| |
|
 |
STMICROELECTRONICS[STMicroelectronics]
ST Microelectronics
|
| Part No. |
L6918DTR L6918 L6918A L6918AD L6918ADTR L6918D 9117
|
| OCR Text |
... pin to the sense point must be routed as close as possible to the PGNDS1 net in order to couple in common mode any picked-up noise. 14 15 PGNDS1 PGNDS2 Channel 1 Power Ground sense pin. The net connecting the pin to the sense point must be... |
| Description |
From old datasheet system
5 BIT PROGRAMMABLE MULTIPHASE CONTROLLER
5 BIT PROGRAMMABLE MULTIPHASE CONTROLLER
|
| File Size |
758.33K /
35 Page |
 View
it Online |
Download Datasheet
|
| |
|
|
Mallory performance clu...
|
| Part No. |
6530
|
| OCR Text |
...to performance. wires should be routed away from sharp edges and engine heat sources. if there are two wires that are next to each other in the engine's fring order, the wires should be routed away from each other to avoid inducing a spar... |
| Description |
The Gray Tach Output Terminal produces
|
| File Size |
679.29K /
20 Page |
View
it Online |
Download Datasheet |
| |
|
|
Integrated Silicon Solu...
|
| Part No. |
IS43DR00-001
|
| OCR Text |
...om the same net group should be routed on the same layer. 2. signals from byte group, such as dqs, dm and 8 bits of dq, mus t be routed in the same layer 3. t he deviation of signal propagation delay is dependent on the timing bud... |
| Description |
ISSI DDR2 SDRAM Design Considerations Guide
|
| File Size |
743.88K /
5 Page |
View
it Online |
Download Datasheet |
| |
|
|
MAXIM - Dallas Semiconductor
|
| Part No. |
DS1077LZ-40 DS1077LZ-66
|
| OCR Text |
...uency (master clk) that can be routed directly to the outputs (out0 & out1) or through separate prescalers (p0 & p1). out1 can also be routed through an additional divider (n). the prescaler (p0) divides the mast er clock by 1, 2, 4... |
| Description |
3V EconOscillator/Divider
|
| File Size |
281.99K /
21 Page |
View
it Online |
Download Datasheet |
| |
|
|
STMICROELECTRONICS[STMicroelectronics]
|
| Part No. |
L6919ETR L6919E
|
| OCR Text |
... pin to the sense point must be routed as close as possible to the PGNDS net in order to couple in common mode any picked-up noise. Channel 1 Power Ground sense pin. The net connecting the pin to the sense point must be routed as close as p... |
| Description |
From old datasheet system
5 BIT PROGRAMMABLE DUAL-PHASE CONTROLLER WITH DYNAMIC VID MANAGEMENT
|
| File Size |
603.30K /
33 Page |
View
it Online |
Download Datasheet |
| |
|
|
Mallory performance clu...
|
| Part No. |
PN6200
|
| OCR Text |
...to performance. wires should be routed away from sharp edges and engine heat sources. if there are two wires that are next to each other in the engine's fring order, the wires should be routed away from each other to avoid inducing a spar... |
| Description |
MSD 6 Series
|
| File Size |
1,443.26K /
24 Page |
View
it Online |
Download Datasheet |
| |
|
|
Mallory performance clu...
|
| Part No. |
6A-PN6201 6AL-PN6425
|
| OCR Text |
...to performance. wires should be routed away from sharp edges and engine heat sources. if there are two wires that are next to each other in the engines fring order, the wires should be routed away from each other to avoid inducing a spark... |
| Description |
MSD Digital 6A and 6AL Ignition Control
|
| File Size |
1,435.18K /
20 Page |
View
it Online |
Download Datasheet |
| |
|
|
MICROSEMI CORP-ANALOG MIXED SIGNAL GROUP
MICROSEMI[Microsemi Corporation]
|
| Part No. |
LX7202-22ISF LX7202 LX7202-15ISF
|
| OCR Text |
... Pin 6 D+ from the connector is routed to Pin 3 (1.5 k pull-up resistor) and Pin 4 to the D+ line of the USB Transceiver D- from the connector is routed to Pin 2 and Pin 5 to the D- line of the USB Transceiver
Host USB Transceiver
cab... |
| Description |
Integrated EMI Filters and TVS diodes; Package: SF (6 Pin SOT-23);
EMI Filter & ESD Protection for Up Stream USB Ports
|
| File Size |
277.04K /
7 Page |
View
it Online |
Download Datasheet |
| |
|
|
MAXIM[Maxim Integrated Products]
|
| Part No. |
MAX2160_1 MAX2160 MAX2160EVKIT MAX21601
|
| OCR Text |
...or (C19) ground returns must be routed back to the GNDVCO pin and then connected to the overall ground plane at that point (GNDVCO). All loop filter component grounds (C27-C30) and the VCCCP bypass capacitor (C17) ground must all be routed ... |
| Description |
Evaluation Kit
|
| File Size |
408.50K /
9 Page |
View
it Online |
Download Datasheet |
|
Price and Availability
|
