 NTSC Composite 525Component Component Y/C Betacam Setup 0000 1 don't care 01 No Setup 0000 0 don't care 01 Setup 0000 1 1 10 No Setup 0000 0 1 10 Setup 0000 1 0 10 625-System MII No Setup 0000 0 0 10 Component No Setup 1111 0 don't care 10 [INSEL3:INSEL0] (bit3:bit0) [0,0,0,0] [0,0,0,1] [0,0,1,0] [0,0,1,1] Table 7-2-1-2 Rev.0 27 2002/01 ASAHI KASEI [AK8850] 7-2-2. Clamp The CLAMP function stabilizes the AC-coupled Video input signal level. The AK8850 utilizes both an Analog Clamp circuit and a Digital Clamp circuit. When the Composite and Y signals (S-video,Component Y signal ) are input, the SYNC-TIP level or PEDESTAL level of Composite signal and LUMINANCE signal ( Y ) are clamped. The digitized input signal data is further signal-processed and clamped to the PEDESTAL level( digital pedestal clamp ). Clamp functions take place during the clamp pulse, as described below, in (1) SYNC SEPARATION FUNCTION. The Clamp interval is equal to the HSYNC interval (approximately 15 KHz ). Both the C and Pb/Pr signals are clamped at the SYNC-TIP timing of the Luminance signal. (1) SYNC SEPARATION FUNCTION( Clamp timing pulse generation ) In order to separate the SYNC signal of the target signal, the Clamp Timing Pulse is used to clamp the input signal to a pre-determined level which is fed back via the Ain pin. To generate a Clamp timing pulse ,select one of the SYNC1 / SYNC2 / SYNC3 input signals by setting [ SYNCIN1 : SYNCIN0] of the ( INPUT SIGNAL SELECT REGISTER). The selected signal must be a signal which corresponds to AIN1~ AIN6 signals. The separated SYNC signal is used for the clamp timing. Sync-separation is done by slicing approximately 70 mV positive point ( default value ) from the SYNC-TIP level. As described above, the Clamp timing pulse is generated based on the separated signal ( SYNC DET ).The slice point is adjustable by register settings. Rev.0 28 2002/01 ASAHI KASEI [AK8850] ( 1-1) SYNC-TIP Clamp Timing Pulse The Start point and pulse width of the SYNC-TIP timing pulse is set by the [CLAMP TIMING 1 CONTROL REGISTER ]. The Start point of the SYNC-TIP timing pulse is set by [SCLPSTAT 2 : SCLPSTAT 0 ]-bit of the [ CLAMP TIMING 1 CONTROL REGISTER ] as shown below. The CLAMP period ( pulse width ) is set by [SCLPWIDTH 3 : SCLPWIDTH 0 ]-bit of the [ CLAMP TIMING 1 CONTROL REGISTER ]. Clamp pulse point and pulse width setting is further described in item( 1-6 )SYNC-SEPARATION RELATED REGISTER DESCRIPTION. Input Video Signal location of Syn (AIN1/AIN2/AIN3) 380nsec R=620 After LPF SYNC1/2/3 input Sync (HSYNC) After Syncseparation Internal Sync Reference C=510pF 70mV (Default LPF Constance (SYNCDET) (2 + [SCLPSTAT2:SCLPSTAT0]-bit) Clocks 380nsec + (2 + [SCLPSTAT2:SCLPSTAT0]-bit) Clocks 1Clock = 37nsec Synctip clamp Timing pulse [SCLPWIDTH3: SCLPWIDTH0]-bit Clocks Rev.0 29 2002/01 ASAHI KASEI [AK8850] ( 1-2 ) PEDESTAL CLAMP TIMING PULSE The AK8850's Clamp point is initially set to the SYNC-TIP level. It is possible to clamp it at the Pedestal point by changing a register value. The Start point of the Pedestal clamp timing pulse is set by [ PCLPSTAT 2 : PCLPSTAT 0 ]-bit of the [ CLAMP TIMING 2 CONTROL REGISTER] as shown below. The Clamp period ( pulse width ) is set by [ PCLPWIDTH3 : PCLPWIDTH 0]-bit of the [ CLAMP TIMING 2 CONTROL REGISTER ]. SYNC-SEPARATION RELATED REGISTER DESCRIPTION. During the SERRATION pulse period, if no SYNCDET falling edge is detected before the start position set by [ PCLPSTA2 : PCLSTA0]-bit, the Pedestal clamp timing pulse is not generated. This avoids mis-clamping of Serration pulse input. * Operation with typical video input signal * Operation with Serration pulse input signal at HSYNC Input Video Signal In Loacation of HSYNC (AIN1/AIN2/AIN3) 380nsec R=620 After LPF SYNC1/2/3 Input HSYNC After Sync Separation Internal Sync Reference C=510pF 70mV LPF (SYNCDET) 1Clock = 37nsec 2+[PCLPSTA3: PCLPSTA0]-bit [clks] Pedestal Clamp Timing pulse [PCLPWIDTH3: PCLPWIDTH0]-bit Clocks at Serration pulse Input After LPF SYNC1/2/3Input Serration pulse After Sync Separation Internal Sync Reference (SYNCDET) 2+[PCLPSTA3: PCLPSTA0]-bit [clks] Pedestal Clamp Timing pulse Rev.0 30 2002/01 ASAHI KASEI [AK8850] ( 1-3 ) CLAMP PULSE MASK FUNCTION To avoid mis-clamping, the SYNCDET signal is masked outside the SYNC signal period. The masking period is from the rising edge of the SYNCDET signal to 1536 clock periods ( 1 clock = 37 ns ). During this period, no SYNCDET signal is generated ( refer to the timing diagram below ). This pulse mask is reset via register programming ( refer to item 1-6-5 ). Input video SYNCDET 1536 clks CLPMASK ( 1-4 ) EXTERNAL CLAMP TIMING INPUT VIA EXTCLP PIN It is possible to input an external clamp timing pulse via the EXTCLP pin by setting the INCLPTMG-bit and [ FBCLPTMG1 : FBCLPTMG0 ]-bits of the [ CLAMP CONTROL REGISTER ]. For further register settings, please refer to item ( 1-6 ) SYNC SEPARATION REGISTER RELATED DESCRIPTION. ( 1-5 ) CLAMP TIMING PULSE MONITOR FUNCTION It is possible to monitor the internal clamp timing through the EXTCLP pin only when no external clamp timing is used. Output signals monitored on EXTCLP pin are SYNC-TIP clamp timing pulse, Pedestal clamp timing pulse and SYNCDET signal. The target signal is selected by [ EXTCLP1 : EXTCLP0 ]-bit of the [ CLAMP TIMING 1 CONTROL REGISTER ]. ( 1-6 ) SYNC-SEPARATION RELATED REGISTER DESCRIPTION Sync-separation and Clamp pulse related registers are [ INPUT SIGNAL SELECT REGISTER ], [ CLAMP CONTROL REGISTER ], [ CLAMP TIMING 1 CONTROL REGISTER ] and [ CLAMP TIMING 2 CONTROL REGISTER ]. Select Sync-separation signal is done using the [ INPUT SIGNAL SELECT REGISTER ]. [Input Signal Select Register] bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 Reserved Reserved SYNCIN1 SYNCIN0 INSEL3 INSEL2 Default Value 0 0 0 1 0 0 [SYNCIN1:SYNCIN0] (bit5:bit4) 00 01 10 11 No Input Video signal input from SYNC1 pin Video signal input from SYNC2 pin Video signal input from SYNC3 pin Target video signal for Sync separation bit 1 INSEL1 0 bit 0 INSEL0 1 [ SYNCIN 1 : SYNCIN 0 ]-bit selects one of the SYNC 1 / 2 / 3 input signals to generate the clamp pulse. Rev.0 31 2002/01 ASAHI KASEI [AK8850] ( 1-6-1 ) CLAMP TIMING PULSE SOURCE SET Input clamp setting is done via the [ CLAMP CONTROL REGISTER ]. [Clamp Control Register] bit 7 bit 6 UNMASK Reserved 0 0 bit 5 ACLAMP 0 bit 4 INCLPTMG bit 3 FBCLPTMG1 bit 2 FBCLPTMG0 bit 1 CLPLVL1 0 bit 0 CLPLVL0 0 Default Value 0 0 0 [ INCLPTMG]-bit sets the clamp timing pulse of the input clamp. INCLPTMG-bit (bit-4) 0 1 Clamp timing pulse Generation Clamp timing pulse generated by Internal Clamp pulse generator Clamp timing pulse from EXTCLP pin [ FBCLPTMG1 : FBCLPTMG0]-bit sets the clamp position and the clamp source. [FBCLPTMG1:FBCLPTMG0]-bit (bit-3:bit-2) 00 01 10 11 Clamp timing pulse Video signal is clamped at synctip level with internal Clamp timing pulse (Default) Video signal is clamped at synctip level with External Clamp timing pulse Video signal is clamped at pedestal level with internal Clamp timing pulse Reserved Combinations of INCLPTMG-bit, the [FBCLPTMG1 : FBCLPTMG0 ]-bit and input / output setting of the EXTCLP pin in various modes are shown in the following table. Some combinations are"Prohibited" as shown in the table, and therefore should not be selected ( otherwise internal timing has priority ). Internal clamp timing monitoring is described below.. [FBCLPTMG1:FBCLPTMG0]-bit Synctip Clamp FBCLPTMG1=0 Internal Timing External Timing FBCLPTMG0=0 FBCLPTMG0=1 0 (Internal Timing) 1 (External Timing) EXTCLP = OUTPUT Synctip Clamp Prohibit Pedestal Clamp FBCLPTMG1 =1 Internal Timing External Timing FBCLPTMG0=0 FBCLPTMG0=1 EXTCLP = OUTPUT Pedestal EXTCLP = INPUT Pedestal clamp INCLPTMG-bit Prohibit EXTCLP =INPUT Synctip Clamp EXTCLP = INPUT Pedestal Clamp Prohibit ( 1-6-2 ) INTERNAL CLAMP TIMING MONITORING FUNCTION VIA EXTCLP PIN It is possible to monitor the clamp timing pulse on EXTCLP pin. This is enabled by the [ EXTMON1 : EXTMON0 ]-bit of the [ CLAMP TIMING1 CONTROL REGISTER ]. The timing pulse monitor function is disabled when the external clamp pulse input is selected. * [ CLAMP TIMING 1 CONTROL REGISTER ] bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 EXTMON1 EXTMON0 SCLPSTAT2 SCLPSTAT1 SCLPSTAT0 SCLPWIDTH2 SCLPWIDTH1 SCLPWIDTH0 Default Value 0 0 0 0 0 Monitoring of clamp timing is possible by setting [ INCLPTMG : FBCLPTMG 1 : FBCLPTMG 0 ]-bit. [INCLPTMG: FBCLPTMG1:FBCLPTMG0]-bit [000] [010] Monitor with EXTCLP pin possible possible Note Synctip Clamp Pedestal Clamp Rev.0 32 2002/01 ASAHI KASEI [AK8850] Monitor pulse is selected as follows. [EXTMON1:EXTMON0]-bit 00 01 10 11 Monitor source High Impedance ( Unavailable monitoring) Internal Synctipu clamp timing pulse Internal pedestal clamp timing pulse SYNCDET pulse Note Default ( 1-6-3 ) SYNC-TIP CLAMP TIMING PULSE SET When using the internal SYNC-TIP clamp timing pulse for clamp functions, set the start position and pulse width of the SYNC-TIP clamp timing pulse using the [ CLAMP TIMING1 CONTROL REGISTER ].This setting is valid only when the [ INCLPTMG : FBCLPTMG1 : FBCLPTMG0 ]-bits are set to use the internal clamp pulse for SYNC-TIP clamping ( it is invalid if external clamp pulse is used ). To monitor the clamp pulse timing generated by the internal clamp circuit, ensure that [ EXTMON1 : EXTMON0 ]-bit of the [ CLAMP TIMING1 CONTROL REGISTER ] is properly set. The slice level is adjustable by setting [ SLCLV 1 : SLCLV 0 ]-bit of the [ CLAMP TIMING 2 CONTROL REGISTER ]. * [ CLAMP TIMING1 CONTROL REGISTER ] bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 EXTMON1 EXTMON0 SCLPSTAT2 SCLPSTAT1 SCLPSTAT0 SCLPWIDTH2 SCLPWIDTH1 SCLPWIDTH0 Default Value 0 0 0 0 0 0 Start position of the Analog SYNC-TIP clamp timing pulse is set by [ SCLPSTA2 : SCLPSTAT0]-bit ,and the clamp pulse width is adjusted using the [ SCLPWIDTH3 : SCLPWIDTH0 ]-bit. * When [ SCLPSTA2 : SCLPSTAT0 ]-bit and [ SCLPWIDTH3 : SCLPWIDTH0 ]-bit are valid, settings are as follows. [INCLPTMG: FBCLPTMG1:FBCLPTMG0]-bit [000] [010] [011] monitor with EXTCLP Available Available Unavailable Note Internal Synctip clamp pulse internal Pedestal clamp timing Pulse External Pedestal clamp timing pulse SYNC-TIP clamp pulse related settings are shown below. * SYNC-TIP clamp pulse start position set by [ SCLPSTAT2 : SCLPSTAT0 ]-bit Start position from the falling edge [SCLPSTAT2:SCLPSTAT0]-bit Actual Clamp pulse timing position of Synchronization pulse 000 Passed after 0-Clocks (0nsec) Passed after 2-Clocks (74nsec) 001 Passed after 2-Clocks (74nsec) Passed after 4-Clocks (148nsec) 010 Passed after 4-Clocks (148nsec) Passed after 6-Clocks (222nsec) 011 Passed after 6-Clocks (222nsec) Passed after 8-Clocks (296nsec) 100 Passed after 8-Clocks (296nsec) Passed after 10-Clocks (370nsec) 101 Passed after 10-Clocks (370nsec) Passed after 12-Clocks (444nsec) 110 Passed after 12-Clocks (444nsec) Passed after 14-Clocks (481nsec) 111 Passed after 14-Clocks (518nsec) Passed after 16-Clocks (592nsec) [ SCLPSTAT2 : SCLPSTAT0 ]-bit is used to fine-tune the start position whose default value is [001], or 2 clocks (74ns). The clamp start position is adjusted with the [ SCLPSTAT2 : SCLPSTAT0 ]-bit as follows. The actual clamping position occurs 2 clock cycles after sync pulse is generated.. Rev.0 33 2002/01 ASAHI KASEI [AK8850] * SYNC-TIP clamp pulse width set by [ SCLPWIDTH2 : SCLPWIDTH0 ]-bit [SCLPWIDTH2: SCLPWIDTH0]-bit Pulse width 000 2-Clocks (74nsec) 001 4-Clocks (148nsec) 010 8-Clocks (296nsec) (Default) 011 16-Clocks (592usec) 100 24-Clocks (888nsec) 101 32-Clocls (1.18usec) 110 40-Clocks (1.48usec) 111 48-Clocks (1.78usec) SYNC-TIP clamp pulse width is set using the [ SCLPWIDTH2 : SCLPWIDTH0 ]-bit = [010], with ( 8 clocks = 296 ns) as the default value. Clamp pulse width can be adjusted using the [ PCLPWIDTH3 : PCLDWIDTH0 ]-bit as shown below. * [ CLAMP TIMING2 CONTROL REGISTER ] bit 7 bit 6 bit 5 SLCLV1 SLCLV0 PCLPWIDTH2 bit 4 PCLPWIDTH1 bit 3 PCLPWIDTH0 bit 2 PSCLPSTAT2 bit 1 PCLPSTAT1 bit 0 PCLPSTAT0 Default Value 0 0 0 1 1 Please use SLCLV1 : SLCLV0 to adjust the SYNC-TIP slice position. [SLCLV1: SLCLV0]-bit 1 0 0 Slice Level 00 Sliced at the position from about 70mV over synctip. 01 Sliced at the position from about 140mV over synctip. 10 Invalid setting 11 Sliced at the position from about 105mV over synctip. The default SYNC-TIP clamp timing pulse generates a clamp pulse as shown in the following timing diagram. Video Input Sync position (AIN1/AIN2/AIN3) 380nsec R=620 after LPF SYNC1/2/3 input HSYNC After Sync Separation Internal Sync Reference C=510pF 70mV(Default LPF (SYNCDET) 2[clks] + 2[clks] = 4[clks] (148[nsec]) 380[nsec] + 148[nsec] = 528[nsec] 1Clock = 37nsec Synctip Clamp timing pulse 296 [nsec] 824 [nsec] Default Synctip Clamp Timing Rev.0 34 2002/01 ASAHI KASEI [AK8850] ( 1-6-4 ) SETTING OF PEDESTAL CLAMP TIMING PULSE Both the start position and pulse width of the Pedestal clamp timing pulse are programmable.It is done using the [ CLAMP TIMING 2 CONTROL REGISTER ]. This is valid only when [ INCLPTMG : FBCLPTMG1 : FBCLPTMG0 ]-bit is set, causing the internal clamp pulse to be used for Pedestal clamping ( it is invalid if an external clamp pulse is used ). To monitor the clamp timing pulse generated by an internal clamp timing circuit, proper setting of the [ EXTMON1 : EXTMON0 ]-bits of the [ CLAMP TIMING1 CONTROL REGISTER ] is required. * [ CLAMP TIMING2 CONTROL REGISTER ] bit 7 bit 6 bit 5 SLCLV1 SLCLV0 PCLPWIDTH2 bit 4 PCLPWIDTH1 bit 3 PCLPWIDTH0 bit 2 PSCLPSTAT2 bit 1 PCLPSTAT1 bit 0 PCLPSTAT0 Default Value 0 0 0 1 1 1 0 0 The Start position of the Pedestal clamp timing pulse is set by [ PCLPSTA2 : PCLPSTAT0 ]-bit,and the clamp pulse width is adjusted by [ PCLPWIDTH3 : PCLPWIDTH0 ]-bit. * When [ PCLPSTA2 : PCLPSTAT0 ]-bit and [ PCLPWIDTH3 : PCLPWIDTH0 ]-bit are valid,the setting is as follows. [INCLPTMG: FBCLPTMG1:FBCLPTMG0]-bit [010] [110] Monitoring with EXTCLP Available Unavailable Internal pedestal clamp timing pulse External Pedestal clamp timing pulse Set the start position and the pulse width of the Pedestal clamp timing pulse. * Pedestal clamp timing pulse start position set by [ PCLPSTAT2 : PCLPSTAT0 ]-bit Start position from the falling edge of [PCLPSTAT2:PCLPSTAT0]-bit Color subcarrier Cycles from the falling edge of (bit-2:bit-0) HSYNC Synchronization pulse 000 001 010 011 100 101 110 111 Passed after 118-Clocks (4.37usec) Passed after 126-Clocks (4.65usec) Passed after 132-Clocks (4.88usec) Passed after 140-Clocks (5.18usec) Passed after 148-Clocks (5.49usec) Passed after 156-Clocks (5.77usec) Passed after 164 Clocks (6.07usec) Passed after 172 Clocks (6.36usec) 17Cycles 18Cycles 19Cycles (Color burst start position of the standard NTSC video signal) 20Cycles 21Cycles (Default) 22Cycles 23Cycles 24Cycles [ PCLPSTAT2 : PCLPSTAT0 ]-bit is used to fine-tune the start position which is set to be 2 clocks later [100 ] as default value. Clamp pulse start position changes as follows by [ PCLPSTAT2 : PCLPSTAT0 ]-bit. * Pedestal Clamp pulse width set by [ PCLPWIDTH2 : PCLPWIDTH0]-bit [PCLPWIDTH2: PCLPWIDTH0]-bit (bit-6:bit-4) 000 001 010 011 100 101 110 111 Pulse width 16-Clocks (592nsec) 24-Clocks (888nsec) 28-Clocks (1.04usec) 32-Clocks (1.18usec) 40-Clocks (1.48usec) 44-Clocks (1.63usec) 48-Clocks (1.78usec) 52-Clocks (1.92usec) Pedestal clamp pulse width is set to its default value of [011] via the [ PCLPWIDTH2 : PCLPWIDTH0 ]-bits =( 32 clocks = 1.18 micro sec ). The clamp pulse width is adjusted using the [ PCLPWIDTH3 : PCLPWIDTH0 ]-bit as follows. Rev.0 35 2002/01 ASAHI KASEI [AK8850] The Pedestal clamp timing pulse at the default state generates a clamp pulse as shown in the following timing diagram. 5.3usec 2.5usec Video signal Input Position of HSYNC (AIN1/AIN2/AIN3) 4.92usec=133[clk] 380nsec After LPF SYNC1/2/3 input HSYNC After Sync Separation Internal Sync Reference 70mV (SYNCDET) [PCLPSTA3: PCLPSTA0]-bit Clocks Default value is 21 cycles 1Clock = 37nsec Pedestal clamp timing pulse ( Default 5.48usec = 148 [clk] ) [PCLPWIDTH3: PCLPWIDTH0]-bit Clocks Default Pedestal clamp timing ( 1-6-5 ) CLAMP TIMING PULSE MASK FUNCTION The Clamp timing pulse generation is masked at the default state to avoid mis-clamping outside the SYNC signal timing. This masking function can be disabled. * [ CLAMP CONTROL REGISTER ] set is done by UNMASK-bit UNMASK-bit Function 0 Masked 1 Un-Masked For typical use,please set UNMASK bit =0. default Rev.0 36 2002/01 ASAHI KASEI [AK8850] ( 2 ) INPUT SIGNAL CLAMP FUNCTION This function clamps the input signal to a proper level. The circuit clamps the SYNC-TIP level of input signal to approximately 0.7 V. The input signal is clamped at the position as shown below. The clamp timing pulse is controlled by either the internal Sync-separation circuit or by an externally-fed clamp timing pulse via EXTCLP pin ( please refer to SYNC-TIP clamp timing pulse item ). Clamp Level Clamp timing ( 2-1 ) INPUT CLAMP CONTROL REGISTER: * INPUT SIGNAL CLAMP ON /OFF BIT : ACLAMP-bit ( bit-3 ) ACLAMP 0 1 Function Clamp ON (default) Clamp OFF The Input signal clamp function can be turned -off, for example, when DC signals are input.. Set ACLAMP=0 ( ON ) for normal operation. ( 3 ) ANALOG CLAMP FUNCTION This function clamps the input signal using analog signal processing for a higher degree of precision, enabling SYNC-TIP to be clamped to approximately 0.7 V by the input signal clamping. Either of the SYNC-TIP clamp or the Pedestal clamp is selectable by the [ CLAMP CONTROL REGISTER ]. Clamp timing is controlled by a clamp pulse that is generated by an internal Sync-separation circuit. It is also possible to control it with an external signal connected to the EXTCLP pin. Either the SYNC-TIP clamp or the Pedestal clamp must be selected and its clamp level set by [ CLPLVL 1 : CLPLVL 0 ]-bit. If an internal clamp pulse is used, the selected clamp pulse can be output on the EXTCLP pin. When the C signal and Pb / Pr component signals are input, the clamp levels of CLAMP2 / CLAMP3 are set to fixed values. ( 3-1 ) CLAMP CONTROL REGISTER DESCRIPTION Clamp function is set by [ CLAMP CONTROL REGISTER ]. * [ CLAMP CONTROL REGISTER ] bit 7 bit 6 bit 5 CLPMASK Reserved ACLAMP 0 0 0 bit 4 INCLPTMG bit 3 FBCLPTMG1 bit 2 FBCLPTMG0 bit 1 CLPLVL1 0 bit 0 CLPLVL0 0 Default Value 0 0 0 [CLPLVL1: CLPLVL0]-bit (bit1:bi0) [00] [01] Clamp level Synctip Pedestal Note Clamped at synctip level. When internal clamp pulse is used, set to this mode Clamped at Pedestal Level For 286mV Sync levels and Analog Pedestal Clamp settings, use this mode. 286mV Sync : NTSC Composite , Y/C signal , Betacam Component Clamped at Pedestal Level For 300mV Sync level and Analog Pedestal Clamp settings, use this mode. 300mV Sync : 625 Component, MIIComponent Analog clamp function is off [10] [11] Pedestal Clamp OFF The control clamp timing is done by setting the clamp pulse timing [ CLPTMG 1 : CLPTMG 0 ]-bit. Rev.0 37 2002/01 ASAHI KASEI [AK8850] * Clamp timing is set by [ FBCLPTMG 1 : FBCLPTMG 0 ]-bit ( bit-3 : bit-2 ). [FBCLPTMG1:FBCLPTMG0]-bit 00 01 10 11 Clamp Pulse Internal Synctip Clamp pulse Internal Pedestal Clamp pulse External clamp timing pulse input from EXTCLP pin. Reserved * Clamp timing and clamp level are summarized in the following table. Internal Clamp timing pulse Bit Set [FBCLPTMG1:FBCLPTMG0]-bit [CLPLVL1:CLPLVL0]-bit External Clamp timing pulse 286mV Sync signal Synctip Pedestal Clamp Clamp 300mV Sync signal Synctip Pedestal Clamp Clamp 286mV Sync signal Synctip Pedestal Clamp Clamp 300mV Sync signal Synctip Pedestal Clamp Clamp 00 00 01 01 00 00 01 10 10 00 10 01 10 00 10 10 ( 4 ) DIGITAL PEDESTAL CLAMP FUNCTION This function clamps at the Pedestal position the Analog-clamped input signal by using digital signal processing. For details, please refer to digital portion details. Rev.0 38 2002/01 ASAHI KASEI [AK8850] 7-2-3 PGA ( PROGRAMMABLE GAIN AMP ) A Programmable Gain Amp ( PGA ) to adjust input signals to their proper levels. The gain range of the PGA is from 0 dB to 12 dB with the gain step of 0.1 dB / step ( 127 steps ).When the AGC function is enabled,PGA1 / PGA 2 / PGA 3 are properly gain set by digital control. AGC function is disabled by default and the gain of each PGA is independently set via registers. PGA Control Register description: To manually control the PGA, the AGC function is turned off by the [ CONTROL 1 REGISTER ]. The AGC function is disabled by default. * [ CONTROL 1 REGISTER ] bit 7 bit 6 FRCSYNC Reserved 1 0 bit 5 INTPOL[1] 0 bit 4 bit 3 INTPOL[0] AGCC1 Default Value 0 0 bit 2 AGCC0 0 bit 1 AGCT1 0 bit 0 AGCT0 0 to the AGC must be disabled in order to set PGA manually. The setting is done as follows : i.e., set [ AGCT 1 : AGCT 0 ] = [ 0,0 ]. [AGCT1:AGCT0](bit-1:bit-0) [0,0] [0,1] [1,0] [1,1] AGC Function Disable (Default) T=1Field T=7Field T=29Field For further details of AGC function, please refer to the AGC description section. * [ PGA 1 /2 /3 GAIN CONTROL REGISTER ] bit 7 bit 6 bit 5 Reserved PGA1/2/3[6] PGA1/2/3[5] 0 1 0 bit 4 PGA1/2/3[4] bit 3 PGA1/2/3[3] bit 2 PGA1/2/3[2] bit 1 PGA1/2/3[1] bit 0 PGA1/2/3[0] Default Value 0 0 0 0 0 Registers for setting the PGA gain values are [ PGA 1 / 2 / 3 GAIN CONTROL REGISTER ]. Each PGA has a corresponding register. [ PGA 1 GAIN CONTROL REGISTER ] example is shown here. bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 Reserved PGA1[6] PGA1[5] PGA1[4] PGA1[3] PGA1[2] PGA1[1] PGA1[0] Default Value 0 1 0 0 0 0 0 0 Each value set by PGA 1 / 2 / 3 [ 6 : 0 ]-bit uses 0.1 dB / step increments. The default gain is set to approximately 6 dB ( PGA 1 /2 / 3 [ 6 : 0 ]= 0x40 ). Rev.0 39 2002/01 ASAHI KASEI [AK8850] 7-2-4 CLOCK MODES The AK8850 operates under the following 3 clock modes. (1) LINE-LOCKED CLOCK MODE A high quality input signal from a Signal generator or DVD can be used and the corresponding Horizontal Sync Signal ( HSYNC ) can be extracted. A clock generated in this way is called Line-Locked Clock. Even if the Line-Locked Clock mode is selected, it is possible for the chip to be forced into Fixed-Clock mode, depending upon the input signal quality (poor or no-input signal conditions). ( 2 ) FRAME-LOCKED CLOCK MODE The Vertical Sync Signal in the input signal is used to generate a clock when skew exists in the input signal, as in the case of a VCR. A clock generated in this way is called Frame-Locked Clock. Even if the Frame-Locked Clock mode is selected, there is a case to be forced to the Fixed-Clock mode which is depending on the input signal quality ( poor or no- input signal conditions). ( 3 ) FIXED-CLOCK MODE A clock not affected by PLL control. ( 4 ) CLOCK AUTO TRANSITION MODE ( default mode ) Depending on the characteristics of the input signal, the clock mode is automatically selected. When the auto select mode is enabled, the AK8850 automatically shifts its clock mode from / to Line-Clocked mode to / from Frame-Locked mode then to Fixed-Clock mode until it selects the optimum mode. Since an input- signal-synchronized clock can be generated in both the Line-Locked Clock and Frame-Locked Clock modes, ITU-R BT.656 compatible output is available if the input signal quality is good enough. In Fixed Clock mode operation, the AK8850's PLL is disabled. This clock mode is usually selected when the input signal quality is poor and the Auto Clock mode is set by Clock Mode Register. In this mode, the input clock must be synchronized with the input signal so that output data remains compatible with ITU-R BT.656 specifications. An external VCXO clock circuit connection is shown below. The AK8850 internally switches the Line and the Frame-Locked Loop Filter outputs, and adds the V-I converted current and the internal current DAC output together, then it outputs this value on the IVCXO pin. By connecting an external resistor to this pin, a control voltage to the external VCXO is provided. A voltage to control the oscillating center frequency of the VCXO is adjustable by setting the above-mentioned current DAC input code, using the PLL-DAC Code Set Register ( address : 0x47 ). In this case, adjusting the external VCXO oscillating center frequency is accomplished by selecting the Fixed Clock mode [ CONTROL 2 REGISTER ]. AK8850 27MHz VCXO CLK Internal Clock DAC IVCXO 10K Gm LLPF RL LINE PLL CIRCUIT C2L C1L LPF SW FLPF FRAME PLL CIRCUIT RF Clock Control Register Description : Clock mode is controlled by the [ CONTROL * [ CONTROL 2 REGISTER ] bit 7 CLKMODE1 C2F C1F PLL BLOCK DIAGRAM bit 6 CLKMODE0 bit 5 ACC1 bit 4 ACC0 Default Value bit 3 DPCC1 bit 2 DPCC0 bit 1 DPCT1 bit 0 DPCT0 1 1 0 0 0 0 0 1 Rev.0 40 2002/01 ASAHI KASEI [AK8850] * [ CLKMODE1 : CLKMODE0 ]-bit set [CLKMODE1: CLKMODE0 ] 00 01 Fixed clock Line-Locked Clock External Clock mode Line Lock Clock mode According to the input video signal quality, AK8850 works in Fixed clock mode. Frame Lock Clock mode According to the input video signal quality, AK8850 works in Fixed clock mode. According to the Input video signal quality, Clock mode is switched to the most suitable clock mode.(default) 10 11 Frame-Locked Clock Auto Clock Mode The VCXO's oscillating center frequency control voltage is adjusted by setting the DAC output current value [ PLL DAC SET REGISTER ]. In Fixed Clock mode operation, the VCXO oscillating frequency is fixed by the value set here. * [ PLL DAC SET REGISTER ] bit 7 PLLDACI7 1 bit 6 PLLDACI6 0 bit 5 PLLDACI5 0 bit 4 PLLDACI4 0 bit 3 PLLDACI3 0 bit 2 PLLDACI2 0 bit 1 PLLDACI1 0 bit 0 Reserved 0 The DAC's upper 7 bits are valid. Adjustable DAC current value ranges are as follows. PLLDAC[7:1] 0000000 1111111 [uA] Typ.) 0 127 ( 7-2-5 ) LOOP FILTER The AK8850 requires external loop filters. Proper loop filters should be connected for the Line-Locked and the Frame-Locked PLLs respectively. The optimum value of the loop filter constant varies with the VCXO gain [ ppm / V ] characteristics. LLPF (For Line Lock) FLPF (For Frame Lock C2 R1 C1 LLPFC ( For Line Lock) FLPFC ( For Frame Lock) An example of the loop filter constant for a 100 ppm/V VCXO is shown ( IVCXO output load resistor at 10 Kohm ).This loop filter constant ( reference value ) is set by the [ PLL CONTROL REGISTER ] ( Sub address 0x46 ) [ LPGAUTO ]-bit [LPGAUTO] - bit = 0 (Default) [LPGAUTO]-bit = 1 R C1 C2 R C1 C2 Line Lock 9.1k 6.8uF 0.68uF 18k 3.4uF 0.34uF Frame Lock 5.6M 0.18uF 0.018uF 3.3M 0.3uF 0.03uF Rev.0 41 2002/01 ASAHI KASEI [AK8850] ( 7-2-6 ) ADC The AK8850 integrates three 27 MHz 10-bit ADCs ( ADC1 / ADC2 / ADC3 ).Each ADC can be disabled by the [ POWER SAVE MODE REGISTER ]. bit 7 bit 6 Reserved Reserved 0 0 bit 5 Reserved 0 bit 4 bit 3 Reserved ADC2 Default Value 0 0 bit 2 ADC1 0 bit 1 ADC0 0 bit 0 PS 0 * ADC1 /2 / 3 - bit set ADC1/2/3-bit 0 1 Function ADC1/2/3 Active mode ADC1/2/3 Sleep mode Note Each ADC can be set sleep mode individually Rev.0 42 2002/01 ASAHI KASEI [AK8850] 7-3 DIGITAL SIGNAL PROCESSING BLOCK DIAGRAM 7-3-1 Digital Block Details CLK13.5MHz CLK27MHz U V Y Pixel Interpolator 601 Formatter Y Y HALFCLKOUT CLK27MOUT 656 Formatter & Buffer HSYNC VSYNC FIELD FRAME0 FRAME1 DVALID Composite or Y[9:0] 10-bitAD Decimation filter 27MHz13.5MHz(Composite/Y/C) 13.5MHz6.75MHz(Component Cb/Cr) Y Composite Signal Sync Rejection Contrast Brightness Adaptive YC-Separation Y/C C[9:0] Component Cb[9:0] 10-bitAD Component Cr[9:0] 10-bitAD U Demodulation C Cb Multiplexer Multiplier ACC Multiplier ACC LPF LPF U V V Cr C DATA[7:0] Chroma PLL (HUE Control) PGA_GAIN[6:0] x 3 INPUT_SEL CLAMP1_LEV[1:0] CLAMP_PULSE_SEL CLK_Mode Select RESET Timing Controller & Other Function Sync Detect Sync Separation VCO Control (Phase error Detect) AGC Control CC/VBID/WSS/ASPECT Extraction etc. DFS NSTD NSIG Host Interface DVDD DVSS SELA SCL SDA /RESET Rev.0 43 2002/01 ASAHI KASEI [AK8850] 7-4 DIGITAL SIGNAL PROCESSING FUNCTIONAL SPECIFICATION 7-4-1 Decimation Filter Composite, YC, and Component input signals are sampled at 27 MHz and then are down- sampled to 13.5 MHz by the Decimation Filter. The Frequency Response of the Decimation Filter is shown as follows. F r equ en cy [MH z] 5.0 6.0 7.0 8.0 0.0 10 0 -10 Ga in [dB] -20 -30 -40 -50 -60 -70 1.0 2.0 3.0 4.0 9.0 10.0 11.0 12.0 13.0 7-4-2 SYNC-Separation, SYNC-Detection, Phase-Error Detection This detects SYNC-signal position of the discrete signal. The detected SYNC signal controls the PLL. 7-4-3 DIGITAL PEDESTAL CLAMP This sets the digitized data Pedestal position 240 / 252 levels ( 286 mV-type SYNC / 300 mV-type SYNC ). This function decreases the effect of SYNC level depth variations in the video. The control-time-constant and non-sensing bandwidth can be set by the [ CONTROL 2 REGISTER ]. For 286 mV-type SYNC and 300 mV-type SYNC details, please refer to [ Table 7-2-1-1 ] in section [ 7-2-1 INPUT SIGNAL SELECTOR MODE ]. Digital Pedestal Clamp Control Register description : * [ CONTROL 2 REGISTER ] bit 7 bit 6 bit 4 bit 3 bit 2 bit 1 bit 0 ACC0 DPCC1 DPCC0 DPCT1 DPCT0 CLKMODE1 CLKMODE0 Default Value 1 1 0 0 0 0 0 1 The control-time-constant is set by the [ DPCT1 : DPCT0 ]-bit ,and the non-sensing bandwidth is set by the [ DPCC1 : DPCC0 ]-bit. [DPCT1:DPCT0] 00 01 10 11 Pedestal Clamp OFF Fast (Default) Middle Slow Time Constance About 1.5-Lines About 3.5-Lines About 7.5-Lines bit 5 ACC1 Rev.0 44 2003/01 ASAHI KASEI [AK8850] * Non-Sensing Bandwidth of the Pedestal Clamp is set as follows. 286mV SYNC [DPCC1:DPCC0] Pedestal Level 240 00 Pedestal level is not 240, digital pedestal Default clamp function works. Non-Sensing Bandwidth : +/- 1LSB Pedestal Level is not in the range of 238 01 241, digital pedestal clamp function works Non-Sensing Bandwidth : +/- 2LSB Pedestal Level is not in the range of 236 10 243, digital pedestal clamp function works Non-Sensing Bandwidth : +/- 3LSB Pedestal Level is not in the range of 232 11 247, digital pedestal clamp function works 300mV Sync Pedestal Level 252 Pedestal level is not 252, digital pedestal clamp function works. Non-Sensing Bandwidth : +/- 1LSB Pedestal Level is not in the range of 250 253, digital pedestal clamp function works Non-Sensing Bandwidth : +/- 2LSB Pedestal Level is not in the range of 248 255, digital pedestal clamp function works Non-Sensing Bandwidth : +/- 3LSB Pedestal Level is not in the range of 244 259, digital pedestal clamp function works 7-4-4 AGC ( Automatic Gain Control ) This function sets the PGA gain so that input level is properly set. The PGA gain is calculated so that the SYNC level is equal to 40 IRE / 300 mV ( 286 mV-type Sync / 300 mV-type Sync ) and its value is set to PGA ( classification of 286 mV-type Sync and 300 mV-type Sync is listed in Table 7-2-1-1 ). Gain-calculation and Gain-set are performed during the VBI interval of each Field. The AGC time constant is programmable in 3 steps using the [ CONTROL 1 REGISTER ]. The PGA gain is derived from the SYNC level information only. AGC is performed only on the Composite signal and the Y portion of the YC input and Component input signals. Auto gain is not performanced on the C-signal or Pb / Pr signals. It is assumed that correction of the C-signal is done using the ACC of the digital portion. Correction of the Component Pb /Pr signals should be manually done using the Color Saturation Control function. When the AGC function is disabled by the [ CONTROL 1 REGISTER ], the gain of each channel can be manually set via the [ PGA1 / PGA 2 / PGA 3 GAIN CONTROL REGISTER ]. AGC Control Register Description: AGC is controlled by the [ CONTROL 1 REGISTER ]. * [ CONTROL 1 REGISTER ] bit 7 FRCSYNC bit 6 Reserved bit 5 INTPOL[1] bit 4 INTPOL[0] bit 3 AGCC1 bit 2 AGCC0 bit 1 AGCT1 bit 0 AGCT0 Default Value 1 0 0 0 0 0 0 0 AGC set is defined as follows. Enable / Disable and the Time-Constant ( T ) of the AGC are set . [AGCT1:AGCT0](bit-1:bit-0) [0,0] [0,1] [1,0] [1,1] AGC Function Disable (Default) T=1Field T=7Field T=29Field The AK8850 sets the PGA value so that the SYNC-TIP level is equal to 40 IRE / 300 mV ( 286 mV-type Sync / 300 mV-type Sync ) while the AGC is enabled. The 286 mV-type Sync here means NTSC Composite, NTSC YC input and Betacam Component signals, while the 300 mV-type Sync means 625 Component and MII Component signals. 40 IRE / 300 mV ( 286 mV-type Sync / 300 mV-type Sync ) are equivalent to 240 / 252 ( 10-bit ) in digital code. As the SYNC-TIP is set to 16 ( 10-bit ), Sync sizes are equivalent to 224 / 236 ( 10-bit ) respectively. Sampled Digital Code 240 252 Sync level 224 236 286mV SYNC 300mV SYNC While the AGC is enabled, manual gain adjustment is not possible by the PGA1 / PGA2 / PGA3 GAIN CONTROL Registers ( AGC has higher priority than manual gain adjustments ). Rev.0 45 2003/01 ASAHI KASEI [AK8850] It is also possible to program the non-sensing bandwidth of the AGC by [ AGCC1 : AGCC0 ]-bit of the [ CONTROL 1 REGISTER ]. [AGCC1:AGCC0](bit-3:bit-2) 286mV Sync 300mV Sync Non-Sensing Bandwidth No Non-Sensing Sync level is not 224, AGC Sync level is not 236, AGC [0,0] function works. function works. Bandwidth 1-bit Non-Sensing Sync level is not in the range of Sync level is not in the range of [0,1] 222 - 225, AGC function works. 234 - 237, AGC function works. Bandwidth 2-bit Non-Sensing Sync level is not in the range of Sync level is not in the range of [1,0] 220 - 227, AGC function works. 232 - 239, AGC function works. Bandwidth 3-bit Non-Sensing Sync level is not in the range of Sync level is not in the range of [1,1] 218 - 229, AGC function works. 230 - 241, AGC function works. Bandwidth Same gain as for the Y signal input case is multiplied to the C-signal in Y / C input and the Pb / Pr signals in Component signal input. The gain constant value set for the AGC does not affect to any of the [ PGA1 / PGA2 / PGA3 GAIN CONTROL REGISTER ], regardless of input sources. 7-4-5 Y / C SEPARATION The Y / C Separation function separates the Composite Video input signal into Luminance ( Y ) and Chroma signals ( C ). Three register-selectable Y / C Separation methods are available: Primary Y/C Separation ( Band Pass Filter ), Two Dimensional Y/C Separation ( 3-Line Comb Filter ) and an Adaptive Y/C Separation Filter. For Y/C Separation, the input data is converted CCIR601 compatible formats and it is output as a Y signal when the Black & White mode is selected, during the VBI interval set by [ VBIL4 : VBIL0 ]-bit of the [ VERTICAL BLANKING LENGTH REGISTER ]. The output Cb/Cr signal is at 0x80, or Black level.The resulting output on the AK8850 is selected by VBIDEC-bit of the [ VERTICAL BLANKING LENGTH REGISTER ]. Black level output ( Y= 0x16,Cb/Cr=0x80) at VBIDEC-bit = 0 and Black & White output at VBIDEC-bit=1. The Y/ C Separation function is enabled only when a Composite signal is input. Y/C Separation Control Register Description : The Y/C Separation is controlled by the [ Y/C SEPARATION CONTROL REGISTER ]. * [ Y/C SEPARATION CONTROL REGISTER ] bit 7 bit 6 bit 5 bit 4 bit 3 Reserved Reserved Reserved Reserved CBPFS1 Default 0 0 0 0 0 The Y/C Separation mode is set as follows. [YCSEP1:YCSEP0] (bit-1:bit-0) 00 01 10 11 YC-Separation mode 3-Line 2-D YC-Separation 1-Line BPF YC-Separation Adaptive 3-Line 2-D YC-Separation (Default) Reserved bit 2 CBPFS0 1 bit 1 YCSEP1 1 bit 0 YCSEP0 0 3 types of the Color Band-Limiting Filters are selectable which are used for Y/C Separation. Use the[ Y/C SEPARATION CONTROL1 REGISTER ] to select. The Band Limiting Filters are applicable for all Y/C Separation modes ( in Black & White mode, filter selection becomes invalid since the Y/C Separation function is disabled ). [CBPFS1:CBPFS0] (bit-3:bit-2) 00 01 10 11 Chroma Bandwidth OFF Wide (Default) Middle Narrow Filter characteristic -3dB OFF +/- 1MHz +/- 750kHz +/- 500kHz Rev.0 46 2003/01 ASAHI KASEI [AK8850] 7-4-6 ACC ( Auto Color Control ) This function adjusts the Color Burst level of the C-signal input to its appropriate level, which is 40 IRE ( with NTSC Composite ,Y/C input ). The adjustable range is from -12 dB to + 12 dB. The ACC processing can be turned on or off by the [ CONTROL 2 REGISTER ]. Its function is valid for Composite and Y/C inputs ( invalid for Component input ). ACC Control Register Description : ACC is controlled by [ CONTROL 2 REGISTER ]. * [ CONTROL 2 REGISTER ] bit 7 bit 6 CLKMODE1 CLKMODE0 bit 5 ACC1 0 1 1 bit 4 bit 3 ACC0 DPCC1 Default Value 0 0 bit 2 DPCC0 0 bit 1 DPCT1 0 bit 0 DPCT0 1 Enable/Disable and the Constant ( T ) of the ACC are set as follows. [ACC1:ACC0](bit-5:bit-4) [0,0] [0,1] [1,0] [1,1] ACC Function Disable (Default) T=2-Field T=8-Field T=30-Field The ACC and the Color Saturation adjustments function independently. Rev.0 47 2003/01 ASAHI KASEI [AK8850] 7-4-7 COLOR KILLER The signal quality of the Chroma signal is evaluated from the Color Burst level of input signal. If this level is lower than a target level, the Chroma signal decoding process is not performed. When the Standard 40 IRE Color Burst input signal level becomes lower than the pre-set value (presettable range is from -17 dB to - ( infinite ),-20 dB at default ), the Color Killer function is activated.The Cb/Cr output signal is fixed to 0x80. When the Color Killer is activated, the C-data output is 0x80, (Black & White mode). Since the Color Killer function checks the Color Burst signal, it is disabled when the Component signal is selected. Operating range of the Color Killer can be set from -17 dB to - ( infinite ). It can be turned on or off by the [ COLOR KILLER CONTROL REGISTER ]. When the Color Killer process is executed, the Chroma signal output becomes Black level ( 0x80 ) which is a similar level in the Black & White mode. However, since the C-signal is subtracted from the Composite signal by the Y/C Separation block, the output result differs from the Black & White mode. Color Killer Control Register Description : Color killer function is controlled by the [COLOR KILLER CONTROL REGISTER ]. * [ COLOR KILLER CONTROL REGISTER ] bit 7 bit 6 bit 5 bit 4 bit 3 CL_KILL Reserved CKLVL5 CKLVL4 CKLVL3 Default Value 1 0 1 0 1 bit 2 CKLVL2 1 bit 1 CKLVL1 0 bit 0 CKLVL0 1 * Turning on and off of the Color Killer function is set by CL-KILL-bit ( bit-0 ) CL_KILL-bit (bit-7) 0 1 Color Killer OFF (Disable) ON (Enable) Default * Turning on and off of the Color Killer function is set by CL-KILL-bit ( bit-0 ) The Color Killer level setting is given in the following equation: ON / OFF decision level of the Color Killer is made by checking the U level after de-modulating the Color Burst signal. A proper input signal gives the U-signal a level of 112. A decision is made within the device by multiplying by 4 the U-signal after de-modulating the input signal. The register set value [ CKLVL5 :CKLVL0 ] is given as: [ CKLVL5 : CKLVL0 ]=10 exp( clk/20 ) *448 where CKL [ dB ] is the level to enable Color Killer. In reverse, the Color Killer enable level is calculated from the register set value as : Input U level = 20 *log ( [ CKLVL5 : CKLVL0 ] / 448 ) i.e., when a lower-than-the input U level signal is input, the Color Killer is activated. U-Signal Level After Demodulation 112 Color Killer Level (max63) Set to 63(max), when the calculated value which is 4 times the demodulated U-signal is less than 63, Color killer is active. Rev.0 48 2003/01 ASAHI KASEI [AK8850] 7-4-8 BLACK & WHITE MODE Black & White mode outputs all input signals as luminance (Y) only. In this mode, the C-signal output becomes 0 level (output code 0x80) and Y/C Separation function is turned off ( Black & White mode ). If Y/C and Component signals are input, the Chroma signal to be output is fixed to 0x80. The Black & White mode is user programmable and it is turned on and off by the [ INPUT VIDEO STANDARD REGISTER ]. Black & White Mode Control Register Description: Black & White mode is controlled by the [ INPUT VIDEO STANDARD REGISTER ] * [ INPUT VIDEO STANDARD REGISTER ] bit 7 bit 6 bit 5 Reserved NENT B/W 0 B/W-bit (bit-5) 0 1 0 0 bit 4 bit 3 SETUP VS3 Default Value 0 0 bit 2 VS2 0 bit 1 VS1 0 bit 0 VS0 0 * ON / OFF of Black & White mode function is controlled by B/W-bit ( bit-5 ) B/W mode set OFF (Color Video signal : default) ON (B/W video signal * Output Status in Black & White mode ( at B/W-bit = 1 ). Output data Y Singal out Cb/Cr Signal out Level converted value to Rec.601 level. Fixed value at 0x80 Above output status is applicable for NTSC ( Composite Y/C ) and 525 & 625 Component signals. 7-4-9 PICTURE ADJUSTING FUNCTION The AK8850 has Picture Quality Adjusting functions which include Contrast, Brightness, Color Saturation and HUE adjustments. ( 1 ) CONTRAST The Contrast adjustment is made by multiplying the Luminance signal ( Y ) by the gain factor which is set by the [ CONTRAST CONTROL REGISTER ]. The Contrast adjustment is made within the range of 0 ~ 2 ( 1/ 255 step ). These arithmetic operations areperformed on 10-bit data. When the result exceeds the specified range,it is clipped to 1023 ( upper limit ) or to 0 ( lower limit ). Contrast Contrast Control Register : * [ CONTRAST CONTROL REGISTER ] bit 7 bit 6 bit 5 CONT7 CONT6 CONT5 bit 4 bit 3 bit 2 bit 1 bit 0 CONT4 CONT3 CONT2 CONT1 CONT0 Default Value 1 0 0 0 0 0 0 0 Sets a multiplying factor over the Luminance signal. Adjustable range is from 0 ~ 2 in 0.008 fraction per step. Default value is 0x80. Rev.0 49 2003/01 ASAHI KASEI [AK8850] ( 2 ) BRIGHTNESS Brightness adjustment is accomplished by adding an offset factor to the Luminance signal which is set by the [ BRIGHTNESS CONTROL REGISTER ]. The adjustable range is +/- 200 ( 255 steps ). Arithmetic operations are performed on the 10-bit data. When the result exceeds the specified range,it is clipped to 1023 ( upper limit ) or to 0 ( lower limit ). Brightness Brightness Control Register : * [ BRIGHTNESS CONTROL REGISTER ] bit 7 bit 6 bit 5 BR7 BR6 BR5 bit 4 bit 3 bit 2 bit 1 bit 0 BR4 BR3 BR2 BR1 BR0 Default Value 0 0 0 0 0 0 0 0 Increases the value of the Luminance signal. Arithmetic operations are done on the 10-bit data and adjustable range is from - 128 to + 127 with 1 fraction per step. The adjustable value per step of the ITU-R BT.601 compatible output is shown in the table below. The register is expressed in 2's complement form and its default value is 0x00. * Adjustable Value Per Each Step Input Video Signal 286mV Sync without Setup 286mV Sync (with Setup) 300mV Sync (without Setup) 300mV Sync ( with Setup ) Add Value (rounding) 1 [BR7:BR0]*100/255 1 [BR7:BR0]*108/255 1 [BR7:BR0]*102/255 1 [BR7:BR0]*111/255 Note NTSC Composite/YC /Betacam NTSC Composite/YC /Betacam MII / EBU-N10 MII ( 3 ) HUE CONTROL HUE adjustment is made by rotating the Chroma signal by a predetermined angle which is set by the [ HUE CONTROL REGISTER ]. HUE adjustment ranges from - 90 degrees to + 90 degrees ( 1/255 step ). HUE control is valid only when either a Composite orY/C signals are input. CR C CB HUE CB Hue Control Register : * [ HUE CONTROL REGISTER ] bit 7 bit 6 bit 5 HUE7 HUE6 HUE5 bit 4 bit 3 bit 2 bit 1 bit 0 HUE4 HUE3 HUE2 HUE1 HUE0 Default Value 0 0 0 0 0 0 0 0 Sets the rotation angle of HUE. Adjustable range is +/- 90 degrees with 0.7 degree HUE rotation per step. Default value is the un-adjusted 0x00. The value is in 2's complement format. The HUE control is valid only when the Composite or Y/C signals are input ( it is disabled for Component input ). NTSC(525 System) Composite Y/C Component Betacam MII This Register is disable 625 System Component This register is Disable This Register is functioned Rev.0 50 2003/01 ASAHI KASEI [AK8850] ( 4 ) COLOR SATURATION Color Saturation adjustment is made by multiplying the Chroma signal with a gain factor which is set by the [ SATURATION CONTROL REGISTER ]. The Color Saturation is adjustable range is from - ( infinite ) to + 6 dB ( 1/ 255 step ). Arithmetic operations are performed on the 10-bit data. When the result exceeds the specified range, it is clipped to 1023 ( upper limit ) or to 0 ( lower limit ). CR Chrominace Signal Scaling CR Chrominace Signal CB Saturation CB Saturation Control Register : * [ SATURATION CONTROL REGISTER ] bit 7 bit 6 bit 5 SAT7 SAT6 SAT5 bit 4 bit 3 bit 2 bit 1 bit 0 SAT4 SAT3 SAT2 SAT1 SAT0 Default Value 1 0 0 0 0 0 0 0 Sets the Chroma signal multiplying factor. The adjustable range is from - ( infinite ) to + 6 dB ( 0 ~ 2 ) with 0.008 fraction per step. Default value is 0x80. Rev.0 51 2003/01 ASAHI KASEI [AK8850] 7-4-10 VERTICAL BLANKING INTERVAL This section describes setting the Vertical Blanking Interval (VBI ) and to set tasks to be performed during this interval. The Vertical Blanking Interval is set by [ VBIL4 : VBIL0 ]-bit of the [ VERTICAL BLANKING LENGTH REGISTER ].( hereafter,VBI period means an interval defined by [ VBIL4 : VBIL0 ]-bit ). Default value is 0x14 ( 20 lines ). For normal operation, it is recommended to set the VBI interval to be more than 9 / 7 ( 525 line system / 625 line system ). The V-bit transition point of the Video Timing Reference Code can be altered by the TRSVSEL-bit of the [ VERTICAL BLANKING LENGTH REGISTER ]. TRSVSEL-bit selects either of the ITU-R BT.656 or SMPTE 125M Standards compatibility. The relationship between TRSVSEL-bit and the Video Timing Reference Code V-bit is shown in the table below. TRSVSEL-bit 0 1 Standard ITU-R BT.656 SMPTE125M During the VBI period, the black level ( Y = 0x10,Cb/Cr= 0x80 ) is output by default. By setting the VBIDEC-bit of the [ VERTICAL BLANKING LENGTH REGISTER ] to [1], the Y/C Separation function on those lines which are specified during VBI interval is turned off and input signal is directly output as a Y signal. The SETUP-bit of the [ INPUT VIDEO STANDARD REGISTER ] becomes invalid during VBI period ( no setup process is executed ). Turning the setup process on /off on the latter half of a scan line line ( 0.5 H ) can be controlled by the HALFSU-bit which is applied only to the first line of the second Field of Active Video. VBID Control Register Description : * [ VERTICAL BLANKING LENGTH REGISTER ] bit 7 bit 6 bit 5 bit 4 bit 3 VBIDEC TRSVSEL HALFSU VBIL4 VBIL3 Default Value 0 0 0 1 0 bit 2 VBIL2 1 bit 1 VBIL1 0 bit 0 VBIL0 0 The VBI period is set by [ VBIL4 : VBIL0 ]-bit. NTSC default values and typical setups of 625 Component signals are shown in the table below. 525 System [VBIL4:VBIL0]-bit Component Composite Y/C Betacam MII 0x14 Default (20-Decimal) Line1 ~ Line20 Line263.5 ~ Line283.5 (from 430th pixedl of Line-263 to 429th pixel of Line-283) 625 System Component 0x18 (24-Decimal) Line623.5 ~ Line625 Line1 ~ Line22.5 Line311 ~ Line335 VBI-Line The VBI start line period for 625 Component Video is Line 624. The VBI period of Field -2 is given as : For 525 system, from 264 ( fixed value ) to ( set-value ) + 245. For 625 system,from 311 ( fixed value ) to ( set value ) + 311. TRSVSEL-bit is the control bit that specifies the V-bit in the REC. 656 EAV/SAV code. This bit is set by [ VBIL4 : VBIL0 ] and is not affected by VBI period as shown below. * < V-bit value in Rec.656 TRS and the line relationship > V-bit V-bit = 0 V-bit = 1 NTSC(525 System) Composite/YC/Component(MII,Betacam) TRSVSEL=0 TRSVSEL=1 Line10 ~ Line263 Line20 ~ Line263 Line273 ~ Line525 Line283 ~ Line525 Line1 ~ Line9 Line264 ~ Line272 Line1 ~ Line19 Line264 ~ Line282 625 System Component (EBU N10) TRSVSEL=0 TRSVSEL=1 Line23 ~ Line310 Line336 ~ Line623 Line1 ~ Line22 Line311 ~ Line335 Line624 ~ Line625 note) TRSVSEL-bit setting is as shown above. It is not affected by [ VBIL4 : VBIL0 ]-bit. TRSVSEL-bit setting is shown above for all modes of 525/625 systems. Rev.0 52 2003/01 ASAHI KASEI [AK8850] VBIDEC-bit is the control bit that specifies the device operation during the period is assigned by VBI [4 : 0]-bit. The output code is determined by the VBI period , VBIDEC-bit, HALFSU-bit and SETUP-bit of the [ INPUT VIDEO STANDARD REGISTER ]. When HALFSU-bit = 1, the SETUP processing is executed on the latter half 0.5 H time of the first Line in the second Field. Output status is shown in the following table. NTSC (525 System) VBIDEC-bit = 0 HALFSU-bit = 0 HALFSU-bit=1 Line-1 - VBIDEC-bit = 1 HALFSU-bit=0 HALFSU-bit=1 Y =Input Signal C = 0x80 No Setup Process Line-9 Line-10 - Y = 0x10 C = 0x80 Y = 0x10 C = 0x80 Normal decode procidure No Setup Process Y = 0x10 C = 0x80 Y = 0x10 C = 0x80 1st Field [VBIL4:VBIL0] [VBIL4:VBIL0] + 1 - Line-263.5 (till 429th pixel of Line-263) Line-263.5 (from 430th pixel of Line-263) - SETUP-bit = 0 Last pixel of Line263 Line-264 - Line-272.5 (till 429th pixel of Line272) Line-272.5 (from 430th pixel of Line-272) - 263.5 + [VBIL4:VBIL0] 2nd Field (till 429th pixel of Line(263+[VBIL4:VBIL0])) Y = 0x10 C = 0x80 Y =Input signal C = 0x80 No Setup Process 263.5 + [VBIL4:VBIL0] (from 430th pixel of Line(263+[VBIL4:VBIL0])) - Line-263.5 + Last pixel of [VBIL4:VBIL0] (858th pixel of Line(263+[VBIL4:VBIL0])) Normal decode procidure No Setup Process Normal decode procidure No Setup Process Y = 0x10 C = 0x80 Y = 0x10 C = 0x80 Normal decode procidure Setup Process Y = 0x10 C = 0x80 Y = 0x10 C = 0x80 Line-264 + [VBIL4:VBIL0] - Line-525 Line-1 - Line-9 Line-10 - Y =Input Signal C = 0x80 No Setup Process 1st Field [VBIL4:VBIL0] [VBIL4:VBIL0] + 1 - Line-263.5 Line-263 429 Line-263.5 (from 430th pixel of Line-263) - SETUP-bit = 1 the last pixel of Line263 Line-264 - Line-272.5 (till 429th pixel of Line272) Line-272.5 (from 430th pixel of Line-272) - 263.5 + [VBIL4:VBIL0] 2nd Field (till 429th pixel of Line(263+[VBIL4:VBIL0])) Y = 0x10 C = 0x80 Y =Input Signal C = 0x80 No Setup Process 263.5 + [VBIL4:VBIL0] (from 430th pixel of Line(263+[VBIL4:VBIL0])) - the last pixel of Line-263.5 + [VBIL4:VBIL0] (till 858th pixel of Line(263+[VBIL4:VBIL0])) Normal decode process No Setup Procedure Normal decode process Setup Process Normal decode process No Setup process Normal decode process. Setup Process Line-264 + [VBIL4:VBIL0] - Line-525 Normal decode process. Setup Process Rev.0 53 2003/01 ASAHI KASEI [AK8850] (1) VBIDEC-bit = 0 / HALFSU-bit = 0 / SETUP-bit = 0 VBILENGTH [VBIL4:VBIL0] Normal decode process No setup process 524 525 1 2 3 4 5 Y=0x10 Cb/Cr=0x80 6 7 8 9 10 11 Y=0x10 Cb/Cr=0x80 Y=0x10 Cb/Cr=0x80 Normal decode process No setup process Normal decode process No setup process Y=0x10 Cb/Cr=0x80 263 264 265 266 267 268 269 270 271 272 273 VBILENGTH [VBIL4:VBIL0] (2) VBIDEC-bit = 1 / HALFSU-bit = 0 / SETUP-bit = 0 VBILENGTH [VBIL4:VBIL0] Normal decode process No setup process 524 525 1 2 3 4 5 Y=0x10 Cb/Cr=0x80 6 7 8 9 10 11 Y=Input video Cb/Cr=0x80 Y=Input video Cb/Cr=0x80 Normal decode process No setup process Normal decode process No setup process Y=0x10 Cb/Cr=0x80 263 264 265 266 267 268 269 270 271 272 273 VBILENGTH [VBIL4:VBIL0] (3) VBIDEC-bit = 0 / HALFSU-bit = 1 / SETUP-bit = 0 (VBIDEC-bit = 0 / HALFSU-bit = 0 / SETUP-bit = 0) VBILENGTH [VBIL4:VBIL0] Normal decode process No setup process 524 525 1 2 3 4 5 Y=0x10 Cb/Cr=0x80 6 7 8 9 10 11 Y=0x10 Cb/Cr=0x80 Y=0x10 Cb/Cr=0x80 Normal decode process No setup process Normal decode process No setup process Y=0x10 Cb/Cr=0x80 263 264 265 266 267 268 269 270 271 272 273 VBILENGTH [VBIL4:VBIL0] (4) VBIDEC-bit = 1 / HALFSU-bit = 1 / SETUP-bit = 0 (VBIDEC-bit = 1 / HALFSU-bit = 0 / SETUP-bit = 0 VBILENGTH [VBIL4:VBIL0] ) Normal decode process No setup process 524 525 1 2 3 4 5 Y=0x10 Cb/Cr=0x80 6 7 8 9 10 11 Y=Input video Cb/Cr=0x80 Y=Input video Cb/Cr=0x80 Normal decode process No setup process Normal decode process No setup process Y=0x10 Cb/Cr=0x80 263 264 265 266 267 268 269 270 271 272 273 (5) VBIDEC-bit = 0 / HALFSU-bit = 0 / SETUP-bit = 1 VBILENGTH [VBIL4:VBIL0] VBILENGTH [VBIL4:VBIL0] Normal decode process Setup process (-7.5%) Rev.0 524 525 1 2 3 4 5 Y=0x10 6 7 54 8 9 10 11 Y=0x10 Normal decode process No Setup process 2003/01 ASAHI KASEI [AK8850] Y=Input video Cb/Cr=0x80 Y=Input video Cb/Cr=0x80 * 625 system VBIDEC-bit = 0 VBIDEC-bit = 1 Rev.0 55 2003/01 ASAHI KASEI [AK8850] Line-623.5 (from 429th pixel of Line-623) Line-5 Line-6 [VBIL4:VBIL0]-1.5 (till 429th pixel of Line-([VBIL4:VBIL0] - 2)) Y = 0x10 C = 0x80 Y = 0x10 C = 0x80 Y = Input video signal C = 0x80 1 [VBIL4:VBIL0] - 1.5 (from 430th pixel of Line-([VBIL4 VBIL0] - 2) Normal decode process Line-310 Line-311 Line-318.5 (till 429th pixel of Line-318) Y = 0x10 C = 0x80 Line-318.5 (from 430th pixel of Line-318) 311 + [VBIL4:VBIL0] - 1 311 + [VBI4:VBIL0] Line-623.5 (till 429th pixel of Line-623) Y = 0x10 C = 0x80 Y = Input video signal C = 0x80 2 Normal decode process (1) output code at VBIDEC-bit = 0 VBILENGTH [VBIL4:VBIL0] 622 Normal decode process 623 624 625 1 2 3 4 5 6 Normal decode process Y=0x10 Cb/Cr=0x80 Normal decode process Y=0x10 Cb/Cr=0x80 Normal decode process 310 311 312 313 314 315 316 317 318 VBILENGTH [VBIL4:VBIL0] (2) output code at VBIDEC-bit = 1 VBILENGTH [VBIL4:VBIL0] 622 Normal decode process 623 624 625 1 2 3 4 5 6 Y=Input video signal Cb/Cr=0x80 Normal decode process Y=0x10 Cb/Cr=0x80 Normal decode process Y=0x10 Cb/Cr=0x80 Y=Input video signal Cb/Cr=0x80 Normal decode process 310 311 312 313 314 315 316 317 318 VBILENGTH [VBIL4:VBIL0] Rev.0 56 2003/01 ASAHI KASEI [AK8850] 7-4-11 CLOSED CAPTION/CLOSED CAPTION EXTENDED DATA/VBID ( CGMS )/WSS It is possible to request decoding of Closed Caption, Closed Caption Extended Data, VBID and WSS signals by programming the [ REQUEST VBI INFORMATION REGISTER ]. The [ STATUS 2 REGISTER ] tells a host that data is detected and idecoding has been completed for a given decode request. Decoded data are written into the [ CLOSED CAPTION 1.2 REGISTER ], [ VBID 1.2 REGISTER ], [ WSS 1 REGISTER ] and [ WSS 2 & ASPECT DATA REGISTER ] respectively. The Closed Caption Data, Closed Caption Extended Data, VBID and WSS Data are encoded on each specified line respectively as listed below. Closed Caption : NTSC specified line 21st Line 284th Line Closed Caption Extended Data : NTSC specified line VBID ( CGMS Data ) : 525 system specified line 625 system specified line 20th Line / 238th Line 20th Line / 338th Line 23rd Line WSS ( 625 system only ) : 625 system specified line VBI Information Request Register : * [ REQUEST VBI INFO REGISTER ] bit 7 bit 6 bit 5 Reserved Reserved Reserved 0 0 0 bit 5 Reserved bit 4 bit 3 WSSRQ VBIDRQ Default Value 0 0 bit 4 WSS bit 3 VBID bit 2 EXTRQ 0 bit 2 EXT bit 1 CCRQ 0 bit 1 CC bit 0 ASPECTRQ 0 bit 0 ASPECT * [ STATUS 2 REGISTER ] bit 7 bit 6 APS1 APS0 * Read -out Line Number of the VBI information for each mode is as follows. Composite Closed Caption Extended Data VBID WSS NTSC(525 System) Component Y/C Betacam Line 21 Line 284 Line 20/Line 283 625 System MII Component Line 22 Line 335 Line 20/Line 333 Line 23 Rev.0 57 2003/01 ASAHI KASEI [AK8850] A procedure to read out each data is described here. Start [Request VBI Info Register] xxRQ-bit = 1 (Decode Request) If Closed Caption, then CCRQ-bit If VBID, then VBIDRQ-bit If WSS, then WSSRQ-bit [Status 2 Regsiter] Read (Check decode status bit) If xx-bit = 1 No If Closed Caption, then CC-bit If VBID, then VBID-bit If WSS, then WSS-bit If Closed Caption, then[Closed Caption 1 2 Register] If VBID, then [VBID 1 2 Register] If WSS, then [VBID 1 Register][WSS 2 & ASPECT Data Register] Yes Read Data Register READ OPERATION OF CLOSED CAPTION DATA : To read closed-caption data, write "1" to the CCRQ-bit. The AK8850 will enter a wait state for the Closed Caption data decoding. Upon receipt of the data, it is decoded and when decoding is completed, "1" is sent back to CC-bit of the [ STATUS 2 REGISTER ]. The CC-bit is usually at "1" right after a reset ( it becomes "0" by writing "1" at CCRQ-bit ). The decoded data is written into the [ CLOSED CAPTION 1.2 REGISTER ] as shown. Data in the [ CLOSED CAPTION 1.2 REGISTER ] is remains in this register until it is over-written. * [ CLOSED CAPTION 1 REGISTER ] bit 7 bit 6 bit 5 CC7 CC6 CC5 * [ CLOSED CAPTION 2 REGISTER ] bit 7 bit 6 bit 5 CC15 CC14 CC13 bit 4 CC4 bit 4 CC12 bit 3 CC3 bit 3 CC11 bit 2 CC2 bit 2 CC10 bit 1 CC1 bit 1 CC9 bit 0 CC0 bit 0 CC8 READ OPERATION OF CLOSED CAPTION EXTENDED DATA : Write "1" at EXTRQ-bit, which places the AK8850 into a wait state while Extended Data decoding occurs. The received data is decoded and after the decoding is completed,"1" is sent back to EXT-bit of the [ STATUS 2 REGISTER ]. EXT-bit is usually at "1" right after the reset ( it becomes "0" by writing "1" at EXTRQ-bit ). Then the decoded data is written into the [ EXTENDED DATA 1.2 REGISTER ] as shown. Data in the [ EXTENDED DATA 1.2 REGISTER ] remains in this register it is over-written. * [ EXTENDED DATA 1 REGISTER ] bit 7 bit 6 bit 5 EXT7 EXT6 EXT5 * [ EXTENDED DATA 2 REGISTER ] bit 7 bit 6 bit 5 EXT15 EXT14 EXT13 bit 4 EXT4 bit 4 EXT12 bit 3 EXT3 bit 3 EXT11 bit 2 EXT2 bit 2 EXT10 bit 1 EXT1 bit 1 EXT9 bit 0 EXT0 bit 0 EXT8 Rev.0 58 2003/01 ASAHI KASEI [AK8850] READ OPERATION OF VBID DATA To read the VBID data, write "1" to the VBIDRQ-bit. The AK8850 is put into a wait state while VBID data decodes. Received WSS data is decodecd and after the decoding is complete, "1" is sent back to VBID-bit of the [ STATUS 2 REGISTER ]. The VBID-bit is usually at "1" after a reset ( it becomes "0" by writing "1" at VBIDRQ-bit ). The decoded 13-bit data is then written into the [ VBID 1.2 REGISTER ] as shown. Data in the [ VBID 1.2 REGISTER ] is remains until it is over-written. * [ VBID 1 REGISTER ] bit 7 bit 6 VBID7 VBID8 * [ VBID 2 REGISTER ] bit 7 bit 6 Reserved Reserved bit 5 VBID9 bit 4 VBID10 bit 3 VBID11 bit 2 VBID12 bit 1 VBID13 bit 0 VBID14 bit 5 VBID1 bit 4 VBID2 bit 3 VBID3 bit 2 VBID4 bit 1 VBID5 bit 0 VBID6 READ OPERATION OF WSS DATA To read WSS data, write "1" to the WSSRQ-bit, The AK8850 is placed into a wait state while the WSS data decodes. Received WSS data is decoded and after the decoding is complete, "1" is sent back to WSS-bit of the [ STATUS 2 REGISTER ].WSS-bit is usually at "1" right after the reset ( it becomes "0" by writing "1" at WSSRQ-bit ). Then the decoded data is written into the [ WSS 1 REGISTER ] and [ WSS 2 & ASPECT DATA REGISTER ] as shown. Data in the [ WSS 1 REGISTER ] and [ WSS 2 & ASPECT DATA REGISTER ] is remains until it is over-written. * [ WSS 1 REGISTER ] bit 7 bit 6 G2-7 G2-6 bit 5 G2-5 bit 4 G2-4 bit 3 G1-3 bit 2 G1-2 bit 1 G1-1 Bit 0 G1-0 * [ WSS 2 & ASPECT DATA REGISTER] bit 7 bit 6 bit 5 ASPECT Reserved G4-13 bit 4 G4-12 bit 3 G4-11 bit 2 G3-10 bit 1 G3-9 bit 0 G3-8 7-4-12 VIDEO ASPECT SIGNAL This command detects the Video Aspect signal ( refer to the following diagram ) that is superimposed on Line 16 and Line 279 of the Composite signal. The Aspect signal detection is performed by making a decode request which is set by the [ REQUEST VBI INFO REGISTER ]. After the decoding is completed, a decode complete notification is generated. The decode data is written into the Aspect-bit of the [ WSS 2 & ASPECT DATA REGISTER ].Aspect-bit data remains until it is over-written. Video Aspect Signal Outline Input signal : Composite signal only ( at NTSC / YC input only ) Line : 16th Line and 279th Line Level : 70 +/- 25 IRE Rising Edge Point : 12.5 +/- 3.2 microsec from HSYNC rising edge ( at 50 % point ) Falling Edge Point : 58.9 +/- 3.2 microsec from HSYNC falling edge ( at 50 % point) Aspect Bit : Wide at "1" Normal at "0" 70+/-25 IRE 50% 50% 12.5+/-3.2usec 58.9+/-3.2usec 50% Rev.0 59 2003/01 ASAHI KASEI [AK8850] Video Aspect Related Registers : * [ REQUEST VBI INFO REGISTER ] bit 7 bit 6 bit 5 Reserved Reserved Reserved 0 0 0 bit 4 bit 3 WSSRQ VBIDRQ Default Value 0 0 bit 2 EXTRQ 0 bit 1 CCRQ 0 bit 0 ASPECTRQ 0 * [ STATUS 2 REGISTER ] bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 APS1 APS0 Reserved WSS VBID EXT CC ASPECT A decoding request of the Video Aspect signal, superimposed on the input signal is done by writing "1" to the ASPECTRQ-bit of the [ REQUEST VBI INFO REGISTER ]. The AK8850 is put into a wait state for data decoding. A decode complete signal is sent back to the [ STATUS 2 REGISTER ]. The decoded data is written into the [ WSS 2 & ASPECT DATA REGISTER ]. * [ WSS 2 & ASPECT DATA REGISTER ] bit 7 bit 6 bit 5 ASPECT Reserved G4-13 Aspect-bit =0 : Normal signal Aspect-bit =1 : Wide signal A Video Aspect decode request signal should be made only when NTSC Composite or Y/C signals are input. If a decoding request is made with the 525 Component input, decoding is actually done as in the Composite signal input case. In this case no Video Aspect signal exists in the signal and resulting data is meaningless. If a decoding request is made with the 625 Component input, it is ignored and the request bit is kept at "1" ). 7-4-14 DIGITAL PIXEL INTERPOLATOR A digital Pixel Interpolator is equipped in order to align Pixels in the Vertical direction. ON / OFF / AUTO modes of the interpolator is selectable by the [ CONTROL 1 REGISTER ] setting. If the Auto mode is selected, the ON / OFF state of the interpolator is automatically set by the clock mode used as follows. Line-locked mode : OFF Frame-locked mode : ON External clock mode : ON Pixel Interpolator Related Registers : * [ CONTROL 1 REGISTER ] bit 7 bit 6 bit 5 FRCSYNC Reserved INTPOL1 1 0 0 bit 4 bit 3 INTPOL0 AGCC1 Default Value 0 0 bit 2 AGCC0 0 bit 1 AGCT1 0 bit 0 AGCT0 0 bit 4 G4-12 bit 3 G4-11 bit 2 G3-10 bit 1 G3-9 bit 0 G3-8 * INTOL1 : INTOL0-bit set INTPOL1:INTPOL0 00 01 10 11 Pixel Interpolator Auto ON OFF Reserved In Auto mode, ON / OFF states of the interpolator are selected by the clock mode used. The interpolator mode selection is not affected by the types of input signals ( same for 525 line and 625 line systems ). Rev.0 60 2003/01 ASAHI KASEI [AK8850] 7-4-15 NON-SIGNAL INPUT DETECTION The AK8850 detects non-signal input conditions and, when detected, outputs a Black level signal ( Y=0x10,Cb/Cr=0x80 ). The non-signal input condition is detected by checking for the existence of the VSYNC signal. In order to have higher margin against non-Standard signal inputs, the non-signal detection is made only when the VSYNC is not detected two or more consecutive times. The result is output via the NSIG output pin. Output State: NSIG=1 ( non-signal input ) NSIG=0 ( valid input signal ) 7-4-16 STANDARD SIGNAL DETECTION The AK8850 has a Standard Signal Detection function. When a non-Standard input signal is detected, the NSTD output pin changes to " high ". The NSTD output becomes " low " (Standard signal input ) when either ( a ) or ( b ) conditions below are met. ( a ) with Component input ( 525 / 625 ), the Frame configuration during the past 2 Frames is made with ODD / EVEN or EVEN / ODD sequence. ( b ) with Composite input ( including Y/C input ), the SCH phase is within +/- 67.5 degrees and the Frame configuration is made with ODD / EVEN or EVEN / ODD sequence. 7-4-17 OUTPUT FORMAT ( 601 FORMATTER ) The AK8850 outputs the decoded data in ITU-R BT.601 compatible format ( Y/Cb/Cr 4:2:2 ). The min. and max. values of the output code are selectable by 601LIMIT-bit of the [ OUTPUT FORMAT REGISTER ]. At 601LIMIT-bit = 0 Y : 1 ~ 254 Cb/Cr : 1 ~ 254 Y : 16 ~ 235 At 601LIMIT-bit = 1 Cb / Cr : 16~ 240 Output Format Related Register : bit 7 bit 6 bit 5 ACTSTA[2] ACTSTA[1] ACTSTA[0] bit 4 YCDELAY[2] bit 3 YCDELAY[1] bit 2 YCDELAY[0] bit 1 601LIMIT bit 0 ERRHND 0 0 0 Default Value 0 0 0 0 0 Rev.0 61 2003/01 ASAHI KASEI [AK8850] 7-4-18 SETUP Enabling and Disabling SETUP is selected by the [ INPUT VIDEO STANDARD REGISTER ]. When the SETUP-bit is "1", internal signal processing is performed, assuming that the SETUP signal is input. This signal is processed outside of the VBI period. The VBI period is set by the [ VERTICAL BLANKING LENGTH REGISTER ]. Signal Set Register with SETUP Features : When the input signal contains a SETUP command, set [ SETUP ]-bit of the [ INPUT VIDEO STANDARD REGISTER ] to "1". * Input Video Standard Register bit 7 Reserved bit 6 NENT bit 5 B/W bit 4 SETUP bit 3 VS3 Default Value bit 2 VS2 bit 1 VS1 bit 0 VS0 0 0 0 0 0 0 0 0 * SETUP-bit Set SETUP-bit 0 1 Setup without Setup with Setup Note Setup process should be done exclusive the term of VBI interval. Setting is not affected by input signal types ( Composite, YC and Component signals ). When the SETUP-bit is set at "1", the following conversion is performed on input signal. On 286 mV SYNC system signals (NTSC Composite, YC signal, Betacam signal ) with SETUP, Luminance signal ( Y ) : Y = ( Y- 42 ) / 0.925 ; Chroma signal ( U / V ) : Pb = Pb / 0.925 ; Pr = Pr / 0.925 ; On 300 mV SYNC systems ( MII signal ) with SETUP , Luminance signal ( Y ) : Y = ( Y-41 ) / 0.925 ; Chroma signal ( U / V ) : Pb = Pb / 0.925 ; Pr = Pr / 0.925 ; Rev.0 62 2003/01 ASAHI KASEI [AK8850] 7-4-19 TIMING OUTPUT The AK8850 outputs the signals listed below. Output logical states can be altered by the [ OUTPUT CONTROL REGISTER ]. The state shown is the default value (refer to the Output Timing Diagram ). Either the VSYNC or VD signals can be output on the VSYNC output pin per the register setting. Output timing of the Field signal and the Frame signal can be delayed by 0.5 H time using the FFDELAY-bit of the [ OUTPUT CONTROL REGISTER ]. CSYNC signals can be output via the FRAME1 pin by setting the FRCSYNC-bit of the [ CONTROL 1 REGISTER ] bit-7. FFDELAY-bit 0 1 FRCSYNC-bit 0 1 Function FIELD/FRAME timing signal changes at the falling edge of HSYNC of proper line. FIELD/FRAME timing signal chages at the raising edge of serration pulse of proper line. Function Frame timing signal is output from FRAME1pin CSYNC timing signal is output from FRAME1pin At 525-Line-System input ( output state at default value ) HSYNC : " low " level signal of 4.7 microsec. Duration in 15.734 KHz interval VSYNC : " low " output signal during Line 4 ~ Line 6 / Line 266.5 ~ Line 269.5 ( Line 266.5 means from the latter 0.5 H time of Line 266,and Line 269.5 means up to the former 0.5 H time of Line 269 ). VD : " low " output signal during Line1 ~ Line 9 / Line263.5 ~ Line 272.5 ( Line 263.5 means from the latter 0.5 H time of Line 263, and Line 272.5 means up to the former 0.5 H time of Line 272 ). FIELD : Output signal to become " low " at Odd Fields, and " high " at Even Fields. FRAME : Color Frame For non-Standard signal inputs, Field signal toggles at the rate of ( Line numbers per each Frame / 2 ). Frame signal changes at the rate of Line numbers per each Frame ( Frame signal changes state at Line 4 ). CSYNC : Composite Sync signal.CSYNC output does not change state. At 625-Line-System input ( output state at default value ) HSYNC : " low " level signal of 4.7 microsec. duration in 15.734 KHz interval VSYNC : " low " output signal during Line 1 ~ Line 3.5 / Line 313.5 ~ Line 315 ( Line 3.5 means up to the former 0.5 H time of Line 3,and Line 313.5 means from the latter 0.5 time of Line 313 ). VD : " low " output signal during Line 623.5 ~ Line 5 / Line 311 ~ Line 318.5. ( Line 632.5 means from the the latter 0.5 H time of Line 623, and Line 318.5 means up to the former 0.5 H time of Line 318 ). FIELD : Output signal to become " low " on Odd Fields, and " high " on Even Fields. FRAME : Color Frame For non-Standard signal inputs, Field signal toggles at the rate of ( Line numbers per each FRAME / 2 ). Frame signal changes state at the rate of Line numbers per each Frame ( Frame signal changes state at Line 1 ). CSYNC : Composite Sync signal. CSYNC output does not change state Data at both rising edge and falling edge of the FIELD signal is Cb data. The FIELD signal and data relationship of Standard signal inputs is as follows. FIELD D[7:0] Cb Y Cr Y 122T Cb Cb0 Y0 Cr0 Y1 Rev.0 63 2003/01 ASAHI KASEI [AK8850] * [ OUTPUT CONTROL REGISTER ] bit 7 bit 6 bit 5 VDVSYNC FFDELAY HALFCLK bit 4 bit 3 bit 2 bit 1 FRAME DVALVLK FEILD VSYNC Default Value 0 0 0 1 0 1 0 Logical state can be altered by these registers. Default value is " 0 " as shown in the timing diagram. bit 4 bit 3 INTPOL0 AGCC1 Default Value 1 0 0 0 0 FRCSYNC-bit controls output on FRAME 1 pin. * [ CONTROL 1 REGISTER ] bit 7 bit 6 bit 5 FRCSYNC DECIMAT INTPOL1 bit 2 AGCC0 0 bit 1 AGCT1 0 bit 0 HSYNC 0 bit 0 AGCT0 0 7-4-20 VLOCK FUNCTION The AK8850 synchronizes its internal operation with the input signal's FRAME configuration. For example, if the input signal Frame configuration consists of 525 lines, the internal operation uses the 525 Line configuration. This is called the VLOCK configuration. When the input signal configured with 525 Line per Frame is switched to 524 Lines, the operation tracks to the switched input signal system. In this case VLOCK function is put into un-locked state during the tracking time. The un-locked state is verified by the [ STATUS 1 REGISTER ]. VLOCK status is observed on the DVALID pin by setting the DVAL / VLK-bit of the [ OUTPUT CONTROL REGISTER ] ( R / W ) [ SUB ADDRESS 0x05 ]. VLOCK Status Locked (synchronaize with Input video signal) UnLocked Un-synchronaized with input video signal Status 1 Register VLOCK-bit 1 0 VLOCK output pin High Low The transition timing of the VLOCK output pin changes with VLOCK configuration conditions. . Rev.0 64 2003/01 ASAHI KASEI [AK8850] 7-4-21 OUTPUT INTERFACE The AK8850 outputs decoded data in ITU-R BT.656 compatible interface formats, i.e., The sample number for each Line is guaranteed to be 858 / 864 ( 525 system / 625 system ) respectively. Poor input quality or non Line-locked/Frame-locked PLL clocks may prevent ITU-R BT.656 compatible output. , In these cases, the Input signal and Output data are correlated by the following 2 methods, selected by the [ OUTPUT FORMAT REGISTER ]. ( 1 ) Adjust using a Line-Drop / Repeat scheme ( number of Lines is not equal to 525 / 625, but number of samples is guaranteed to be 858 / 864 ). This process is performed when the final stage output buffer of the device either overflows or underflows. ( 2 ) Make 858 / 864 samples to be variable ( number of samples is not equal to 858 / 864, but number of Lines is guaranteed to be 525 / 625 ). Decoded data becomes ITU-R BT.656 compatible except for the last line of each Frame ( Line 3 in 525 system , Line 625 in 625 system ).i.e., typical 858 / 864 samples per each line is guaranteed other than at Line 3 / Line 625 ( 525 system / 625 system ). The number of samples at Line 3 and Line 625 is un-determined since it is decided by relationdhip between the input signal rate and the PLL-generated clock rate (it hovers around 858 / 864 samples ). In this processing mode, there is less of a chance for buffer overflow or underflow since the buffer pointer is moved to the mid point of the buffer at the last line. When either overflow or underflow occurs at the final stage buffer, a Line Drop / Repeat function is processed ( which can occur when the input signal rate differs much from the PLL-generated clock rate ). The DVALID pin output is " low " during the Active-Video period of the output data. Relationship between HSYNC, DVALID and output data are shown below. Video Signal HSYNC DVALID CLK27MOUT D[7:0] Cb0 Y0 Cr0 Y1 Cb1 Y2 Cr1 Y3 Y718 Cr359 Y719 Active Video Start position Normally, 123th/133th(525 system/625 system)pixel from 0H pixel Fine-tuning the Active-Video start position and a Y / C Delay amount to be output can be accomplished by programming the [ OUTPUT FORMAT REGISTER ]. Rev.0 65 2003/01 ASAHI KASEI [AK8850] Output Interface Set Register : Output Interface is set by the [ OUTPUT FORMAT REGISTER ]. * [ OUTPUT FORMAT REGISTER ] bit 7 ACTSTA[2] bit 6 ACTSTA[1] bit 5 ACTSTA[0] bit 4 YCDELAY[2] bit 3 YCDELAY[1] Default Value bit 2 YCDELAY[0] bit 1 601LIMIT bit 0 ERRHND 0 0 0 0 0 0 0 0 [ ERRHND ]-bit of the [ OUTPUT FORMAT REGISTER ] controls error handling as follows. * ERRHND-bit ERRHND-bit 0 1 Number of sample is constant Number of line in a frame is constant 525 System : 858 samples 625 System : 864 samples 525 System : 525Line 625 System : 625Line Fine-tuning of the start position is accomplished by programming the ACTSTA [2 :0 ]-bit. 0H point 122th sample (525 System) 132th sample (625 System) * ACTSTA [ 2 : 0 ]-bit set ACTSTA2:ACTSTA0 Function Note 100 101 110 111 000 001 010 011 525system : Active Video starts at the 119th sample 625system : Active Video starts at the 129th sample 525system : Active Video starts at the 120th sample 625system : Active Video starts at the 130th sample 525system : Active Video starts at the 121th sample 625system : Active Video starts at the 131th sample 525system : Active Video starts at the 122th sample 625system : Active Video starts at the 132th sample 525system : Active Video starts at the 123th sample 625system : Active Video starts at the 133th sample 525system : Active Video starts at the 124th sample 625system : Active Video starts at the 134th sample 525system : Active Video starts at the 125th sample 625system : Active Video starts at the 135th sample 525system : Active Video starts at the 126th sample 625system : Active Video starts at the 136th sample default a fine-tuning of the YC output timing is possible by setting YC delay [ 2 : 0 ]-bit of the [ OUTPUT FORMAT REGISTER ].The YC delay fine-tuning bit is set in 2's complement values. ACTSTA2:ACTSTA0 Function Note 100 Y data is delayed 4samples (296nsec) agaist C-data 101 Y data is delayed 3samples (222nsec) agaist C-data 110 Y data is delayed 2samples (148nsec) agaist C-data 111 Y data is delayed 1sample (74nsec) agaist C-data 000 No delay Default 001 C data is delayed 1sample (74nsec) agaist Y-data 010 C data is delayed 2samples (148nsec) agaist Y-data 011 C data is delayed 3samples (222nsec) agaist Y-data Rev.0 66 2003/01 ASAHI KASEI [AK8850] 7-4-22 POWER SAVE MODE The AK8850 is placed in Power Save mode by setting the PS-bit of the [ POWER SAVE MODE REGISTER ] to " 1 ". Exiting Power Save mode is done by setting the PS-bit to "0". During Power Save mode, the I2C bus controller, clock output driver and VREF generating circuit are active, the PLL block is initialized and PLL DAC local code becomes 0x80. After exiting Power Save mode, the device re-starts operation from the state which is set via the I2C bus. All circuits are put into Sleep mode when the Power Down pin ( PD ) is set to high. The IVCXO output current is zero micro Amps in this state. To re-start the AK8850, an input reset and initialization are required after setting PD pin from high to low. Operation is stabilized in a few milliseconds. Please follow the Power Down set sequence for proper setting. Power Save Mode Related Register : Power Save related registers are programmed by the [ POWER SAVE MODE REGISTER ]. * [ POWER SAVE MODE REGISTER ] bit 7 bit 6 bit 5 Reserved Reserved Reserved 0 * PS-bit set PS-bit 0 1 0 0 bit 4 bit 3 PLLRST ADC3 Default Value 0 0 bit 2 ADC2 0 bit 1 ADC1 0 bit 0 PS 0 Function Normal function Stops the clock supply to the Internal digital Block, exclusive control block.. Stops ADC1/2/3. Resets the PLL control circuit. Note * ADC1 / 2 / 3-bit set ADC1/2/3-bit 0 1 Function ADC1/2/3 Active mode ADC1/2/3 sleep mode Note Each ADC can be set to sleep mode individually. Rev.0 67 2003/01 ASAHI KASEI [AK8850] 7-4-23 DEVICE CONTROL INTERFACE The AK8850 is controlled via the I2C bus interface. I2C Control Sequence Slave Address is selected to be either 0x88 or 0x8A by SELA pin set. SELA Slave Address Pull down(L) 0x88 Pull up(H) 0x8A Write Sequence: S Slave Address W A Sub Address A Data_1 A Data_n A/A Stp Sequential Read: S Slave Address W A Sub Address A rS Slave Address R A DATA1 A DATA2 A DATA A DATA n A Stp S,(rS) : Start Condition A : Acknowledge (SDA LOW) A : Not Acknowledge (SDA HIGH) Stp : Stop Condition R/W 1 : Read 0 : Write by Host by AK8850 Rev.0 68 2003/01 ASAHI KASEI [AK8850] 8. REGISTER DEFINITION The AK8850 has the following registers. Sub Address 0x00 0x01 0x02 0x05 0x06 0x08 0x09 0x0A 0x0B 0x0C 0x0D 0x0E 0x0F 0x10 0x11 0x12 0x13 0x14 0x15 0x1C 0x1F 0x20 0x21 0x22 0x23 0x24 0x25 0x26 0x27 0x28 0x29 0x2E 0x36 0x37 0x38 0x39 0x3A 0x46 0x47 Register Input Video Standard Register Input Signal Select Register Vertical Blanking Length Register Output Control Register Output Format Register Control-1 Register Control-2 Register Clamp Control Register Clamp Timing Control Register Clamp Timing 2 Control Register PGA1 Gain Control Register PGA2 Gain Control Register PGA3 Gain Control Register Y/C Separation Control Register Color Killer Control Register Brightness Control Register Contrast Control Register Saturation Control Register HUE Control Register Power Save Register Request VBI Info Register Status 1 Register Status 2 Register Closed Caption1 Register Closed Caption2 Register Extended Data 1 Register Extended Data 2 Register VBID1 Register VBID2 Register WSS1 Register WSS2 & Aspect Data Register Device/Revision ID Register Clock Control-1 Register Clock Control-2 Register Clock Control-3 Register Clock Control-4 Register Clock Control-5 Register PLL Control Register PLL DAC Set Register Default 0x00 0x11 0x14 0x14 0x00 0x80 0xC1 0x00 0x11 0x1C 0x40 0x40 0x40 0x06 0xAD 0x00 0x80 0x80 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x84 0x7C 0x3C 0xDC 0x04 0x00 0x80 R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W W R R R R R R R R R R R R/W R/W R/W R/W R/W R/W R/W Function Set Input Video Standard Select Input Video signal Set VBI Interval Set the attribution of output data Set the output I/F Control Register Control Register Set the clamp function setting Set the clamp pulse timing Set the clamp pulse timing Set the manual Gain of PGA1 Set the manual Gain of PGA2 Set the manual Gain of PGA3 Set the YC Separation function Color killer setting Set Brightness adjustment Set Contrast adjustment Set Saturation adjustment Set HUE adjustment Power Save setting VBIDdata decode requet Internal status of AK8850 nternal status of AK8850 Closed Caption data Closed Caption data Closed Caption Extended data Closed Caption Extended data VBID data VBID data WSS data WSS data and video aspect data. Device ID / Revision ID Clock transition control register. Clock transition control register. Clock transition control register. Clock transition control register. Clock transition control register. PLL Control Register PLL_DAC Setting register Rev.0 69 2003/01 ASAHI KASEI [AK8850] INPUT VIDEO STANDARD REGISTER ( R / W )[ SUB ADDRESS 0x00 ] This register sets the input video signal Standard. Automatic setup recognition is not available. Reserved Bits must be set to " 0 ". Sub Address 0x00 bit 7 bit 6 Reserved NENT 0 0 Default Value : 0x00 bit 1 bit 0 VS1 VS0 0 0 bit 5 B/W 0 bit 4 bit 3 SETUP VS3 Default Value 0 0 bit 2 VS2 0 Input Video Standard Register Definition BIT Register Name R/W Definition Set the input video standard VS3 VS0 0000 : NTSC/ 525Component 1111 : 625Component AK8850 can deal with only component signal for 625- video ssytems. Other settings are reserved. 0 : without Setup [Default] 1 : with Setup B/W video signal setting 0 : Color video signal is input [Default] 1 : B/W video signal is input Set the Component Video Signal 0 : MII Level Component Video signal [Default] 1 : BETACAM Level component video signal Reserved bit R/W bit 0 ~ bit 3 VS0 ~ VS3 Video Standard bit bit 4 bit 5 SETUP B/W Setup bit Black & White bit R/W R/W R/W bit 6 bit 7 NENT Reserved Component Video Sel bit Reserved bit R/W Setting Component input is done as follows. 1. Component input is selected via the input signal select register. 2. Selection of MII or Betacam is done by the Input Video Standard Register NENT-bit. 3. Set either 525- or 625 line systems. Rev.0 70 2003/01 ASAHI KASEI [AK8850] INPUT SIGNAL SELECT REGISTER ( R / W ) [ SUB ADDRESS 0x01 ] Register to select the input signal. Sub Address 0x01 bit 7 bit 6 Reserved Reserved 0 0 Default Value : 0x11 bit 1 bit 0 INSEL1 INSEL0 0 1 bit 5 SYNCIN1 0 bit 4 bit 3 SYNCIN0 INSEL3 Default Value 1 0 bit 2 INSEL2 0 Input Select Register Definition BIT Register Name bit 0 ~ bit 3 INSEL0 ~ INSEL3 R/W Input Select bit R/W bit 4 ~ bit 5 SYNCIN0 SYNCIN Select bit SYNCIN1 R/W Definition Select the Input video signal INSEL3 INSEL0 0000 : No Input 0001 : AIN1 Composite [Default] 0010 : AIN2 Composite 0011 : AIN3 Composite 0110 : AIN2 Y AIN4 C 0111 : AIN3 Y AIN5 C 1011 : AIN3 Y AIN5 U AIN6 V Select the video signal for the Clamp timing generator. SYNC1: SYNC0 00 : No Input 01 : SYNC1 timing [Default] 10 : SYNC2 timing 11 : SYNC3 tiimng Reserved bit bit 6 Reserved bit 7 Supplement bit3 - bit0 bit3=1: component , bit2=1: Y/C Video input Reserved bit R/W Rev.0 71 2003/01 ASAHI KASEI [AK8850] VERTICAL BLANKING LENGTH REGISTER ( R / W ) [ SUB ADDRESS 0x02 ] Register to set VBI interval. Sub Address 0x02 bit 7 bit 6 VBIDEC TRSVSEL 0 0 bit 5 HALFSU 0 bit 4 bit 3 VBIL4 VBIL3 Default Value 1 0 bit 2 VBIL2 1 Default Value : 0x14 bit 1 bit 0 VBIL1 VBIL0 0 0 Vertical Blanking Register Definition BIT Register Name bit 0 bit 4 VBIL4 VBIL0 Vertical blanking Length bit Information R/W R/W Definition Set the VBI interval Default value is 20 (decimal) i.e., Active video starts from Line-21 The value of VBI[4:0] must be set more than 10. Set the setup function for the first active line of the 2nd field. 0 : 0.5H of 2nd field is not made setup process. 1 : 0.5H of 2nd field is made setup process. Set the V-bit transition timing for EAV/SAV. NTSC, 525 Component TRSVSEL = 0 : Line 1-9 / Line264-Line272 : V=1 Other V=0 TRSVSEL = 1: Line 1-19 / Line 264-Line282 V=1 Other V=0 625 Sytem : V-bit setting should reflect TRSVSEL-bit setting Output data while the VBI Interval. 0 : Y = 0x10 C = 0x80 1 : Y = input data(same as B/W process) C = 0x80 bit 5 HALFSU Half Setup bit R/W bit 6 TRSVSEL Time Reference Signal V Select bit R/W bit 7 VBIDEC VBI Decode bit R/W For details, please refer to section 7-4-10 VERTICAL BLANKING INTERVAL. Rev.0 72 2003/01 ASAHI KASEI [AK8850] OUTPUT CONTROL REGISTER ( R / W ) [ SUB ADDRESS 0x05 ] Thie register sets the external output signal attributes like HSYNC, VSYNC, FIELD, DVALID and FRAME etc. Timing of output signals can be altered by CLKOUT-bit set. Sub Address 0x05 bit 7 bit 6 VDVSYNC FFDELAY 0 0 bit 5 HALFCLK 0 bit 4 bit 3 FRAME DVALVLK Default Value 1 0 bit 2 FIELD 1 Default Value : 0x14 bit 1 bit 0 VSYNC HSYNC 0 0 Output Control Register Definition BIT Register Name bit 0 bit 1 bit 2 bit 3 bit 4 bit 5 bit 6 HSYNC VSYNC FIELD DVAL/VLK FRAME HALFCLK FFDELAY HSYNC-Logic bit VSYNC-Logic bit FIELD-Logic bit DVALID VLock Switch- bit FRAME-Logic bit HALFCLK-bit Field Frame Delay bit R/W R/W R/W R/W R/W R/W R/W R/W bit 7 VDVSYNC VD/VSYNC Select bit R/W Definition 0 : Low [default] 1 : High 0 : Low[default] 1 : High 0 : ODD FIELD : Low 1 : ODD FIELD : High [default] 0 : DVALID signal output [default] 1 : VLOCK status output 0 : Low at CF = 0 1 : High at CF = 0[default] 0 : Low at Y-data ouput timing [ Default] 1 : Hight at Y-data output Field timing signal and Frame timing signal can be output 0.5H delayed with this bit. 0 : No Delay [default] 1 : 0.5H Delay 0 : Output VSYNC Pulse [default] 1 : Ouput VD pulse. (Refer to the Figure "Output timing Signal") FIELD and FRAME signals are correct values only when the Standard signal is input. ( in case of Non-Standard signal input, FIELD and FRAME signals are not necessarily correct ones .For handling of Non-Standard signal input,refer to item 7-4-21 ). Rev.0 73 2003/01 ASAHI KASEI [AK8850] OUTPUT FORMAT REGISTER ( W / R ) [ SUB ADDRESS 0x06 ] Register to set output format. Sub Address 0x06 bit 7 bit 6 ACTSTA2 ACTSTA1 0 0 bit 5 ACTSTA0 0 bit 4 bit 3 YCDELAY2 YCDELAY1 Default Value 0 0 bit 2 YCDELAY0 0 Default Value : 0x00 bit 1 bit 0 601LIMIT ERRHND 0 0 Output Format Register Definition BIT Register Name R/W R/W bit 0 ERRHND Error Handling bit bit 1 601LIMIT 601 Output Limit bit R/W R/W bit 2 ~ bit 4 Y/C Delay Control bit YCDELAY0 YCDELAY2 Active Video Start Control bit R/W bit 5 ~ bit 7 ACTSTA0 ACTSTA2 Definition Setting the data handling procedure when AK8850 cannot output the data follow to ITU-R. Bt.656. Error handling normally occurs within the last lines of the Frame. 0 : Line Drop/Repeat 1 : Number of Smaples of the line is change. Min/Max value of the output data 0 : 1~254 (Y/Cb/Cr) [Default ] 1 : 16~235 (Y) 16~240 (Cb/Cr) Y/C delay setting for output data. One delay time is 74nsec(1clock@13.5MHz) Set the value with 2's complement [YCDELAY2-YCDELAY0]= 101 : Y-data is 3clocks delay against C-data 110 : Y-data is 2clocks delay against C-data 111 : Y-data is 1clock delay against C-data 000 : No delay [Default] 001 : C-data is 1clock delay against Y-data 010 : C-data is 2clocks delay against Y-data 011 : C-data is 3clocks delay against Y-data Set fine adjustment of Start position of decoded video data. Set the value with 2's complement [ACTSTA2:ACTSTA0]= 101 : Decoding the video data 3pixels earlier. 110 : Decoding the video data 2pixels earlier. 111 : Decoding the video data 1pixel earlier. 000 : Normal position [Default] 001 : Decoding the video data 1pixel delayed. 010 : Decoding the video data 2pixels delayed. 011 : Decoding the video data 3pixels delayed. Rev.0 74 2003/01 ASAHI KASEI [AK8850] CONTROL 1 REGISTER / CONTROL 2 REGISTER These registers control the AK8850 operations. There are 2 registers, CONTROL 1 and CONTROL 2. Reserved bits must be set to " 0 ". Control 1 Register (R/W) [Sub Address 0x08] Sub Address 0x08 bit 7 bit 6 FRCSYNC Reserved 1 0 Default Value : 0x80 bit 1 bit 0 AGCT1 AGCT0 0 0 bit 5 INTPOL1 0 bit 4 bit 3 INTPOL0 AGCC1 Default Value 0 0 bit 2 AGCC0 0 Control 1 Register Definition BIT Register Name R/W bit 0 ~ bit 1 AGCT0 ~ AGCT1 AGC Time Constant Control bits R/W bit 2 ~ bit 3 AGCC0 ~ AGCC1 AGC Coring Control bits R/W bit 4 ~ bit 5 INTPOL0 INTPOL1 Interpolator Control bit R/W Definition Set the AGC time constant. When the AGC is Disabled, each PGA can be set manually. [AGCT1 AGCT0] = 00 : Disable [default] 01 : Fast [T = 1Field] 10 : Middle [T = 7Field] 11 : Slow [T = 29Field] (T : Time constance) Set the non-sensing bandwidth of AGC [AGCC1 AGCC0] = 00 : No non-sensing bandwidth[Default] 01 : 1bit 10 : 2bits 11 : 3bits Setting for Pixel Interpolator [INTPOL1 INTPOL0] = 00 : Auto [Default ] 01 : ON 10 : OFF 11 : Reserved Setting to Automode, the Interpolator switch turns on/off according to the clock mode as described bellow, Line Lock PLL : OFF Frame Lock PLL: ON Fixed Clock mode: ON Reserved Define the output data from FRAME1pin. 0 : FRAME timing pulse output 1 : CSYNC timing pulse output [default] bit 6 bit 7 Reserved FRCSYNC Reserved Frame CSYNC switch bit R/W R/W Rev.0 75 2003/01 ASAHI KASEI [AK8850] Control 2 Register (R/W) [Sub Address 0x09] Sub Address 0x09 bit 7 bit 6 bit 5 bit 4 bit 3 CLKMODE0 ACC1 ACC0 DPCC1 CLKMODE1 Default Value 1 1 0 0 0 Control 2 Register Definition BIT Register Name bit 2 DPCC0 0 Default Value : 0xC1 bit 1 bit 0 DPCT1 DPCT0 0 1 R/W bit 0 ~ bit 1 DCPT0 ~ DPCT1 Digital Pedestal Clamp Timing bit R/W bit 2 ~ bit 3 DPCC0 ~ DPCC1 Digital Pedestal Clamp Coreing bit bit 4 ~ bit 5 ACC0 ~ ACC1 Auto Color Control bits R/W bit 6 ~ bit 7 CLKMODE0 ~ CLKMODE1 Clock Mode bits R/W Definition Setting of TIme constant of the digital pedestal clamp. DPCT1:DPCT0 00 : digital pedestal clamp OFF 01 : Fast [Default] 10 : Middle 11 : Slow Setting the non-sensing bandwidth of digital pedestal clamp. DPCC1 : DPCC0 00 : No non-sensing bandwidth [Default] 01 : 1bit 10 : 2bits 11 : 3bits Setting the ACCf function [ACC1 ACC0] = 00 : Disable ACC [Default] 01 : Fast [T = 2-Field] 10 : Middle [T = 8-Field] 11 : Slow [T = 30-Field] (T : Time constance) Setting Clock mode CLKMODE1: CLKMODE0 = 00 : Fixed clock mode(27MHz) 01 : Line-Locked Clock mode 10 : Frame-Locked Clock mode 11 : Clock mode Auto Select mode [Default] Rev.0 76 2003/01 ASAHI KASEI [AK8850] CLAMP CONTROL REGISTER ( R / W ) [ SUB ADDRESS 0x0A ] This register controls clamp-related matters. Reserved bits must be set to " 0 ". Sub Address 0x0A bit 7 bit 6 UNMASK Reserved 0 0 bit 5 ACLMP 0 bit 4 Bit 3 INCLPTMG FBCLPTMG1 Default Value 0 0 bit 2 FBCLPTMG0 Default Value : 0x00 bit 1 bit 0 CLPLVL1 CLPLVL0 0 0 0 Clamp Control Register BIT Register Name R/W bit 0 bit 1 CLPLVL0 ~ CLPLVL1 CLAMP Level 0 ~ CLAMP Level1 bit R/W Definition Setting analog video clamp. This setting is valid for Clamp 1. The level of Clamp 2/3 is constant at 512 level. CLPLVL1 CLPLVL0 00: 16 [default] 01: 240 10: 252 11: Analog clamp is off Setting the clamp timing pulse. 00 : Synctip level clamp with the internal clamp timing [default] 01 : Synctip level clamp with the external clamp timing pulse. 10 : Pedestal level clamp with the internal clamp timing pulse. 11 : Pedestal level clamp with the external clamp timing pulse. Setting the clamp timing pulse. 0 : Internal Clamp timing pulse [default] 1 : External Clamp timing pulse Setting the clamp on/off. When a video signal is input through AC coupling capacitor, this set must be set to "0". 0 : ON [default] 1 : OFF (AIN Clamp OFF) Reserved Clamp mask on/off bit. Normally this bit set to 0. 0 : Masked [default] 1 : Unmasked bit 2 bit 3 FBCLPTMG0 ~ FBCLPTMG1 Feed Back Clamp Timing bit R/W bit 4 INCLPTMG Input Clamp Timing bit bit 5 ACLAMP Analog Clamp On/Off bit R/W R/W R/W bit 6 bit 7 Reserved UNMASK Reserved bit Clamp Unmask bit Rev.0 77 2003/01 ASAHI KASEI [AK8850] CLAMP TIMING 1 CONTROL REGISTER ( R / W ) [ SUB ADDRESS 0x0B ] This register sets SYNC-TIP Clamp timing. Clamp Timing Pulse generation and its pulse width can be adjusted. Output signal mode selection of the EXTCLP pin is also possible. For a timing diagram, refer to the SYNC Separation description in the Clamp section. Reserved bits must be set to " 0 ". Sub Address 0x0B bit 7 bit 6 EXTCLP1 EXTCLP0 0 0 bit 5 SCLPWIDTH2 bit 4 SCLPWIDTH1 bit 3 SCLPWIDTH0 bit 2 SCLPSTAT2 Default Value : 0x11 bit 1 bit 0 SCLPSTAT1 SCLPSTAT0 Default Value 0 1 0 0 0 1 Clamp Timing Control Register BIT Register Name bit 0 bit 2 SCLPSTAT0 SCLPSTAT2 Synctip Clamp Start timing0 Synctip Clamp Start timing2 bit R/W R/W Definition Setting the start position of synctip clamp pulse default value is SCLPSTA2 : SCLPSTA0 = 001 [SCLPSTAT2 SCLPSTAT0 ] 000 : 2clks later 001 : 4clks later 010 : 6clks later 011 : 8clks later 100 : 10clks later 101 : 12clks later 110 : 14clks later 111 : 16clks later 1clk is about 37[nsec] Setting the synctip clamp pulse width Default value is SCLPWIDTH2 : SCLPWIDTH0 = 010. [SCLPWIDTH3 SCLPWIDTH0] 000 : 2 clks (74nsec) 001 : 4 clks (148nsec) 010 : 8 clks (296nsec) 011 : 16 clks (592nsec) 100 : 24 clks (888nsec) 101 : 32 clks (1.18usec) 110 : 40 clks (1.48usec) 111 :48 clks (1.78usec) Setting the output the timing EXTCLP-pin. R/W bit 3 bit 5 SCLPWIDTH0 SCLPWIDTH2 Synctip Clamp Pulse Width0 bit Synctip Clamp Pulse Width2 bit bit 6 bit 7 EXTCLP0 EXTCLP1 External Clamp 0 bit External Clamp 1 bit R/W data from [EXTCLP1:EXTCLP0] 00 : Hi-Z (Defaul) 01 : Internal synctip clamp timing pulse. 10 : Internal pedestal clamp timing pulse. 11 : SYNCDET signal Rev.0 78 2003/01 ASAHI KASEI [AK8850] CLAMP TIMING 2 CONTROL REGISTER ( R / W ) [ SUB ADDRESS 0x0C ] This register sets the Pedestal Clamp timing. The timing of the Clamp Timing Pulse generation and its pulse width can be adjusted. For timing diagram,refer to the SYNC-Separation description in the Clamp section. Reserved bits must be set to " 0 ". Sub Address 0x0C bit 7 bit 6 SLCLV1 SLCLV0 0 0 bit 5 PCLPWIDTH2 bit 4 PCLPWIDTH1 bit 3 PCLPWIDTH0 bit 2 PCLPSTAT2 Default Value :0x1C bit 1 bit 0 PCLPSTAT1 PCLPSTAT0 Default Value 0 1 1 1 0 0 CLAMP Timing 2 Control Register BIT Register Name R/W Definition Setting the start position of pedestal clamp pulse. default value is PCLPSTA2 : PCLPSTA0 = 100 [PCLPSTAT2 PCLPSTAT0] 000 : 118 clks (4.37usec) later 001 : 126 clks (4.65usec) later 010 : 132 clks (4.88usec) later 011 : 140 clks (5.18usec) later 100 : 148 clks (5.48usec) later 101 : 156 clks (5.77usec) later 110 : 164 clks (6.07usec) later 111 : 172 clks (6.36usec) later 1clk is about 37[nsec] Setting the pedestal clamp timing pulse width. Default value is PCLPWIDTH2 : PCLPWIDTH0 = 011 bit 0 bit 2 Pedestal Clamp Start timing0 bit PCLPSTAT0 PCLPSTAT2 Pedestal Clamp Start timing2 bit R/W bit 3 bit 5 PCLPWIDTH0 PCLPWIDTH3 Pedestal Clamp Pulse Width0 Pedestal Clamp Pulse Width3 bit R/W bit 6 bit 7 SLCLV0 Slice Level Control bit SLCLV1 R/W [PCLPWIDTH3 PCLPWIDTH0] 000 : 16 clks (592 nsec) 001 : 24 clks (888 nsec) 010 : 28 clks (1.04 usec) 011 : 32 clks (1.18 usec) 100 : 40 clks (1.48 usec) 101 : 44 clks (1.63 usec) 110 : 48 clks (1.78 usec) 111 : 52 clks (1.92 usec) Setting the slice level Default value is 00 [SLCLV1:SLCLV0] = 00 :Sliced 1/4 level above the synctip 01 :Sliced 1/2 level above the synctip 10 :Prohibit to set 11: Sliced 3/8 level above the synctip Rev.0 79 2003/01 ASAHI KASEI [AK8850] PGA1 Gain Control Register (R/W) [Sub Address 0x0D] Sub Address 0x0D bit 7 bit 6 bit 5 bit 4 bit 3 Reserved PGA1[6] PGA1[5] PGA1[4] PGA1[3] Default Value 0 1 0 0 0 PGA1 Gain Control Register BIT Register Name bit 0 bit 6 bit 7 PGA1[0] PGA1[6] Reserved PGA1[0] PGA1[6] bit Reserved bit 2 PGA1[2] 0 Default Value : 0x40 bit 1 bit 0 PGA1[1] PGA1[0] 0 0 R/W R/W R/W Definition Setting PGA1 Gain. This register is available when Control 1 Register is set to [bit-1,0] = [0,0] (AGC Disable) Gain step of PGA is about 0.1dB/LSB. Reserved PGA2 Gain Control Register (R/W) [Sub Address 0x0E] Sub Address 0x0E bit 7 bit 6 bit 5 bit 4 bit 3 Reserved PGA2[6] PGA2[5] PGA2[4] PGA2[3] Default Value 0 1 0 0 0 PGA2 Gain Control Register BIT Register Name bit 0 bit 6 bit 7 PGA2[0] PGA2[6] Reserved PGA2[0] PGA2[6] bit Reserved bit 2 PGA2[2] 0 Default Value : 0x40 bit 1 bit 0 PGA2[1] PGA2[0] 0 0 R/W R/W R/W Definition Setting PGA2 Gain. This register is available when Control 1 Register is set to [bit-1,0] = [0,0] (AGC Disable) Gain step of PGA is about 0.1dB/LSB. Reserved Default Value : 0x40 bit 1 bit 0 PGA3[1] PGA3[0] 0 0 PGA3 Gain Control Register (R/W) [Sub Address 0x0F] Sub Address 0x0F bit 7 bit 6 bit 5 bit 4 bit 3 Reserved PGA3[6] PGA3[5] PGA3[4] PGA3[3] Default Value 0 1 0 0 0 PGA3 Gain Control Register BIT Register Name bit 0 bit 6 bit 7 PGA3[0] PGA3[6] Reserved PGA3[0] PGA3[6] bit Reserved bit 2 PGA3[2] 0 R/W R/W R/W Definition Setting PGA3 Gain. This register is available when Control 1 Register is set to [bit-1,0] = [0,0] (AGC Disable) Gain step of PGA is about 0.1dB/LSB. Reserved Rev.0 80 2003/01 ASAHI KASEI [AK8850] YC SEPARATION CONTROL 1 REGISTER ( R / W ) [ SUB ADDRESS :0x10 ] This register sets YC Separation- related matters. Sub Address 0x10 bit 7 bit 6 Reserved Reserved 0 0 bit 5 Reserved 0 bit 4 bit 3 Reserved CBPFS1 Default 0 0 bit 2 CBPFS0 1 Default Value : 0x06 bit 1 bit 0 YCSEP1 YCSEP0 1 0 YC Separation Control Register Definition BIT Register Name bit 0 ~ bit 1 YCSEP0 ~ YCSEP1 YC Separation bit R/W R/W bit 2 ~ bit 3 CBPFS0 ~ CBPFS1 C Band Pass Filter Select bit R/W Definition Setting YC Separation YCSEP1 YCSEP0 00 : 2D YC-Separation 01 : 1D YC-Separation 10 : Adaptive Y/CSeparation [Default] 11 : Reserved Setting the Bandwidth of Chrominance signal CBPFS1:CBPFS0 00 : Reserved 01 : Wide [Default] 10 : Middle 11 : Narrow Rev.0 81 2003/01 ASAHI KASEI [AK8850] Color Killer Control Register (R/W) [Sub Address 0x11] Sub Address 0x11 bit 7 bit 6 CL_KILL Reserved 1 0 Default Value : 0xAD bit 1 bit 0 CKLVL1 CKLVL0 0 1 bit 5 CKLVL5 1 bit 4 bit 3 CKLVL4 CKLVL3 Default Value 0 1 bit 2 CKLVL2 1 Color Killer Control Register Definition BIT Register Name CKLVL0 bit 1 Color Killer Level ~ CKLVL5 bit 5 R/W R/W Definition Setting the color killer level. The range of color killer level is from -17db to - with 63 step. 0 : - dB 63 : -17dB Default value is 45 (-20dB) Setting value is defined as following formula Color killer level is CKL[dB]. Setting value = 10CKL/20 * 448 Reserved Color killer switch 0 : Color Killer disable. 1 : Color Killer enable[Default] bit 6 bit 7 Reserved CL-KILL Reserved bit Color Killer bit R/W R/W Rev.0 82 2003/01 ASAHI KASEI [AK8850] BRIGHTNESS CONTROL REGISTER ( R / W ) [ SUB ADDRESS 0x12 ] This register controls the Brightness adjustment. Default value ( 0x00 ) corresponds to un-adjusted condition. Sub Address 0x12 bit 7 bit 6 BR7 BR6 0 0 bit 5 BR5 0 bit 4 bit 3 BR4 BR3 Default Value 0 0 bit 2 BR2 0 Default Value : 0x00 bit 1 bit 0 BR1 BR0 0 0 Brightness Control Register Definition BIT Register Name BR0 bit 0 Brightness Control bit ~ ~ BR7 bit 7 R/W R/W Definition Brightness level is defined following formula -286mV Sync signal (without setup) 1 [BR7:BR0]*100/255 -286mV Sync signal (with setup) 1 [BR7:BR0]*108/255 -300mV Sync signal (without setup) 1 [BR7:BR0]*102/255 -300mV Sync signal (with setup) 1 [BR7:BR0]*111/255 CONTRAST CONTROL REGISTER ( R / W ) [ SUB ADDRESS : 0x13 ] This register controls the Contrast adjustment. Default value ( 0x80 ) corresponds to un-adjusted condition. Sub Address 0x13 bit 7 bit 6 CONT7 CONT6 1 0 Default Value : 0x80 bit 1 bit 0 CONT1 CONT0 0 0 bit 5 CONT5 0 bit 4 bit 3 CONT4 CONT3 Default Value 0 0 bit 2 CONT2 0 Contrast Control Register Definition BIT Register Name CONT0 bit 0 Contrast Control bit ~ ~ CONT7 bit 7 R/W R/W Definition Contrast adjustment range is 0 to 2 by 1/256 step. Rev.0 83 2003/01 ASAHI KASEI [AK8850] SATURATION CONTROL REGISTER ( R / W ) [ SUB ADDRESS : 0x14 ] This register controls Saturation adjustments. Default value ( 0x80 ) corresponds to un-adjusted condition. Sub Address 0x14 bit 7 bit 6 SAT7 SAT6 1 0 bit 5 SAT5 0 bit 4 bit 3 SAT4 SAT3 Default Value 0 0 bit 2 SAT2 0 Default Value : 0x80 bit 1 bit 0 SAT1 SAT0 0 0 Saturation Control Register Definition BIT Register Name SAT0 bit 0 Saturation Control bit ~ ~ SAT7 bit 7 R/W R/W Definition Saturation adjustment range is 0 to 2 by 1/256 step. It corresponds to the range between - to 6dB. HUE CONTROL REGISTER ( R / W ) [ SUB ADDRESS : 0x15 ] This register controls HUE adjustments. Default value ( 0x00) corresponds to un-adjusted condition. This register set is valid only when the Composite signal and YC signal are input ( it is invalid with Component input signasl ). Sub Address 0x15 bit 7 bit 6 HUE7 HUE6 0 0 Default Value : 0x00 bit 1 bit 0 HUE1 HUE0 0 0 bit 5 HUE5 0 bit 4 bit 3 HUE4 HUE3 Default Value 0 0 bit 2 HUE2 0 HUE Control Register Definition BIT Register Name HUE0 bit 0 HUE Control bit ~ ~ HUE7 bit 7 R/W R/W Definition The range of Hue adjustment can be set form -90deg. to 90deg. by 1/256 Step Set with 2's complement value. Rev.0 84 2003/01 ASAHI KASEI [AK8850] POWER SAVE REGISTER ( R / W ) [ SUB ADDRESS : 0x1C ] Controls the transition to Power Save mode. Recovery from the Power Save mode is done by writing " 0 " to PS-bit. Sub Address 0x1C bit 7 bit 6 Reserved Reserved 0 0 bit 5 Reserved 0 bit 4 bit 3 PLLRST ADC3 Default Value 0 0 bit 2 ADC2 0 Default Value : 0x00 bit 1 bit 0 ADC1 PS 0 0 Power Save Register Definition BIT Register Name bit 0 PS Power Save bit R/W R/W R/W bit 1 ADC1 AD1 Save bit R/W bit 2 ADC2 ADC2 Save bit bit 3 bit 4 bit 5 ADC3 PLLRST Reserved ADC3 Save bit PLL Reset bit Reserved bit R/W Definition Power Save Mode setting register bit 0 : Switch to the Active mode from the Power Save Mode 1 : Switch to the Power Save Mode Power save mode for ADC1 0 : Switch to the Active mode 1 : Switch to the Power save mode Power save mode for ADC2 0 : Switch to the Active mode 1 : Switch to the Power save mode Power save mode for ADC3 0 : Switch to the Active mode 1 : Switch to the Power save mode Reset the PLL control Circuit. Set to "1 " and set to "0" after setting "1". Reserved R/W bit 7 Rev.0 85 2003/01 ASAHI KASEI [AK8850] REQUEST VBI INFO REGISTER ( W ) [ SUB ADDRESS : 0x1F ] This register controls VBI operations, including Closed- Caption, Extended data, VBID and WSS. The AK8850 is put into a wait condition for each data when " 1 " is written into each bit. When the decoding is completed, " 1" is written into each bit of the [ STATUS 2 REGISTER ] and the decoded data are stored in the Closed-Caption Data1 / Data2,CCEXTENDED Data1 / Data2,VBID Data1 / Data2 and WSS Data1 / Data2 registers respectively. Sub Address 0x1F bit 7 bit 6 Reserved Reserved 0 0 bit 5 Reserved 0 bit 4 bit 3 WSSRQ VBIDRQ Default Value 0 0 bit 2 EXTRQ 0 bit 1 CCRQ 0 bit 0 ASPECTRQ 0 Request VBI Info Register Definition BIT Register Name bit 0 ASPECTRQ ASPECT Request bit R/W W bit 1 CCRQ Closed Caption Request bit W bit 2 EXTRQ Extended Data Request bit W bit 3 VBIDRQ VBID Request bit W bit 4 bit 5 WSSRQ WSS Request bit W Definition Request to decode ASPECT Signal 0: 1 : Request Request to decode Closed Caption data 0: 1 : Request Request to decode Extended data 0: 1 : Request Request to decode VBID data 0: 1 : Request Request to decode WSS data 0: 1 : Request Reserved bit Reserved bit 7 Reserved bit W Rev.0 86 2003/01 ASAHI KASEI [AK8850] STATUS 1 REGISTER ( R ) [ SUB ADDRESS 0x20 ] This register shows the internal status of the AK8850. Sub Address 0x20 bit 7 bit 6 COLKIL FIELD Status 1 Register Definition BIT Register Name bit 0 NOSIG bit 5 SCLKMODE1 bit 4 SCLKMODE0 bit 3 VSQLY bit 2 FRMSTD bit 1 VLOCK bit 0 NOSIG R/W R No Signal Indicates bit bit 1 VLOCK Vsync Lock Indicates bit R bit 2 FRMSTD Frame Standard Indicates bit R bit 3 NSTD Non Standard Signal Indicates bit R bit 4 bit 5 SCLKMODE0 SCLKMODE1 Status Current Clock mode bit R bit 6 FIELD Field Status bit bit 7 COLKIL Color Killer Active bit R Definition No signal indicates This data also output from NSIG pin. 0 : Signal is input 1 : No signal is input Shows synchronization states of the input signal. 0 : Unsynchronaized to the input signal. 1 : Synchronaized to the input signal. Showing the Input video signal quality. 0 : Not 525/625 interlace video signal. 1 : 525/625 is interlace video signal. Showing the input video signal quality. This bit reflects the SCH status. For component video signal input, this bit depends on FRMSTD-bit. (This bit becomes 0 at FRMSTD-bit is 1) The data of this bit is also output from NSTD pin 0 : Standard signal is input. 1 : Non-standard signal is input. Showing the clock-mode. [ CLKMODE1:CLKMODE0 ] = 00 : Working with Fixed clock mode. 01 : Working with Line-Locked Clock mode 10 : Reserved 11 : Working with Frame-Locked Clock mode Showing the Field status 0 : ODD Field 1 : EVEN Field Showing the Color Killer Status 0 : Color Killer is not active 1 : Color Killer is active Rev.0 87 2003/01 ASAHI KASEI [AK8850] STATUS 2 REGISTER ( R ) [ SUB ADDRESS 0x21 ] This register indicates the internal status of the AK8850. Sub Address 0x21 bit 7 bit 6 APS1 APS0 Status 2 Register Definition BIT Register Name bit 0 ASPECT bit 5 Reserved bit 4 WSS bit 3 VBID bit 2 EXT bit 1 CC bit 0 ASPECT R/W R ASPECT Detect bit bit 1 CC Closed Caption detect bit R bit 2 EXT Extended Renewal bit R bit 3 VBID VBID Renewal bit R bit 4 bit 5 WSS WSS Renewal bit R Definition Status of APSECT signal. 0 : Low (Normal ) 1 : High (Wide) Closed Caption Data detect bit 0 : Closed Caption is not detected. 1 : Closed Caption is found. Extended Data detect bit 0 : Extended data is not detected. 1 : Extended data is found. VBID data detect bit 0 : VBID data is not detected. 1 : VBID data is found. WSS Data detect bit. 0 : WSS data is not detected. 1 : WSS data is found. Reserved Reserved bit 7 Reserved bit R Rev.0 88 2003/01 ASAHI KASEI [AK8850] CLOSED-CAPTION 1 REGISTER / CLOSED-CAPTION 2 REGISTER ( R ) [ SUB ADDRESS 0x22 / 0x23 ] These registers show the Closed-Caption information which is encoded on Line 21 / 22 ( 525 system / 625 system ). Sub Address 0x22 bit 7 bit 6 CC7 CC6 Sub Address 0x23 bit 7 bit 6 CC15 CC14 bit 5 CC5 bit 4 CC4 bit 3 CC3 bit 2 CC2 bit 1 CC1 bit 0 CC0 bit 5 CC13 bit 4 CC12 bit 3 CC11 bit 2 CC10 bit 1 CC9 bit 0 CC8 Closed Caption 1 Register Definition BIT Register Name CC0 bit 0 Closed Caption Data bit ~ ~ CC7 bit 7 Closed Caption 2 Register Definition BIT Register Name CC8 bit 0 Closed Caption Data bit ~ ~ CC15 bit 7 R/W R Definition Closed Caption Data R/W R Definition Closed Caption Data EXTENDED DATA 1 REGISTER / EXTENDED DATA 2 REGISTER ( R ) [ SUB ADDRESS 0x24 /0x25 ] These registers show the EXTENDED DATA information which is encoded on Line 284 / 335 ( 525 system / 625 system ). Sub Address 0x24 bit 7 bit 6 EXT7 EXT6 Sub Address 0x25 bit 7 bit 6 EXT15 EXT14 bit 5 EXT5 bit 4 EXT4 bit 3 EXT3 bit 2 EXT2 bit 1 EXT1 bit 0 EXT0 bit 5 EXT13 bit 4 EXT12 bit 3 EXT11 bit 2 EXT10 bit 1 EXT9 bit 0 EXT8 Extended Data 1 Register Definition BIT Register Name EXT0 bit 0 Extended Data bit ~ ~ EXT7 bit 7 Extended Data 2 Register Definition BIT Register Name EXT8 bit 0 Extended Data bit ~ ~ EXT15 bit 7 R/W R Definition Extended Data R/W R Definition Extended Data Rev.0 89 2003/01 ASAHI KASEI [AK8850] VBID 1 REGISTER / VBID 2 REGISTER ( R ) [SUB ADDRESS 0x26 / 0x27 ]. These registers show the VBID information which is encoded on Line 20 / 20 and Line 283 / 333 ( 525 system / 625 system ). Sub Address 0x26 bit 7 bit 6 VBID7 VBID8 Sub Address 0x27 bit 7 bit 6 Reserved Reserved bit 5 VBID9 bit 4 VBID10 bit 3 VBID11 bit 2 VBID12 bit 1 VBID13 bit 0 VBID14 bit 5 VBID1 bit 4 VBID2 bit 3 VBID3 bit 2 VBID4 bit 1 VBID5 bit 0 VBID6 VBID 1 Register Definition BIT Register Name VBID14 bit 0 VBID Data bit ~ ~ VBID7 bit 7 VBID 2 Register Definition BIT Register Name VBID6 bit 0 VBID Data bit ~ ~ VBID1 bit 5 bit 6 Reserved Reserved bit bit 7 R/W R Definition VBID Data R/W R Definition VBID Data R Reserved bit WSS 1 REGISTER / WSS 2 & ASPECT DATA REGISTER ( R )[ SUB ADDRESS 0x28 / 0x29 ] These registers show WSS information encoded on Line 23. Sub Address 0x28 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 G2-7 G2-6 G2-5 G2-4 G1-3 G1-2 G1-1 Sub Address 0x29 bit 7 bit 6 ASPDAT Reserved bit 0 G1-0 bit 5 G4-13 bit 4 G4-12 bit 3 G4-11 bit 2 G3-10 bit 1 G3-9 bit 0 G3-8 WSS 1 Register Definition BIT Register Name G1-0 bit 0 Group1 Data bit ~ ~ G1-3 bit 3 G2-4 bit 4 Group2 Data bit G2-7 bit7 WSS 2 & Aspect Data Register Definition BIT Register Name G3-8 bit 0 Group3 Data bit ~ ~ G3-10 bit 2 G4-11 bit 3 Group4 Data bit G4-13 bit 5 bit 6 Reserved Reserved bit bit 7 ASPDAT Aspect Data bit R/W R Definition WSS Group 1 data (Aspect ration) R WSS Group 2 data (Enhanced services) R/W R R Definition WSS Group 3 data (Subtitles) WSS Group 4data (Reserved) R R Reserved bit Video aspect data Rev.0 90 2003/01 ASAHI KASEI [AK8850] DEVICE & REVISION ID REGISTER ( R ) [ SUB ADDRESS 0x2E ] This register indicates the device ID and Revision number of the AK8850. The Device ID is 0x00. The initial Revision number is 0x00. Revision number is renewed only when the control software needs to be modified. Sub Address 0x2E bit 7 bit 6 DID3 DID2 bit 5 DID1 bit 4 DID0 bit 3 REV3 bit 2 REV2 bit 1 REV1 bit 0 REV0 Revision Register Definition BIT Register Name REV0 bit 0 Revision bit ~ ~ REV3 bit 3 DID0 bit 4 Device ID DID3 bit 7 R/W R R Definition Indicates Revision data REV3 REV0 0x00 Indicates Device ID AK8850 is 0x00 Rev.0 91 2003/01 ASAHI KASEI [AK8850] CLOCK CONTROL-1 REGISTER ( R /W ) [ SUB ADDRESS 0x36 ] This register controls the Clock transition time in Auto Clock mode which is set by [ bit 7 : bit 6 ] of the Auto Select ( CONTROL 2 REGISTER ( 0x09 )) Sub Address 0x36 bit 7 bit 6 TTC1 TTC0 1 0 bit 5 SKEWTH5 0 bit 4 bit 3 SKEWTH4 SKEWTH3 Default Value 0 0 bit 2 SKEWTH2 1 Default Value : 0x84 bit 1 bit 0 SKEWTH1 SKEWTH0 0 0 Clock Control-1 Register Definition BIT Register Name SKEWTH0 Skew Detection Threshold bit 0 ~ SKEWTH5 bit 5 Clock Transition Time Constant TTC0 bit 6 bit 7 TTC1 R/W R/W Definition Set the threshold value for VTR Skew detection. Threshold value = [SKEWTH5:SKEWTH0] Time Constant for clock mode transition. 0 : slowest 3 : fastest CLOCK CONTROL-2 REGISTER ( R / W ) [ SUB ADDRESS 0x37 ] This register controls the Clock Transition time in Auto Clock mode which is set by [ bit 7 : bit 6 ] of the Auto Select Control 2 Register ( 0x09 ). Sub Address 0x37 bit 7 bit 6 LNFRTH7 LNFRTH6 0 1 Default Value : 0x7C bit 1 bit 0 LNFRTH1 LNFRTH0 0 0 bit 5 LNFRTH5 1 bit 4 bit 3 LNFRTH4 LNFRTH3 Default Value 1 1 bit 2 LNFRTH2 1 Clock Control-2 Register Definition BIT Register Name LNFRTH0 Lint to Frame Threshold Level bit 0 Control bit ~ LNFRTH7 bit 7 R/W R/W Definition The threshold parameter from Line-Lock clock mode to Frame-Lock clock mode. Rev.0 92 2003/01 ASAHI KASEI [AK8850] CLOCK CONTROL- 3 REGISTER ( R / W ) [ SUB ADDRESS 0x38 ] This register controls the Clock Transition time in Auto Clock mode which is set by [ bit 7 : bit 6 ] of the Auto Select Control 2 Register ( 0x09 ). Sub Address 0x38 bit 7 bit 6 FRLNTH7 FRLNTH6 0 0 bit 5 FRLNTH5 1 bit 4 bit 3 FRLNTH4 FRLNTH3 Default Value 1 1 bit 2 FRLNTH2 1 Default Value : 0x3C bit 1 bit 0 FRLNTH1 FRLNTH0 0 0 Clock Control 3 Register Definition BIT Register Name FRLNTH0 Frame to Line Threshold Level bit 0 Control bit ~ FRLNTH7 bit 7 R/W R/W Definition The threshold parameter from Frame-Lock clock mode to Line-Lock clock mode. CLOCK CONTROL-4 REGISTER ( R / W ) [ SUB ADDRESS : 0x39 ] This register controls the Clock Transition time in Auto Clock mode which is set by [ bit 7 : bit 6 ] of the Auto Select Control 2 Register ( 0x09 ). Sub Address 0x39 bit 7 bit 6 FRFXTH7 FRFXTH6 1 1 Default Value : 0xDC bit 1 bit 0 FRFXTH1 FRFXTH0 0 0 bit 5 FRFXTH5 0 bit 4 bit 3 FRFXTH4 FRFXTH3 Default Value 1 1 bit 2 FRFXTH2 1 Clock Control 4 Register Definition BIT Register Name FRFXTH0 Frame to Fix Clock Threshold bit 0 Level Control bit ~ FRFXTH7 bit 7 R/W R/W Definition The threshold parameter from Frame-Lock clock mode to Fixed clock mode. CLOCK CONTROL-5 REGISTER ( R / W ) [ SUB ADDRESS 0x3A ] This register controls the Clock Transition time in clock Auto Mode set by ( bit 7 : bit 6 ) of the Auto Select Control 2 Register ( 0x09 ). Sub Address 0x3A Default Value : 0x04 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 FXLNTH7 FXLNTH6 FXLNTH5 FXLNTH4 FXLNTH3 FXLNTH2 FXLNTH1 FXLNTH0 Default Value 0 0 0 0 0 1 0 0 Clock Control 5 Register Definition BIT Register Name FXLNTH0 Fix Clock to Line Threshold bit 0 Level Control bit ~ FXLNTH7 bit 7 R/W R/W Definition The threshold parameter for switching between the Fixed clock and Line-Lock clock modes. Rev.0 93 2003/01 ASAHI KASEI [AK8850] PLL CONTROL REGISTER ( R / W ) [ SUB ADDRESS 0x46 ] PLL control register. Sub Address 0x46 bit 7 bit 6 Reserved LPGAUTO 0 0 bit 5 LPG3 0 bit 4 bit 3 LPG2 LPG1 Default Value 0 0 bit 2 LPG0 0 Default Value : 0x00 bit 1 bit 0 LPGM1 LPGM2 0 0 PLL Control Register Definition BIT Register Name bit 0 LPGM2:LPGM Loop Gain Control bit 1 bit 1 R/W R/W bit 2 LPG0:LPG3 bit 5 Loop Gain Control bit R/W bit 6 LPGAUTO Loop Gain Auto bit R/W Definition FRAME LOCK Mode EC gain LPGM[1:2] = 00 : x 1 (Default 01 : x 2 10 : x 4 11 : x 8 LPG[1:0] Line Lock mode EC gain[1:0] 00 : x 1 (Default 01 : x 1/2 10 : x 4 11 : x 2 LPG[2] CP gain 0 : x 1 (Default 1:x2 LPG[3] GM gain 0 : x 1 (Default) 1:x2 0 : Manual Default 1 : Auto In case of Auto mode setting, LPG2 and LPG3 settings are ignored and the CP and GM gains are switched automatically depending on the PLL mode. Line-Lock mode: CP x 1 (Low), GM : x1 (Low) Frame-Lock mode : CP : x 2 (High) , GM : x 2 (High) Reserved bit 7 Reserved Reserved bit R/W Rev.0 94 2003/01 ASAHI KASEI [AK8850] PLL DAC SET REGISTER ( R / W ) [ SUB ADDRESS 0x47 ] PLL control register. Sub Address 0x47 bit 7 bit 6 PLLDACI7 PLLDACI6 1 0 bit 5 PLLDACI5 0 bit 4 bit 3 PLLDACI4 PLLDACI3 Default Value 0 0 bit 2 PLLDACI2 0 Default Value : 0x80 bit 1 bit 0 PLLDACI1 PLLDACI0 0 0 PLL DAC Set Register Definition BIT Register Name PLLDACI0 bit 0 PLL DAC INPUT bit PLLDACI7 bit 7 R/W R/W Definition Adjust the External VCXO center frequency with this register. LSB is always disabled. Rev.0 95 2003/01 ASAHI KASEI [AK8850] 9. System connection example Digital 3.3V Micro Processor 2 (I C Controller) Video IN Anti Areasing FIlter 39 0.1u PD AIN1..6 /INT /RESET SCL SDA SELA 39 620 0.1u SYNC1..3 D[7..0] 510p CLPCAP1 CLPCAP2 FBPCAP1 FBPCAP2 FBPCAP3 0.1u 0.1u 33n 33n 33n NSTD VRP VCOM VRN VREF 0.1u 0.1u 0.1u 0.1u NSIG CLK27MOUT HALFCLKOUT DVALID HSYNC VSYNC FIELD FRAME0 FRAME1 AK8850 FLPF 3.3 0.03uF 0.3uF FLPFC LLPF 0.34uF 18k LLPFC 3.4uF 10k IRefR1 TEST[11:0] TD1[9:0] TD2[9:0] Control Voltage IVCXO 27MHz VCXO CLKINV 27MHz Clock Analog 3.3V CLK AVDD AVSS DVSS DVDD Digital 3.3V 10uF 0.1uF 0.1uF 10uF Analog GND Digital GND Rev.0 96 2003/01 ASAHI KASEI [AK8850] 10. Package 100pin LQFP 16.0 0.2 14.0 1.70 Max 1.40 0.20 Max 75 76 51 50 16.0 0.2 100 1 25 0.5 0.22 0.05 26 0.10 M 0.17 0.05 1.0 0 ~ 10 0.10 0.5 0.2 Package & Lead frame material Package molding compound Lead frame material Lead frame surface treatment: Epoxy Cu Solder plate Rev.0 97 2003/01 ASAHI KASEI [AK8850] 11. Marking AK8850 1 1) AKM : AKM Logo 2) AK8850 : Marketing Code 3) XXXXXXX (7digits) : Date Code 4) Pin #1 indication Rev.0 98 2003/01 ASAHI KASEI [AK8850] IMPORTANT NOTICE These products and their specifications are subject to change without notice. Before considering any use or application, consult the Asahi Kasei Microsystems Co., Ltd. (AKM) sales office or authorized distributor concerning their current status. AKM assumes no liability for infringement of any patent, intellectual property, or other right in the application or use of any information contained herein. Any export of these products, or devices or systems containing them, may require an export license or other official approval under the law and regulations of the country of export pertaining to customs and tariffs, currency exchange, or strategic materials. AKM products are neither intended nor authorized for use as critical components in any safety, life support, or other hazard related device or system, and AKM assumes no responsibility relating to any such use, except with the express written consent of the Representative Director of AKM. As used here: (a) A hazard related device or system is one designed or intended for life support or maintenance of safety or for applications in medicine, aerospace, unclear energy, or other fields, in which its failure to function or perform may reasonably be expected to result in loss of life or in significant injury or damage to person or property. (b) A critical component is one whose failure to function or perform may reasonably be expected to result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it, and which must therefore meet very high standards of performance and reliability. It is the responsibility of the buyer or distributor of an AKM product who distributes, disposes of, or otherwise places the product with a third party to notify that party in advance of the above content and conditions, and the buyer or distributor agrees to assume any and all responsibility and liability for and hold AKM harmless from any and all claims arising from the use of said product in the absence of such Rev.0 99 2003/01 |
Price & Availability of AK8850
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |