View MC03AX1456RT_408080.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Product Preview
ADSL Line Driver
The MC03AX1456 ADSL Line Driver provides a single chip analog front end to interface the ADSL Transceiver to the line transformer. The MC03AX1456CO is designed to fulfill the central office requirements. The MC03AX1456RT is optimized for use at the remote terminal (i.e. consumer premises). The ADSL Line Driver provides three differential ports: a transmit and a receive port to interface to the ADSL Transceiver's transmit and receive ports, respectively; and a bidirectional line port. The transmit port incorporates a high-pass filter and a programmable gain stage with three settings. The receive port incorporates a programmable HF boost and a programmable gain stage, each with three settings, as well as a high pass-filter.
MC03AX1456CO MC03AX1456RT
* * * * * * * * * * *
Hybrid balance for echo cancellation Defined termination impedance to the line Programmable transmit gain (3 settings) Programmable receive gain (3 setting) Programmable HF boost (3 setting) Transmit band for CO is 26KHz-1104KHz Transmit band for the RT is 26KHz-138KHz Frequency ripple <0.5dB (CO and RT) Standby mode for lower power dissipation (CO and RT) 15V 10% supply voltages 30-pin HSOP package
HSOP PACKAGE CASE 979A-02
ADSL System Block Diagram
MC03AX1456CO Line Driver/Hybrid 0-1 Mbps MC03AX1456RT Line Driver/Hybrid 0-1 Mbps
0-8 Mbps
0-8 Mbps
Line Transformers and POTS Splitters
Host uP MC145650 Copper Gold ADSL Transceiver MC145650 Copper Gold ADSL Transceiver
Host uP
Central Office Unit
Remote Unit
This document contains information on a product under development. Motorola reserves the right to change or discontinue this product without notice. 11/96
(c) Motorola, Inc. 1996
1
REV 0.1
MC03AX1456CO MC03AX1456RT
TX from ADSL Transceiver
High Pass Filter High Pass Filter
Prog Gain
Prog Gain Hybrid Balance and Termination Impedance Prog HF Boost Prog HF Boost High Pass Filter High Pass Filter POTs Splitter
Prog Gain RX to ADSL Transceiver Prog Gain
Figure 1. Functional Block Diagram of the MC03AX1456 Line Driver MAXIMUM RATINGS*
Symbol VCC VEE VIN VOUT IIN IOUT TSTG Parameter Positive Supply Voltage (Referenced to GND) Negative Supply Voltage (Referenced to GND) Input Voltage (Referenced to GND) Output Voltage (Referenced to GND) Input Current Output Current Storage Temperature Range Value +18 -18 TBD TBD TBD TBD -65 to +150 Unit V V V V mA mA C
* Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions.
RECOMMENDED OPERATING CONDITIONS
Symbol VCC V-Sup TJ Positive Supply Voltage Negative Supply Voltage Junction Temperature Parameter Min +13.5 -13.5 Typ +15.0 -15.0 Max +16.5 -16.5 150 Unit V V C
MOTOROLA
2
ECLinPS and ECLinPS Lite DL140 -- Rev 3
MC03AX1456CO MC03AX1456RT
OUTLINE DIMENSIONS
HSOP PACKAGE CASE 979A-02 ISSUE A
E2 h
X 45 _ EXPOSED HEATSINK AREA
E3
D2
1
30
D -A-
28X
D1
e
15 16
E1 -B-
15X
E4
S
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DATUM PLANE -H- IS LOCATED AT BOTTOM OF LEAD AND IS COINCIDENT WITH THE LEAD WHERE THE LEAD EXITS THE PLASTIC BODY AT THE BOTTOM OF THE PARTING LINE. 4. DIMENSIONS D AND E1 DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE PROTRUSION IS 0.150 (0.006) PER SIDE. DIMENSIONS D AND E1 DO INCLUDE MOLD MISMATCH AND ARE DETERMINED AT DATUM PLANE -H-. 5. DIMENSION b DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE b DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. DATUMS -A- AND -B- TO BE DETERMINED AT DATUM PLANE -H-. MILLIMETERS MIN MAX 3.100 3.450 0.050 0.200 3.050 3.250 15.800 16.000 12.270 12.470 0.900 1.100 13.950 14.450 10.900 11.100 2.500 2.700 7.000 7.200 2.700 2.900 0.840 1.100 0.350 BSC 0.350 0.475 0.350 0.432 0.230 0.320 0.230 0.280 0.800 BSC --- 1.100 q 0_ 8_ aaa 0.200 bbb 0.200 ccc 0.100 DIM A A1 A2 D D1 D2 E E1 E2 E3 E4 L L1 b b1 c c1 e h INCHES MIN MAX 0.122 0.136 0.002 0.008 0.120 0.128 0.622 0.630 0.483 0.491 0.035 0.043 0.549 0.569 0.429 0.437 0.098 0.106 0.276 0.284 0.106 0.114 0.033 0.043 0.014 BSC 0.014 0.019 0.014 0.017 0.009 0.013 0.009 0.011 0.031 BSC --- 0.043 0_ 8_ 0.008 0.008 0.004
E CB
bbb
M
BOTTOM VIEW
A DETAIL Y
-H- -C-
DATUM PLANE SEATING PLANE
b ccc C W W
GAUGE PLANE
q
L (1.600) (0.063)
A1 DETAIL Y
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 or 602-303-5454 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com
ECLinPS and ECLinPS Lite DL140 -- Rev 3 3
CEE E CCCC ECCC EE
aaa
M
L1
b1 c1 c
CA
S
SECTION W-W
JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-81-3521-8315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298
*MC03AX1456/D*
MC03AX1456/D MOTOROLA

▲Up To Search▲

Price & Availability of MC03AX1456RT

	To Download MC03AX1456RT Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .